Ce_(0.8)Nd_(0.2)O_(1.9)-La_(0.95)Sr_(0.05)Ga_(0.9)Mg_(0.1)O_(3-δ)固体复合电解质的结构和电性能

采用溶胶-凝胶法分别制备La0.95Sr0.05Ga0.9Mg0.1O3-δ(LSGM)和Ce0.8Nd0.2O1.9(NDC)电解质,并在NDC溶胶中加入0-15%(w,质量分数)的LSGM预烧粉体制得NDC-LSGM复合电解质,研究不同质量比复合电解质的结构和电性能.采用X射线衍射(XRD)、场发射扫描电子显微镜(FE-SEM)和X能量色散谱仪(EDS)对样品进行结构表征,交流(AC)阻抗谱测试样品导电性能.结果表明:NDC-LSGM复合体系主要由立方萤石结构相、钙钛矿结构相和杂质相组成;LSGM的添加可促进晶粒的生长,产生大量相界面,清除或降低SiO2有害影响,明显提高晶界导电性;LSGM质量分数为10%的样品NL10具有最高晶界电导率和总电导率,400°C时NL10的晶界电导率σgb和总电导率σt分别为12.15×10-4和3.49×10-4S cm-1,与NDC的σgb(1.41×10-4S cm-1)和σt(1.20×10-4S cm-1)相比分别提高了7.62和1.91倍,总电导率的提高主要归因于晶界电导率的影响.     

Li_(3.22)Na_(0.569)Mn_(5.78)O_(12.0)的电化学性能

以L iOH.H2O和Mn(CH3COO)2.2H2O作原料,应用微波-固相两段烧结法合成具有L i4Mn5O12结构特征,组成为L i3.22Na0.569Mn5.78O12.0的锂离子电池正极材料.XRD分析表明,在380℃的后处理温度下,微波烧结前处理有利于生成纯L i4Mn5O12尖晶石相.充放电实验表明,在4.5~2.5V电压区间,新制样品的初始放电容量为132 mAh.g-1,100循环的容量衰减率为6.8%;4个月存放样的初始放电容量为122 mAh.g-1,100循环的容量衰减率为17.4%.表现出较好的充放电性能和循环寿命.微波烧结使样品的Mn-O键被加强.     

La_(0.7)Pr_(0.15)Nd_(0.05)Mg_(0.3)Ni_(3.3-x)Co_(0.2)Al_(0.1)(Co_(0.75)Mn_(0.25))_x(x=0.0,0.2,0.4,0.6)的电化学性能研究

在Ar气保护下用悬浮熔炼制备La0.7Pr0.15Nd0.05Mg0.3N i3.3-xCo0.2A l0.1(Co0.75Mn0.25)x(x=0.0,0.2,0.4,0.6)合金,系统研究了Co和Mn对合金储氢性能和电化学性能的影响。XRD相分析表明,合金相主要由(La,Pr)(N i,Co)5,LaMg2N i9,(La,Nd)2N i7和LaN i3相组成;添加Co和Mn后合金中(La,Pr)(N i,Co)5,(La,Nd)2N i7和LaN i3相晶胞体积增加,LaMg2N i9相晶胞体积变小。合金放氢PCT曲线测试表明,随着合金中Co和Mn含量的增加,合金吸氢量先减小后增加,放氢平台压下降,合金氢化物稳定性增加。合金电极电化学性能测试表明,添加Co和Mn使合金电极放电容量减小,容量保持率S100从53.2%(x=0.0)增加到63.0%(x=0.6),合金电极的电循环稳定性增强,高倍率放电性能HRD1500先增加后减小。此外,合金电极的极化电阻先减小后增加,交换电流密度、循环伏安特性阳极峰电流密度和极限电流密度先增加后减小,合金内氢原子扩散系数先增加后减小,表明添加适量的Co和Mn可以提高合金电...     

Novel Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ) membranes for POM

A novel cobalt-free perovskite based on Ba_(0.5)Sr_(0.5)Fe_(0.8)Zn_(0.2)O_(3-δ)(BSFZ)were prepared by EDTA-citric acid method.The lattice constants of the BSFZ perovskite were characterized by in situ high-temperature X-ray diffraction(HTXRD).The thermal expansion coefficient of BSFZ is 10.5×10~(-6)K~(-1),which is lower than that of cobalt-based perovskite materials.The BSFZ membrane was also used to construct reactors for the partial oxidation of methane(POM)to syngas.Results show that the BSFZ membrane...     

双水相萃取法分离铍(Ⅱ)、铁(Ⅲ)与铁(Ⅱ)、铬(Ⅲ)、锰(Ⅱ)、铝(Ⅲ)

研究了在聚乙二醇2000(PEG)-硫酸钠(Na2SO4)-邻苯二酚紫(PV)体系中铍(Ⅱ)、铁(Ⅲ)、铁(Ⅱ)、铝(Ⅲ)、铬(Ⅲ)、锰(Ⅱ)的萃取行为。试验结果表明,铍(Ⅱ)在pH 3.5-7.0及铁(Ⅲ)在pH 4.0-7.0范围内可以被PEG相几乎完全萃取,而铝(Ⅲ)、铬(Ⅲ)在pH 1.0-7.0、锰(Ⅱ)在pH 1.0-4.5、铁(Ⅱ)在pH 1.0-4.5则不被萃取。从而实现了将铍(Ⅱ)(pH 3.5)、铁(Ⅲ)(pH 5.0)与铝(Ⅲ)、铬(Ⅲ)、锰(Ⅱ)、铁(Ⅱ)混合离子的定量分离。同时探讨了PEG相的萃取机理。     

Synthesis and Crystal Structure of Trans-diaquabis(hexamethylenetetramine-N)bis(isothiocyanato)cobalt(Ⅱ) trans-tetraaquabis(isothiocyanato)cobalt(Ⅱ) dihydrate

1 INTRODUCTION Supramolecular compounds assembled by coordination covalent bonding or hydrogen bonding are of considerable interest due to their potential applications in developing new materials with magnetic, optical and catalytic properties[1]. One of the synthesis methods used to construct the functional compounds is that octahedral metal ion connects to polydentate ligand such as 4, 4?bipyridine, pyrazine and so on to form multi-dimensional supramolecular polymer[2]. Hmt (hexamethyl…     

X-ray structures of trans-dichloro(4-methylpyrimidine) (η1-phenyl)bis(pyridine)rhodium(III) hydrate and trans-dichloro(phenyl)tris(triphenylstibine)rhodium(III) ethylacetate solvate. Molecular orbital analysis of trans-dichloro (4-methylpyrimidine)(η1-phenyl)bis(pyridine)rhodium(III)

The crystal and molecular structure of trans-dichloro(4-methylpyrimidine)(η ¹ -phenyl)cis-bis(pyridine)rhodium(III) water solvate, 1x 0.17H₂ O, and trans-dichloro(η ¹ -phenyl)tris(triphenylstibine)rhodium(III) ethylacetate solvate, 2x CH₃ CO₂ CH₂ CH₃ have been studied via X-ray diffraction from a single crystal at room temperature. The final refinement converged to R1 conventional index of 0.0350 and 0.0361 for the structural analysis of 1x 0.17H₂ O [space group R(-3) and 2x CH₃ CO₂ CH₂ CH₃ P(-1) , respectively. The 4-methylpyrimidine ligand (Pym) is only weakly bound to Rh in 1, as shown by the long Rh-N distance (2.251(4) Å), compared to the Rh N(pyridine) lengths average, 2.066(4) . N-C bond distances involving the N donor average 1.329(6) and 1.345(6) for Pym and pyridine (Py) ligands, respectively. The C N C bond angle on the donor is 114.1(5)° for Pym and average 117.4(4)^° for Py.The structure of the complex molecule of 2x CH₃ CO₂ CH₂ CH₃ has some differences when compared to that of the corresponding acetone solvate previously studied in this laboratory (Cini, R., Giorgi, G. and Pasquini, L., Inor`. Chim. Acta, 1992, 196, 7). The two structures differ mainly by the orientation of the phenyl donor with respect to the Cl-Rh-Cl axis (which is more eclipsed for the ethylacetate solvate) and by the conformation of the SbPh₃ ligands.Density functional calculations at the B3LYP/LANL2DZ level with full geometry optimization were carried out on the free Pym molecule and on some Sc(N ¹ Pym) ^{3 +}and Sc(N ² Pym) ^{3 +} model molecules. The effect of metal coordination consists mainly in enlarging the (Sc)N-C bond distances up to 0.150Å, whereas the C-N(Sc)-C bond angle decreases of 1.9°. Significant changes on other bond lengths and angles relevant to ring atoms of Pym occur upon metal coordination to the nitrogen atom. The metal coordination to N(2) is less favorable than to N(1) of 7.5 kcal for 1:1 species of Sc^{3 +}Extended Hückel calculations showed that HOMO consists mostly of metal-d orbitals with some character of chloride and phenyl and pyrimidine ligands, whereas LUMO is composed of phenyl, pyridine and pyrimidine orbitals. The method well reproduces the Rh-N and Rh-C bonding distances and gives Rh-C dissociation energy 2.38 and 5.48 times that for the Rh-N(Py) and Rh-N(Pym) bonds, respectively.     

New access to (η(5)-cyclohexadienyl)Mn(CO)3 and cationic (η(6)-arene)Mn(CO)3 complexes by Suzuki-Miyaura reaction

First Suzuki-Miyaura coupling reactions applied to (η(5)-chloro-cyclohexadienyl)Mn(CO)3 complexes are described and lead to the syntheses of (η(5)-aryl-cyclohexadienyl)Mn(CO)3 and of cationic (η(6)-arene)Mn(CO)3 complexes after rearomatization. The structures of two of the new complexes have been investigated by X-ray diffraction study.     

Nd_2(Fe_(1-x)Co_x)_(14)B和Y_2(Fe_(1-x)Co_x)_(14)B的磁性

用磁测量和X-射线衍射研究了Nd_2(Fe_(1-x)Cox)_(14)B和Y_2(Fe_(1-x)Cox)_(14)B的晶格结构和内禀磁性。结果表明,低温下当钴含量较少时,Y_2(Fe_(1x)Cox)_(14)B的磁晶格向异性随钴含量的增加而增加,在1.5K和150K温度下,分别在x为0.4和0.2左右时磁晶各向异性常数达到极大;室温时的磁晶各向异性常数却随钴含量的增加而单调下降。用钴代换铁,对Nd_2(Fe_(1-x)Cox)_(14)B的自旋再取向温度的影响是复杂的。1.5K的饱和磁化强度在x=0.1左右达到极大。钴可以显著提高居里温度,对于Nd_2(Fe_(1-x)Cox)_(14)B和Y_2(Fe_(1-x)Cox)_(14)B,钴的作用几乎相同,表明居里温度主要由3d过渡金属原子之间的交换作用决定。     

~(13)C核磁共振(四)

9 ~(13)C自旋-晶格弛豫时间(T_1)的测量及应用 9.1 测定T_1的方法 9.1.1 倒向—恢复法此法是用(180°-τ-90°)_n脉冲系列作用于样品。磁化矢量M_0在180°脉冲作用下倒向(图20b),在自旋-晶格弛豫过程中,磁化矢量从-M_0经0到 M_0弛豫,在这一过程中,即过了时间τ后,90°脉冲将部份弛豫的磁化矢量M_τ旋转到X(?)Y平面中,并在接收线圈中感应出FID信号。如果τ很短,M_τ还是负的(M_τ<0),90°脉冲(?)_1,作用后M_τ沿X向负Y轴旋转(图20c),     

壳聚糖富集FAAS法测定水中痕量Cu（Ⅱ）

了以壳聚糖作富集柱，稀H2SO4为洗脱剂，稀NaOH为再生剂，火焰原子吸收光谱法简便，快速分离集测定水中痕量Cu(Ⅱ）的方法，于波长325nm处测定，检出限为为20ng.ml^0-1，线性范围为10－20μg.ml^-1。     

光度法测定保温材料中微量钛

研究了在氨性溶液中痕量Ti(Ⅳ )催化氯酸钾氧化靛红的褪色反应 ,催化程度与Ti(Ⅳ )呈线性关系。借此建立了测定痕量Ti(Ⅳ )的吸光光度法 ,其λmax=6 12nm ,检出限为 5.0× 10 - 12 g·ml- 1,Ti(Ⅳ )浓度在 0 .0～ 0 .5μg/ 50ml范围内服从比耳定律。结合伯胺N192 3萃取分离 ,可用于保温材料中微量钛的测定     

Ge（Ⅳ）—DB—o—NPF—CTMAB显色反应及其应用研究

在阳离子表面活性剂CTMAB存在下,研究了DB－o-NPF与GeⅣ的显色反应,试验表明,在磷酸介质中,Ge(Ⅳ）与DB-o-NPF形成1：2稳定的红色配合物,该配合物最大吸收波长为550nm,其表面摩尔吸光系数为1.04*10^5L.mol^-1.cm^-1,锗量在0－6ug/25ml范围内符合比耳定律,试验结果表明,Ge(Ⅳ)－DB－o-NPF-CTMAB体系显色测定Ge(IV),很多离子不干扰测定,方法灵敏度高,选择性好,有色配合物稳定48h以上,直接用于烟道灰中微量锗的测定,结果满意。     

Tb（Ⅲ）—ARS—CTMAB络合物的极谱吸附波研究

研究了在 p H9.4的氨 -氯化铵缓冲溶液中 ,Tb( )与茜素红 (ARS)、溴化十六烷基三甲铵 (CTMAB)三元络合物的极谱波 ,该极谱波峰电位在 - 0 .74V(vs.SCE) ,峰高与铽的浓度在6.0× 1 0 -8～ 8.0× 1 0 -6mol· L-1之间呈线性关系 ,检出限为 4.0× 1 0 -8mol· L-1,结合萃取柱色谱分离方法测定了稀土矿石中的重稀土元素铽。     

PHOTOLYSIS OF AQUEOUS SOLUTIONS OF POTASSIUM CIS-DIAQUOBIS (OXALATO) CHROMATE (III)

Abstract— The photolysis of aqueous solutions of cis -[Cr(C₂O₄)₂(H₂O)₂]- at 254 nm and pH 4 produced CO₂ and H₂ in nearly equal yields. The quantum yield of hydrogen, φ², increased by 9% and the yield of carbon dioxide, φ, by 65% as the pH was lowered from 4 to I. The total gas yield, φ_gas, decreased in the presence of added oxalate or chromium (II) ions and when the light intensity was lowered. The gas yield in D₂O was appreciably higher than in H₂O. The variation of φ_gas with pH (D) and with added oxalate ion was roughly parallel in the two liquid media. The gas yield increased in the series:
A tentative mechanism is suggested to explain the results.     

DBM—偶氮羧胂光度法测定微量锆

研究了DBM 偶氮羧胂与锆的显色反应体系 ,并应用于吸光光度法测定微量锆。DBM 偶氮羧胂与锆形成紫红色水溶性的络合物 ,最大吸收波长在 645nm。锆含量在 0 3 0 μg/2 5ml范围内符合比耳定律 ,表观摩尔吸光系数为 3 .4× 10 4 L·mol- 1·cm- 1,络合物的络合比为 1∶2。DBM 偶氮羧胂与锆的显色反应体系的稳定性及重现性较好 ,有较好的选择性。直接用于实际样品的测定 ,结果较好。     

Pb（Ⅱ）—双硫腙—PAR水相光度法测定样品中铅

研究了Pb(Ⅱ ) 双硫腙 (H2 Dz) PAR三元配合物显色体系 ,该体系最大优点是可在水相中直接用光度法测定样品中铅含量。配合物最大吸收波长为 530nm ,ε530 =2 .2× 10 4 L·mol- 1·cm- 1,Pb2 +浓度在 0～ 4 .75μg·ml- 1范围内符合比耳定律 ,经测定Pb(Ⅱ )∶H2 D2 ∶PAR =1∶1∶1。以邻二氮菲、硫脲 ,NH4 SCN溶液为掩蔽剂可消除常见元素干扰。此方法显色迅速、稳定 ,操作简便 ,避免了使用氰化钾剧毒试剂 ,以及萃取等烦琐操作 ,方法灵敏、准确 ,用于测定树叶和化妆品中铅含量 ,结果满意     

重油掺水乳化分散度的研究

70年代以来人们研究和开发了油掺水乳化燃烧的新技术 ,包括油水乳化方法和高效表面活性剂的研制[1～ 3] ,并在燃油设备上使用了这一技术。此外 ,国内外学者对重油掺水燃烧技术的燃烧机理进行了较多的研究[4 ,5] ,对乳化重油分散体系性质系统实验研究较少。工业炉窑燃用掺水乳化重油效果的好坏 ,除了与其粘度、稳定性有关外[6,7] ,与乳化重油的分散相(水 )微粒大小也有很大关系。水在油中分散得越均匀 ,分散的颗粒越微细 ,其在燃烧过程中的“微爆”效果则越佳 ,雾化效果越好 ;并且 ,分散体系中分散相颗粒粒径与比表面积的大小也决定着分散相…