Entropic death of nonpatterned and nanopatterned polyelectrolyte brushes

The stability of nonpatterned and nanopatterned strong polyelectrolyte brushes (PEBs) is studied as a function of both brush character and the properties of a contacting liquid. High‐molecular‐weight PEBs of poly(4‐methyl vinylpyridinium iodide) (PMeVP) are synthesized using surface‐initiated radical‐chain polymerization. Nanopatterned brushes (NPBs) line with pattern sizes ranging from 50 to 200 nm are generated by patterning the initiator layer using deep‐ultraviolet photolithography followed by brush growth initiated from the patterned layer. Homogeneous PEBs with different degrees of charging and grafting densities are exposed to water and salt solutions with different temperatures for different periods. The degradation is monitored through dry‐state ellipsometry and atomic force microscopy measurements. Enhanced degrafting for more strongly swollen polymer brushes can be observed in agreement with an “entropic spring” model. Based on the results of the nonpatterned brushes, the NPBs are exposed to water at different temperatures and external salt content for varying periods of time. Counterintuitively, the NPBs show increased degrafting for smaller patterns, which is attributed to different polymer chain dynamics for nanobrushes and microbrushes. We investigate the influence of thermodynamic and kinetic parameters on the stability of (nanopatterned) PEBs and discuss the role of entanglements and formation of complexes in such films. © 2019 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2019, 57, 1283–1295     

Micromechanical cantilever technique: a tool for investigating the swelling of polymer brushes

Polymer brush coatings are well-known for their ability to tailor surface properties in a wide range of applications from colloid stabilization to medicine. In most cases, the brushes are used in solution. Consequently, efforts were expended to experimentally investigate or theoretically predict the swelling behavior of the brushes in solvents of different qualities. Here, we show that the micromechanical cantilever (MC) sensor technique is a tool to perform time-resolved physicochemical investigations of thin layers such as polymer brushes. Complementary to scattering techniques, which measure the thickness, the MC sensor technique provides information about changes in the internal pressure of the brushes during a swelling and deswelling process. We show that the kinetics of both swelling and deswelling are dependent on solvent quality. Comparing the measured data with its thickness evolution, which was calculated based on the Flory-Huggins theory, we found that only the first 10% of the thickness increase of the polymer brush results in a significant pressure increase inside the polymer brush layer.     

Amphiphilic polymer brush in a mixture of incompatible liquids

An analogue of the Alexander‐DeGennes box model is used for theoretical investigation of polymer brushes in a mixture of two solvents. The basic solvent A and the admixture B are assumed to be highly incompatible (Flory‐Huggins parameter χ_AB = 3.5). Thermodynamics of a polymer in the solvents A and B are described by parameters χ_B < χ_A ≤ 1/2. The equilibrium behavior of a brush is investigated in dependence on solvent composition, grafting density, polymer‐solvents and solvent‐solvent interactions. The possibility of a phase transition related with a strong preferential solvation of a brush by a minor solvent component with higher affinity to polymer is shown and examined. Microphase segregation inside a brush is also demonstrated despite overestimating of the brush homogeneity given by the box model. A further simplification of the model permits to obtain scaling formulas and to investigate main regularities in the brush behavior. This offers a clear physical picture of the phase segregation inside a brush in correlation with the phase state of a bulk solvent.     

Synthesis and swelling behavior of pH-responsive polybase brushes

We synthesize polybase brushes and investigate their swelling behavior. Poly(2-(dimethylamino)ethyl methacrylate)) (PDMAEMA) brushes are prepared by the "grafting from" method using surface-initiated Atom Transfer Radical Polymerization to obtain dense brushes with relatively monodisperse chains (PDI = 1.35). In situ quaternization reaction can be performed to obtain poly(2-(trimethylamino)ethyl methacrylate)) (PTMAEMA) brushes. We determine the swollen thickness of the brushes using ellipsometry and neutron reflectivity techniques. Brushes are submitted to different solvent conditions to be investigated as neutral brushes and weak and strong polyelectrolyte brushes. The swelling of the brushes is systematically compared to scaling models. It should be pointed out that the scaling analysis of different types of brushes (neutral polymer and weak and strong polyelectrolyte brushes) is performed with identical samples. The scaling behavior of the PDMAEMA brush in methanol and the PTMAEMA brush in water is in good agreement with the predicted scaling laws for a neutral polymer brush in a good solvent and a polyelectrolyte brush in the osmotic regime. The salt-induced contraction of the quaternized brush is observed for high salt concentration, in agreement with the predicted transition between the regimes of the osmotic brush and the salted brush. From the crossover concentration, we calculate the effective charge ratio of the brush following the Manning counterion condensation. We also use PDMAEMA brushes as pH-responsive polybase brushes. The swelling behavior of the polybase brush is intermediate with respect to the behavior of the neutral polymer brush in a good solvent and the behavior of the quenched polyelectrolyte brush, as expected. The effective charge ratio of the PDMAEMA brush is determined as a function of pH using the scaling law of the polyelectrolyte brush in the osmotic regime.     

Volatile Organic Compound Sensing by Quartz Crystal Microbalances Coated with Nanostructured Macromolecular Metal Complexes

We report the construction of a molecular recognition layer composed of polyelectrolyte brushes and metal complexes on the surface of a quartz crystal microbalance (QCM) and the sensing abilities for various volatile organic compounds (VOCs). Atom‐transfer radical polymerization of 2‐(dimethylamino)ethyl acrylate from an initiator‐terminated self‐assembled monolayer yielded polyelectrolyte brushes on the surface of a weight‐detectable quartz crystal microbalance. One end of a poly[(2‐dimethylamino)ethyl methacrylate] brush was covalently attached onto the surface of a sensor. We found that metallophthalocyanines with four bulky pentaphenylbenzene substituents could adsorb volatile organic compounds selectively into their cavities. Macromolecular metal complexes were prepared by immersing polymer‐brush‐modified QCMs into an aqueous solution of sterically protected cobalt phthalocyanine. Anionic cobalt phthalocyanine was trapped in the polymer brushes and acted as a molecular receptor for the sensing of VOC molecules.     

Structure and Surface Properties of High-density Polyelectrolyte Brushes at the Interface of Aqueous Solution

Zwitterionic and cationic polyelectrolyte brushes were prepared by surface-initiated atom transfer radical polymerization of 2-methacryloyloxy- ethyl phosphorylcholine (MPC) and 2-(N,N-dimethylamino)ethyl methacrylate (DMAEMA), respectively. The poly(DMAEMA) brush was treated with methyl iodide to form poly[2-(methacryloyloxy) ethyltrimethylammonium iodide] [poly(METAI)]. The effects of ionic strength on brush structure and surface properties of densely grafted polyelectrolyte brushes were analyzed by contact angle measurements, neutron reflectivity (NR) and macroscopic friction tests. Both polyelectrolyte brushes exhibited hydrophilic properties. The contact angle of the poly(MPC) brush surface against water was ca. 0° in air and the contact angle of the air bubble in water was ca. 170°. The air bubble in water hardly attached to the poly(MPC) brush surface, indicating super hydrophilic characteristics. NR measurements of poly(MPC) and poly(METAI) brushes showed that the grafted polymer chains were extended from the substrate surface in a good solvent such as water. Interestingly, NR study did not reveal the shrinkage of the brush chain in salt solution. The polyelectrolyte brushes immersed in both water and NaCl solution at various concentrations showed a low friction coefficient and low adhesion force.     

Solid‐supported amphiphilic triblock copolymer membranes grafted from gold surface

Gold‐supported amphiphilic triblock copolymer brushes composed of two hydrophilic poly(2‐hydroxyethyl methacrylate) (PHEMA) blocks and a hydrophobic poly(n‐butyl methacrylate) (PBMA) middle part were synthesized using a surface‐initiated ATRP. Attenuated total reflectance Fourier transform infrared spectroscopy, polarization modulation infrared reflection absorption spectroscopy (PM‐IRRAS), ellipsometry, contact angle measurements, and atomic force microscopy were used for the characterization of PHEMA‐co‐PBMA‐co‐PHEMA brushes. The PM‐IRRAS analysis revealed an increase of the chain tilt toward the gold surface during growth of the individual blocks. We suggest that the orientation of the amphiphilic polymer brushes is influenced by both the chain length and the interchain interactions. Additionally, a detachment of the polymer membranes from the solid support and subsequent gel permeation chromatography analyses allowed us to establish their compositions. We applied block‐selective solvents (water and hexane) as well as a good solvent for the whole polymer chain (ethanol) to study the morphology and solvent responsive behavior of the amphiphilic brushes. The presented results could serve as a good starting point for the fabrication of functional solid‐supported membranes for biosensing applications. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 1–13, 2009     

Solvent dependent friction force response of polystyrene brushes prepared by surface initiated polymerization

Polystyrene (PS) brushes were prepared on oxide passivated silicon by the surface initiated polymerization (SIP) technique. From an AIBN-type free radical initiator, which was silanized and immobilized on silicon wafers, styrene brushes were directly polymerized and grafted from the surface. The formation of the initiator monolayer and, subsequently, the polymer brush on the surface were monitored by X-ray photoelectron spectroscopy (XPS) and ellipsometry. Friction force measurements were performed by atomic force microscopy (AFM), using a 5 microm SiO2 colloidal sphere tip and under systematically varied solvent environments (nonpolar to polar), to demonstrate the dependence of brush lubricity on solvation. The relative uptake of solvents in the PS brush was determined by quartz crystal microbalance (QCM), and it correlates well with friction data. It is surmised that, in poor solvent environments, the polymer brush exists in a collapsed conformation, giving rise to the higher observed friction response.     

pH‐Responsive Supramolecular Polymerization in Aqueous Media Driven by Electrostatic Attraction‐Enhanced Crown Ether‐Based Molecular Recognition

All the previously reported supramolecular polymers based on crown ether‐based molecular recognition have been prepared in anhydrous organic solvents. This is mainly due to the weakness of crown ether‐based molecular recognition in the presence of water. Here we report a linear supramolecular polymer constructed from a heteroditopic monomer in an aqueous medium driven by crown ether‐based molecular recognition through the introduction of electrostatic attraction. In addition, the reversible transition between the linear supramolecular polymer and oligomers is achieved by adding acid and base. This study realizes the breakthrough of the solvent for supramolecular polymerization driven by crown ether‐based molecular recognition from anhydrous organic solvents to aqueous media. It is helpful for achieving supramolecular polymerization driven by crown ether‐based molecular recognition in a completely aqueous medium.     

Water Content of Hydrated Polymer Brushes Measured by an In Situ Combination of a Quartz Crystal Microbalance with Dissipation Monitoring and Spectroscopic Ellipsometry

Poly(methacryloyloxy ethyltrimethylammonium chloride) (PMETAC), poly(sulfopropylmethacrylate potassium salt), or poly(N‐isopropyl acrylamide) (PNIPAM) brushes are synthesized by means of the atom transfer radical polymerization technique from gold surfaces coated with a monolayer of the initiator ω‐mercaptoundecyl bromo isobutyrate. The brush growth is followed in situ and in real time by the combination of quartz crystal microbalance with dissipation technique (QCM‐D) and spectroscopic ellipsometry in a single device. The combination of QCM‐D and ellipsometry allows for the simultaneous determination of both the acoustic mass, m_acous, comprising the mass of the polymer and the solvent, and the optical mass, m_opt, which corresponds to the polymer mass alone. Brush hydration is calculated from the difference between the values obtained for m_acous and m_opt for each polymer synthesized. Brush hydration is then used to quantify the percentage of water released in the brush during collapse; a 30–40% release of water for PMETAC and PSPM brushes in 1 M NaCl and 80% for PNIPAM brushes when the temperature is increased to values above the lower critical solution temperature is observed.     

Homopolymer and block copolymer brushes on gold by living anionic surface‐initiated polymerization in a polar solvent

Living anionic surface‐initiated polymerization on flat gold substrates has been conducted to create uniform homopolymer and diblock copolymer brushes. A 1,1‐diphenylethylene (DPE) self‐assembled monolayer was used as the immobilized precursor initiator. n‐BuLi was used to activate the DPE in tetrahydrofuran at –78 °C to initiate the polymerization of different monomers (styrene, isoprene, ethylene oxide, and methyl methacrylate). Poly(styrene) (PS) and poly(ethylene oxide) (PEO) in particular were first investigated as grafted homopolymers, followed by their copolymers, including poly(isoprene)‐b‐poly(methylmethacrylate) (PI‐b‐PMMA). A combined approach of spectroscopic (Fourier transform infrared spectroscopy, surface plasmon spectroscopy, ellipsometry, X‐ray photoelectron spectroscopy) and microscopic (atomic force microscopy) surface analysis was used to investigate the formation of the polymer brushes in polar solvent media. The chemical nature of the outermost layer of these brushes was studied by water contact angle measurements. The effect of the experimental conditions (solvent, temperature, initiator concentration) on the surface properties of the polymer brushes was also investigated. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 769–782, 2006     

Environment‐Adopting Surfaces with Reversibly Switchable Morphology

Two‐component polymer brushes (polystyrene and poly(2‐vinylpyridine)) were synthesized by grafting from the surface of Si‐wafers. The brushes are sensitive to the surrounding medium, and their morphology and composition of the top of a brush can be switched upon exposure to different solvents. Thus surface energetic states and roughness of the film can be precisely tuned.     

Tribological properties of hydrophilic polymer brushes under wet conditions

This article demonstrates a water‐lubrication system using high‐density hydrophilic polymer brushes consisting of 2,3‐dehydroxypropyl methacrylate (DHMA), vinyl alcohol, oligo(ethylene glycol)methyl ether methacrylate, 2‐(methacryloyloxy)ethyltrimethylammonium chloride (MTAC), 3‐sulfopropyl methacrylate potassium salt (SPMK), and 2‐methacryloyloxyethyl phosphorylcholine (MPC) prepared by surface‐initiated controlled radical polymerization. Macroscopic frictional properties of brush surfaces were characterized by sliding a glass ball probe in water using a ball‐on‐plate type tribotester under the load of 0.1–0.49 N at the sliding velocity of 10^?5–10^?1 m s^?1 at 298 K. A poly(DHMA) brush showed a relatively larger friction coefficient in water, whereas the polyelectrolyte brushes, such as poly(SPMK) and poly(MPC), revealed significantly low friction coefficients below 0.02 in water and in humid air conditions. A drastic reduction in the friction coefficient of polyelectrolyte brushes in aqueous solution was observed at around 10^?3–10^?2 m s^?1 owing to the hydrodynamic lubrication effect, however, an increase in salt concentration in the aqueous solution led to the increase in the friction coefficients of poly(MTAC) and poly(SPMK) brushes. The poly(SPMK) brush showed a stable and low friction coefficient in water even after sliding over 450 friction cycles, indicating a good wear resistance of the brush film. © 2010 The Japan Chemical Journal Forum and Wiley Periodicals, Inc. Chem Rec 10: 208–216; 2010: Published online in Wiley InterScience ( www.interscience.wiley.com ) DOI 10.1002/tcr.201000001     

Internal Architecture of Zwitterionic Polymer Brushes Regulates Nonfouling Properties

In this work, we study how film thickness and chain packing density affect the protein‐resistant properties of polymer brushes in complex media. Polymer brushes based on dual‐functional poly(carboxybetaine acrylamide) (pCB) were prepared via surface‐initiated photoiniferter‐mediated polymerization. By adjusting UV radiation time and solvent polarity, pCB films with different thicknesses can be achieved and characterized using an ellipsometer. The packing density of pCB polymer chains is directly related to the swelling ratio of swollen to collapsed film thicknesses. Results showed that the dry film thickness alone, used often in the literature, is not sufficient to correlate with nonfouling properties and the chain packing density must be considered for the design of nonfouling surface coatings.     

Functionalization and patterning of reactive polymer brushes based on surface reversible addition and fragmentation chain transfer polymerization

We present the synthesis of reactive polymer brushes prepared by surface reversible addition–fragmentation chain transfer polymerization of pentafluorophenyl acrylate. The reactive ester moieties can be used to functionalize the polymer brush film with virtually any functionality by simple post‐polymerization modification with amines. Dithiobenzoic acid benzyl‐(4‐ethyltrimethoxylsilyl) ester was used as the surface chain transfer agent (S‐CTA) and the anchoring group onto the silicon substrates. Reactive polymer brushes with adjustable molecular weight, high grafting density, and conformal coverage through the grafting‐from approach were obtained. Subsequently, the reactive polymer brushes were converted with amino‐spiropyrans resulting in reversible light‐responsive polymer brush films. The wetting behavior could be altered by irradiation with ultraviolet (UV) or visible light. Furthermore, a patterned surface of polymer brushes was obtained using a lithography technique. UV irradiation of the S‐CTA‐modified substrates leads to a selective degradation of S‐CTA in the exposed areas and gives patterned activated polymer brushes after a subsequent RAFT polymerization step. Conversion of the patterned polymer brushes with 5‐((2‐aminoethyl)amino)naphthalene‐1‐sulfonic acid resulted in patterned fluorescent polymer brush films. The utilization of reactive polymer brushes offers an easy approach in the fabrication of highly functional brushes, even for functionalities whose introduction is limited by other strategies. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Microphase coexistence in polymeric brushes

A collapse of polymeric brushes in a solvent can be induced by a change in external conditions, for example, solvent quality or its temperature. The systems with following specific interactions are considered in this paper, namely, polyelectrolyte brushes, amphiphilic brushes in a mixture of incompatible solvents, and brushes with possibility of liquid-crystalline ordering of polymer segments. For all the systems it is shown that the brush collapse can be observed under certain conditions, and it occurs through a microphase segregation. There are two microphases of different densities that coexist in the brush. The effect is caused by general properties of the swollen phase of polymeric brush and hence appears at all types of the interactions that can induce a phase transition of the brush into collapsed state.     

Stimuli‐responsive diblock copolymer brushes via combination of “click chemistry” and living radical polymerization

pH‐ and temperature‐responsive poly(N‐isopropylacrylamide‐block?4‐vinylbenzoic acid) (poly(NIPAAm‐b‐VBA)) diblock copolymer brushes on silicon wafers have been successfully prepared by combining click reaction, single‐electron transfer‐living radical polymerization (SET‐LRP), and reversible addition‐fragmentation chain‐transfer (RAFT) polymerization. Azide‐terminated poly(NIPAAm) brushes were obtained by SET‐LRP followed by reaction with sodium azide. A click reaction was utilized to exchange the azide end group of a poly(NIPAAm) brushes to form a surface‐immobilized macro‐RAFT agent, which was successfully chain extended via RAFT polymerization to produce poly(NIPAAm‐b‐VBA) brushes. The addition of sacrificial initiator and/or chain‐transfer agent permitted the formation of well‐defined diblock copolymer brushes and free polymer chains in solution. The free polymer chains were isolated and used to estimate the molecular weights and polydispersity index of chains attached to the surface. Ellipsometry, contact angle measurements, grazing angle‐Fourier transform infrared spectroscopy, and X‐ray photoelectron spectroscopy were used to characterize the immobilization of initiator on the silicon wafer, poly(NIPAAm) brush formation via SET‐LRP, click reaction, and poly(NIPAAm‐b‐VBA) brush formation via RAFT polymerization. The poly(NIPAAm‐b‐VBA) brushes demonstrate stimuli‐responsive behavior with respect to pH and temperature. The swollen brush thickness of poly(NIPAAm‐b‐VBA) brush increases with increasing pH, and decreases with increasing temperature. These results can provide guidance for the design of smart materials based on copolymer brushes. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013, 51, 2677–2685     

Nanosegregated polymeric domains on the surface of Fe3O4@SiO2 particles

Multifunctional, biocompatible, and brush‐grafted poly(ethylene glycol)/poly(ε‐caprolactone) (PEG/PCL) nanoparticles have been synthesized, characterized, and used as vehicles for transporting hydrophobic substances in water. For anchoring the polymer mixed brushes, we used magnetic‐silica particles of 40 nm diameter produced by the reverse microemulsion method. The surface of the silica particle was functionalized with biocompatible polymer brushes, which were synthesized by the combination of “grafting to” and “grafting from” techniques. PEG was immobilized on the particles surface, by “grafting to,” whereas PCL was growth by ROP using the “grafting from” approach. By varying the synthetic conditions, it was possible to control the amount of PCL anchored on the surface of the nanoparticles and consequently the PEG/PCL ratio, which is a vital parameter connected with the arrangement of the polymer brushes as well as the hydrophobic/hydrophilic balance of the particles. Thus, adjusting the PEG/PCL ratio, it was possible to obtain a system formed by PEG and PCL chains grafted on the particle's surface that collapsed in segregated domains depending on the solvent used. For instance, the nanoparticles are colloidally stable in water due to the PEG domains and at the same time are able to transport, entrapped within the PCL portion, highly water‐insoluble drugs. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2966–2975     

Adhesion between chemically heterogeneous switchable polymeric brushes and an elastomeric adhesive

We investigated the adhesive properties of binary heterogeneous polymer brushes made from end-functionalized polystyrene (PS) and poly(2-vinylpyridine) (P2VP) chains. The molecular organization of the mixed brush could be varied reversibly by exposure to selective solvents for PS (toluene) and for P2VP (acidic water). This exposure results in reversible switching of adhesive and wetting properties. The manner in which the adhesion switching occurs can be tuned by the composition of mixed brushes. However, the outer surface composition could be enriched more effectively in PS after the toluene treatment than in P2VP after the acidic water treatment. As a result, the mixed brush compositions that showed the largest difference in properties between an exposure to toluene and an exposure to water were the P2VP-rich compositions. Adhesive properties, tested against a soft hydrophobic pressure-sensitive adhesive (PSA) using a probe test, always showed smaller differences between solvent treatments than wetting properties with water, suggesting a much higher sensitivity of the hydrophobic/hydrophilic brushes to polar molecules than to nonpolar molecules.     

Stratified Polymer Brushes from Microcontact Printing of Polydopamine Initiator on Polymer Brush Surfaces

Stratified polymer brushes are fabricated using microcontact printing (μCP) of initiator integrated polydopamine (PDOPBr) on polymer brush surfaces and the following surface initiated atom transfer radical polymerization (SI‐ATRP). It is found that the surface energy, chemically active groups, and the antifouling ability of the polymer brushes affect transfer efficiency and adhesive stability of the polydopamine film. The stickiness of the PDOPBr pattern on polymer brush surfaces is stable enough to perform continuous μCP and SI‐ATRP to prepare stratified polymer brushes with a 3D topography, which have broad applications in cell and protein patterning, biosensors, and hybrid surfaces.