Degradation of chlorophenols in aqueous solution by γ-radiation

Degradation of chlorophenols (CPs) in aqueous solutions by γ-radiation was studied. The effect of absorbed dose on degradation, dechlorination and mineralization of CPs were investigated. The results indicated that the degradation of CPs, Cl⁻ release and mineralization increased with increase in absorbed dose. When the initial concentration was 100 mg L⁻¹ and the dosage was 6 kGy, the removal efficiencies of CPs were 44.54% for 2-CP, 91.46% for 3-CP, 82.72% for 4-CP and 93.25% for 2,4-DCP, respectively. The combination of irradiation and H₂O₂ leads to a synergistic effect, which remarkably increased the degradation efficiency of CPs and TOC removal. The kinetics of CPs during irradiation are also mentioned.     

Photo-Fenton degradation of resorcinol mediated by catalysts based on iron species supported on polymers

Novel Fe supported catalysts were prepared by immobilizing iron species on commercial polyethylene via three different methods: (1) acidic pre-treatment of the polyethylene followed by impregnation in aqueous Fe(NO₃)₃, (2) TiO₂ photo-catalytic pre-treatment of the polyethylene followed by forced hydrolysis of Fe(NO₃)₃, and (3) direct photo-Fenton attack with concomitant iron deposition on the polyethylene surface. The last method required soft conditions and led to the most photo-active Fe–polyethylene film. With this material, at a non-adjusted initial pH of 5.6 in the presence of H₂O₂, total degradation and 50% of resorcinol mineralization were observed in 40 and 60 min, respectively. Photo-Fenton functionalization/Fe-deposition process was also applied to polypropylene, high-impact polystyrene, and polymethylmethacrylate films. The efficiencies of all the prepared heterogeneous photo-catalysts were similar to that of an homogeneous photo-Fenton system containing the same amount of Fe^3+/2+ that leached during “heterogeneous” processes. That demonstrated than in our systems mainly homogeneous photo-Fenton reactions were responsible for the resorcinol degradation. The photo-catalytic activity observed for the Fe/polymer was a function of the specific polymer capacity to release the initially deposited iron into the solution.     

High energy induced decoloration and mineralization of Reactive Red 120 dye in aqueous solution: A steady state and pulse radiolysis study

Gamma radiation induced decoloration and degradation of aqueous solution of Reactive Red 120 dye (RR-120) have been investigated under different experimental conditions. Rate constants for the reaction of hydrated electron and hydroxyl radical with RR-120 were determined to be 1.2×10¹⁰ and 7.9×10⁹ mol^?1 dm³ s^?1, respectively, by pulse radiolysis technique. The decoloration and degradation efficiency were measured in terms of % decoloration and % TOC, respectively. Decoloration was observed to be most efficient under reducing condition, where the radiolytic yield for the decoloration of dye was determined to be 0.14 μmol/J. The extent of decoloration for both aerated and oxygen saturated solution was almost identical, whereas it decreased in N₂O saturated solution as well as N₂ saturated solution. For a solution having 10.56 μg/ml total organic carbon (TOC) at a dose of 3 kGy, 48% mineralization takes place in oxygen saturated solution whereas under aerated condition same was observed to be lowered to 38%.     

Photobleaching and mineralization of Orange II by oxone and metal-ions involving Fenton-like chemistry under visible light

Cu²⁺ and Fe³⁺ significantly improved the Orange II photobleaching and mineralization in the presence of oxone. In the presence of Cu²⁺ and Fe³⁺ the oxone needed for the photobleaching and total mineralization of the dye was determined along other solution parameters. In air, the photobleaching of Orange II in solution was observed to be complete within 60 min for Cu²⁺-ions and 30 min for Fe³⁺-ions showing a considerable faster kinetics with respect to other treatment systems reported until now. The transition metal-ions used seem to couple with oxone forming high oxidizing sulfate species. A reaction mechanism leading to Orange II photobleaching is suggested through a complex formation between the metal-ion and Orange II involves redox reactions activated by visible light.     

Efficient passivation of SnO2 nano crystallites by Indoline D-149 via dual chelation

For the first time in SnO₂ based dye solar cells, here we report, efficiency exceeding 3% of the cells consisting with Indoline D-149 dye with unmodified SnO₂ nano-crystallites. The cells sensitized with metal free D-149 dye together with liquid electrolyte comprising with 0.5 M tetrapropyl ammonium iodide and 0.05 M iodine in a mixture of acetonitrile and ethylene carbonate (1:4 by volume) delivered a short circuit current density of 10.4 mA cm^?2 with an open circuit voltage of 530 mV under the illumination of 100 mW cm^?2 (AM1.5) having an efficiency of 3.1%. As evident from the FTIR measurement, strong surface passivation of recombination centers of SnO₂ crystallites due to the dual mode of attachment of dye molecules to the surface of SnO₂ via both COOH and S–O direct bond might be the possible reason for this enhancement in these SnO₂ based cells.     

Mössbauer spectroscopic study of photo-sensitive organic–inorganic hybrid system, (SP)[Fe(II)Fe(III)(dto)3](dto = C2O2S2, SP = spiropyran)

A photo-sensitive organic–inorganic hybrid system (SP)[Fe^IIFe^III(dto)₃] (SP = spiropyran, dto = C₂O₂S₂), has recently been developed, where the photo-isomerization of the intercalated spiropyran in solid state triggers the change of the magnetic properties, including the ferromagnetic transition temperature from 5 to 22 K. We performed ⁵⁷Fe Mössbauer measurement in order to probe the microscopic states of iron ions in (SP)[Fe^IIFe^III(dto)₃] and have investigated the photo-induced effect on them. The sample without UV-irradiation shows the charge transfer phase transition between 200 and 70 K and the higher and lower temperature phases coexist below 70 K, whereas the UV-irradiated sample does not undergo the charge transfer phase transition and the higher temperature phase is stable between 200 and 6 K.     

Mesoporous Fe2O3 nanoparticles as high performance anode materials for lithium-ion batteries

This work introduces an effective, inexpensive, and large-scale production approach to the synthesis of Fe₂O₃ nanoparticles with a favorable configuration that 5 nm iron oxide domains in diameter assembled into a mesoporous network. The phase structure, morphology, and pore nature were characterized systematically. When used as anode materials for lithium-ion batteries, the mesoporous Fe₂O₃ nanoparticles exhibit excellent cycling performance (1009 mA h g^− 1 at 100 mA g^− 1 up to 230 cycles) and rate capability (reversible charging capacity of 420 mA h g^− 1 at 1000 mA g^− 1 during 230 cycles). This research suggests that the mesoporous Fe₂O₃ nanoparticles could be suitable as a high rate performance anode material for lithium-ion batteries.     

Structures,thermal expansion properties and phase transitions of ErxFe2−x(MoO4)3 (0.0 ≤ x ≤ 2.0)

Structures, thermal expansion properties and phase transitions of Er_xFe_2−x(MoO₄)₃ (0.0 ≤ x ≤ 2.0) have been investigated by X-ray diffraction and differential thermal analysis. The partial substitution of Er³⁺ for Fe³⁺ induces pronounced decreases in the phase transition temperature from monoclinic to orthorhombic structure. Rietveld analysis of the XRD data shows that both the monoclinic and orthorhombic Fe₂(MoO₄)₃, as well as the orthorhombic Er_xFe_2−x(MoO₄)₃ (x ≤ 0.8) have positive thermal expansion coefficients. However, the linear thermal expansion coefficients of Er_xFe_2−x(MoO₄)₃ (x = 0.6–2.0) decrease with increasing content of Er³⁺ and for x ≥ 1.0, compounds Er_xFe_2−x(MoO₄)₃ show negative thermal expansion properties. Attempts for making zero thermal expansion coefficient materials result in that very low negative thermal expansion coefficient of −0.60 × 10⁻⁶/°C in Er_1.0Fe_1.0(MoO₄)₃ is observed in the temperature range of 180–400 °C, and zero thermal expansion is observed in Er_0.8Fe_1.2(MoO₄)₃ in the temperature range of 350–450 °C. In addition, anisotropic thermal expansions are found for all the orthorhombic Er_xFe_2−x(MoO₄)₃ compounds, with negative thermal expansion coefficients along the a axes.     

Magnetic dilution effect on the charge transfer phase transition and the ferromagnetic transition for an iron mixed-valence complex, (n-C3H7)4N[FeII1−xZnIIxFeIII(dto)3] (dto = C2O2S2)

Iron mixed-valence complex, (n-C₃H₇)₄N[Fe^IIFe^III(dto)₃] (dto = C₂O₂S₂) shows a new-type of phase transition coupled with spin and charge around 120 K, where the charge transfer between the Fe^II and Fe^III sites occurs reversibly, and shows the ferromagnetic transition at 7 K. To investigate the magnetic structure and its dimensionality of (n-C₃H₇)₄N[Fe^IIFe^III(dto)₃], we have synthesized a mixed crystal system, (n-C₃H₇)₄N[Fe^II_1?xZn^II_xFe^III(dto)₃], and measured its magnetic properties. In this system, the magnetic moment is reduced with increasing of Zn ratio. Moreover, the ferromagnetic interaction changes to the antiferromagnetic one and the remnant magnetization disappears between x = 0.48 and 0.96, while the charge transfer between the Fe^II and Fe^III sites disappears above x = 0.26. In this paper, we present the magnetic dilution effect on the charge transfer phase transition and the ferromagnetic transition by means of magnetic susceptibility measurement and ⁵⁷Fe Mössbauer spectroscopy.     

Influence of particle size on the photoactivity of Ti/TiO2 thin film electrodes,and enhanced photoelectrocatalytic degradation of indigo carmine dye

Photoanodes based on Ti/TiO₂ thin films were prepared by the sol–gel method, using either tetraisopropoxide (Ti(OPri)₄) or modified tetraisopropoxide, producing electrodes with different sized nanoparticle coatings, termed nanoporous (20 nm) or nanoparticulated (10 nm) electrodes. The anatase form dominated the composition of the nanoparticulated electrode, which presented a higher surface area, a flat band potential shift of ?160 mV and a 50% improvement in photoactivity, compared to the nanoporous electrode. 100% color removal, and 75% mineralization, of indigo carmine dye were achieved after 15 min of photoelectrocatalytic treatment using a nanoparticulated Ti/TiO₂ electrode operated at a current density of 0.4 mA cm^?2. Our findings indicate that the use of nanoparticulated electrodes, under UV irradiation and with controlled current density, is an efficient alternative for the removal of food dye contaminants during wastewater treatment.     

Redox behavior and transport properties of La0.5−2xCexSr0.5+xFeO3−δ and La0.5−2ySr0.5+2yFe1−yNbyO3−δ perovskites

The effects of doping the mixed-conducting (La,Sr)FeO_3−δ system with Ce and Nb have been examined for the solid-solution series, La_0.5−2xCe_xSr_0.5+xFeO_3−δ (x = 0–0.20) and La_0.5−2ySr_0.5+2yFe_1−yNb_yO_3−δ (y = 0.05–0.10). Mössbauer spectroscopy at 4.1 and 297 K showed that Ce⁴⁺ and Nb⁵⁺ incorporation suppresses delocalization of p-type electronic charge carriers, whilst oxygen nonstoichiometry of the Ce-containing materials increases. Similar behavior was observed for La_0.3Sr_0.7Fe_0.90Nb_0.10O_3−δ at 923–1223 K by coulometric titration and thermogravimetry. High-temperature transport properties were studied with Faradaic efficiency (FE), oxygen-permeation, thermopower and total-conductivity measurements in the oxygen partial pressure range 10⁻⁵–0.5 atm. The hole conductivity is lower for the Ce- and Nb-containing perovskites, primarily as a result of the lower Fe⁴⁺ concentration. Both dopants decrease oxide-ion conductivity but the effect of Nb-doping on ionic transport is moderate and ion-transference numbers are higher with respect to the Nb-free parent phase, 2.2 × 10⁻³ for La_0.3Sr_0.7Fe_0.9Nb_0.1O_3−δ cf. 1.3 × 10⁻³ for La_0.5Sr_0.5FeO_3−δ at 1223 K and atmospheric oxygen pressure. The average thermal expansion coefficients calculated from dilatometric data decrease on doping, varying in the range (19.0–21.2) × 10⁻⁶ K⁻¹ at 780–1080 K.     

Impact of Fe3+ on UV absorption of K2Al2B2O7 crystals

K₂Al₂B₂O₇ (KABO) is a new nonlinear optical crystal capable of laser harmonic generation in the UV range. However, abnormal UV absorption prevents its application in effectively generating UV light with wavelength shorter than 300 nm. The transmittance spectra of the grown crystals show distinct absorption bands at 216 nm and 264 nm. It is observed that the UV absorption is strongly correlated with iron impurity at a parts per million (ppm) level. Furthermore, electron paramagnetic resonance (EPR) spectra of the absorbing crystals show a strong signal at g = 2.00 position corresponding to a Fe³⁺ center. A new crystal growth method which reduces the iron content has been proposed and results show that the new KABO crystal is free from the Fe³⁺ UV absorptions.     

Stress-induced ligand field distribution and consequent multi-mode spin crossover in FeII(phen)2(NCS)2 and FeII[HB(pz)3]2

Changes in the nature of spin crossover caused by mechanical stressing exerted on the crystalline powders were studied for Fe^II(phen)₂(NCS)₂ (phen = 1,10-phenanthroline) and Fe^II[HB(pz)₃]₂ (pz = pyrazol-1-yl) by means of a multi-component fitting of the temperature dependence of magnetic susceptibility. The analysis revealed the development and broadening of the ligand field distribution as a consequence of mechanical stressing. This was confirmed by the broadening of Mössbauer and far-infrared spectra.     

Synthesis,physico-chemical and spectral investigations of novel homo-bimetallic mixed-ligand complexes: 57Fe Mössbauer parameters of [Fe2(imda)2(H2O)3Cl]

The newly prepared homo-bimetallic complexes [M₂(imda)₂(H₂O)₄], [M₂(imda)₂(Bipy)₂] (M = Co, Ni or Cu) and [Fe₂(imda)₂(H₂O)₃Cl] (H₂imda = iminodiacetic acid and Bipy = 2,2′-bipyridine) have been studied employing IR, FAB-mass, ¹H and ¹³C NMR, EPR and ligand field spectra, which indicated a high-spin state of metal ion with hexa-coordinate environment. ⁵⁷Fe Mössbauer data of the homo-bimetallic complex [Fe₂(imda)₂(H₂O)₃Cl] confirm a high-spin configuration with Fe (±3/2 → 1/2) nuclear transitions and the presence of Kramer's double degeneracy. At RT, the spin–spin interactions of the neighbouring nuclei (Fe³⁺–Fe³⁺ = S_5/2–S_5/2) are anti-ferromagnetically coupled. However, at LNT, the complex acquires a mixed-valent [Fe^III–Fe^II] composition corroborated from the X-band EPR data. CV studies indicated the presence of quasi-reversible redox Cu^II/I, Cu^II/III, Fe^III/II, Fe^III/I and Fe^II/I couples.     

Effective scrap iron particles (SIP) pre-treatment for complete mineralization of benzidine based azo dye effluent

This study proposed that hybrid scrap cast iron particles (SIP)-aerobic biodegradation technology could enhance the biodegradability of toxic wastewater. SIP cleaved the azo linkages of Direct Green1 dye to form benzidine, 4-aminophenol, aniline and 1,2,7-triamino-8-hydroxynapthalene-3,6-disulfonic acid. SIP-mediated dye reduction was effective at wide pH range; however, kinetic analysis revealed fastest pseudo-first order dye reduction rate at acidic pH 3 (k_d = 0.549 min⁻¹) followed by pH 9 (k_d = 0.383 min⁻¹) and pH 7 (k_d = 0.318 min⁻¹). The daughter aromatic amines produced were partially adsorbed onto the SIP surface and maximally at neutral pH. The adsorption process followed pseudo-second order adsorption kinetics and Langmuir isotherm. Benzidine was adsorbed more than 4-aminophenol and aniline. BOD₅ of the SIP-treated effluent increased from 0.93 to 12 mg/L showing improved biodegradability. The daughter amines were rapidly mineralized in the aerobic bioreactor within 6 h. Cost-effective SIP pre-treatment could accelerate mineralization and detoxification of recalcitrant wastewater.     

Photocatalytic activity of nitrogen and copper doped TiO2 nanoparticles prepared by microwave-assisted sol-gel process

Cu and N-doped TiO₂ photocatalysts were synthesized from titanium (IV) isopropoxide via a microwave-assisted sol-gel method. The synthesized materials were characterized by X-ray diffraction, UV-vis diffuse reflectance, photoluminescence (PL) spectroscopy, SEM, TEM, FT-IR, Raman spectroscopy, photocurrent measurement technique, and nitrogen adsorption–desorption isotherms. Raman spectra and XRD showed an anatase phase structure. The SEM and TEM images revealed the formation of an almost spheroid mono disperse TiO₂ with particle sizes in the range of 9-17 nm. Analysis of N₂ isotherm measurements showed that all investigated TiO₂ samples have mesoporous structures with high surface areas. The optical absorption edge for the doped TiO₂ was significantly shifted to the visible light region. The photocurrent and photocatalytic activity of pure and doped TiO₂ were evaluated with the degradation of methyl orange (MO) and methylene blue (MB) solution under both UV and visible light illumination. The doped TiO₂ nanoparticles exhibit higher catalytic activity under each of visible light and UV irradiation in contrast to pure TiO₂. The photocatalytic activity and photocurrent ability of TiO₂ have been enhanced by doping of the titania in the following order: (Cu, N) - codoped TiO₂ > N-doped TiO₂ > Cu-doped TiO₂ > TiO₂. COD result for (Cu, N)-codoped TiO₂ reveals ∼92% mineralization of the MO dye on six h of visible light irradiation.     

An enzymatic glucose/O2 biofuel cell: Preparation,characterization and performance in serum

This study demonstrates a new kind of single-walled carbon nanotubes (SWNT)-based compartment-less glucose/O₂ biofuel cell (BFC) with glucose dehydrogenase (GDH) and bilirubin oxidase (BOD) as the anodic and cathodic biocatalysts, respectively, and with poly(brilliant creysl blue) (BCB) adsorbed onto SWNT nanocomposite as the electrocatalyst for the oxidation of NADH. The prepared GDH-polyBCB-SWNT bioanode exhibits an excellent electrocatalytic activity toward the oxidation of glucose biofuel; in 0.10 M phosphate buffer containing 20 mM NAD⁺ and 100 mM glucose, the oxidation of glucose commences at −0.25 V and the current reaches its maximum of 310 μA/cm² at −0.05 V vs. Ag/AgCl. At the BOD-SWNT biocathode, a high potential output is achieved for the reduction of O₂ due to the direct electron transfer property of BOD at the SWNTs. In 0.10 M phosphate buffer, the electrocatalytic reduction of O₂ is observed at a high potential of 0.53 V vs. Ag/AgCl with an electrocatalytic current plateau of ca. 28 μA/cm² at 0.45 V under ambient air and ca. 102 μA/cm² under O₂-saturated atmosphere. In 0.10 M phosphate buffer containing 10 mM NAD⁺ and 40 mM glucose under O₂-saturated atmosphere, the power density of the assembled SWNT-based glucose/O₂ BFC reaches 53.9 μW/cm² at 0.50 V. The performance and the stability of the glucose/O₂ BFC are also evaluated in serum. This study could offer a new route to the development of new kinds of enzymatic BFCs with a high performance and provide useful information on future studies on the enzymatic BFCs as in vivo power sources.     

Iron (III) nanocomposites for enzyme-less biomimetic cathode: A promising material for use in biofuel cells

In this paper, we discuss the synthesis and electrochemical properties of a new material based on iron oxide nanoparticles stabilized with poly(diallyldimethylammonium chloride) (PDAC); this material can be used as a biomimetic cathode material for the reduction of H₂O₂ in biofuel cells. A metastable phase of iron oxide and iron hydroxide nanoparticles (PDAC–FeOOH/Fe₂O₃-NPs) was synthesized through a single procedure. On the basis of the Stokes–Einstein equation, colloidal particles (diameter: 20 nm) diffused at a considerably slow rate (D = 0.9 × 10^? 11 m s^? 1) as compared to conventional molecular redox systems. The quasi-reversible electrochemical process was attributed to the oxidation and reduction of Fe³⁺/Fe²⁺ from PDAC–FeOOH/Fe₂O₃-NPs; in a manner similar to redox enzymes, it acted as a pseudo-prosthetic group. Further, PDAC–FeOOH/Fe₂O₃-NPs was observed to have high electrocatalytic activity for H₂O₂ reduction along with a significant overpotential shift, ΔE = 0.68 V from ? 0.29 to 0.39 V, in the presence and absence of PDAC–FeOOH/Fe₂O₃-NPs. The abovementioned iron oxide nanoparticles are very promising as candidates for further research on biomimetic biofuel cells, suggesting two applications: the preparation of modified electrodes for direct use as cathodes and use as a supporting electrolyte together with H₂O₂.     

Study on the valence fluctuation and the magnetism of an iron mixed-valence complex, (n-C4H9)4N[FeIIFeIII(mto)3](mto = C2O3S)

In the case of iron mixed-valence complexes whose spin states are situated in the spin-crossover region, conjugated phenomena coupled with spin and charge are expected. In general, the Fe site coordinated by six S atoms is in the low-spin state, while the Fe site coordinated by six O atoms is in the high-spin state. From this viewpoint, we have synthesized and investigated physical properties for an monothiooxalato-bridged (mto = C₂O₃S) iron mixed-valence complex, (n-C₄H₉)₄N[Fe^IIFe^III(mto)₃], consisting of Fe^IIIO₃S₃ and Fe^IIO₆ octahedra, which behaves as a ferrimagnet with its magnetic transition temperature of T_N = 38 K and Weiss temperature of θ = ?93 K. From the analysis of ⁵⁷Fe Mössbauer spectra of ⁵⁷Fe enriched complexes, (n-C₄H₉)₄N[⁵⁷Fe^IIFe^III(mto)₃] and (n-C₄H₉)₄N[Fe^II57Fe^III(mto)₃], the charge transfer between Fe^II and Fe^III exists in the paramagnetic phase. Considering the time window of ⁵⁷Fe Mössbauer spectroscopy, the time scale of the valence fluctuation is at least slower than 10^?7 s. In order to confirm the valence fluctuation between Fe^II and Fe^III, we investigated the dielectric constant and found an anomalous enhancement attributed to the Fe valence fluctuation between 170 and 250 K.     

A comparative study for treatment of white liquor by different applications of Fenton process

In this paper, the treatability of white liquor by conventional (CFP), modified (MFP) and electro-Fenton oxidation processes (EFP) was investigated depending on the COD parameter. Based on the experimental results, up to 62.4%, 58.4% and 54.9% COD removals by the CFP, MFP and EFP were achieved, respectively. It was observed that adjustment of initial pH to acidic values is not required in the CFP. The optimal operational conditions were found to be [Fe²⁺] = 500 mg/L, [H₂O₂] = 1000 mg/L at pH 7.3 (original pH) in the CFP, [Fe⁰] = 1250 mg/L, [H₂O₂] = 1000 mg/L at pH 3 in the MFP, and I = 1.0 A, [H₂O₂] = 1500 mg/L at pH 3 in the EFP, respectively. As a result, the CFP has been determined as a more efficient alternative treatment method.