微波辅助萃取-气相色谱测定土壤中多氯联苯

建立了微波辅助萃取-气相色谱-微电子捕获检测土壤样品中6种多氯联苯(pcb28, pcb52, pcb101, pcb138, pcb153和pcb180)的方法. 确定了以V(20 mL丙酮):V(正己烷)＝1:1混合溶剂作萃取剂, 萃取温度110 ℃, 仪器功率800 W, 微波萃取5 min的样品前处理条件, 并用柱温程序优化了GC-μECD分析条件. 方法的检出限为0.027～0.087 ng/g; 相对标准偏差为3.4%～7.6% (n=6); 加标平均回收率79.8%～91.1%. 可用于土壤环境中多氯联苯的监测分析.     

金属-有机纳米管分散固相萃取-气相色谱-串联质谱高灵敏分析环境水样中痕量多氯联苯

采用含铅金属-有机纳米管为吸附剂,基于分散固相萃取和气相色谱-串联质谱建立了一种高灵敏分析环境水样中痕量多氯联苯的方法.采用正交设计响应面法对影响萃取效果的重要因素(如离子强度、萃取时间和吸附剂用量等)进行了优化.获得的最优条件为:离子强度4.92 %(w/V)NaCl,萃取时间4.5 min,正己烷为解吸剂,吸附剂用量62.5 mg.在优化条件下,方法的线性范围为2~1000 ng/L,检出限为0.26~0.82 ng/L. 日内和日间相对标准偏差分别为0.8%~5.5% (200 ng/L, n=6)和2.7%~7.4% (200 ng/L, n=6).将本方法应用于实际环境水样中多氯联苯的分析,回收率为78.9%~113.3%,结果满意.     

微波辅助-微固相在线萃取/气相色谱质谱联用法对污泥中19种多氯联苯的测定

建立了微波辅助-微固相在线萃取/气相色谱-质谱联用(GC-MS)测定污泥中19种多氯联苯(PCBs)含量的分析方法。对微波辅助-微固相在线萃取条件进行优化,得出最优萃取条件为:萃取温度60℃,萃取时间25 min,解吸溶剂为乙酸乙酯,解吸剂用量150μL,解吸时间25 min。在优化条件下,方法的检出限为0.2~2.5 ng/g,相对标准偏差(RSD)小于14%,回收率为81.4%~102.1%。与传统的微波萃取、微固相萃取、超声萃取等方法相比,该方法集萃取、净化和浓缩于一体,极大地缩短了分析时间,适合于复杂环境样品体系中痕量PCBs的分析检测。     

加速溶剂萃取-固相萃取净化-气相色谱/质谱法测定沉积物中多氯联苯和多环芳烃

建立了加速溶剂萃取-固相萃取净化-气相色谱/三重四极杆串联质谱联用(ASE-SPE-GC-QqQ-MS/MS)法同时测定沉积物中28种多氯联苯(PCBs)和16种多环芳烃(PAHs)。对萃取、净化及仪器分析条件进行了优化。优化条件为:ASE萃取温度90℃,萃取时间6 min;净化小柱为硅胶-Florisil固相复合柱(填料自下而上为弗罗里硅土、0.7 g活化硅胶、1 g无水硫酸钠);洗脱溶液为丙酮-正己烷(1∶19,V/V)混合溶液,洗脱速率为0.6 mL/min。PCBs和PAHs在2～500μg/L和5～1000μg/L浓度范围内的线性相关系数(R2)分别为0.9987～0.9999和0.9939～0.9999;PCBs和PAHs方法检出限分别为0.001～0.08 ng/g和0.07～0.45 ng/g;定量限为0.003～0.25 ng/g和0.24～1.67 ng/g;实际样品平均加标回收率为95.6%～125.7%和70.4%～124.7%;方法相对标准偏差(n=6)为0.7%～6.4%和1.1%～12.8%。运用本方法对滇池入湖河口表层沉积物样品进行测定,该区域PCBs单体浓度为n.d.(未检出)～0.13 ng/g,PAHs单体浓度为0.79～131.12 ng/g。     

气相色谱-质谱法同时测定地下水中42种半挥发性有机污染物

建立了同时测定地下水中多环芳烃(PAHs)、多氯联苯(PCBs)、有机氯农药(OCPs)和有机磷农药(OPPs)等42种半挥发性有机污染物的分析方法,对固相萃取、液-液萃取、萃取溶剂和色谱柱等分析条件进行优化。最终采用乙酸乙酯-正己烷(1∶4)液液萃取,DB-5MS色谱柱分离,GC-MS/SIM测定,内标法定量。结果表明,42种目标物在0.5~1 000μg/L范围内线性关系良好(r20.995);方法检出限为0.05~3.08 ng/L。在10、40、400 ng/L加标水平下,42种目标物的基体加标平均回收率为73.0%~107%,相对标准偏差(RSD,n=5)为1.4%~11.3%。将方法应用于石家庄周边地区水样检测,结果可靠。该方法灵敏、准确、简单易行,可显著提高地下水中主要有机污染物的分析效率。     

分散液液微萃取-气相色谱-串联质谱快速分析食用油中的酚类抗氧化剂

基于分散液液微萃取技术和气相色谱-串联质谱,建立了一种快速分析食用油中酚类抗氧化剂的新方法。对影响萃取效果的重要因素,如萃取剂种类及体积、分散剂种类及体积和萃取时间等进行了详细优化。优化条件为：500μL甲醇-乙腈(1：1, V/V)快速注射进3.0 mL 正己烷与1.0 g食用油的混合物中,并振荡萃取10 s 。在优化条件下,方法的线性范围为10~2000 ng/g,检出限为1.5~2.4 ng/g,相对标准偏差为4.0%~8.3%。将本方法应用于4种不同食用油样品的分析,其中3种有酚类抗氧化剂检出,样品加标回收率为81.9%~118%,结果满意。     

加速溶剂萃取-硅胶萃取净化-气相色谱/质谱法检测地表水中有机氯农药和多氯联苯

建立了加速溶剂萃取-硅胶固相萃取净化-气相色谱/质谱同时检测地表水中15种有机氯农药(OCPs)和82种多氯联苯(PCBs)的方法.对影响OCPs和PCBs回收率的主要因素进行优化,得出最优的萃取条件:3次静态萃取循环,100℃的萃取温度,丙酮/正己烷(1∶1,V/V)为萃取液,静态萃取10 min.在最优条件下,15种OCPs和82种PCBs在加标水溶液中的回收率分别为70.9％～130％和52.5％～89.1％.日内和日间相对标准偏差分别为1.7％～16.1％和2.4％ ～33.3％.OCPs和PCBs混合标样在10～ 800 μg/L范围内线性相关系数(R2)均大于0.995.OCPs和PCBs方法检测限分别为0.13 ～0.38 ng/L和0.10 ～0.32 ng/L.相比于传统萃取方法,本方法回收率高、萃取时间短、试剂用量少.应用本方法测得北京城区地表水中OCPs和PCBs的含量范围分别为n.d.～ 3.45 ng/L和n.d.～4.88 ng/L.     

固相微萃取-气质联用法快速筛查肝脏中常见投毒农药

基于溶剂提取-固相微萃取-气质联用技术建立了新鲜肝脏中26种常见投毒农药的快速筛查与定量方法。通过考察有机溶剂、萃取头、萃取温度等影响因素优化萃取条件;新鲜肝脏经丙酮水溶液提取,离心分离、氮吹浓缩后补充超纯水,经SPME萃取后采用GC-MS进行定性筛查与定量分析。实验结果表明,以丙酮水溶液(4:1,V/V)提取,选择PDMS/DVB/CAR萃取头,在pH 7.4缓冲溶液体系下、室温下(20℃)萃取30 min,搅拌速度为200 r/min时萃取效率最高;新鲜肝脏中26种农药在50~200 ng/g范围内具有良好的线性,相关系数均≥0.992,方法检出限(LOD)为0.15~16 ng/g(S/N=3),定量限(LOQ)为0.48~48 ng/g(S/N=10);在加入量为50,100,200 ng/g时,农药混合标准溶液的回收率为66.7%~108.2%,相对标准偏差为1.4%~16%。方法适用于对投毒案件受害者肝脏中常见投毒农药进行快速筛查与定量分析。     

土壤中10种多溴联苯醚的加速溶剂-固相萃取净化方法优化研究

建立了土壤中10种多溴联苯醚(PBDEs)的加速溶剂萃取-固相萃取净化-气相色谱分析测定方法.采用加速溶剂萃取(ASE)技术对土壤中10种PBDEs进行提取,并对4种萃取体系(正己烷、正己烷-丙酮(4∶1,V/V)、正己烷-丙酮(1∶1,V/V)、正己烷-二氯甲烷(1∶1,V/V))进行优化;采用固相萃取(SPE)技术对样品进行净化,制备了10种不同填料的SPE柱,通过洗脱实验和加标回收率实验对各SPE柱的净化性能进行对比筛选.最终优化条件为正己烷-丙酮(4∶1,V/V)体系提取,酸性硅胶柱净化.在优化条件下,10种PBDEs的回收率为74.4％ ～ 125.2％,相对标准偏差为4.4％ ～ 14.4％,方法检出限为0.04～0.22 ng/mL.本方法简单、快速、净化效果较好、重现性和回收率良好,可用于土壤样品中PBDEs的分析.     

微波萃取-全自动凝胶色谱净化-气相色谱法同时测定太湖沉积物中多氯联苯和有机氯

建立了沉积物中多氯联苯和有机氯农药等39种持久性有机污染物的同时测定方法。样品用正己烷和丙酮(体积比为1∶1)进行微波提取,提取溶液经凝胶色谱和弗罗里硅土净化,浓缩后采用气相色谱法测定。回收率在68.8%~84.2%,检出限为0.05~0.25ng/g。方法适用于沉积物样品中多种多氯联苯和有机氯农药含量的同时测定。     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Exploring the scope of the Gewald reaction: Expansion to a four-component process

An efficient four-component reaction was developed to take advantage of the reactivity of the 2-aminothiophene-3-carbonitrile functionality, which is obtained during the classical three-component Gewald reaction. Various α-methylene bearing ketones were reacted with malononitrile, elemental sulfur, and aryl/heteroarylnitrile derivatives in t-BuOH/NaOH to afford 2-arylthieno[2,3-d]pyrimidin-4-amines in high yields. Preliminary studies revealed the photophysical properties of the products and their potential for use as metal sensors.