Sorption and diffusion of methanol and water in PVDF‐g‐PSSA and Nafion® 117 polymer electrolyte membranes

Sorption and diffusion properties of poly(vinylidene fluoride)‐graft‐poly(styrene sulfonic acid) (PVDF‐g‐PSSA) and Nafion® 117 polymer electrolyte membranes were studied in water/methanol mixtures. The two types of membranes were found to have different sorption properties. The Nafion 117 membrane was found to have a maximum in‐solvent uptake around 0.4 to 0.6 mole fraction of methanol, while the PVDF‐g‐PSSA membranes took up less solvent with increasing methanol concentration. The proton NMR spectra were recorded for membranes immersed in deuterated water/methanol mixtures. The spectra showed that the hydroxyl protons inside the membrane exhibit resonance lines different from the resonance lines of hydroxyl protons in the external solvent. The spectral features of the lines of these internal hydroxyl groups in the membranes were different in the Nafion membrane compared with the PVDF‐g‐PSSA membranes. Diffusion measurements with the pulsed field gradient NMR (PFG‐NMR) method showed that the diffusion coefficient of the internal hydroxyl groups in the solvent immersed Nafion membrane mirrors the changes in the diffusion coefficients of hydroxyl and methyl protons in the external solvent. For the PVDF‐g‐PSSA membranes, a decrease in the diffusion coefficient of the internal hydroxyl protons was seen with increasing methanol concentration. These results indicate that the morphology and chemical structure of the membranes have an effect on their solvent sorption and diffusion characteristics. © 2000 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 38: 3277–3284, 2000     

Characterization and evaluation of commercial poly (vinylidene fluoride)‐g‐sulfonatedPolystyrene as proton exchange membrane

The possibility of developing low‐cost commercial grafted and sulfonated Poly(vinylidene fluoride) (PVDF‐g‐PSSA) membranes as proton exchange membranes for fuel cell applications have been investigated. PVDF‐g‐PSSA membranes were systematically prepared and examined with the focus of understanding how the polymer microstructure (degree of grafting and sulfonation, ion‐exchange capacity, etc) affects their methanol permeability, water uptake, and proton conductivity. Fourier transform infrared spectroscopy was used to characterize the changes of the membrane's microstructure after grafting and sulfonation. The results showed that the PVDF‐g‐PSSA membranes exhibited good thermal stability and lower methanol permeability. The proton conductivity of PVDF‐g‐PSSA membranes was also measured by the electrochemical impedance spectroscopy method. It was found that the proton conductivity of PVDF‐g‐PSSA membranes depends on the degree of sulfonation. All the sulfonated membranes show high proton conductivity at 92°C, in the range of 27 to 235 mScm⁻¹, which is much higher than that of Nafion212 (102 mScm⁻¹ at 80°C). The results indicated that the PVDF‐g‐PSSA membranes are particularly promising membranes to be used as polymer electrolyte membranes due to their excellent stability, low methanol permeability, and high proton conductivity.     

Proton conducting membranes based on poly(vinyl chloride) graft copolymer electrolytes

The direct preparation of proton conducting poly(vinyl chloride) (PVC) graft copolymer electrolyte membranes using atom transfer radical polymerization (ATRP) is demonstrated. Here, direct initiation of the secondary chlorines of PVC facilitates grafting of a sulfonated monomer. A series of proton conducting graft copolymer electrolyte membranes, i.e. poly(vinyl chloride)‐g‐poly(styrene sulfonic acid) (PVC‐g‐PSSA) were prepared by ATRP using direct initiation of the secondary chlorines of PVC. The successful syntheses of graft copolymers were confirmed by ¹H‐NMR and FT‐IR spectroscopy. The images of transmission electron microscopy (TEM) presented the well‐defined microphase‐separated structure of the graft copolymer electrolyte membranes. All the properties of ion exchange capacity (IEC), water uptake, and proton conductivity for the membranes continuously increased with increasing PSSA contents. The characterization of the membranes by thermal gravimetric analysis (TGA) also demonstrated their high thermal stability up to 200°C. The membranes were further crosslinked using UV irradiation after converting chlorine atoms to azide groups, as revealed by FT‐IR spectroscopy. After crosslinking, water uptake significantly decreased from 207% to 84% and the tensile strength increased from 45.2 to 71.5 MPa with a marginal change of proton conductivity from 0.093 to 0.083 S cm^?1, which indicates that the crosslinked PVC‐g‐PSSA membranes are promising candidates for proton conducting materials for fuel cell applications. Copyright © 2008 John Wiley & Sons, Ltd.     

Effects of graft length and density of well‐defined graft polymers on the thermoresponsive behavior and self‐assembly morphology

A series of well‐defined thermoresponsive graft polymers with different lengths and graft densities, poly(glycidyl methacrylate)‐graft‐poly(N‐isopropylacrylate) (PGMA‐g‐PNIPAM), were successfully prepared by combination of controlled/living free radical polymerization and click chemistry. Effects of grafting length and density on the thermoresponsive behavior, aggregating mean diameter, and self‐assembly morphology are systematically investigated. The thermosensitive characteristics of graft polymers in aqueous solution prove that the length and graft density had positive co‐relationship with the lower critical solution temperature value and mean diameter of micelles as well as the size distribution, while the effect of graft length of polymers is more significant than that of density. Transmission electron microscopy analysis shows that the conformations of PGMA₄₅‐g‐PNIPAM₂₀ and PGMA₄₅‐g‐PNIPAM₄₆ with longer length and bigger grafting density in aqueous solutions are spherical nanoparticles with the increasing trend of the diameters, while that of PGMA₄₅‐g‐PNIPAM_{(73, 50%)} shows a spherical‐like morphology, which indicates that the graft length and density have a significant effect on the mean diameter of micelle but not on the self‐assembly morphology. These results reveal that to obtain desired thermoresponsive behavior and self‐assembly morphology of functional polymers, it is essential to design and fabricate the structure of graft polymers with proper length and graft density. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2442–2453     

Polymer electrolyte membranes based on polystyrenes with phosphonic acid via long alkyl side chains

A series of polystyrenes with phosphonic acid ( 5 ) via long alkyl side chains (4, 6, and 8 methylene units) were prepared by the radical polymerization of the corresponding diethyl ω‐(4‐vinylphenoxy)alkylphosphonates, followed by the hydrolysis with trimethylsilyl bromide. The resulting phosphonated polystyrene membranes had a high oxidative stability against Fenton's reagent at room temperature. The membranes prepared from 5 exhibited a very low water uptake, similar to that of Nafion 117 over the wide range of 30 to 80% relative humidity (RH). The proton conductivities of these membranes are lower than that of Nafion 117 in the range of 30 to 90% RH, but comparable or higher than those of the reported phosphonated polymers with higher IEC values, such as the phosphonated poly(N‐phenylacrylamide) (PDPAA, IEC: 6.72 mequiv/g) and fluorinated polymers with pendant phosphonic acids (M47, IEC: 8.5 mequiv/g), at low RH conditions despite the much lower IEC values (3.0–3.8 mequiv/g) of these membranes. These results suggest that the flexible pendant side chains of 5 would contribute to the formation of hydrogen‐bonding networks by considering the very low water uptake of these polymers. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Proton‐conductive polymer nanocomposite membranes prepared from telechelic fluorinated polymers containing perfluorosulfonic acid side chains

New classes of fluorinated polymer–polysilsesquioxane nanocomposites have been designed and synthesized. The synthesis method includes radical polymerization using the functional benzoyl peroxide initiator for the telechelic fluorinated polymers with perfluorosulfonic acids in the side chains and a subsequent in situ sol–gel condensation of the prepared triethoxylsilane‐terminated fluorinated polymers with oxide precursors. The telechelic polymer and nanocomposites have been carefully characterized by ¹H and ¹⁹F NMR, FTIR, TGA, and TEM. The ion‐exchange capacity (IEC), water uptake, the state of the absorbed water, and transport properties of the composite membranes have been extensively studied as a function of the content and structure of the fillers. Unlike the conventional Nafion/silica composites, the proton conductivity of the prepared membranes increases steadily with the addition of small amounts of the polysilsesquioxane fillers. In particular, the sulfopropylated polysilsesquioxane‐based nanocomposites display proton conductivities greater than Nafion. This is attributed to the presence of pendant sulfonic acids in the fillers, which increases IEC and offers continuous proton transport channels between the fillers and the polymer matrix. The methanol permeability of the prepared membranes has also been examined. Lower methanol permeability and higher electrochemical selectivity than those of Nafion have been demonstrated in the polysilsesquioxane‐based nanocomposites. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Poly(ether ketone)s bearing pendent sulfonate groups via copolyacylation of a sulfonated monomer and isomeric AB‐type comonomers

Poly(ether ketone)s bearing pendent sulfonate groups (SPEK‐x/y/z) have been successfully synthesized via copolyacylation of a presulfonated monomer SBP and two isomeric AB‐type self‐condensable comonomers, that is, 4‐phenoxybenzoic acid (p‐POBA) and 3‐phenoxybenzoic acid (m‐POBA). Proton‐exchange membranes (PEMs) with precisely controlled ion‐exchange capacity (IEC) and high strength can be readily prepared from these ionomers. PEMs prepared from p‐POBA other than m‐POBA exhibit much higher dimensional stability and proton conductivity at elevated temperature above 60 °C, showing prominent isomeric (para vs. meta) effects of polymer structural units. Furthermore, properties of PEMs prepared from p‐POBA are optimized by tuning IEC. SPEK‐1.0/2.2/0 with an IEC of 1.84 mmol g^?1 exhibits acceptable swelling, much higher proton conductivity, and lower methanol permeability than commercial Nafion 115, implying potential application in direct methanol fuel cells. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 200–207     

Nanofiltration membranes based on poly(vinylidene fluoride‐co‐chlorotrifluoroethylene)‐graft‐poly(styrene sulfonic acid)

Graft copolymers comprising poly(vinylidene fluoride‐co‐chlorotrifluoroethylene) backbone and poly(styrene sulfonic acid) side chains, i.e. P(VDF‐co‐CTFE)‐g‐PSSA were synthesized using atom transfer radical polymerization (ATRP) for composite nanofiltration (NF) membranes. Direct initiation of the secondary chlorinated site of CTFE units facilitates grafting of PSSA, as revealed by FT‐IR spectroscopy. The successful “grafting from” method and the microphase‐separated structure of the graft copolymer were confirmed by transmission electron microscopy (TEM). Wide angle X‐ray scattering (WAXS) also showed the decrease in the crystallinity of P(VDF‐co‐CTFE) upon graft copolymerization. Composite NF membranes were prepared from P(VDF‐co‐CTFE)‐g‐PSSA as a top layer coated onto P(VDF‐co‐CTFE) ultrafiltration support membrane. Both the rejections and the flux of composite membranes increased with increasing PSSA concentration due to the increase in SO₃H groups and membrane hydrophilicity, as supported by contact angle measurement. The rejections of NF membranes containing 47 wt% of PSSA were 83% for Na₂SO₄ and 28% for NaCl, and the solution flux were 18 and 32 L/m² hr, respectively, at 0.3 MPa pressure. Copyright © 2008 John Wiley & Sons, Ltd.     

Linear and comb‐like acrylonitrile/N‐isopropylacrylamide copolymers synthesized by the combination of RAFT polymerization and ATRP

We describe the synthesis of three novel thermoresponsive copolymers of acrylonitrile (AN) with N‐isopropylacrylamide (NIPAM) by a combination of reversible addition‐fragmentation chain transfer (RAFT) polymerization and atom transfer radical polymerization (ATRP). Linear copolymer polyacrylonitrile (PAN)‐b‐PNIPAM was directly prepared by RAFT polymerization. Comb‐like copolymers were synthesized by ATRP using brominated AN/2‐hydroxyethyl methacrylate copolymers as macroinitiators, which were prepared by RAFT polymerization. FT‐IR, NMR, and GPC were employed to characterize the synthesized copolymers. Results indicate that the polymerization processes can be well controlled and the resultant copolymers have well‐defined structures as well as narrow polydispersity. Then dense films were fabricated from these thermoresponsive copolymers and the surface wettability was evaluated by water contact angle measurements at different temperatures. It is found that the surface wettability is temperature‐dependant and both the transition temperature and decrement of water contact angle are affected by the copolymer shapes as well as the length of PNIPAM blocks. Considering the excellent fiber‐ and membrane‐forming properties of PAN‐based copolymers, the obtained thermoresponsive copolymers are latent materials for functional fibers and membranes. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 92–102, 2009     

Highly proton conducting proton‐exchange membranes based on fluorinated poly(arylene ether ketone)s with octasulfonated segments

A new bisphenol monomer containing a pair of electron‐rich tetra‐arylmethane units was designed and synthesized. Based on this monomer, along with commercial 4,4′‐(hexafluoroisopropylidene)diphenol A and 4,4′‐difluorobenzophenone, a series of novel poly(arylene ether ketone)s containing octasulfonated segments of varying molar percentage (x) (6F‐SPAEK‐x) were successfully synthesized by polycondensation reactions, followed by sulfonation. Tough, flexible, and transparent membranes, exhibiting excellent thermal stabilities and mechanical properties were obtained by casting. 6F‐SPAEK‐x samples exhibited appropriate water uptake and swelling ratios at moderate ion exchange capacities (IECs) and excellent proton conductivities. The highest proton conductivity (215 mS cm⁻¹) is observed for hydrated 6F‐SPAEK‐15 (IEC = 1.68 meq g⁻¹) at 100 °C, which is more than 1.5 times that of Nafion 117. Furthermore, the 6F‐SPAEK‐10 membrane exhibited comparable proton conductivity (102 mS cm⁻¹) to that of Nafion 117 at 80 °C, with a relatively low IEC value (1.26 meq g⁻¹). Even under 30% relative humidity, the 6F‐SPAEK‐20 membrane (2.06 meq g⁻¹) showed adequate conductivity (2.1 mS cm⁻¹) compared with Nafion 117 (3.4 mS cm⁻¹). The excellent comprehensive properties of these membranes are attributed to well‐defined nanophase‐separated structures promoted by strong polarity differences between highly ionized and fluorinated hydrophobic segments. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 25–37     

Effect of water sorption on oxygen‐barrier properties of aromatic polyamides

Aromatic polyamides based on poly(m‐xylylene adipamide) (MXD‐based polyamides) and poly(hexamethylene isophthalamide) (HMD‐based polyamides) were examined. Insight into the excellent gas‐barrier properties was obtained by the characterization of the effect of water sorption on the thermal transitions, density, refractive index, free‐volume hole size, and oxygen‐transport properties. Reversing the carbonyl position with respect to the amide nitrogen substantially lowered the oxygen permeability of MXD‐based polyamides in comparison with that of HMD‐based polyamides by facilitating hydrogen‐bond formation. The resulting restriction of conformational changes and segmental motions reduced diffusivity. The primary effect of water sorption was a decrease in the glass‐transition temperature (T_g) attributed to plasticization by bound water. No evidence was found to support the idea that sorbed water filled holes of free volume. When the polymer was in the glassy state, the drop in T_g accounted for hydration‐dependent changes in the density, refractive index, and free‐volume hole size. The correlation of the oxygen solubility with T_g and density confirmed the concept of oxygen sorption as filling holes of excess free volume. In some cases, water sorption produced a glass‐to‐rubber transition. The onset of rubbery behavior was associated with a minimum in the oxygen permeability. The glass‐to‐rubber transition also facilitated the crystallization of MXD‐based polymers, which complicated the interpretation of oxygen‐transport behavior at higher relative humidity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1365–1381, 2005     

Free volume and water vapor transport properties of temperature‐sensitive polyurethanes

Segmented polyurethanes (PU) with crystalline soft segments were prepared with different crystalline polyols as soft segments. Morphology and microstructure of the PUs were investigated using Differential Scanning Calorimetry (DSC), Wide‐angle X‐ray Diffraction (WAXD), and Positron Annihilation Lifetime Spectra (PALS). Water vapor transport properties of the PU membranes were measured in the temperature range of crystal melting of their soft segments. Dependence of free volume of the PUs on temperature and the relationship between the free volume and water vapor permeability of the PU membranes were investigated. The results show that the mean free volume size and fractional free volume increase more rapidly in the temperature range of crystal melting than in other temperature intervals. In the specified temperature range, water vapor permeability of the polyester based PU membranes increases significantly, caused by the steep increase in free volume, due to crystal melting of the soft segments. Water vapor permeability of the polyester based PUs exhibits approximately direct correlation with the fractional free volume within the temperature range of crystal melting. © 2005 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 43: 1865–1872, 2005     

Synthesis of sulfonated aromatic poly(ether amide)s and their application to proton exchange membrane fuel cells

A series of wholly aromatic sulfonated poly(ether amide)s (SPEAs) containing a sulfonic acid group on the dicarbonyl aromatic ring were prepared via a polycondensation reaction of sulfonated terephthalic acid (STA), terephthalic acid (TA), and aromatic diamine monomers. The degree of sulfonation was readily controlled by adjusting the monomer feed ratio of STA and TA in the polymerization process, and randomly sulfonated polymers with an ion exchange capacity (IEC) of 1.0–1.8 mequiv/g were prepared using this protocol. The chemical structures of randomly sulfonated polymers were characterized using NMR and FT‐IR spectroscopies. Gel permeation chromatography analysis of SPEAs indicated the formation of high‐molecular‐weight sulfonated polymer. Tough and flexible SPEA membranes were obtained from solution of N,N‐dimethylacetamide, and thermogravimetric analysis of these membranes showed a high degree of thermal stability. Compared with previously reported sulfonated aromatic polyamides, these new SPEAs showed a significantly lower water uptake of 10–30%. In proton conductivity measurements, ODA‐SPEA‐70 (IEC = 1.80 mequiv/g), which was obtained from polycondensation of 4,4′‐oxydianiline and 70 mol % STA, showed a comparable proton conductivity (105 mS/cm) to that of Nafion 117 at 80 °C. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 485–496, 2009     

Thermoplastic amphiphilic conetworks

Our main objective was the design, synthesis, characterization, and testing of a novel class of materials, thermoplastic amphiphilic conetworks (TP‐APCNs). A further objective was the evaluation of TP‐APCNs as biomaterials, for example, as immunoisolatory membranes in a bioartificial pancreas, or as extended‐wear soft contact lenses. The synthesis of the first TP‐APCNs was accomplished by blending an amphiphilic graft polymer, poly(dimethyl acryl amide)‐g‐polydimethylsiloxane (PDMAAm‐g‐PDMS), with a commercial PDMS‐containing polyurethane (PU). The common PDMS segments coalesce and form a single phase, whereas the hard/crystalline segments of the PU physically crosslink the blend. The properties of TP‐APCNs can be controlled by the graft/PU ratio and segment molecular weights. TP‐APCNs with cocontinuous hydrophilic and hydrophobic phases were prepared as demonstrated by swelling in water and n‐heptane. Depending on the blend ratio and molecular weights, optically clear water‐swollen TP‐APCNs with 0.5–4 MPa tensile strength, 70–280% elongation, together with 2–11 × 10^?7 cm²/s glucose permeability, and 1.2–8 × 10^?8 cm²/s insulin permeability were prepared. TP‐APCNs are processible by casting and molding. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 682–691, 2009     

Synthesis of poly(ethylene oxide) with pending 2,2,6,6‐tetramethylpiperidine‐1‐oxyl groups and its further initiation of the grafting polymerization of styrene

A new stratagem for the synthesis of amphiphilic graft copolymers of hydrophilic poly(ethylene oxide) as the main chain and hydrophobic polystyrene as the side chains is suggested. A poly(ethylene oxide) with pending 2,2,6,6‐tetramethylpiperidine‐1‐oxyls [poly(4‐glycidyloxy‐2,2,6,6‐tetramethylpiperidine‐1‐oxyl‐co‐ethylene oxide)] was first prepared by the anionic ring‐opening copolymerization of ethylene oxide and 4‐glycidyloxy‐2,2,6,6‐tetramethylpiperidine‐1‐oxyl, and then the graft copolymerization of styrene was completed with benzoyl peroxide as the initiator in the presence of poly(4‐glycidyloxy‐2,2,6,6‐tetramethylpiperidine‐1‐oxyl‐co‐ethylene oxide). The polymerization of styrene was under control, and comblike, amphiphilic poly(ethylene oxide)‐g‐polystyrene was obtained. The copolymer and its intermediates were characterized with size exclusion chromatography, ¹H NMR, and electron spin resonance in detail. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3836–3842, 2006     

Fluorescent poly(aryl ether)s containing benzo[g]phthalazine and benzo[g]isoquinoline moieties

2,3‐Bis(4‐fluorobenzoyl)naphthalene was synthesized, and poly(aryl ether)s were prepared through a reaction with various bisphenols in the solvent N,N‐dimethylacetamide in the presence of potassium carbonate. Through a reaction with hydrazine or benzylamine, the corresponding benzo[g]phthalazine or benz[g]isoquinoline was formed. The conversion into heterocyclic structures resulted in a significant straightening of the chains, and the glass‐transition temperatures, inherent viscosities, and apparent molecular weights from size exclusion chromatography were significantly increased, whereas the solubilities decreased. The diketone‐containing polymers were colorless, and the benzo[g]phthalazine‐ and benz[g]isoquinoline‐containing polymers were yellow. The diketone polymers showed strong UV absorption maxima up to 350 nm, with fluorescence emission maxima around 475 nm. The heterocyclic polymers had broad absorptions up to around 450 nm, with strong emission maxima around 550 nm. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5745–5753, 2004     

Synthesis and characterization of SPE membrane based on sulfonated FEP‐g‐acrylic acid by radiation induced graft copolymerization for PEM fuel cell

A Novel solid polymer electrolyte (SPE) membrane containing both ? COOH and ? SO₃H group has been prepared by simultaneous method of radiation grafting of acrylic acid onto FEP followed by sulfonation. The presence of weakly acidic acrylic acid controls the swelling in water while ? SO₃H group provides conductivity due to its strongly ionic characteristic. FEP‐g‐acrylic acid and its sulfonated derivatives were characterized by their properties. While the mechanical properties decreased, other properties such as ion exchange capacity (IEC), water uptake and ionic conductivity increased with increase in graft content. These properties further changed on sulfonation. Acrylic acid being weakly acidic in nature, conductivity values of the grafted membrane were quite low. However, introduction of strong ? SO₃H group resulted in conductivity closer to Nafion 117. Few sulfonated membranes have been tested with respect to H₂/O₂ fuel cell performance. Short‐term fuel cell test for 100 hr gave a stable performance. These membranes are less expensive compared to Nafion. Copyright © 2004 John Wiley & Sons, Ltd.     

Chemically modified proton‐conducting membranes based on sulfonated polyimides: Improved water stability and fuel‐cell performance

A series of branched/crosslinked sulfonated polyimide (B/C‐SPI) membranes were prepared and evaluated as proton‐conducting ionomers based on the new concept of in situ crosslinking from sulfonated polyimide (SPI) oligomers and triamine monomers. Chemical branching and crosslinking in SPI oligomers with 1,3,5‐tris(4‐aminophenoxy)benzene as a crosslinker gave the polymer membranes very good water stability and mechanical properties under an accelerated aging treatment in water at 130 °C, despite their high ion‐exchange capacity (2.2–2.6 mequiv g^?1). The resulting polymer electrolytes displayed high proton conductivities of 0.2–0.3 S cm^?1 at 120 °C in water and reasonably high conductivities of 0.02–0.03 S cm^?1 at 50% relative humidity. In a single H₂/O₂ fuel‐cell system at 90 °C, they exhibited high fuel‐cell performances comparable to those of Nafion 112. The B/C‐SPI membranes also displayed good performances in a direct methanol fuel cell with methanol concentrations as high as 50 wt % that were superior to those of Nafion 112. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3751–3762, 2006     

Characteristic properties of film prepared from poly(L‐lactide)‐grafted dextran of a relatively high sugar unit content as a degradable biomaterial

To develop novel biomedical soft materials with degradability, amphiphilic poly(L ‐lactide)‐grafted dextrans (Dex‐g‐PLLAs) of relatively high sugar unit contents were synthesized with the trimethylsilyl protection method. The characteristic properties of solution‐cast films prepared from the obtained Dex‐g‐PLLAs were investigated. The water absorption and degradation rate of the Dex‐g‐PLLA films increased with increasing sugar unit content. The morphology of the bulk phase and top surface of the Dex‐g‐PLLA films was evaluated with transmission electron microscopy and atomic force microscopy, respectively. The bulk phase of the Dex‐g‐PLLA films with a sugar unit content of 16–25 wt % was found by transmission electron microscopy to form a lamellar type of phase‐separated structure composed of approximately 80–100‐nm‐wide nanodomains because of their amphiphilic and branched structures. The hydrophobic top surface for a Dex‐g‐PLLA film with a sugar unit content of 25 wt % covered with PLLA segments was confirmed by atomic force microscopy phase images to be easily converted to a wettable top surface covered with hydrophilic dextran aggregates showing an 8–10‐nm‐wide honeycomb pattern by means of annealing in water. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 6402–6409, 2006     

Synthesis,self‐assembly,and thermosensitive properties of ethyl cellulose‐g‐P(PEGMA) amphiphilic copolymers

Ethyl cellulose graft poly(poly(ethylene glycol) methyl ether methacrylate) (EC‐g‐P(PEGMA)) amphiphilic copolymers were synthesized via atom transfer radical polymerization (ATRP) and characterized by FTIR, ¹H NMR, and gel permeation chromatography. Reaction kinetics analysis indicated that the graft copolymerization is living and controllable. The self‐assembly and thermosensitive property of the obtained EC‐g‐P(PEGMA) amphiphilic copolymers in water were investigated by dynamic light scattering, transmission electron microscopy, and transmittance. It was found that the EC‐g‐P(PEGMA) amphiphilic copolymers can self‐assemble into spherical micelles in water. The size of the micelles increases with the increase of the side chain length. The spherical micelles show thermosensitive properties with a lower critical solution temperature around 65 °C, which almost independent on the graft density and the length of the side chains. The obtained EC‐g‐P(PEGMA) graft copolymers have both the unique properties of poly(ethylene glycol) and cellulose, which may have the potential applications in biomedicine and biotechnology. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 46: 6907–6915, 2008