Carbon‐nanotube Modified Screen‐printed Electrode for the Simultaneous Determination of Nitrite and Uric Acid in Biological Fluids Using Batch‐injection Amperometric Detection

A portable electroanalytical system applied for rapid and simultaneous determination of uric acid (UA) and nitrite (NIT) in human biological fluids (urine, saliva and blood) is reported. The system is based on batch‐injection analysis with multiple‐pulse amperometric (BIA‐MPA) detection using screen‐printed electrodes (SPEs) modified with multi‐walled carbon nanotubes. Sample dilution in optimized electrolyte (0.1 mol L⁻¹ Britton‐Robinson buffer pH 2) followed by injection of 100 μL on the electrode surface using an electronic micropipette is performed. UA is detected at +0.45 V and both UA+NIT at +0.70 V. Linear calibration plots for UA and NIT were obtained over the range of 1–500 μmol L⁻¹ with detection limits of 0.05 and 0.06 μmol L⁻¹, respectively. For comparison, a differential‐pulse voltammetric (DPV) method was optimized, and linear calibration plots for UA and NIT were obtained over range of 1–30 μmol L⁻¹ and 1–40 μmol L⁻¹ with detection limits of 0.1 and 0.3 μmol L⁻¹, respectively. BIA‐MPA is highly precise (RSD<1.3 %), fast (160 h⁻¹) and free from sample‐matrix interferences as recovery values ranged from 77 to 121 % for spiked samples (short contact time of sample aliquot with SPE). Contrarily, recovery tests conducted using DPV did not provide adequate recovery values (>150 %), probably due to the longer contact time of the SPE with the biological samples during analysis leading to a severe interference of sample matrices.     

Application of response surface methodology for optimization of trace amount of diazinon preconcentration in natural waters and biological samples by carbon mesoporous CMK‐3

Preconcentration of trace amounts of diazinon by carbon mesoporous CMK‐3 in water and biological samples and measurement by high‐performance liquid chromatography were investigated. CMK‐3 was prepared using hexagonal SBA‐15 as the template. The synthesized materials were characterized by X‐Ray diffraction (XRD), Fourier transform infrared spectroscopy, Brunaur–Emmet–Teller, transmission electron microscopy and Boehm titration method. The preconcentration procedure was optimized using a multivariate optimization approach following a two‐stage process. The effect of analytical parameters including the amount of the CMK‐3 as an adsorbent, pH, type and volume of eluent and flow rate of eluent and sample were studied by a screening project, then the effective parameters were optimized by response surface methodology based on central composite design. The average extraction efficiency of diazinon under optimal conditions (CMK‐3 dosage = 25 mg, sample flow rate = 2.5 mL min⁻¹, eluent flow rate = 1.25 mL min⁻¹, volume of methanol as an eluent =3.5 mL and initial pH = 6) was 97.11%, which agrees well with the predicted response value (97.93%). The linearity of the method was in the range of 0.5–100 μg L⁻¹ with a correlation coefficient of 0.997. Enrichment factor, limit of detection and limit of quantification were 285.7, 0.09 and 0.23 μg L⁻¹, respectively. The relative standard deviation (RSD) under optimum conditions was 2.21% (n = 5). The proposed method was applied to determine diazinon in real water and biological samples. Recovery of diazinon from real samples was between 95.80 and 104.94% with an RSD of 0.19–4.65%. Thus, this method is suitable for the preconcentration and determination of diazinon in real water and biological samples.     

Evaluation of needle trap micro‐extraction and solid‐phase micro‐extraction: Obtaining comprehensive information on volatile emissions from in vitro cultures

Volatile organic compounds (VOCs) emitted from in vitro cultures may reveal information on species and metabolism. Owing to low nmol L⁻¹ concentration ranges, pre‐concentration techniques are required for gas chromatography–mass spectrometry (GC–MS) based analyses. This study was intended to compare the efficiency of established micro‐extraction techniques – solid‐phase micro‐extraction (SPME) and needle‐trap micro‐extraction (NTME) – for the analysis of complex VOC patterns. For SPME, a 75 μm Carboxen®/polydimethylsiloxane fiber was used. The NTME needle was packed with divinylbenzene, Carbopack X and Carboxen 1000. The headspace was sampled bi‐directionally. Seventy‐two VOCs were calibrated by reference standard mixtures in the range of 0.041–62.24 nmol L⁻¹ by means of GC–MS. Both pre‐concentration methods were applied to profile VOCs from cultures of Mycobacterium avium ssp. paratuberculosis. Limits of detection ranged from 0.004 to 3.93 nmol L⁻¹ (median = 0.030 nmol L⁻¹) for NTME and from 0.001 to 5.684 nmol L⁻¹ (median = 0.043 nmol L⁻¹) for SPME. NTME showed advantages in assessing polar compounds such as alcohols. SPME showed advantages in reproducibility but disadvantages in sensitivity for N‐containing compounds. Micro‐extraction techniques such as SPME and NTME are well suited for trace VOC profiling over cultures if the limitations of each technique is taken into account.     

Preparation of dummy template‐imprinted polymers for the rapid extraction of nonsteroidal anti‐inflammatory drugs residues in aquatic environmental samples

A molecularly imprinted polymer was synthesized and applied as a sorbent in the solid‐phase extraction device. The imprinted polymer was characterized by fourier‐transform infrared spectroscopy and scanning electron microscope. The results revealed that imprinted polymer possess sensitive selectivity and reliable adsorption properties for five NSAIDs. The imprinted polymer was successfully applied to the pre‐concentration for five NSAIDs in different water samples prior to UPLC‐MS/MS. In the early studies, several factors were investigated, including pH adjustment, the kind of elution solvent and the volume of elution solvent. Finally, we found that the pH 5 and an aliquot of 2 mL methanol were suitable for the water samples. The limits of detection and limits of quantitation of five nonsteroidal anti‐inflammatory drugs varied from 0.007 to 0.480 μg L⁻¹ and 0.03 to 1.58 μg L⁻¹, respectively. The spiking recoveries of the target analytes were 50.33‐127.64% at the levels of 0.2 μg L⁻¹, 2 μg L⁻¹ and 5 μg L⁻¹. The precision and accuracy of this method showed a great increase compared with traditional solid‐phase extraction. The developed method was successfully applied to extraction and analysis of NSAIDs in different water samples with satisfactory results which could help us better understand their environmental fate and risk to ecological health.     

Tellurium Film Electrodes Deposited on Carbon and Mesoporous Carbon Screen‐printed Substrates for Anodic Stripping Voltammetric Determination of Copper

The performance of screen‐printed electrodes modified in situ with tellurium film for the anodic stripping voltammetric (ASV) determination of Cu(II) is reported. It was found that two types of screen‐printed substrates, namely carbon and mesoporous carbon, were optimal for this application. The selected in situ tellurium film modified electrodes were applied for the square wave ASV determination of copper at μg L⁻¹ concentration levels. Well‐defined and reproducible Cu oxidation stripping peaks were produced at a potential more negative than the anodic dissolution of tellurium. The highest sensitivity of Cu determination was achieved in 0.05 M HCl containing 50 μg L⁻¹ Te(IV) after 300 s of accumulation at −0.5 V. Using the optimized procedure, a linear range from 2 to 35 μg L⁻¹ of Cu(II) was obtained with a detection limit of 0.5 μg L⁻¹ Cu(II) (S/N=3) for 300 s of deposition time. Both sensors, carbon TeF‐SPE and mesoporous carbon TeF‐SPE, were successfully applied for the quantification of Cu in a certified reference surface water sample.     

In‐vitro Aluminum Determination and Preconcentration in Blood of Dialysis Patients Based on Ionic Liquid Dispersive Liquid‐Liquid Biomicroextraction by 2‐Amino‐3‐(1H‐imidazol‐4‐yl)propanoic Acid

In this study, trace amounts of aluminum in serum of dialysis patients were chelated with 2‐Amino‐3‐(1H‐imidazol‐4‐yl)propanoic acid (Histidine) and determined by electro‐thermal atomic absorption spectrometry (ETAAS). A fast and efficient method based on ionic liquid dispersive liquid‐liquid bio‐micro‐extraction (IL‐DLLBME) was developed for the determination of Al cation in human blood serum samples. In this work, a small amount of 1‐Hexyl‐3‐methylimmidazolum hexafluorophosphate ([HMIM] [PF₆]) as an extractant solvent was dissolved in acetone as a dispersant solvent and then the binary solution was rapidly injected by a syringe into the serum containing Al³⁺,Which have already in‐vitro chelated by Histidine amino acid (Al‐His) at pH = 6.5. After separation, the settled IL‐phase was dissolved in ethanol up to 200 μL and 20 μL of samples injected into the ET‐AAS by auto‐sampler. Various parameters have been studied and optimized for 10 mL of sample. Under the optimum conditions, the enrichment factor (EF), limit of detection (LOD) and working range (peak area mode) were obtained 53, 15 ng L^?1 and 0.05‐4.1 μg L^?1 respectively. In vitro Al chelation showed that His can significantly decrease aluminum concentration in serum of dialysis patients. Validation of methodology was confirmed by standard reference material (SRM).     

Study of immobilized metal affinity chromatography sorbents for the analysis of peptides by on‐line solid‐phase extraction capillary electrophoresis‐mass spectrometry

Several commercial immobilized metal affinity chromatography sorbents were evaluated in this study for the analysis of two small peptide fragments of the amyloid β‐protein (Aβ) (Aβ(1–15) and Aβ(10–20) peptides) by on‐line immobilized metal affinity SPE‐CE (IMA‐SPE‐CE). The performance of a nickel metal ion (Ni(II)) sorbent based on nitrilotriacetic acid as a chelating agent was significantly better than two copper metal ion (Cu(II)) sorbents based on iminodiacetic acid. A BGE of 25 mM phosphate (pH 7.4) and an eluent of 50 mM imidazole (in BGE) yielded a 25‐fold and 5‐fold decrease in the LODs by IMA‐SPE‐CE‐UV for Aβ(1–15) and Aβ(10–20) peptides (0.1 and 0.5 μg/mL, respectively) with regard to CE‐UV (2.5 μg/mL for both peptides). The phosphate BGE was also used in IMA‐SPE‐CE‐MS, but the eluent needed to be substituted by a 0.5% HAc v/v solution. Under optimum preconcentration and detection conditions, reproducibility of peak areas and migration times was acceptable (23.2 and 12.0%RSD, respectively). The method was more sensitive for Aβ(10–20) peptide, which could be detected until 0.25 μg/mL. Linearity for Aβ(10–20) peptide was good in a narrow concentration range (0.25–2.5 μg/mL, R² = 0.93). Lastly, the potential of the optimized Ni(II)‐IMA‐SPE‐CE‐MS method for the analysis of amyloid peptides in biological fluids was evaluated by analyzing spiked plasma and serum samples.     

Fabrication of β‐Cyclodextrin/Glycine/Carbon Nanotubes Electrochemical Neurotransmitters Sensor – Application in Ultra‐sensitive Determination of DOPAC in Human Serum

In this work, an electrochemical sensor was constructed by applying two successive thin layers of glycine‐carbon nanotubes mixture and β‐cyclodextrin (CNTs‐Gly)/CD over glassy carbon electrode surface for some neurotransmitters determination. A host‐guest interaction between CD and neurotransmitters molecules is expected and resulted in enhanced sensitivity, selectivity and stability of sensor response. Other components of the sensor are crucial for the unique electrochemical response. Carbon nanotubes allowed large surface area for glycine distribution that provided hydrogen bonding to CD moieties and contributed to facilitated charge transfer. It was possible to determine 3,4‐dihydroxy phenyl acetic acid (DOPAC) in the linear range of 0.1 μmol L⁻¹ to 80 μmol L⁻¹ with detection limit of 9.40 nmol L⁻¹, quantification limit of 31.5 nmol L⁻¹ and sensitivity of 4.16 μA/μmol L⁻¹. The proposed sensor was applied in synthetic cerebrospinal fluids samples using random standard addition method. Also, the proposed sensor was used to determine DOPAC in presence of common interferences and acceptable recovery results were achieved for its analysis in real blood serum. Figures of merit for (CNTs‐Gly)/CD composite in terms of precision, robustness, repeatability and reproducibility were reported.     

Determination of Trace Methyl Tert‐Butyl Ether in Water Samples Using Dispersive Liquid‐Liquid Microextraction Coupled with GC‐FID

A rapid and sensitive analytical method has been developed for trace analysis of methyl tert‐butyl ether (MTBE) in water samples using dispersive liquid‐liquid microextraction and gas chromatography with flame ionization detection. Factors relevant to the microextraction efficiency, such as the kind of extraction solvent, the disperser solvent and their volumes, the effect of salt, sample solution temperature and the extraction time were investigated and optimized. Under the optimal conditions the linear dynamic range of MTBE was from 0.2 to 25.0 μg L^?1 with a correlation coefficient of 0.9981 and a detection limit of 0.1 μg L^?1. The relative standard deviation (RSD%) was less than 5.1% (n = 3) and the recovery values were in the range of 97.8 ± 0.9%. Finally, the proposed method was successfully applied for the analysis of MTBE in aqueous samples.     

Simple determination of betaine,l‐carnitine and choline in human urine using self‐packed column and column‐switching ion chromatography with nonsuppressed conductivity detection

A sequential online extraction, clean‐up and separation system for the determination of betaine, l ‐carnitine and choline in human urine using column‐switching ion chromatography with nonsuppressed conductivity detection was developed in this work. A self‐packed pretreatment column (50 × 4.6 mm, i.d.) was used for the extraction and clean‐up of betaine, l ‐carnitine and choline. The separation was achieved using self‐packed cationic exchange column (150 × 4.6 mm, i.d.), followed by nonsuppressed conductivity detection. Under optimized experimental conditions, the developed method presented good analytical performance, with excellent linearity in the range of 0.60–100 μg mL⁻¹ for betaine, 0.75–100 μg mL⁻¹ for l ‐carnitine and 0.50–100 μg mL⁻¹ for choline, with all correlation coefficients (R²) >0.99 in urine. The limits of detection were 0.15 μg mL⁻¹ for betaine, 0.20 μg mL⁻¹ for l ‐carnitine and 0.09 μg mL⁻¹ for choline. The intra‐ and inter‐day accuracy and precision for all quality controls were within ±10.32 and ±9.05%, respectively. Satisfactory recovery was observed between 92.8 and 102.0%. The validated method was successfully applied to the detection of urinary samples from 10 healthy people. The values detected in human urine using the proposed method showed good agreement with the measurement reported previously.     

Quantification of 1‐(propan‐2‐ylamino)‐4‐propoxy‐9H‐thioxanthen‐9‐one (TX5), a newly synthetized P‐glycoprotein inducer/activator,in biological samples: method development and validation

A simple, rapid and economical method was developed and validated for the analysis and quantification of 1‐(propan‐2‐ylamino)‐4‐propoxy‐9H ‐thioxanthen‐9‐one (TX5), a P‐glycoprotein inducer/activator, in biological samples, using reverse‐phase high‐performance liquid chromatography (HPLC). A C₁₈ column and a mobile phase composed of methanol–water (90/10, v /v) with 1% (v/v) triethylamine, at a flow rate of 1 mL/min, were used for chromatographic separation. TX5 standards (0.5–150 μm ) were prepared in human serum. Methanol was used for TX5 extraction and serum protein precipitation. After filtration, samples were injected into the HPLC apparatus and TX5 was quantified by a conventional UV detector at 255 nm. The TX5 retention time was 13 min in this isocratic system. The method was validated according to ICH guidelines for specificity/selectivity, linearity, accuracy, precision, limits of detection and quantification (LOD and LOQ) and recovery. The method was proved to be selective, as there were no interferences of endogenous compounds with the same retention time of TX5. Also, the developed method was linear (r ² ≥ 0.99) for TX5 concentrations between 0.5 and 150 μm and the LOD and LOQ were 0.08 and 0.23 μm , respectively. The results indicated that the reported method could meet the requirements for TX5 analysis in the trace amounts expected to be present in biological samples.     

Vortex‐assisted liquid–liquid microextraction for the rapid screening of short‐chain chlorinated paraffins in water

The rapid screening of trace levels of short‐chain chlorinated paraffins in various aqueous samples was performed by a simple and reliable procedure based on vortex‐assisted liquid–liquid microextraction combined with gas chromatography and electron capture negative ionization mass spectrometry. The optimal vortex‐assisted liquid–liquid microextraction conditions for 20 mL water sample were as follows: extractant 400 μL of dichloromethane; vortex extraction time of 1 min at 2500 × g; centrifugation of 3 min at 5000 × g; and no ionic strength adjustment. Under the optimum conditions, the limit of quantitation was 0.05 μg/L. Precision, as indicated by relative standard deviations, was less than 9% for both intra‐ and inter‐day analysis. Accuracy, expressed as the mean extraction recovery, was above 91%. The vortex‐assisted liquid–liquid microextraction with gas chromatography and electron capture negative ionization mass spectrometry method was successfully applied to quantitatively extract short‐chain chlorinated paraffins from samples of river water and the effluent of a wastewater treatment plant, and the concentrations ranged from 0.8 to 1.6 μg/L.     

Detection of 20‐hydroxyecdysone in calf urine by comparative liquid chromatography/high‐resolution mass spectrometry and liquid chromatography/tandem mass spectrometry measurements: application to the control of the potential misuse of ecdysteroids in cattle

Ecdysteroids, which are steroid hormones in invertebrates, but which are also present in plants, could potentially be used as anabolic agents in food‐producing animals. The control of ecdysteroid misuse in cattle relies on the development of an efficient method for their detection in biological matrices at trace levels (µg L⁻¹). In order to propose an analytical procedure dedicated to the identification of excreted 20‐hydroxyecdysone (20E) in urine and faecal samples of breeding animals, a comparative study of the spectrometric behaviour of these compounds was carried out both by LC/(ESI‐)/HRMSⁿ (hybrid linear ion trap – orbital trap) and by LC/(ESI+)/MS/MS (triple quadrupole). This study revealed the formation of a large number of product ions both in positive and negative ion mode, corresponding to losses of water molecules and specific cleavages on the side chain. The sample preparation consisted of sequential purification on two solid‐phase extraction cartridges (SPE octadecylsilyl and SPE silica). The detection limits were around 0.5 µg L⁻¹ in the selected reaction monitoring (SRM) mode and recoveries above 60% were obtained. The method was successfully applied to the analysis of real samples collected from calves treated with 60 mg 20E over 4 days. Analysis of the samples allowed the investigation of the kinetics of elimination of 20E in calf urine and determination of the time‐frame for the control of potential abuse. Copyright © 2008 John Wiley & Sons, Ltd.     

Therapeutic drug monitoring of mitotane: Analytical assay and patient follow‐up

Adrenocortical carcinoma (ACC) is an aggressive malignancy of the adrenal gland. Mitotane (o ,p' ‐DDD) is the most effective chemotherapy for ACC. According to the literature, mitotane plasma trough concentrations within 14–20 mg L⁻¹ are correlated with a higher response rate with acceptable toxicity. Therapeutic drug monitoring (TDM) of mitotane is therefore recommended. The aim of this study was to propose a robust and simple method for mitotane quantification in plasma. The validation procedures were based on international guidelines. Sample preparation consisted of a single protein precipitation with methanol using 100 μL of plasma. The supernatant was submitted to liquid chromatography coupled with ultra‐violet detection at 230 nm. Mitotane retention time was 7.1 min. The limit of detection was 0.1 mg L⁻¹ and the limit of quantification was 0.78 mg L⁻¹. The assay demonstrated a linear range of 0.78–25 mg L⁻¹ with correlation coefficients (r ²) at 0.999. Inter‐ and intra‐assay precision was <4.85%. Evaluation of accuracy showed a deviation <13.69% from target concentration at each quality control level. This method proved easy and rapid to perform mitotane TDM and required a small volume of sample. It was successfully applied to routine TDM in our laboratory.     

Cetyl‐alcohol‐reinforced hollow fiber solid/liquid‐phase microextraction and HPLC–DAD analysis of ezetimibe and simvastatin in human plasma and urine

A new cetyl‐alcohol‐reinforced hollow fiber solid/liquid‐phase microextraction (CA–HF–SLPME) followed by high‐performance liquid chromatography–diode array detection (HPLC–DAD) method was developed for simultaneous determination of ezetimibe and simvastatin in human plasma and urine samples. To prepare the CA–HF–SLPME device, the cetyl‐alcohol was immobilized into the pores of a 2.5 cm hollow fiber micro‐tube and the lumen of the micro‐tube was filled with 1‐octanol with the two ends sealed. Afterwards, the prepared device was introduced into 10 mL of the sample solution containing the analytes with agitation. Under optimized conditions, calibration curves plotted in spiked plasma and urine samples were linear in the ranges of 0.363–25/0.49–25 μg L^?1 for ezetimibe/simvastatin and 0.193–25/0.312–25 μg L^?1 for ezetimibe/simvastatin in plasma and urine samples, respectively. The limit of detection was 0.109/0.174 μg L^?1 for ezetimibe/simvastatin in plasma and 0.058/0.093 μg L^?1 for ezetimibe/simvastatin in urine. As a potential application, the proposed method was applied to determine the concentration of selected analytes in patient plasma and urine samples after medication and satisfactory results were achieved. In comparison with reference methods, the CA–HF–SLPME–HPLC–DAD method demonstrates considerable potential in the biopharmaceutical analysis of selected drugs.     

HILIC LC‐MS for the determination of 2′‐C‐methyl‐cytidine‐triphosphate in rat liver

A very accurate and selective LC‐MS/MS method was developed and validated for the quantification of 2′‐C‐modified nucleoside triphosphate in liver tissue samples. An efficient pretreatment procedure of liver tissue samples was developed, using a fully automated SPE procedure with 96‐well SPE plate (weak anion exchange sorbent, 30 mg). Nucleotide hydrophilic interaction chromatography has been performed on an aminopropyl column (100 mm×2.0 mm, 3 μm) using a gradient mixture of ACN and ACN/water (5:95 v/v) with 20 mM ammonium acetate at pH 9.45 as mobile phase at 300 μL/min flow rate. The 2′‐C‐modified nucleoside triphosphate was detected in the negative ESI mode in multiple reaction monitoring (MRM) mode. Calibration curve was linear over the 0.05–50 μM concentration range. Satisfying results, confirming the high reliability of the established LC‐MS/MS method, were obtained for intraday precision (CV = 2.5–9.1%) and accuracy (92.6–94.8%) and interday precision (CV = 9.6–11.5%) and accuracy (94.4–102.4%) as well as for recovery (82.0–112.6%) and selectivity. The method has been successfully applied for pharmacokinetic studies of 2′‐C‐methyl‐cytidine‐triphosphate in liver tissue samples.     

Simultaneous determination of short‐chain fatty acids in human feces by HPLC with ultraviolet detection following chemical derivatization and solid‐phase extraction segmental elution

Short‐chain fatty acids are currently the most studied metabolites of gut microbiota, but the analysis of them, simultaneously, is still challenging due to their unique property and wide concentration range. Here, we developed a sensitive and versatile high‐performance liquid chromatography with ultraviolet detection method, using pre‐column derivatization and solid‐phase extraction segmental elution, for the quantification of both major and trace amounts of short‐chain fatty acids in human feces. Short‐chain fatty acids were converted to 3‐nitrophenylhydrazine‐derived analytes, and then solid‐phase extraction segmental elution was used for extraction of major analytes and enrichment of trace analytes. The method validation showed limits of quantitation ?0.04 mM, and coefficient of determination > 0.998 at a wide range of 0.04–8.0 mM. The intra‐ and interday precision of analytes were all within accepted criteria, and the recoveries were 96.12 to 100.75% for targeted analytes in fecal samples. This method was successfully applied in quantification of eight analytes in human feces, which therefore could provide a sensitive and versatile high‐performance liquid chromatography with ultraviolet detection method for precise and accurate quantitation of short‐chain fatty acids in human feces.     

Voltammetric Method for the Simultaneous Determination of Melatonin and Pyridoxine in Dietary Supplements Using a Cathodically Pretreated Boron‐doped Diamond Electrode

The simultaneous voltammetric determination of melatonin (MT) and pyridoxine (PY) has been carried out at a cathodically pretreated boron‐doped diamond electrode. By using cyclic voltammetry, a separation of the oxidation peak potentials of both compounds present in mixture was about 0.47 V in Britton‐Robinson buffer, pH 2. The results obtained by square‐wave voltammetry allowed a method to be developed for determination of MT and PY simultaneously in the ranges 1–100 μg mL⁻¹ (4.3×10⁻⁶–4.3×10⁻⁴ mol L⁻¹) and 10–175 μg mL⁻¹ (4.9×10⁻⁵–8.5×10⁻⁴ mol L⁻¹), with detection limits of 0.14 μg mL⁻¹ (6.0×10⁻⁷ mol L⁻¹) and 1.35 μg mL⁻¹ (6.6×10⁻⁶ mol L⁻¹), respectively. The proposed method was successfully to the dietary supplements samples containing these compounds for health‐caring purposes.     

Square Wave‐Anodic Stripping Voltammetric Determination of Copper at a Bismuth Film/Glassy Carbon Electrode Using 3‐[(2‐Mercapto‐Vinyl)‐Hydrazono]‐ 1,3‐Dihydro‐Indol‐2‐One

This study reports a highly sensitive electrochemical sensor based on Bi film modified glassy carbon electrode (BiF/GCE) for total determination and speciation trace concentrations of copper(II) ions in environmental water samples. Square wave‐adsorptive anodic stripping voltammetric (SW‐ASV) experiment was performed for monitoring selective accumulation of copper(II) with reagent 3‐[(2‐mercapto‐vinyl)‐hydrazono]‐1,3‐dihydro‐indol‐2‐one (MHDI) at pH 9–10. The mechanism of the electrode reaction of Cu²⁺‐MHDI complex was safely assigned. The sensor exhibited a wide linear range (3.22×10⁻⁹–2.0×10⁻⁷ mol L⁻¹) with lower limits of detection (LOD) and quantitation (LOQ) of 9.6×1⁻¹⁰ and 3.22×10⁻⁹ mol L⁻¹, respectively (R²=0.9993). The proposed sensor exhibited interference from active metal ions e. g. Cd, Hg. The performance of the proposed method was compared successfully with most of the reported methods and comparable efficiencies were obtained. The analytical utility of the proposed SW‐ASV method has been successfully validated for trace analysis of copper(II) in environmental water samples. The method offers a precise, accurate approach with good reproducibility, robustness, ruggedness, and cost effectiveness.     

Determination of chemotherapeutic agents in fish and shellfish by matrix solid‐phase dispersion and liquid chromatography‐tandem mass spectrometry

Chemicals are widely used in aquaculture and one of the main recipients of these analytes is the aquatic environment. The aim of this work was to develop and validate a simple and sensitive method for the determination of multiclass chemotherapeutic agents in farmed fish and shellfish using matrix solid‐phase dispersion and liquid chromatography‐tandem mass spectrometry. Residues of azamethiphos, three avermectins, two carbamates, and two benzoylureas were extracted from samples using silica gel as clean‐up adsorbent and 0.5% acetic acid in acetonitrile as elution solvent. The extraction conditions were investigated and optimized using an experimental design. Mass spectrometry detection was carried out in positive electrospray ionization mode with multiple‐reaction monitoring scan (except for benzoylurea family). Matrix‐matched standards were used for the drugs quantification. Good linearity (R² ≥ 0.996) was observed in the range of 5–500 μg kg^?1. Limits of detection were in the range of 1.5–3.7 μg kg^?1. Recoveries from salmon samples spiked with veterinary drugs were in the range 84.9–118%. Precision was satisfactory since relative standard deviations were lower than 10.6%. The method can be successfully applied for the analysis of fish and shellfish from aquaculture.