The influence of oxygen pressure on the kinetics of the thermal decomposition of Co3O4

The kinetics of the thermal decomposition of Co₃O₄ has been examined in the 1123–1200 K temperature and 2.66–20.73 kPa oxygen pressure range. The kinetics of this process has been deseribed in terms of a mixed-control model of reaction. The values of activation energies of diffusion and chemical reaction as well as the observed activation energy have been given. The strong dependence of the decomposition rate on temperature and oxygen pressure has been explained.     

The effect of calcination conditions on the superconducting properties of Y−Ba−Cu−O powders

Calcination conditions of the precursor powders, i.e. temperature, type of atmosphere and duration, were determined with a view to obtain superconducting powders with the most advantageous physico-chemical properties. Investigated were powders in the Y?Ba?Cu?O system prepared by the sol-gel method. Thermogravimetric examinations of the powders have revealed that the decomposition kinetics of BaCO₃ determines the formation rate of the superconducting YBa₂Cu₃O_7?x (‘123’) phase. It follows from the decomposition kinetics of BaCO₃ that the process is the most intensive in argon, whereas in static air and oxygen it is the slowest. The phase composition analysis (XRD) and low-temperature magnetic susceptibility measurements of the calcinated powders, confirm the above mentioned changes in the decomposition kinetics. The reaction of barium carbonate can be completed if the calcination process is conducted at the temperature of 850°C for 25 h, yielding easily sinterable powders for obtaining single-phase superconducting bulk samples with advantageous functional parameters.     

Investigation on The Thermal Properties of Fe2O(SO4)2. Part II

Fe₂O(SO₄)₂ is a secondary product of the decomposition of FeSO₄⋅H₂O. Part I of this study presents results on the synthesis of Fe₂O(SO₄)₂ in gaseous environment containing either low or high concentration of oxygen. In this paper the existence of differences between the structures of Fe₂O(SO₄)₂ and Fe₂(SO₄)₃ is proved on the basis of a detailed thermal study of Fe₂O(SO₄)₂ upon dynamic heating (differential thermal analysis) and upon isothermal heating (thermal-analytic balance) in various gaseous environments as well as by presenting kinetic data on the processes of decomposition of both compounds. This revised version was published online in July 2006 with corrections to the Cover Date.     

超级铝热剂Al/Fe2O3的制备、表征及对环三亚甲基三硝胺热分解的影响

采用水热法制备了中空短棒状纳米Fe2O3,并用超声分散法将其与纳米Al颗粒复合为单金属氧化基超级铝热剂.利用X射线粉末衍射(XRD)、傅里叶变换红外(FTIR)光谱、扫描电镜及能量散射光谱仪(SEM-EDS)对样品进行表征.并运用差示扫描量热法(DSC)对比研究了超级铝热剂Al/Fe2O3、Al粉和纳米Fe2O3对环三亚甲基三硝胺(RDX)热分解特性的影响.结果表明:超级铝热剂的加入改变了RDX的热分解过程,并加剧了RDX的二次气相反应;随着超级铝热剂含量的增加,RDX的分解峰峰形发生了明显的改变;Al/Fe2O3、Al粉和Fe2O3对RDX热分解的作用主要表现为二次分解峰逐渐明显且峰温降低.     

Kinetics of the thermal decomposition of [Co(NH3)6]2(C2O4)3·4H2O

The thermal decomposition of [Co(NH₃)₆]₂(C₂O₄)₃·4H₂O was studied under isothermal conditions in flowing air and argon. Dissociation of the above complex occurs in three stages. The kinetics of the particular stages thermal decomposition have been evaluated. The R_N and/or A_M models were selected as those best fitting the experimental TG curves. The activation energies,E, and lnA were calculated with a conventional procedure and by a new method suggested by Kogaet al. [10, 11]. Comparison of the results have showed that the Arrhenius parameters values estimated by the use of both methods are very close. The calculated activation energies were in air: 96 kJ mol^–1 (R_1.575, stage I); 101 kJ mol^–1 (Ain1.725 stage II); 185 kJ mol^–1 (A _2.9, stage III) and in argon: 66 kJ mol^–1 (A _1.25, stage I); 87 kJ mol^–1 (A _1.825, stage II); 133 kJ mol^–1 (A _2.525, stage III).     

Thermal properties and kinetics study of charged LiCoO2 by TG and C80 methods

The thermal stability of lithium-ion battery cathode could substantially affect the safety of lithium-ion battery. In order to disclose the decomposition kinetics of charged LiCoO₂ used in lithium ion batteries, thermogravimetric analyzer (TG) and C80 microcalorimeter were employed in this study. Four stages of mass losses were detected by TG and one main exothermic process was detected by C80 microcalorimeter for the charged LiCoO₂. The chemical reaction kinetics is supposed to fit by an Arrhenius law, and then the activation energy is calculated as E _a=148.87 and 88.87 kJ mol⁻¹ based on TG and C80 data, respectively.     

The thermal dehydration and decomposition of Ba[Cu(C2O4)2(H2O)]·5H2O

The thermal behaviour of Ba[Cu(C₂O₄)₂(H₂O)]·5H₂O in N₂ and in O₂ has been examined using thermogravimetry (TG) and differential scanning calorimetry (DSC). The dehydration starts at relatively low temperatures (about 80°C), but continues until the onset of the decomposition (about 280°C). The decomposition takes place in two major stages (onsets 280 and 390°C). The mass of the intermediate after the first stage corresponded to the formation of barium oxalate and copper metal and, after the second stage, to the formation of barium carbonate and copper metal. The enthalpy for the dehydration was found to be 311±30 kJ mol^–1 (or 52±5 kJ (mol of H₂O)^–1). The overall enthalpy change for the decomposition of Ba[Cu(C₂O₄)₂] in N₂ was estimated from the combined area of the peaks of the DSC curve as –347 kJ mol^–1. The kinetics of the thermal dehydration and decomposition were studied using isothermal TG. The dehydration was strongly deceleratory and the -time curves could be described by the three dimensional diffusion (D3) model. The values of the activation energy and the pre-exponential factor for the dehydration were 125±4 kJ mol^–1 and (1.38±0.08)×10¹⁵ min^–1, respectively. The decomposition was complex, consisting of at least two concurrent processes. The decomposition was analysed in terms of two overlapping deceleratory processes. One process was fast and could be described by the contracting-geometry model withn=5. The other process was slow and could also be described by the contracting-geometry model, but withn=2.The values ofE _a andA were 206±23 kJ mol^–1 and (2.2±0.5)×10¹⁹ min^–1, respectively, for the fast process, and 259±37 kJ mol^–1 and (6.3±1.8)×10²³ min^–1, respectively, for the slow process.Dedicated to Prof. Menachem Steinberg on the occasion of his 65th birthday     

Mechanism of activation and catalysis of chemiluminescence by Eu(fod)3 chelate in thermal decomposition of adamantylideneadamantane-1,2-dioxetane

Complexation of the chelate both with dioxetane and with adamantanone (2), the product of decomposition of dioxetane, have an important effect on chemiluminescence (CL) in thermal decomposition of adamantylideneadamantane-1,2-dioxetane (1) in the presence of Eu(fod)₃ chelate. The stability constants of Eu(fod)₃·1 and Eu(fod)₃·2 complexes were obtained. It was found that Eu(fod)₃ catalyzes and activates chemiluminescent decomposition of1. The rate constant (k₂) of decomposition of the Eu(III)·1 complex was determined from the kinetics of quenching of CL, and the activation parameters were determined from the temperature curve. Luminescence from the⁵D_1-level of the Eu(III) ion was detected in the CL spectrum and was correlated with direct (bypassing the triplet of the ligand) transfer of excitation energy from2 _t* to the luminescent levels of Eu(III) in the geometrically distorted complex Eu(fod)₃·2.Institute of Organic Chemistry, Ural Branch, Russian Academy of Sciences, 450054 Ufa. Translated from Izvestiya Akademii Nauk, Seriya Khimicheskaya, No. 5, pp. 1056–1063, May, 1992.     

Thermal decomposition of hydrogen peroxide in the presence of sulfuric acid

Hydrogen peroxide (H₂O₂) is popularly employed as a reaction reagent in cleaning processes for the chemical industry and semiconductor plants. By using differential scanning calorimetry (DSC) and vent sizing package 2 (VSP2), this study focused on the thermal decomposition reaction of H₂O₂ mixed with sulfuric acid (H₂SO₄) with low (0.1, 0.5 and 1.0 N), and high concentrations of 96 mass%, respectively. Thermokinetic data, such as exothermic onset temperature (T ₀), heat of decomposition (ΔH _d), pressure rise rate (dP/dt), and self-heating rate (dT/dt), were obtained and assessed by the DSC and VSP2 experiments. From the thermal decomposition reaction on various concentrations of H₂SO₄, the experimental data of T ₀, ΔH, dP/dt, and dT/dt were obtained. Comparisons of the reactivity for H₂O₂ and H₂O₂ mixed with H₂SO₄ (lower and higher concentrations) were evaluated to corroborate the decomposition reaction in these systems.     

The Formation of Ferroelectric Bismuth Titanate (Bi4Ti3O12) from an Aqueous Metal-Chelate Gel

Bismuth titanate (Bi₄Ti₃O₁₂) was synthesized by an aqueous solution-gel process starting from solutions of bismuth acetate and a peroxocitrato-Ti(IV) complex. To gain insight into the thermal decomposition pattern of the gel several thermal analysis techniques were employed: DTA, TGA-EGA (evolved gas analysis by on-line coupling to a FTIR or mass spectrometer) and HT-DRIFT. Transmission electron micrographs showed that the gel is chemically homogeneous down to ca. 5 nm and that this homogeneity is preserved throughout the heat treatment. High-temperature X-ray diffraction measurements were used to make an in situ study of the phase formation. It has been found that single phase Bi₄Ti₃O₁₂ is formed at 625°C.     

On the reduction of Cr3+ during the thermal decomposition of fluorochromates(III) with nitrogen containing cations

The thermal decomposition of [CO(NH₂)₂H]CrF₆·H₂O, (C₃N₆H₈)CrF₅·H₂O and the solid state reaction of CrF₃ and melamine are investigated under non-reciprocal quasi-static conditions and compared with the thermal behaviour of other fluorochromates(III) ([Cr(NH₃)₆]CrF₆, (NH₄)₃CrF and [C(NH₂)₃]₃CrF₆). The comparison of the results shows that the amount of chromium(II) in the final product is determined by the thermal stability and consequently by the decomposition temperature of the intermediates. Neither bonding properties in the starting materials nor the absolute amount of generated NH₃ influence the composition of the final product.     

Synthesis and thermal decomposition of bismuth peroxotitanate to Bi2Ti2O7

Bi-peroxotitanate was synthesized by a peroxo method and after thermal decomposition Bi₂Ti₂O₇ was obtained. DTA, TG and DSC curves of Bi₂[Ti₂(O₂)₄(OH)₆]5H₂O were recorded and used to determine isothermal conditions suitable for obtaining the intermediate samples corresponding to the phases observed during the thermal decomposition. The samples were identified by quantitative analysis, IR spectroscopy and X-ray analysis. The experimental results were used to propose a mechanism of thermal decomposition of the investigated compound to a nanosized Bi₂Ti₂O₇. The optimum conditions were also determined for obtaining Bi₂Ti₂O₇, which is applicable for piezosensors.     

Synthesis and thermal investigation of Na2Cd(SO4)2·2H2O

The synthesis and thermal decomposition of Na₂(SO₄)₂·2H₂O in both air and nitrogen are described. The synthesis was performed by two different procedures, but in both cases the same product was obtained, corresponding to the general formula given above. The crystals obtained were investigated by methods of X-ray powder diffraction, and chemical and thermal analysis. The differences in thermal decomposition in air and nitrogen are discussed.     

Thermal decomposition of cobalt nitrato compounds: Preparation of anhydrous cobalt(II)nitrate and its characterisation by Infrared and Raman spectra

The thermal decomposition of Co(NO₃)₂·6H₂O (1) as well as that one of NO[Co(NO₃)₃] (Co(NO₃)₂·N₂O₄) (2) was followed by thermogravimetric (TG) measurements, X-ray recording and Raman and IR spectra. The stepwise decomposition reactions of 1 and 2 leading to anhydrous cobalt(II)nitrate (3) were established. In N₂ atmosphere, cobalt oxides are finally formed whereas in H₂/N₂ (10% H₂) cobalt metal is produced. Rapid heating of cobalt(II)nitrate hexahydrate causes melting (formation of a hydrate melt) and therefore side reactions in the hydrate melt by incoupled reactions and evolution/evaporation of different species as, e.g., HNO₃, NO₂, etc. In case of larger amounts in dense packing in the sample container, the formation of oxo(hydoxo)nitrates is possible at higher temperature. For 2, its thermal decomposition to 3 was followed and its decomposition mechanism is proposed.     

Heat capacity and thermodynamical properties of the crystal of [RE2(Glu)2(H2O)8](ClO4)4·H2O (RE = Nd, Eu, Dy)

Thermodynamical data of rare earth complexes with amino acid are important for engineering chemistry and fundamental chemistry. However, they have rarely been reported. In this work, a series of crystalline complexes of rare earth perchlorate coordinated with glutamic acid have been synthesized in water medium, and their thermodynamical data, including the heat capacity in low temperature range and the standard enthalpy of formation, were determined. These complexes were identified to be [RE₂(Glu)₂(H₂O)₈](ClO₄)₄·H₂O (RE = Nd, Eu, Dy) by using thermogravimetric analysis (TG), differential thermal analysis (DTA), and chemical and elementary analyses. Their purity has been determined. No melting points were observed for all the three complexes. The heat capacity of the complexes was measured by an adiabatic calorimeter from 79 to 370 K. Abnormal heat capacity values were detected for two of the complexes and the decomposition range of one complex was found. The temperature, enthalpy change and entropy change of the decomposition processes of the three complexes were calculated. The polynomial equations of heat capacity in the experimental temperature range have been obtained by least squares fitting. The standard enthalpy of formation was determined by an isoperibol reaction calorimeter at 298.15 K. Supported by the Research Fund of Beijing Institute of Petro-Chemical Technology (N06-06)     

A New Method for the Preparation of Co3O4 Nanoparticles

In this study, a novel method was used to prepare well-separated and spherical tricobalt tetraoxide (Co₃O₄) nanosized particles. The overall process involves three steps: preparation of insoluble carboxyl-containing grafted starch copolymer (ISC), formation of precursor (ISC-Co), decomposition of ISC-Co, and phase transition of Co₃O₄ nanoparticles. The Infrared spectra used for ISC and ISC-Co are discussed. The decomposition of the precursor was studied by thermogravimetric-differential thermal analysis, the crystalline phase was characterized by x-ray diffraction, and the size distribution and shape of particles were observed by transmission electron microscopy. Translated from Journal of Northwest Normal University (Natural Science Edition), 2005, 5(5) (in Chinese)     

Thermal Decomposition of Bi(III), Cd(II), Pb(II) and Cu(II) Thiocyanates

Thermal decomposition of Bi(SCN)₃, Cd(SCN)₂, Pb(SCN)₂ and Cu(SCN)₂ has been studied. The thermal analysis curves and the diffraction patterns of the solid intermediate and final products of the pyrolysis are presented. The gaseous products of the decomposition (SO₂ and CO₂) were detected and quantitatively determined. Thermal, X-ray and chemical analyses have been used to establish the nature of the reactions occurring at each stage in the decomposition.This revised version was published online in November 2005 with corrections to the Cover Date.     

Synthesis and thermal decomposition of potassium peroxotitanate to K2Ti2O5

Potassium peroxotitanate was synthesized by the peroxo method. During the thermal decomposition K₂Ti₂O₅ can be obtained. The isothermal conditions for decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O were determined on the base of DTA, TG and DSC results. DTA and TG curves were recorded in the temperature range 20 and 900°C at a heating rate of 10°C min^–1. The obtained intermediate compounds were characterized by means of quantitative analysis and IR spectroscopy. The mechanism of thermal decomposition of K₂[Ti₂(O₂)₂(OH)₆]·3H₂O to K₂Ti₂O₅ was studied. The optimal conditions for obtaining K₂Ti₂O₅ were determined (770°C for 10 h).     

Kinetic analysis of the thermal stability of lithium silicates (Li4SiO4 and Li2SiO3)

The kinetics describing the thermal decomposition of Li₄SiO₄ and Li₂SiO₃ have been analysed. While Li₄SiO₄ decomposed on Li₂SiO₃ by lithium sublimation, Li₂SiO₃ was highly stable at the temperatures studied. Li₄SiO₄ began to decompose between 900 and 1000 °C. However, at 1100 °C or higher temperatures, Li₄SiO₄ melted, and the kinetic data of its decomposition varied. The activation energy of both processes was estimated according to the Arrhenius kinetic theory. The energy values obtained were −408 and −250 kJ mol⁻¹ for the solid and liquid phases, respectively. At the same time, the Li₄SiO₄ decomposition process was described mathematically as a function of a diffusion-controlled reaction into a spherical system. The activation energy for this process was estimated to be −331 kJ mol⁻¹. On the other hand, Li₂SiO₃ was not decomposed at high temperatures, but it presented a very high preferential orientation after the heat treatments.     

Study of Zircon-Dolomite Reactions Monitored by Neutron Thermodiffractometry

The reaction mechanism that takes place in ZrSiO₄-Mg Ca(CO₃)₂ mixtures was studied in air up to 1300°C by collecting neutron diffraction patterns during the heating ramp. Neutron diffraction intensities were used to monitor and establish the mechanism of reaction that occurs in successive stages. (a) MgCa(CO₃)₂ decomposition yielding MgO and CaCO₃; (b) CaCO₃ decomposition; (c) reactions between CaO, MgO, and ZrSiO₄ involving the formation of phases such as: tetragonal-ZrO₂, α-Ca₂SiO₄, and Ca₃MgSi₂O₈, some of them acting as transitory phases; and (d) formation of CaZrO₃. The results obtained by this technique agree with data obtained by differential thermal analysis and thermogravimetry. The final product has a porous structure, due to the release of CO₂, with a very narrow pore size distribution (≈1 μm). This open-porosity can be controlled by tailoring the reaction sintering process.