Two color up-conversion emissions of Er<Superscript>3+</Superscript>-doped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> nanopowders prepared by non-aqueous sol-gel method

Er³⁺-doped Al₂O₃ nanopowders have been prepared by the non-aqueous sol-gel method using the aluminum isopropoxide as precursor, acetylacetone as a chelating agent, nitric acid as a catalyzer, and hydrated erbium nitrate as a dopant under isopropanol environment. The different phase structure, including three crystalline types of (Al, Er)₂O₃ phases, α, γ, θ, and an Er–Al–O stoichiometric compound phase, Al₁₀Er₆O₂₄, was observed for the 0.01–0.5 mol% Er³⁺-doped Al₂O₃ nanopowders at the sintering temperature of 1,000 °C. The green and red up-conversion emissions centered at about 523, 545 and 660 nm, corresponding respectively to the ²H_11/2, ⁴S_3/2→⁴I_15/2 and ⁴F_9/2→⁴I_15/2 transitions of Er³⁺, were detected by a 978 nm semiconductor laser diodes excitation. With increasing Er³⁺ doping concentration from 0.01 to 0.1 mol%, the intensity of the green and red emissions increased with a decrease of the intensity ratio of the green to red emission. When the Er³⁺ doping concentration rose to 5 mol%, the intensity of the green and red emissions decreased with an increase of their intensity ratio. The maximum intensity of both the green and red emissions with the minimum of intensity ratio was obtained, respectively, for the 0.1 mol% Er³⁺-doped Al₂O₃ nanopowders composed of a single α-(Al,Er)₂O₃ phase. The intensity ratio of the green emission at 523 and 545 nm increased monotonously for all Er³⁺ doping concentrations. The two-photon absorption up-conversion process was involved in the green and red up-conversion emissions of the Er³⁺-doped Al₂O₃ nanopowders.     

Yb<Superscript>3+</Superscript> → Er<Superscript>3+</Superscript> energy transfer in Al<Subscript>2</Subscript>O<Subscript>3</Subscript> and temperature characteristic of near-infrared photoluminescence

For the Er³⁺–Yb³⁺ codoped Al₂O₃ powders, the strong near-infrared photoluminescence (PL) centered at 1.535 μm derived from the energy transfer (ET) from Yb³⁺ to Er³⁺ was detected by a 978 nm laser diode excitation. Compared with that of Er³⁺ doped Al₂O₃ powders, the PL intensity enhanced about 9 times, the full width at half maximum (FWHM) extended from 82 to 90 nm, and the lifetime increased from 3.22 to 4.17 ms for Er³⁺–Yb³⁺ codoped Al₂O₃ powders at room temperature. The ET coefficient of 2.18 × 10⁻¹⁸ cm³ s⁻¹ from Yb³⁺ to Er³⁺ was obtained based on the rate equations. The decrease of PL intensity with increasing temperature in the range of 298–733 K was observed, due to thermally enhanced nonradiative relaxation ⁴I_13/2 → ⁴I_15/2 dominated over thermally enhanced phonon-assisted ET in the Er³⁺–Yb³⁺ codoped Al₂O₃.     

GdAlO_3:Er~(3+),Yb~(3+)荧光粉的制备与上转换发光性能

采用共沉淀、溶胶-凝胶和固相反应法制备了GdAlO3:Er3+,Yb3+荧光粉.借助X射线衍射、扫描电子显微镜、傅里叶变换红外光谱、N2-吸附、吸收光谱和荧光光谱等手段研究了不同方法制备的GdAlO3:Er3+,Yb3+荧光粉结构、形貌、表面基团和光吸收及上转换发光性能.结果表明:用共沉淀法比固相反应法和溶胶-凝胶法可以在更温和的条件下制得纯相GdAlO3:Er3+,Yb3+荧光粉,用共沉淀法和溶胶-凝胶法制备的GdAlO3:Er3+,Yb3+荧光粉颗粒都在纳米尺寸,溶胶-凝胶法制得的样品存在相对严重的颗粒团聚现象,而用固相反应法制备的荧光粉为微米级颗粒.GdAlO3:Er3+,Yb3+荧光粉在980 nm激发的上转换发射光谱包含波长为524和546 nm的绿光与659 nm的红光,且三种方法制备的样品绿光发射强度都显著高于红光.不同方法制备的荧光粉上转换发光强度和红光/绿光强度比相差较大,共沉淀法制备的样品上转换发光强度要显著高于固相法以及溶胶-凝胶法制备的样品,而溶胶-凝胶法制备的样品发光中红光/绿光相对强度比最高.红外光谱显示,不同方法制备的GdAlO3:Er3+,Yb3+荧光粉表面OH-、CO32-及CO2官能团含量不同,溶胶-凝胶法制备的样品要明显高些.基于红外光谱、不同Er3+和Yb3+离子掺杂浓度及不同激光功率上转换发光的结果,对Er3+和Yb3+之间的能量传递过程及不同方法制备荧光粉的上转换发光性能进行了讨论.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al₂O₃-SiO₂系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho³⁺/Yb³⁺共掺以ZnAl₂O₄为主晶相的ZnO-Al₂O₃-GeO₂-SiO₂系玻璃陶瓷。因[GeO₄]四面体和[SiO₄]四面体都是玻璃网络形成体,讨论了GeO₂取代SiO₂对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO₂的取代量为10.55%（w/w）时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色（546 nm）和弱的红色（650 nm）上转换发光,并研究了不同Ho³⁺/Yb³⁺掺杂比对样品上转换发光的影响,最终结果表明当Ho³⁺/Yb³⁺掺杂比为1：11（n/n）时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

Strong visible up-conversion emissions and thermometric applications of Er<Superscript>3+</Superscript>–Yb<Superscript>3+</Superscript> codoped Al<Subscript>2</Subscript>O<Subscript>3</Subscript> prepared by the sol–gel method

The Er³⁺–Yb³⁺ codoped Al₂O₃ has been prepared by the sol–gel method using the aluminium isopropoxide [Al(OC₃H₇)₃]-derived Al₂O₃ sols with addition of the erbium nitrate [Er(NO₃)₃ · 5H₂O] and ytterbium nitrate [Yb(NO₃)₃ · 5H₂O]. The phase structure, including only two crystalline types of doped Al₂O₃ phases, θ and γ, was obtained for the 1 mol% Er³⁺ and 5 mol% Yb³⁺ codoped Al₂O₃ at the sintering temperature of 1,273 K. By a 978 nm semiconductor laser diodes excitation, the visible up-conversion emissions centered at about 523, 545, and 660 nm were obtained. The temperature dependence of the green up-conversion emissions was studied over a wide temperature range of 300–825 K, and the reasonable agreement between the calculated temperature by the fluorescence intensity ratio (FIR) theory and the measured temperature proved that Er³⁺–Yb³⁺ codoped Al₂O₃ plays an important role in the application of high temperature sensor.     

Intense Upconversion Luminescence of CaSc2O4:Ho3+/Yb3+ from Large Absorption Cross Section and Energy‐Transfer Rate of Yb3+

Concentration‐optimized CaSc₂O₄:0.2 % Ho³⁺/10 % Yb³⁺ shows stronger upconversion luminescence (UCL) than a typical concentration‐optimized upconverting phosphor Y₂O₃:0.2 % Ho³⁺/10 % Yb³⁺ upon excitation with a 980 nm laser diode pump. The ⁵F₄+⁵S₂→⁵I₈ green UCL around 545 nm and ⁵F₅→⁵I₈ red UCL around 660 nm of Ho³⁺ are enhanced by factors of 2.6 and 1.6, respectively. On analyzing the emission spectra and decay curves of Yb³⁺: ²F_5/2→²F_7/2 and Ho³⁺: ⁵I₆→⁵I₈, respectively, in the two hosts, we reveal that Yb³⁺ in CaSc₂O₄ exhibits a larger absorption cross section at 980 nm and subsequent larger Yb³⁺: ²F_5/2→Ho³⁺: ⁵I₆ energy‐transfer coefficient (8.55×10^?17 cm³ s^?1) compared to that (4.63×10^?17 cm³ s^?1) in Y₂O₃, indicating that CaSc₂O₄:Ho³⁺/Yb³⁺ is an excellent oxide upconverting material for achieving intense UCL.     

Infrared‐to‐Visible Light Conversion in Er3+–Yb3+:Lu3Ga5O12 Nanogarnets

Er³⁺–Yb³⁺ co‐doped Lu₃Ga₅O₁₂ nanogarnets were prepared and characterized; their structural and luminescence properties were determined as a function of the Yb³⁺ concentration. The morphology of the nanogarnets was studied by HRTEM. Under 488 nm excitation, the nanogarnets emit green, red, and near‐infrared light. The decay curves for the (⁴S_3/2, ²H_11/2) and ⁴F_9/2 levels of the Er³⁺ions exhibit a non‐exponential nature under resonant laser excitation and their effective lifetimes are found to decrease with an increase in the Yb³⁺ concentration from 1.0 to 10.0 mol %. The non‐exponential decay curves are well fitted to the Inokuti–Hirayama model for S=8, indicating that the mechanism of interaction for energy transfer between the optically active ions is of dipole–quadrupole type. Upon 976 nm laser excitation, an intense green upconverted emission is clearly observed by the naked eyes. A significant enhancement of the red‐to‐green intensity ratio of Er³⁺ ions was observed with an increase in Yb³⁺ concentration. The power dependence and the dynamics of the upconverted emission confirm the existence of two‐photon upconversion processes for the green and red emissions.     

Enhanced upconversion emission in Er3+-doped tellurite glass containing silver nanoparticles

Er³⁺-doped tellurite glass containing silver nanoparticles (NPs) has been synthesized. Detailed structural and optical characterizations have been carried out. Infrared to visible frequency upconversion (UC) emission has been observed in Er³⁺-doped tellurite glass on pumping with the 976 nm radiation. Further, an enhancement in UC emission intensity of green bands (²H_11/2 → ⁴I_15/2 and ⁴S_3/2 → ⁴I_15/2) of Er³⁺ ion has been observed up to four times in presence of silver NPs in the glass annealed at 240 °C for 40 h. Though, there is enhancement in intensity in the red band (⁴F_9/2 → ⁴I_15/2) also but it is smaller. The enhancement in fluorescence intensity is attributed to local field effect due to the silver NPs.     

Spectroscopic Properties and Upconversion Studies in Ho3+/Yb3+ Co‐doped Calcium Scandate with Spectrally Pure Green emission

The optical properties of a Ho³⁺/Yb³⁺ co‐doped CaSc₂O₄ oxide material are investigated in detail. The spectral properties are described as a function of doping concentrations. The efficient Yb³⁺→Ho³⁺ energy transfer is observed. The transfer efficiency approaches 50 % before concentration quenching. The concentration‐optimized sample exhibits a strong green emission accompanied with a weak red emission, showing perfect green monochromaticity. The results of the spectral distribution, power dependence, and lifetime measurements are presented. The green, red, and near‐infrared (NIR) emissions around 545, 660, and 759 nm are assigned to the ⁵F₄+⁵S₂→⁵I₈, ⁵F₅→⁵I₈, and ⁵F₄+⁵S₂→⁵I₇ transitions of Ho³⁺, respectively. The detailed study reveals the upconversion luminescence mechanism involved in a novel Ho³⁺/Yb³⁺ co‐doped CaSc₂O₄ oxide material.     

Enhanced ultraviolet up-conversion emissions of Tm/Yb codoped YF3 nanocrystals

Tm³⁺/Yb³⁺ codoped rod-like YF₃ nanocrystals were synthesized through a facile hydrothermal method. After annealing in an argon atmosphere, the nanocrystals emitted bright blue and intense ultraviolet (UV) light under a 980-nm continuous wave diode laser excitation. Up-conversion emissions centered at ∼291 nm (¹I₆ → ³H₆), ∼347 nm (¹I₆ → ³F₄), ∼362 nm (¹D₂ → ³H₆), ∼452 nm (¹D₂ → ³F₄), ∼476 nm (¹G₄ → ³H₆), ∼642 nm (¹G₄ → ³F₄), and ∼805 nm (³H₄ → ³H₆) were recorded using a fluorescence spectrophotometer. Especially, enhanced UV emissions were studied by changing Yb³⁺/Tm³⁺ doping concentrations, the annealing temperatures, and the excitation power densities. A possible mechanism, energy transfer-cross relaxation-energy transfer (ET-CR-ET), was proposed based on a simple rate-equation model to elucidate the process of the enhanced UV emissions.     

Ho3+/Yb3+共掺ZnO-Al2O3-GeO2-SiO2玻璃陶瓷的制备和上转换发光性质

综合ZnO-Al_2O_3-SiO_2系和锗酸盐玻璃陶瓷的优点,采用熔融-晶化法首次制备了Ho~(3+)/Yb~(3+)共掺以ZnAl_2O_4为主晶相的ZnO-Al_2O_3-GeO_2-SiO_2系玻璃陶瓷。因[GeO_4]四面体和[SiO_4]四面体都是玻璃网络形成体,讨论了GeO_2取代SiO_2对玻璃陶瓷样品硬度及发光性能的影响,最终确定GeO_2的取代量为10.55%(w/w)时,玻璃陶瓷综合性能最佳。在980 nm泵浦光的激发下,发现强的绿色(546 nm)和弱的红色(650 nm)上转换发光,并研究了不同Ho~(3+)/Yb~(3+)掺杂比对样品上转换发光的影响,最终结果表明当Ho~(3+)/Yb~(3+)掺杂比为1∶11(n/n)时样品荧光强度最强,在绿色上转换发光材料方面具有潜在的应用。     

基于NaYF4:Yb3+,Er3+上转换发光纳米晶的复合微球组装及其光动力活性研究

采用微乳液法,以NaYF₄:Yb³⁺,Er³⁺纳米晶为发光基元,肽菁锌(ZnPc)光敏分子与十八碳烯-马来酸酐共聚物(PMAO)为功能分子,一步组装获得了NaYF₄-ZnPc-PMAO复合微球,此微球同时具备成像与光动力活性功能,NaYF₄可作为低生物背景的荧光成像剂,同时其上转换发光可以敏化ZnPc用于光动力活性研究,PMAO分子经过简单的水解反应即可实现表面羧基功能化。TEM,Zeta电位与PL测试证实了微球的结构与性能。利用荧光共聚焦成像技术实现了对Hela细胞的发光成像;进一步通过单线态氧监测及980 nm光照下的MTT法细胞活性测试表明微球具有光动力活性功能。     

La7O6(BO3)(PO4)2:Eu3+/Tb3+荧光材料的制备及其光致发光性能

采用优化的高温固相方法制备了稀土离子Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂系荧光材料,并对其物相行为、晶体结构、光致发光性能和热稳定性进行了详细研究。结果表明,La₇O₆（BO₃）（PO₄）₂：Eu³⁺材料在紫外光激发下能够发射出红光,发射光谱中最强发射峰位于616 nm处,为⁵D₀→⁷F₂特征能级跃迁,Eu³⁺的最优掺杂浓度为0.08,对应的CIE坐标为（0.610 2,0.382 3）;La₇O₆（BO₃）（PO₄）₂：Tb³⁺材料在紫外光激发下能够发射出绿光,发射光谱中最强发射峰位于544 nm处,对应Tb³⁺的⁵D₄→⁷F₅能级跃迁,Tb³⁺离子的最优掺杂浓度为0.15,对应的CIE坐标为（0.317 7,0.535 2）。此外,对2种材料的变温光谱分析发现Eu³⁺和Tb³⁺掺杂的La₇O₆（BO₃）（PO₄）₂荧光材料均具有良好的热稳定性。     

Comparative investigation on structure and luminescence properties of fluoride phosphors codoped with Er/Yb

This paper reports on comparative investigation of structure and luminescence properties of tetragonal LiYF₄ and BaYF₅, and hexagonal NaYF₄ phosphors codoped with Er³⁺/Yb³⁺ by a facile hydrothermal synthesis. The products were characterized by X-ray diffractometer, scanning electron microscope, and photoluminescence spectroscopy. Intense visible emissions centered at around 525, 550 and 650 nm, originated from the transitions of ²H_11/2 → ⁴I_15/2, ⁴S_3/2 → ⁴I_15/2, and ⁴F_9/2 → ⁴I_15/2 of Er³⁺, respectively, have been observed in all the samples upon excitation with a 980 nm laser diode, and the involved mechanisms have been explained. Based on the green up-conversion emission performance, the Yb³⁺ concentrations of Er³⁺/Yb³⁺-codoped LiYF₄, BaYF₅, and NaYF₄ phosphors have been optimized to be 10, 20, and 20 mol.%, respectively. The quadratic dependence of fluorescence on excitation laser power has confirmed that two-photon contribute to up-conversion of the green–red emissions.     

Investigation on the upconversion luminescence of Sr3AlO4F:Yb3+, Er3+, Ho3+ phosphors

To develop new emission-tunable upconversion (UC) phosphors, the Sr₃AlO₄F:5%Yb³⁺, xEr³⁺, yHo³⁺ (0 ≤ x ≤ 1%, 0 ≤ y ≤ 1%) samples were prepared by conversional solid-state reaction method, and their luminescence properties upon 980 nm excitation were studied. Upon 980 nm excitation, Yb³⁺-Er³⁺ codoped Sr₃AlO₄F shows a predominant emission peak between 645 and 700 nm which is attributed to the ⁴F_9/2-⁴I_15/2 transition of Er³⁺, and the Er³⁺ green emissions have been almost quenched. In this case, the yellowish green emitting light is obtained. The possible reason was interpreted by the energy level diagram and the proposed UC mechanism. For Yb³⁺-Ho³⁺ codoped Sr₃AlO₄F, three emissions are observed obviously which are all derived from the Ho³⁺ ion. The corresponding chromaticity coordinates indicate a red emission has been gained. To realize the tunable emission, the typical Sr₃AlO₄F:5%Yb³⁺, 0.2%Er³⁺, 1%Ho³⁺ phosphor was developed, and its emission spectrum includes the emission peaks of both Er³⁺ and Ho³⁺. Correspondingly, the sample gives a yellow emission.     

Synthesis and Infrared Multi‐band Absorption Properties of Core‐shell NaYF4:Yb3+, Er3+@SiO2 Nanoparticles

Due to the unique size effects, nanomaterials in infrared absorption have attracted much attention for their strong absorption in the infrared region. To achieve the infrared multi‐band absorption, we propose to synthesize a core‐shell structure nanomaterial consisting of NaYF₄:Yb³⁺, Er³⁺ core and a layer of SiO₂ as shell. A series of NaYF₄:Yb³⁺, Er³⁺ nanocrystals were synthesized through hydrothermal method by adjusting the ratio of citric acid(CA)‐to‐NaOH, and the effects of CA concentration, and NaOH concentration were studied in detail. NaYF₄:Yb³⁺, Er³⁺@SiO₂ nanoparticles were synthesized by sol‐gel method using TEOS as silica source. The results show that the core‐shell NaYF₄:Yb³⁺, Er³⁺@SiO₂ nanoparticles were successfully synthesized. Up‐conversion spectra of these nanoparticles were recorded with 980 nm laser excitation under room temperature. There are no changes of the emission centers of nanoparticles before or after silica coating, but the emission intensities of nanoparticles after silica coating are weakened. Furthermore, the property of infrared multi‐band absorption was tested through ultraviolet‐visible‐near infrared spectrophotometer and infrared absorption spectra. The results illustrate that the multi‐band infrared absorption nanomaterial was successfully synthesized.     

Enhancement of the Up-conversion Luminescence of 12CaO · 7Al2O3:Tm3+/Yb3+ Doped with Alkaline Earth Metal Ions

12CaO?·?7Al₂O₃ doped with lanthanide is characterized by remarkable and technologically important up-conversion emission. However, the low up-conversion efficiency still remains the main limitation for practical applications. To improve the efficiency, bivalent alkaline earth ions (Mg²⁺, Sr²⁺, Ba²⁺)-tridoped Tm³⁺/Yb³⁺/12CaO?·?7Al₂O₃ were synthesized through a high-temperature solid-state reaction. The up-conversion luminescence properties of the samples were investigated by X-ray diffraction, fluorescence spectral measurement pump power, and fluorescence decay curves. The luminescence intensity of samples was significantly enhanced by bivalent alkaline earth ions. 12CaO?·?7Al₂O₃ doped with Sr²⁺ ions has stronger effects on up-conversion enhancement, which is better than Mg²⁺ and Ba²⁺. The up-conversion emission intensity was enhanced by 318 times and the red emission intensity by 218 times with 10?mol% Sr²⁺ ion. Additionally, the blue and red up-conversion emission peaks at 475 and 650?nm corresponding to energy transitions of ¹G₄ → ³H₆ and ¹G₄ → ³F₄, ³F₂ → ³H₆ were characterized using steady-state rate equations.     

A general approach for selective enhancement of green upconversion emissions in Er3+ doped oxides by Yb3+–MoO4 2− dimer sensitizing

In this paper, we report a general approach to enhance the upconversion (UC) luminescence of Er³⁺ doped oxides phosphors by Yb³⁺–MoO₄ ^2? dimer sensitizing, which induced strong green UC emissions under the 976 nm laser diode excitation. By codoping of Yb³⁺ and Mo⁶⁺ in the Er³⁺ doped TiO₂ and ZnO, the green UC emissions intensity can be selectively increased about 10 and 500 times than those of Er³⁺–Yb³⁺ codoped TiO₂ and ZnO, respectively. The high excited state energy transfer between |²F_7/2, ³T₂> state of Yb³⁺–MoO₄ ^2? dimer and ⁴F_7/2 level of Er³⁺ significantly avoids the nonradiative decay processes happened at lower energy levels of Er³⁺, and then increases the green UC emissions efficiently. The proposed Yb³⁺–MoO₄ ^2? dimer sensitizing has been realized as an efficient way to enhance the green UC emissions in other Er³⁺ doped oxides phosphors. It is expected that the selective enhanced green UC emissions sensitized by Yb³⁺–MoO₄ ^2? dimer in Er³⁺ doped oxides phosphors can greatly extend their scope of applications.     

Strong upconversion–downshifting green emission from Tb<Superscript>3+</Superscript> ions in core/shell/shell-structured nanophosphors

Efficient upconversion (UC)–downshifting (DS), dual-mode-emitting NaGdF₄:Yb,Tm/NaGdF₄:Tb/NaYF₄ core/shell/shell (C/S/S) nanophosphors (NPs) were synthesized. The UC luminescence color changed from blue to sky blue after doping Tb³⁺ into NaGdF₄ shell because Tb³⁺ emission peaks via ⁵D₄ → ⁷F_J transition were observed with Tm³⁺ emission peaks via ¹D₂ → ³F₄ and ¹G₄ → ³H₆ transitions through the energy migration UC process of Yb³⁺ → Tm³⁺ → Gd³⁺ → Tb³⁺. Upon increasing the Tb³⁺ concentration in the NaGdF₄ shell from 5 to 15%, the Commission Internationale de l’Éclairage (CIE) color coordinates changed from (0.2188, 0.2390) to (0.2616, 0.3654). When NaGdF₄:Yb(49%),Tm(1%)/NaGdF₄:Tb(15%)/NaYF₄ NPs were excited using 273 nm ultraviolet light, the C/S/S NPs exhibited bright green light with CIE color coordinates of (0.3354, 0.5090) as a result of energy transfer from Gd³⁺ to Tb³⁺. These bright UC–DS, dual-mode-emitting C/S/S NPs could be applied in various applications, including multiplexed imaging and anticounterfeiting.     

Temperature-dependent six-photon upconversion fluorescence of Er

Yb³⁺/Er³⁺ codoped β-NaYF₄ microcrystals were synthesized through a facile EDTA-assisted hydrothermal method. Under 980 nm excitation, 244, 256, and 276 nm upconversion (UC) emissions were observed in NaYF₄:Yb³⁺/Er³⁺ microcrystals, which were assigned to the ²I_11/2 → ⁴I_15/2, ⁴D_7/2 → ⁴I_15/2, and ⁴G_9/2 → ⁴I_15/2 transitions of Er³⁺ ions, respectively. Successive energy transfers (ETs) from Yb³⁺ to Er³⁺ played crucial roles in populating the high-energy states of Er³⁺ ions. Power dependence analysis exhibited that 244 and 256 nm UC emissions came from six-photon processes. Temperature-dependent UC emissions of ⁴D_7/2 → ⁴I_15/2 and ²I_11/2 → ⁴I_15/2 transitions of Er³⁺ were discussed and the nonradiative relaxation (NR) process of ²I_11/2 → ⁴D_7/2 was confirmed.