Solid-Phase Extraction of Trace Amounts of Selenomethionine

Abstract

Preconcentration and separation of trace amounts of selenomethionine was investigated using several solid sorbents. The best results were obtained with copper-treated Chelex 100 chelating resin. Selenomethionine from 100 ml of solution adsorbed on 0.2 g of the resin was eluted with 8 ml of 1.5 mol/l ammonia solution and determined by electrothermal atomic absorption spectrometry. The column chromatography with Cu-Chelex and functionalized cellulose sorbent Cellex T was applied to separate organic and inorganic selenium forms.     

Flame AAS determination of lead in water with flow-injection preconcentration and speciation using functionalized cellulose sorbent

The on-line solid phase extraction of trace amount of lead in flow-injection system with flame AAS detection was investigated using cellulose sorbents with phosphonic acid and carboxymethyl groups, C(18) sorbent non-modified and modified with Pyrocatechol Violet or 8-quinolinol, commercial chelating sorbents Chelex 100 and Spheron Oxin 1000, non-polar sorbent Amberlite XAD-2 modified with Pyrocatechol Violet and several cation-exchange resins. The best dynamic characteristics of retention were observed for functionalized cellulose sorbents. For Cellex P assumed as optimum sorbent, elution with a separate fractions of nitric acid and ethanol allows the differentiation between tetraalkyllead and sum of inorganic lead and organolead species of smaller number of alkyl groups. The detection limit for the determination of inorganic Pb(II) was estimated as 0.17 microg/l. at preconcentration from 50 ml sample at a flow rate of 7 ml/min.     

The application of solid sorbents for the purification of aluminum contaminated chemicals used as modifiers in electrothermal atomic absorption spectrometry

Various microcolumns with solid sorbents (ion exchange resins, functionalised cellulose sorbents, chelating resins) have been tested with respect to their ability for the purification of aluminum contaminated chemicals used as modifiers in electrothermal atomic absorption spectrometry. The purification of NaNO₃, Mg(NO₃)₂, K₂SO₄ and (NH₄)₂HPO₄ has been the most effective with an almost 100% efficiency, when Spheron-Oxine was used as chelating resin. The sorption of aluminum from KOH solution has been found to be very high (around 90%) for all investigated sorbents. However, the best results have been obtained with anion-exchange resins. It has been difficult to purify concentrated mineral acids (HCl, H₂SO₄). A retention of aluminum above 80% has been achieved only when Cellex P, Chelex 100 or Amberlite XAD-2 have been used.     

Gold Trace Separation from some Platinum Group Metals on Cationic Exchanger in the Presence of Amines

Abstract

The sorption behaviour of gold in the presence of amines on different kinds of cationic exchangers with phosphonic groups has bee investigated. The system Cellex P - amine has been found very useful for gold separation from platinum metals. The method was adopted for trace gold determination in PdC1₂ and platinum powder.     

Preconcentration and atomic spectrometric determination of rare earth elements (REEs) in natural water samples by inductively coupled plasma atomic emission spectrometry

The usage of a variety of sorbents has been shown as promising matrix removal/preconcentration strategies for the determination of rare earth elements (REEs) in various natural water samples by inductively coupled plasma atomic emission spectrometry (ICP-AES). The sorption efficiency of various zeolites (clinoptilolite, mordenite, zeolite Y, zeolite Beta), ion-exchangers (Amberlite CG-120, Amberlite IR-120, Rexyn 101, Dowex 50W X18) and chelating resins (Muromac, Chelex 100, Amberlite IRC-718) towards REEs was investigated in terms of solution pH, shaking time and sorbent amount. The results have shown that most of the materials can take up REEs at a wide pH range. The experiments were continued with clinoptilolite, zeolite Y and Chelex 100 and it was demonstrated that all three materials displayed very fast kinetics for REE sorption (higher than 96% in 1 min). Desorption from the sorbents was realized with 2.0 M HNO₃ for clinoptilolite and 0.1 M HNO₃ for zeolite Y and Chelex 100. Only the lower concentration range (0.01-2.0 mg l⁻¹) of matrix-matched standards were used in quantitation although the calibration graphs were linear at least up to 10.0 mg l⁻¹ for all REEs studied. The limit of detection (3 s) without preconcentration was 0.1, 1.0, and 0.2 μg l⁻¹ for Eu, La, and Yb, respectively. The validity of the method with the selected sorbents was checked through spike recovery experiments.     

Removal and enrichment of copper ions from aqueous solution by 1,8-diaminonapthalene polymer

Microparticles of poly(1,8-diaminonapthalene) (PDAN) were prepared by chemically oxidative polymerization by (NH₄)₂S₂O₈. The effect of pH on the sorption of Cd(II), Cu(II), Ni(II), Mn(II), Zn(II) and Pb(II) on PDAN was examined by the batch procedure. PDAN showed good sorption capacity and high selectivity towards Cu(II) in comparison with the very popular chelating sorbent Chelex 100 containing iminodiacetic functional groups. The on-line preconcentration system containing the knotted reactor with the obtained polymer was examined for the sorption and desorption processes of copper ions. The applicability of this system was checked by analysis of Cu(II) content in standard reference material (NIST 1643e) and some natural water samples.     

The application of solid sorbents for the purification of aluminum contaminated chemicals used as modifiers in electrothermal atomic absorption spectrometry

Various microcolumns with solid sorbents (ion exchange resins, functionalised cellulose sorbents, chelating resins) have been tested with respect to their ability for the purification of aluminum contaminated chemicals used as modifiers in electrothermal atomic absorption spectrometry. The purification of NaNO(3), Mg(NO(3))(2), K(2)SO(4) and (NH(4))(2)HPO(4) has been the most effective with an almost 100% efficiency, when Spheron-Oxine was used as chelating resin. The sorption of aluminum from KOH solution has been found to be very high (around 90%) for all investigated sorbents. However, the best results have been obtained with anion-exchange resins. It has been difficult to purify concentrated mineral acids (HCl, H(2)SO(4)). A retention of aluminum above 80% has been achieved only when Cellex P, Chelex 100 or Amberlite XAD-2 have been used.     

Comparative study on the preconcentration of copper traces in non-saline waters with chelating resins

Summary Chelex 100, Hyphan cellulose and Amberlite IRC 718 were tested with regard to their chelation efficiency for copper traces. The retention of copper on the three chelating resins was quantitative above pH 3. Complete elution, however, from Chelex 100 and Hyphan was only possible by a mixture of HNO₃ and HCl acids. These two chelating resins were compared relevant to their preconcentration efficiency for copper traces from river and lake water samples. When employing the batch equilibration technique, sufficient recoveries were achieved for both of them. The presence of complexing agents as EDTA, NTA, sodium polyphosphate and humic acids affected the preconcentration efficiency of Chelex 100 as well as that of Hyphan. Chelex 100 seemed to be more free from EDTA and NTA interferences than the Hyphan exchanger.

---

Vergleichende Untersuchungen zur Anreicherung von Kupferspuren mit Hilfe von Chelatharzen

     

Characterization of aquatic humic substances and their metal complexes by immobilized metal-chelate affinity chromatography on iron(III)-loaded ion exchangers

The analytical fractionation of aquatic humic substances (HS) by means of immobilized metal-chelate affinity chromatography (IMAC) on metal-loaded chelating ion exchangers is described. The cellulose HYPHAN, loaded with different trivalent ions, and the chelate exchanger Chelex 100, loaded to 90% of its capacity with Fe(III), were used. The cellulose HYPHAN, loaded with 2% Fe(III), resulted in HS distribution coefficients K_d of up to 10^3.7 mL/g at pH 4.0 continuously decreasing down to 10^1.5 at pH 12, which were appropriate for HS fractionation by a pH-depending chromatographic procedure. Similar distribution coefficients K_d were obtained for HS sorption onto Fe(III)-loaded Chelex 100. On the basis of Fe-loaded HYPHAN both, a low-pressure and high-pressure IMAC technique, were developed for the fractionation of dissolved HS applying a buffer-based pH gradient for their gradual elution between pH 4.0 and 12.0. By coupling the Chelex 100 column under high-pressure conditions with an inductively coupled plasma mass spectrometer an on-line characterization of HS metal species could be achieved. Using these fractionation procedures a number of reference HS were characterized. Accordingly, the HA (humic acids) and FA (fulvic acids) studied could be discriminated into up to 6 fractions by applying cellulose HYPHAN, significantly differing in their Cu(II) complexation capacity but hardly in their substructures assessed by conventional FTIR. In the case of using Chelex 100 exchanger resin two major UV active HS fractions were obtained, which significantly differ in their complexation properties for Cu(II) and Pb(II), respectively.     

Extraction and sorption preconcentration of rare-earth elements(III) and scandium(III) with phosphorylmethyl-substituted butylphenylphosphinates from perchloric acid solutions

The interphase distribution of microamounts of La, Ce, Pr, Nd, Sm, Eu, Gd, Tb, Dy, Ho, Er, Tm, Yb, Lu, Y, and Sc perchlorates between aqueous HClO₄ solutions and solutions of bidentate phosphorylmethyl-substituted butylphenylphosphinates Oct₂P(O)CH₂P(O)Ph(OBu) (compound I) and Ph₂P(O)CH₂P(O)Ph(OBu) (compound II) in 1,2-dichloroethane is studied. The stoichiometry of extracted complexes is determined, and the efficiency of metal ion extraction into the organic phase is considered as a function of the HClO₄ concentration in the aqueous phase and the nature of the organic solvent. The possibility of concentrating rare-earth elements (REE)(III) and scandium(III) from HClO₄ solutions with the complexing sorbent synthesized by noncovalent immobilization of I and II compounds on a macroporuos polymer matrix is shown.     

CHARACTERIZATION OF CIS- AND TRANS-DINITROBIS-(l-CYCLOHEXANEDIAMINE)-COBALT(III) CHLORIDE1

Abstract

Two geometrical isomers of [Co(l-chxn)₂(No₂)₂]Cl have been isolated. The trans-isomer is eluted first from a cellulose ion exchange column as a single isomer. The cis-isomer corresponds to the complex previously reported as the trans-isomer. The cis-isomer with the same CD sign pattern as for the trans-isomer is stereoselectively favored, but a small amount of the second cis-isomer separates using Cellex CM ion exchange cellulose. The CD spectra of the cis- and trans- isomers are similar to those of the corresponding isomers of the l-pn complex.     

Amidoamine calix[4]resorcinarene-based oligomers and polymers as efficient sorbents of azo dyes from water

The sorption behaviour of three kinds of macrocyclic sorbents – amidoamine tetradodecyloxyphenylencalix[4]resorcinarene 1 and tetramethyloxyphenylencalix[4]-resorcinarene 2; composition of calix[4]resorcinarene 1+2, and novel P.1 and P.2 polymers with amidoamine calix[4]resorcinarene units towards three water-soluble azo dyes – methyl orange (MO), acid orange (AO5) and Congo red (CR) was studied. All sorbents form supramolecular complexes with the aforesaid dyes. The best sorbent for MO was shown to be polymer P.1, for the AO5 – composition 1+2 and for the CR – macrocycle 2, with high sorption capacities (373, 497 and 625 mg/g, respectively). The main factor in the binding of dyes by all studied sorbents proved to be surface electrostatic interactions. In addition to the Coulomb interactions, the most important factor for the polymers appeared to be the ‘net’ structure of the polymer with a high concentration of binding sites, providing electrostatic, hydrogen, dipole–dipole and hydrophobic interaction. Hydrophobic substituents in the sorbents exert a significant influence on the dye sorption. The increase of the sorbents' hydrophobicity leads to a lower sorption capacity for MO and CR and a higher sorption capacity for AO5. It was shown that sorption efficiency of the sorbent depends on the ‘dye–sorbent’ structure conformity.     

Chelating resins: Sorption characteristics in chloride media

The chelating resins Dowex A1 and its purified form, Chelex 100, contain the iminodiacetate functional group. The resins can exchange cations from solutions of high pH and anions from low pH solutions. Further, the iminodiacetate functional group provides chelating capability leading to special selectivity for multivalent ions such as Sb(V) and Hg(II). A systematic study of the sorption characteristics of Chelex 100 was initiated in our laboratory. Distribution coefficient values (K_d) were measured for Zn(II), Cd(II), Sn(IV), Sb(V) and Hg(II) as a function of HCl concentration and for Cu(II) and Pb(II) as a function of pH. The results obtained thus far indicate that Sb(V) and Hg(II) have high K_d values in acid chloride solutions. A radiochemical separation procedure was developed for the determination of Hg by neutron activation analysis using sorption onto Chelex 100.     

Sorption of silver ions by Chelex 100 chelating resin

Sorption of Ag⁺, Ag(NH₃) _n ⁺ , and anionic complexes of silver with chloride and thiocyanate ions by Chelex 100, a chelating resin, were investigated systematically. The results are utilized to interpret the seemingly contradictory data available in the literature     

Separation of copper(II) and aluminium(III) from fresh waters by solid phase extraction on a complexing resin column

The solid‐phase extraction (SPE) of copper(II) and aluminium(III) from fresh waters on an ion‐exchange complexing resin containing iminodiacetic groups (Chelex 100) has been examined. Quantitative recovery of the metal ions was related to the breakthrough profile that, for some samples, could not be evaluated directly. A method is suggested for evaluation, instead, of the sorption curves, on the basis of passing different volumes of sample through the column. This enables evaluation of important properties, for instance the central point of the breakthrough curve, V_f. The column used was a small one, containing 0.10 g dry Chelex 100. The metal ion was eluted with a small volume of acid solution, 10 mL of 0.5 mol L^–1 HNO₃; this resulted in good preconcentration factors. For copper(II) it was found that fresh waters of similar composition could have different V_f in the same column. This was ascribed to different reaction coefficients (α_M(I)) of copper(II) in the considered samples, which affects V_f. By use of the proposed SPE procedure it is possible to evaluate the reaction coefficient of copper(II). The values of α_M(I) for two different drinking waters at pH 7.7 were found to be 3.70×10¹² and less than 4.40×10¹¹. Similar results were obtained for aluminium(III).     

Rapid magnetic solid-phase extraction based on magnetite/silica/poly(methacrylic acid–co–ethylene glycol dimethacrylate) composite microspheres for the determination of sulfonamide in milk samples

A novel magnetic solid-phase extraction (MSPE) sorbent, magnetite/silica/poly (methacrylic acid–co-ethylene glycol dimethacrylate) (Fe₃O₄/SiO₂/P(MAA-co-EGDMA)), was developed. This MSPE material was prepared by distillation–precipitation polymerization of MAA and EGDMA in the presence of Fe₃O₄/SiO₂ microspheres with the surface containing abundant reactive double bonds. The resultant sorbent material was characterized by elemental analysis, electron microscopy, X-ray diffraction and Fourier-transformed infrared spectroscopy. In this work, eleven sulfonamides (SAs) were selected as model analytes to validate the extraction performance of this new MSPE sorbent. Noticeably, the extraction can be carried out quickly, the extraction time for the SAs onto Fe₃O₄/SiO₂/P(MAA-co-EGDMA) sorbent can be clearly shortened to 0.5 min. The desorption solution of SAs was analyzed by LC–MS/MS, and the results showed that the recoveries of these compounds were in the range of 87.6–115.6%, with relative standard deviations ranging between 0.9% and 10.8%; the limit of detection were in the range of 0.5–49.5 ng/L.     

Application of the ion-exchanger Cellex P for the selective separation of some metal ions

Summary The selectivity of the cellulose ion-exchanger Cellex P containing phosphonic groups has been examined by means of tetrene. The affinity of 14 metal ions was determined as a function of the pH-value in the presence of tetrene. Bismuth was separated from large excess of Pb, Cd, Cu, Co, Ni, Fe, Mn and Zn by means of this ion-exchanger using tetrene as a complexing agent. The method has been applied to the determination of bismuth in metallic lead.

---

Anwendung des Ionenaustauschers Cellex P zur selektiven Abtrennung einiger MetallionenTeil 3. Quantitative Abtrennung des Bismuts von anderen Elementen in Gegenwart von Tetraethylenpentamin (Tetren) als Komplexierungsmittel

Zusammenfassung Die Selektivität des Phosphonsäuregruppen-haltigen Celluloseaustauschers Cellex P wurde mit Hilfe von Tetren untersucht. Die Affinität von 14 Metallionen wurde als Funktion des pH-Wertes in Gegenwart von Tetren bestimmt. Bismut konnte von einem großen Überschuß an Pb, Cd, Cu, Co, Ni, Fe, Mn und Zn abgetrennt werden. Das Verfahren wurde zur Bismutbestimmung in Bleimetall angewendet.

     

Diffusive gradients in thin films technique for uranium measurements in river water

The diffusive gradients in thin films technique (DGT) was used for uranium measurements in water. DGT devices with Dowex resin binding phase (Dow DGT) were tested in synthetic river water, which gave 84% response to total uranium concentration. The devices were also deployed in natural river water and compared to devices with other types of binding phases, Chelex 100 resin beads imbedded in polyacrylamide hydrogel (Chelex DGT) and DE 81 anion exchange membrane (DE DGT), deployed in the same location at the same time. The measurement by Dow DGT was the lowest among the different types of the DGT devices, 45% of total uranium, while measurement by DE DGT was the highest, 98% of total uranium. The results achieved by the three types of DGT devices were explained by three DGT working mechanisms, equilibrium between complexes of resin/uranyl carbonates and complexes of resin/competitive ligands in water, effective reduction of uranyl carbonate concentration by the binding phase and dissociation of UO₂(CO₃)₂²⁻ and UO₂(CO₃)₃⁴⁻ within the diffusive layer in a DGT device. It is hoped that by deploying the DGT devices with different binding phases in natural waters, additional information on uranium speciation could be obtained.     

Performance characteristics of suspended particulate reagent-iminodiacetate as a binding agent for diffusive gradients in thin films

The performance characteristics of an alternative binding agent, suspended particulate reagent-iminodiacetate (SPR-IDA), for use with DGT methodology were investigated. The parameters investigated during this study included gel hydration, blank levels, elution factor (f_e), capacity, the effects of pH on the binding of trace metals by DGT. The novel application of this resin for use as a quantitative standard for laser ablation ICP-MS was also evaluated. To further constrain the results for the SPR-IDA binding agent, parallel experiments were performed using resin gel containing Chelex 100, which has been widely reported in the literature. Hydration results showed that the SPR-IDA resin gel reached a stable dimension and weight within ∼30 min and was dimensionally stable for ≤6 months. The measured DGT blanks for the SPR-IDA resin were 0.0023, 0.15, 0.21, 0.0033 and 0.011 ng disc⁻¹ for Co, Ni, Cu, Cd and Pb, respectively. The elution factor differed for the two resin types with the Chelex 100 recoveries slightly lower than previous reports and the SPR-IDA resin showing on average ∼5-9% better recoveries than DGT containing Chelex 100. The measured capacity of DGT discs containing the SPR-IDA binding agent was 0.26 mg Cd, similar to the calculated value of 0.29 mg Cd, indicating the entire resin layer was available for metal uptake.Both resin types performed equally well when deployed in 1 mM NaNO₃ solutions with DGT measurements of ∼100% of direct solution measurements for Co, Ni and Cd. However, DGT measurements of Cu and Pb systematically decreased with increasing solution pH down to ∼50% of solution values at pH 8.0, due to artifacts resulting from colloid formation during the addition of the metals. This was remedied by adding the metals as dilute salt standards and addition of Mg(NO₃)₂ to eliminate adsorption to the container walls. In the latter experiments, DGT measured concentrations of Co, Ni, Cu, Cd and Pb were in agreement with solution concentrations. Deployment of DGT in solutions with increasing concentrations of trace metals yielded linear results, suggesting that quantitative analysis using simplified laser ablation techniques should be possible using this newly characterized SPR-IDA resin gel.     

Preconcentration of nickel using cellulose ion exchangers for electrothermal atomic absorption spectrometric determination

Nickel (? 0.11 μg l^?1) in water samples is determined by graphite furnace atomic absorption spectrometry after preconcentration from 3 l of sample on a column of Cellex CM and elution with 20 ml of 2 M nitric acid. High concentrations of some other cations interfere, but the concentrations present in river and tap waters have no effect. The use of Cellex P is also studied.