Solid-phase reactors in sequential injection analysis. Determination of manganese(II) in tap water and effluent streams using a solid-phase lead(IV) dioxide reactor in a sequential injection system

The determination of manganese(II) in tap water and effluent streams, using a solid-phase reactor incorporated into a sequential injection system was investigated. Mn²⁺-ions in samples injected into a carrier stream, were oxidised by solid lead(IV) dioxide suspended on silica gel beads to form MnO₄ ^–-ions which were detected spectrophotometrically at 526 nm. The linear range of the system is from 1 to 7 mg L^–1 with a detection limit of 0.62 mg L^–1. The proposed system is suitable for the determination of manganese(II) in tap and effluent streams at a rate of approximately 50 samples per hour with a relative standard deviation of better than 3%. Statistical comparison between the proposed sequential injection system and a standard ICP method revealed that there is no significant difference between the two methods at the 95% confidence level for effluent streams and at 99.9% for tap water.     

An improved method for determination of 7Be in mosses

We have measured ⁷Be activity in moss samples collected from in and around Mumbai, India. The use of heavily shielded Compton suppressor system is more efficient than the conventional gamma spectroscopic system for detection of ⁷Be. The ⁷Be accumulation capacities of mosses are more than other plant samples. Therefore monitoring of young moss samples by Compton suppressor system is an excellent tool for determination of atmospheric fallout of ⁷Be. A positive bias in the high altitude samples has been observed which might be due to any of the two reasons (i) higher cosmic ray flux in the high altitude or (ii) high pollution in the lower altitude area ultimately inhibits uptake of ⁷Be.     

Determination of Cd,Hg, Pb and Se in sediments slurries by isotopic dilution calibration ICP-MS after chemical vapor generation using an on-line system or retention in an electrothermal vaporizer treated with iridium

A method for the determination of Cd, Hg, Pb and Se in sediments reference materials by slurry sampling chemical vapor generation (CVG) using isotopic dilution (ID) calibration and detection by inductively coupled plasma mass spectrometry (ICP-MS) is proposed. Two different systems were used for the investigation: an on-line flow injection system (FI-CVG-ICP-MS) and an off-line system with in situ trapping electrothermal vaporization (CVG-ETV-ICP-MS). About 100 mg of the reference material, ground to a particle size ≤50 μm, was mixed with acid solutions (aqua regia, HF and HCl) in an ultrasonic bath. The enriched isotopes ¹¹¹Cd, ¹⁹⁸Hg, ²⁰⁶Pb and ⁷⁷Se were then added to the slurry in an adequate amount in order to produce an altered isotopic ratio close to 1. For the on-line system, a standing time for the slurry of 12 h before measurement was required, while for the batch system, no standing time is needed to obtain accurate results. The conditions for the formation of the analyte vapor were optimized for the evaluated systems. The following altered isotope ratios were measured: ¹¹¹Cd/¹¹⁴Cd, ¹⁹⁸Hg/¹⁹⁹Hg, ²⁰⁶Pb/²⁰⁸Pb e ⁷⁷Se/⁸²Se. The obtained detection limits in the on-line system, in μg g⁻¹, were: Cd: 0.15; Hg: 0.09; Pb: 6.0 and Se: 0.03. Similar detection limits were obtained with the system that uses the ETV: 0.21 for Hg, 6.0 for Pb and 0.06 μg g⁻¹ for Se. No signal for Cd was obtained in this system. One estuarine, two marine and two river certified sediments were analyzed to check the accuracy. The obtained values by both systems were generally in agreement with the certified concentrations, according to the t-test for a confidence level of 95%, demonstrating that isotope equilibration was attained in the slurries submitted to a chemical vapor generation procedure and detection by ICP-MS. The relative standard deviations were lower than 10%, adequate for slurry analysis. The almost quantitative analytes extractions to the aqueous phase of the slurry must favor equilibration of the added enriched isotope with the isotope in the sample, allowing the use of isotopic dilution calibration for slurry analysis.     

Determination of Potassium Ferrocyanide in Foods by Resonance Rayleigh Scattering Method with Double-Charged Triaminotriphenylmethane Dyes

In pH 1.0 acidic medium, double-charged triaminotriphenylmethane dyes such as methyl green （MEG） and iodine green （IG） react with potassium ferrocyanide to form 2 ： 1 ion-association complexes by virtue of electrostatic forces and hydrophobic interaction. It results in the change of absorption and the great enhancement of resonance Rayleigh scattering （RRS） and the appearance of new RRS spectra. Two systems have similar spectral characteristics and their maximum RRS wavelengths are all located at 276 nm and smaller peaks are located at 332 and 457 nm, respectively. The intensity of RRS is directly proportional to the concentration of [Fe（CN）6]^4- in the range of 0.03-5.7 μg·mL^-1 （MeG system） or 0.04-5.9 μg·mL^-1 （IG system）. The RRS method has high sensitivity and the detection limit （3σ） for potassium ferrocyanide is 9.3 ng·mL^-1 （MeG system） or 11.2 ng·mL^-1 （IG system）. The optimum conditions, influencing factors and effects of foreign substances are investigated. The method also has a good selectivity. A sensitive, rapid and simple RRS method for the determination of potassium ferrocyanide in salinized food and table salt has been developed.     

A method for the determination of additive elements in sintered tungsten metal rods by fast neutron activation analysis

A non-destructive activation analytical method developed for the determination of the axial concentration distributions of Al, Si and K residual additives in sintered tungsten rods is briefly described. A 14 MeV neutron generator is used to produce the reactions²⁷Al(n, p)²⁷Mg,²⁸Si(n, p)²⁸Al and³⁹K(n, 2n)³⁸K and the activities are compared with standards. A weighted least-squares fitting program is used for peak area determination of the scintillation spectra. A scheme of the irradiating and measuring arrangement with a pneumatic sample-transfer system is presented. The system is applicable to large-scale routine analysis and lends itself well to automation. The results of preliminary measurements with this arrangement are given.     

Extractive Determination of Vanadium in Fungi Samples

A new reagent system has been reported for the extractive separation and simultaneous spectrophotometric de termination of vanadium (V). The method is based on the formation of a water in soluble blue‐violet V(V) complex with N‐hydroxy‐N‐m‐tolyl‐N′‐phenylbenzamidine (HTPBA), and neutral surfactant Triton X‐100 into chloroform over an acidity range of 1.0–10.0 M acetic acid. The complex shows a broad absorption maximum at 570 nm, when measured against a chloroform blank. The λ_max (570 nm) of the complex and that of re agent (313 nm) are well separated, hence the excess of the reagent does not interfere in the spectrophotometric de termination of the metal. The molar absorptivity (?) of the complex is (4.74) × 10³ 1 mol^?1 cm^?1. The linearity of the calibration curve is followed between 0.5–12.0 μg mL^?1 with slope, intercept and correlation coefficient of 9.16× 10^?2, 4.5 × 10^?3 and 0.999, respectively. The detection limit of the method is 45 μgl^?1. The proposed re agent system provides significantly higher tolerance limit for iron (500 μg mL^?1) and also various metalions commonly associated with vanadium did not interfere. The method was applied for the deter mi nation of vanadium content of three samples i.e. Spirogyra, Puccinia and Riccia.     

Transport Properties and Phase Behaviour in Binary and Ternary Ionic Liquid Electrolyte Systems of Interest in Lithium Batteries

A binary ionic liquid (IL) system based on a common cation, N‐methyl‐N‐propylpyrrolidinium (C₃mpyr⁺), and either bis(trifluoromethanesulfonyl)imide (NTf₂^?) or bis(fluorosulfonyl) imide (FSI^?) as the anion is explored over its entire composition range. Phase behavior, determined by DSC, shows the presence of a eutectic temperature at 247 K and composition around an anion ratio of 2:1 (FSI^?:NTf₂^?) with the phase diagram for this system proposed (under the thermal conditions used). Importantly for electrochemical devices, the single phase melting transition at the eutectic is well below ambient temperatures (247 K). To investigate the effect of such anion mixing on the lithium ion speciation, conductivity and PFG–NMR diffusion measurements were performed in both the binary IL system as well as the Li‐NTf₂‐containing ternary system. The addition of the lithium salt to the mixed IL system resulted in a decrease in conductivity, as is commonly observed in the single‐component IL systems. For a fixed lithium salt composition, both conductivity and ion diffusion have linear behaviour as a function of the anion ratio, however, the rate of change of the diffusion coefficient seems greater in the presence of lithium. From the application point of view, the addition of the FSI^? to the NTf₂^? IL results in a considerable increase in lithium ion diffusivity at room temperature and no evidence of additional complex ion behaviour.     

Batch and flow-injection determination of ethylenediamine in pharmaceutical preparations

the ethylenediamine/pyridine-2-carbaldehyde/copper(I) system is used in a new spectrophotometric method for the determination of ethylenediamine. The batch procedure involves the formation of an orange chelate between the Schiff's base and copper(I) ions at pH 8.5 (borate buffer) and measurement of the absorbances at 475 nm against water after 10/2-15 min; Beer's law is obeyed over the range 0.5/2-11.2 μg ml^?1 and the molar absorptivity is 6.21 × 10³ l mol^?1 cm^?1. Tolerance limits for different amines [36] and other organic compounds [12] are reported. In the optimized flow-injection system, ethylenediamine (1.4/2-84.6 μg ml^?1 is determined at a sample throughput of 55 h^?1. The method is sensitive and selective and is satisfactory for the determination of the diamine in aminophylline and pharmaceutical preparations (ethylenediamine contents from 0.031 to 3.23%) with relative errors ranging from ?7.4 to +11.1% and relative standard deviations of about 0.65% for both procedures.     

邻菲啰啉计算光度法同时测定生物浸出样品中Fe（Ⅱ）和Fe（Ⅲ）

邻菲哕啉光度法常用于Fe（Ⅱ）测定,但受到试样中Fe（Ⅲ）对测定的影响,因此不能直接用于生物浸出样品中Fe（Ⅱ）和Fe（Ⅲ）的同时测定．为此,基于Fe（Ⅱ）邻菲哕啉特征吸收曲线以及混合铁中Fe（Ⅲ）对Fe（Ⅱ）测定的线性影响关系,建立了基于Fe（Ⅱ）和全铁同时测定Fe（Ⅱ）和Fe（Ⅲ）的计算光度法,并研究了生物浸出样品中典型金属离子（Cu^2＋、Ni^2＋、Cd^2＋、Co^2＋）以及试样溶解与储放对测定的影响．方法可准确地测定含铁次生矿物和生物浸出液中铁价态组成,应用于生物浸出矿渣、细胞表面中常量或微量的Fe（Ⅱ）和Fe（Ⅲ）组成分析,具有简便快速的特点．     

Analysis of water-soluble fraction of metals in atmospheric aerosols using aerosol counterflow two-jets unit and chemiluminescent detection

A new analytical system for a semi-continuous analysis of water-soluble fraction of particulate metals is described. The system combines the continuous sampling of atmospheric aerosols into deionized water using the Aerosol Counterflow Two-Jets Unit and on-line chemiluminescent detection of water soluble fraction of metals in collected aerosols. The potential of analytical system was studied using Fe³⁺, Cu²⁺ and Co²⁺ as model metals in atmospheric aerosols. The detection limits of particulate Fe³⁺, Cu²⁺ and Co²⁺ (S/N?=?3) are 24, 41 and 0.4?ng?m^?3, respectively. The presented set-up allows the determination of concentration of water-soluble fraction of particulate metals in ‘real time’ with time resolution of 30?min. The system is sufficiently robust for the field application. The method has been applied to the measurement of selected metals in urban TSP (Total Suspended Particles) aerosols in Brno in the Czech Republic. The concentrations of particulate water-soluble Fe³⁺, Cu²⁺ and Co²⁺ were found in the range of 35 to 290, 42 to 462 and 0.5 to 9?ng?m^?3, respectively.     

Dissolving of cellulose in PEG/NaOH aqueous solution

Here, a new solvent system for cellulose is reported. The solvent is a mixed aqueous solution of 1.0 wt.% poly(ethylene glycol) (PEG) and 9.0 wt.% of NaOH. Cellulose powder was added into the mixture at room temperature at first, and freezing it at −15 °C for 12 h following a thaw of the mixture at room temperature under strong stirring. There formed a clean solution of cellulose, and the optical microscopy was used to record the dissolving process. ¹³C-NMR, FT-IR, XRD, and intrinsic viscosity measurements revealed that there forms a homogeneous solution of cellulose in the new solvent system. The maximum solubility of cellulose with average molecular weight of 1.32 × 10⁵ g mol⁻¹ in the solvent system is 13 wt.%. The cellulose solution in the new solvent system is stable, even for 30 days storage at room temperature.     

Integrated reaction/spectrophotometric detection in unsegmented flow systems

The use of ion-exchangers located in the flow cell of an unsegmented flow system is proposed and applied to the determination f copper(II) based on the formation of a colored chelate with 1-(2-pyridylazo)-2-naphthol retained on Dowex 50W resin. The sample solution can be injected in the normal way or pumped into the system over an interval of time dependent on the analyte concentration (preconcentration method for very dilute samples). Kinetic measurements are made along the retention curve. Copper(II) is eluted with thioglycollic acid, which makes the system reversible. The determination limit achieved is 1 ng ml^-1 and the calibration curves have good features. Depending on the conditions chosen, the sampling frequency is 10–110 h^?1.     

Improved spectrophotometric determination of paraquat in drinking waters exploiting a Multisyringe liquid core waveguide system

A novel Multisyringe flow injection analysis (MSFIA) system combined with a 200 cm long pathlength liquid core waveguide (LCW) has been developed enabling for the first time the sensitive spectrophotometric determination at μg L⁻¹ levels of the herbicide paraquat (Pq²⁺) in drinking waters. The proposed system is a simple, economic and fast alternative for obtaining the first evidence of paraquat pollution prior the use of more complex instrumental techniques.The proposed methodology is based on the production of a blue free radical by reaction of Pq²⁺ with ascorbic acid (partially oxidized with potassium iodate) in basic medium. Limits of detection and quantification as low as 0.7 and 2.3 μg L⁻¹, were obtained respectively. The working range is linear up to a concentration of 250 μg L⁻¹ of Pq²⁺. The injection throughput of the proposed method is 34 h⁻¹. The results obtained with the LCW are compared with those using a conventional 1 cm flow cell. The automation of standard addition procedures has been studied and implemented for samples causing matrix effects. Finally the proposed system has been applied to the determination of paraquat in drinking water samples.     

Beam-foil study of doubly and singly excited states in BIII

Doubly excited⁴ L and² L systems of BIII have been studied by beam-foil spectroscopy. Spectra of boron (λ: 28.7–50.1 nm) have been recorded at Bochum with a resolution superior to that obtained previously. Eight new lines are classified in the⁴ L system and one in the² L system. The wavelength accuracy of most of the transitions already reported in the core-excited systems of BIII is greatly improved. On the basis of these results, six and two unidentified lines appearing in spectra recorded at Liège (λ: 50–200 nm) are classified in the⁴ L and² L core-excited systems, respectively. Where comparison with theoretical predictions by Chung et al. [1] is possible, excellent agreement is found for all the assigned lines. The first energy values are reported for seven terms in the doubly excited quartet system. Moreover, seven new lines are identified in the singly excited system of BIII.     

The trace determination of some heavy metals in waters by flow-injection spectrophotometry and potentiometry

Three automated flow-injection systems are proposed for the determination of traces of manganese(II), lead and copper(II) in waters. The first system utilizes the catalytic effect of manganese(II) on the oxidation of N,N-diethylaniline by potassium periodate at pH 6.86–7.10 (30°C) and is used for spectrophotometric determination at 475 nm in the range 0.02–1.00 μg1^?1; the system involves reagent injection and stopped flow. The determination of lead in the range 0.7–100 μg1^?1 is based on spectrophotometric detection of the lead 4/(2-pyridylazo)resorcinol complex at 525 nm after on-line preconcentration of the sample (5–50 ml) on a minicolumn filled with Chelex-100 or Dowex 1-X8 resin. A potentiometric flow-injection system with a copper ion-selective electrode is applied for the determination of 0.5–1000 μg 1^?1 copper(II) after on-line preconcentration of 50–500 ml of sample on Chelex-100 resin. The procedures are tested on synthetic and real water samples, including sea water and waste-waters.     

Spectrophotometric Multicommutated Flow System for the Determination of Hypochlorite in Bleaching Products

Abstract

A multicommutation flow system for the spectrophotometric determination of hypochlorite in bleaching products is proposed. In this system, N,N-diethyl-p-phenylenediamine (DPD) reacts with hypochlorite, and the product was monitored at 515 nm. The analytical curve for hypochlorite was linear in the concentration range from 2.68 × 10^?5 to 1.88 × 10^?4 mol L^?1 (2–14 mg L^?1) with a detection limit of 6.84 × 10^?6 mol L^?1 (0.51 mg L^?1). The sampling rate was 45 h^?1, and a relative standard deviation of 1.4% (n = 10) was obtained. The recovery of this analyte ranged from 97.2% to 102.5%, and the results found using the proposed spectrophotometric multicommutated flow system agreed with the data obtained using a reference method (iodometric titration) at the 95% confidence level.     

Development of continuous inflow tritium measurement in water technology using electrolysis and a plastic scintillator

Our goal was to develop a mobile tritium monitor for continuous inflow system for water sample. The system is based on electrolysis and a plastic scintillator detection system. The minimum detectable activity (MDA) of the prototype system is 431 kBq L^?1, while the MDA of a commercially available product is 740 kBq L^?1. We expected to achieve a 5.73-times lower MDA by optimizing detection geometry using a multi-hydrogen-gas-channel. The system can be applied either as a mobile leakage surveying method or as a fixed-type monitor for detecting tritium in drinking water by adapting conventional background reduction technologies.     

Singlet Oxygen Luminescence Image in Blood Vessels During Vascular-Targeted Photodynamic Therapy

Singlet oxygen (¹O₂) is widely regarded as the main cytotoxic substance that induces the biological damage for photodynamic therapy (PDT). In this study, the previously developed near-infrared (NIR) optical imaging system was optimized for fast imaging of ¹O₂ luminescence. The optical imaging system enables direct imaging of ¹O₂ luminescence in blood vessels within 2 s during vascular-targeted PDT (V-PDT), which makes this system extremely practical for in vivo studies. The dependence of RB concentration on ¹O₂ luminescence image was investigated for V-PDT, and the data imply that 1270 nm signal is attributed to ¹O₂ luminescence. The imaging system operates with a field of view of 9.60 × 7.68 mm² and a spatial resolution of 30 μm, which holds the potential to elucidate the correlation between cumulative ¹O₂ luminescence and vasoconstriction for V-PDT.     

FIA-potentiometry in the sub-Nernstian response region for rapid and direct chloride assays in milk and in coconut water

A simple and reliable FIA-potentiometric system for rapid assays of chloride in certain food samples is described and evaluated. The system is constituted by an aquarium air pump to propel the carrier solution, a manually operated injector, a homemade dialysis flow cell, a solid-state chloride detector (Ag/AgCl), a reference electrode and a multimeter connected to a microcomputer for data acquisition. The dialysis unit enables direct analysis of liquid food samples without any other previous treatment. The principal novelties are the precision (R.S.D. of 1.2% for whole milk) and rapidity (90 determinations/h) of FIA measurements near and below the lower end of the linear (Nernstian) response region of the chloride ion-selective electrode (ISE), with an estimated detection limit (3 s) of 0.4 mg L⁻¹ Cl⁻ in the sample injected in donor stream. Data of peak potential versus sample chloride concentration (donor stream) was accurately fitted with a quadratic polynomial over the range between 4 and 1000 mg L⁻¹ (r² = 0.9999) and used as a calibration curve. The method was applied to the determination of chloride in milk and in coconut water samples. The validation of the results was done by comparison with a NIST reference material (milk) or by capillary electrophoresis (coconut water). For all analysis, no significant difference at a 95% confidence level was observed.     

Determination of glucose in blood by flow injection analysis and an immobilized glucose oxidase column

A flow-injection system for glucose determination is described. Glucose oxidase is immobilized on controlled porosity glass (CPG) and used in a glass column (2.5 mm diameter × 2.5 cm). The hydrogen peroxide produced by the enzymatic reaction (? 1 × 10^?6 M) is detected by the current produced in a flow-through cell, with two platinum electrodes having a potential difference of 0.6 V. Glucose (0–20 mmol l^?1) can be determined in blood plasma either with a dialyser in the system or, better, by incorporating a column of copper(II) diethyldithiocarbamate on CPG before the enzyme column. The results compared well with those obtained by a conventional analyser system. The glucose oxidase column showed little change in activity over a 10-month period.