Effect of Additive Agent on the Electrochemical Capacitance of Activated Carbon

In order to compare the effect of additive agent on the electrochemical capacitance of activated carbon, three additive agents like carbon nanotubes (CNTs), activated carbon fibre (ACF) and acetylene black (AB) were added to activated carbon by ultrasonic dispersion. Two electrodes including 95wt.% activated carbon, 2wt.% additive agent and 3wt.% PTFE binder were prepared. ECs were assembled in an argon-filled glove box by sandwiching a microporous separator (Celgard 2400) between two ele…     

碳纳米管/五氧化二钒空心球的制备及其电化学性能研究

采用溶剂热法制备了碳纳米管穿插的分级结构五氧化二钒空心球（VOC_x）. 使用XRD、SEM、循环伏安曲线和充放电曲线研究了不同碳纳米管量对产物结构、形貌和电化学性能的影响. 结果表明,碳纳米管的加入明显改善了VOC的倍率特性. 碳纳米管含量为7.1%时,0.5 A·g^-1电流密度下,其比电容达到346 F·g^-1,8 A·g^-1电流密度时,其电容保持率可达75%. 与活性炭组装成混合电容器,在功率密度为700 W·kg^-1时,能量密度达12.6 Wh·kg^-1.     

The role of carbon nanotubes on the capacitance of MnO<Subscript>2</Subscript>/CNTs

The electrochemical behavior of MnO₂/carbon nanotubes (CNTs) has been studied by using cyclic voltammetry, galvanostatic charge discharge measurement and electrochemical impedance spectroscopy in 0.5 M Na₂SO₄ solution. The loading mass of CNTs, the potential sweep rate as well as the frequency have been investigated in detail to make clear of their influence on capacitance, resistance, and relaxation time constant. The dependence of the voltammetric surface charge q* on different loading mass of CNTs and potential scan rate has been investigated. With the addition of CNTs, resistance and relaxation time constant of the material are reduced and the rate capability increased. In particular, CNTs is beneficial for the outer surface capacitance contribution of MnO₂. The outer surface capacitance contribution of MnO₂/CNTs (1: 1) can reach 67% total capacitance contribution.     

The Effect of Electrochemical and Gas Phase Activation of High Surface Area Carbon Black Ketjen Black EC 600 DJ on Its Surface Composition,Electrochemical Capacitance,and Stability

The effect of electrochemical and gas-phase activation of high-surface-area carbon black Ketjen Black EC 600 DJ on its stability and electrochemical capacitance is studied. The electrochemical activation is carried out according to the “start–stop” protocol (1–1.5 V, 0.5 V/s). The stability of samples is assessed based on variation of their effective resistance (based on the results of cyclic voltammetry (CVA)) and electrochemical capacitance (based on CVA and galvanostatic data) with the cycle number. The changes in the texture and surface properties of activated samples are studied by the methods of nitrogen low-temperature adsorption and X-ray photoelectron spectroscopy. The gas-phase activation of high-surface-area carbon black Ketjen Black EС 600 DJ is shown to impair its stability, while the electrochemical oxidation of carbonblack samples leads to a considerable (two-fold) increase in their electrochemical capacitance.     

Electrochemical Introduction of Active Sites into Super-long Carbon Nanotubes for Enhanced Capacitance

Electrochemical cyclic voltammetric(CV)scan was applied to inducing the partial oxidation and defects of carbon nanotubes(CNTs).The electrochemically induced functional groups and physical defects were...     

活化和表面改性对碳纳米管超级电容器性能的影响

用KOH为活化剂对碳纳米管（CNTs）进行活化；用浓硝酸为氧化剂对活化CNTs进行表面改性.通过TEM、BET和IR对经过活化和表面改性的CNTs进行了分析,并运用循环伏安和恒流充放电测试研究了活化和表面改性对CNTs超级电容器性能的影响.结果表明,通过活化使CNTs的比表面积增大,从而使其比电容从未活化时的43 F•g－1提高到73 F•g－1；通过表面改性引进赝电容,使电容器的比电容进一步提高到94 F•g－1.     

MoO3基纳米复合材料的制备及其电化学性能研究

以MoO3为基体,分别用超声分散法与碳纳米管(CNTs),化学原位聚合法与聚吡咯(PPy)复合,制备了MoO3/CNTs,MoO3/PPy和MoO3/CNTs/PPy纳米复合材料。利用XRD、SEM、TEM对复合材料进行物性表征,在1 mol·dm-3的HCl溶液中对MoO3,MoO3/CNTs,MoO3/PPy和MoO3/CNTs/PPy四个样品进行电化学测试。结果表明,复合材料的比容量均高于MoO3,其中,由于MoO3/PPy特殊的一维核壳结构使其具有较高的比表面积,相比较其他复合材料而言,有更好的电化学活性。该材料的最大比电容为450.8F·g-1。     

Characterization of Microporous Activated Carbon Electrodes for Electric Double-layer Capacitors

IntroductionElectric double layer capacitors( EDLCs) witha high power density can be used as memory back-up devices or electric vehicles.EDLCs store energyin the electric double layer by charge accumulationon the interface between the electrode and the elec-trolyte. In order to obtain reasonable energies andpower densities,the more suitable material forEDLCs musthave a high surface area with a signif-icant value of specific double layer capacitance,better pore size distribution and electro…     

Electrochemical capacitive properties of CNT fibers spun from vertically aligned CNT arrays

Due to their lightweight, large surface area; excellent electrical conductivity; and mechanical strength, carbon nanotube (CNT) fibers show great potentials in serving as both electrode materials and current collectors in supercapacitors. In this paper, the capacitive properties of both as-spun CNT fibers and electrochemically activated CNT fibers have been investigated using cyclic voltammetry and electrochemical impedance spectroscopy. It is found that the as-spun CNT fibers exhibit a very low specific capacitance of 2.6 F g⁻¹, but electrochemically activated CNT fibers show considerably improved specific capacitance. The electrochemical activation has been realized by cyclic scanning in a wide potential window. Different electrolytes have also been examined to validate the applicability of our carbon materials and the activation mechanism. It is believed that such an activation process can significantly improve the surface wetting of the CNT fibers by electrolyte (aqueous Na₂SO₄ solution). The cycling stability and rate-dependence of the capacitance have been studied, and the results suggest practical applications of CNT fibers in electrochemical supercapacitors.     

基于静电吸附作用制备PPy/CNTs复合材料

通过添加十二烷基苯磺酸钠(SDBS), 在碳纳米管(CNTs)表面引入具有静电吸附作用的基团, 使吡咯单体附着于CNTs表面, 然后发生化学原位聚合, 得到了由片状聚吡咯(PPy)包覆CNTs所构成的PPy/CNTs复合材料, 开辟了一条易于工业化生产制备PPy/CNTs复合材料的途径. 所得材料和CNTs借助傅立叶变换红外光谱、扫描电子显微镜、透射电子显微镜等设备进行了成分和形貌的表征; 并将所得材料组装成电化学超级电容器, 进行了电化学性能测试. 研究结果表明, 加入SDBS后, 吡咯单体能很好地吸附于CNTs表面; CNTs的应用细化了PPy的颗粒, 改善了PPy的导电性能和机械性能, 使PPy/CNTs复合材料呈现出多孔状; 其电化学容量达到101.1 F·g-1(有机电解液), 是同样制备条件下所得纯PPy电化学容量(19.0 F·g-1)的5倍多, 约是所用纯CNTs电化学容量(25.0 F·g-1)的4倍.     

Effect of removing silica in rice husk for the preparation of activated carbon for supercapacitor applications

The significant influence of silica inside rice husk in the preparation and electrochemical performances of activated carbon are investigated. The removing of silica results in high mesoporous ratio and good rate capability.     

活性炭二次活化对其电化学容量的影响

为进一步提高作为电化学超级电容器电极材料活性炭的电化学容量, 采用KOH作为二次活性剂, 将所得活性炭进行二次化学活化处理, 从而得到二次活化活性炭. 将原始活性炭材料与二次活化活性炭材料都分别经过系列处理, 组装成电化学超级电容器进行电化学性能测试. 测试结果表明, 二次活化活性炭材料的电化学容量达到145.0 F·g-1(有机电解液), 远远大于原活性炭材料的容量(45.0 F·g-1). 为研究二次活化活性炭材料电化学容量大幅提高的原因, 将这两种材料分别进行微观结构数据测试, 包括比表面积、N2吸脱附等温曲线和孔径分布. 研究结果表明, 二次活化处理大大增加了二次活化活性炭材料在孔径为2-3 nm的中孔分布, 从而证实对于有机电解液, 电极材料在2-3 nm的中孔对其电化学容量的提高具有重要意义.     

Effects of Precursors and Carbon Nanotubes on Electrochemical Properties of Electrospun Nickel Oxide Nanofibers-Based Supercapacitors

Supercapacitors have been considered as one of the main energy storage devices. Recently, electrospun nanofibers have served as promising supercapacitor electrodes because of their high surface area, high porosity, flexibility, and resistance to aggregation. Here, we investigate the effects of electrospinning parameters and nickel precursors on the nanostructure of electrospun nickel oxide (NiO), as well as on their electrochemical performance as supercapacitor electrodes. In contrast to the case of using nickel nitrate, increasing the nickel acetate molar concentration maintains the flexible fibrous sheet morphology of the as-spun sample during the polycondensation and calcination of NiO. As a result, our flexible electrode of NiO nanofibers derived from nickel acetate (NiO-A) exhibits much better electrochemical performance values than that of nickel nitrate-derived NiO. To further improve the electrochemical storage performance, we combined NiO-A nanofibers with single-walled carbon nanotubes (CNTs) as a hybrid electrode. In both half-cell and full-cell configurations, the hybrid electrode displayed a higher and steadier areal capacitance than the NiO-A nanofibers because of the synergetic effect between the NiO-A nanofibers and CNTs. Altogether, this work demonstrates the potency of the hybrid electrodes combined with the electrospun NiO-A nanofibers and CNTs for supercapacitor applications.     

提高电容性电化学储能装置能量容量的一些尝试

本文从作者所在的课题组在超级电容器和超级电容电池方向的研究内容为基础,在电极材料和装置层面综述了电容性电化学储能装置的发展. 导电聚合物和过渡金属氧化物分别与碳纳米管复合后的复合物能显著提高前两者作为电容性法拉第储能电极的电容性能. 活性炭和碳黑等一类碳材料则可作为非法拉第储能的电极材料. 通过对超级电容器正负极电容做相应的匹配调整可以提高超级电容器的最大充电电压,从而提高超级电容器的能量容量. 此外,为了与实际设备相匹配,超级电容可以以双极板的方式串联堆积,满足高电压的需求. 超级电容电池作为新一代的电容性电化学储能装置,分别由具有电容性和法拉第电荷储存原理的电极组成,具有高比功率和高比能量的特点,也是近年来的研究热点.     

Effect of graphitic structure on electrochemical ion intercalation into positive and negative electrodes

Commercially activated carbons are known for their high specific surface areas and low pack densities, thus giving a poor volumetric capacitance for supercapacitors. Here, nonporous pyrolyzed graphite oxides with high pack densities and controllable graphitic structures were prepared through a facile oxidation-heat treatment. XRD, Raman, SEM, and TEM were used to characterize the textural properties and morphologies of these materials. Galvanostatic charge–discharge and cyclic voltammetry revealed that the voltage-driven electrochemical ion intercalation process is, in fact, highly dependent on the graphitic structure. Less graphitized materials with larger interlayer spacings are more easily electrochemically activated, while a more rigid graphitic structure proves to be more difficult. After adequate electrochemical activation, abundant ion-accessible sites were created for charge storage, and the cell-specific capacitance dramatically increased from 3.5 to 23 F/g. The intercalation behaviors of TEA⁺ and BF₄ ^? were separately studied. The results revealed that, due to its smaller anion size, BF₄ ^? displayed superior intercalation capability as well as higher specific capacitance on the positively polarized electrode after electrochemical activation. Therefore, through optimizing the graphitic structure and the EA conditions, a high volumetric capacitance can be achieved.     

有限域聚合法制备碳纳米管-聚苯胺复合材料及其电化学性能

通过有限域聚合法将聚苯胺(PANI)均匀地生长在碳纳米管(CNTs)表面, 得到CNTs-PANI纳米复合材料. 通过透射电子显微镜(TEM)、扫描电子显微镜(SEM)、傅立叶变换红外(FTIR)光谱对样品的形貌及成分进行表征. 将得到的复合材料组装成电化学超级电容器, 进行电化学的循环伏安和恒流充放电测试. 结果显示, 运用此有限域聚合法所制备的复合材料中PANI 可以非常均匀地包裹在CNTs表面, 复合材料的比容量可以达到117.7 F·g-1(有机电解液), 远远高于所用纯碳纳米管(25.0 F·g-1)和纯聚苯胺(65.0 F·g-1)的比容量, 从而表明有限域聚合法是一良好的纳米复合材料的制备方法.     

Carbon Nanotubes Based Nanoelectrode Arrays: Fabrication,Evaluation, and Application in Voltammetric Analysis

Fabrication, electrochemical characterization, and applications of low‐site density carbon nanotubes based nanoelectrode arrays (CNTs‐NEAs) are reported in this work. Spin‐coating of an epoxy resin provides a new way to create the electrode passivation layer effectively reducing electrode capacitance and current leakage. Cyclic voltammetry showed the sigmoidal shape curves with low capacitive current and scan‐rate‐independent limiting current. Square‐wave voltammetry showed well‐defined peak shapes in voltammograms of K₃Fe(CN)₆ and 4‐acetamidophenol (acetaminophen) and the peak currents to be proportioned to their concentrations, demonstrating the feasibility for voltammetric analysis of the CNTs‐NEAs. The CNTs‐NEAs were also used successfully for voltammetric detection of trace concentrations of lead(II) at ppb level at first‐time. The CNTs‐NEAs provide an excellent platform for ultra sensitive electrochemical sensors for chemical and biological sensing.     

含磷活性炭作为双电层电容器电极材料的电化学性能

采用磷酸活化和磷酸改性制备了不同种类的含磷活性炭,采用元素分析、X射线光电子能谱(XPS)和氮气吸附等手段分析了活性炭的元素含量、表面化学性质和孔隙结构,采用恒电流充放电、循环伏安和交流阻抗分别考察了活性炭在KOH和H₂SO₄电解质溶液中作为超级电容器电极材料的电化学性能,采用自由截距多元线性回归拟合统计分析研究了活性炭电极比电容量的影响因素,应用三电极体系分析了磷元素对活性炭电化学性能的影响机理。研究结果表明,活性炭掺杂的磷引入了赝电容,提高了活性炭电极的比电容量,磷元素含量为5.88%(w)的活性炭的比电容量在0.1 A·g^-1下达到185 F·g^-1。统计分析结果显示,活性炭的中孔有利于电解质离子向微孔内的扩散。在6 mol·L^-1 KOH电解质溶液中,孔径在1.10-1.61 nm、2.12-2.43nm及3.94-4.37 nm范围内是电解质离子在活性炭孔隙内部形成双电层的主要场所;在1 mol·L^-1 H₂SO₄电解质溶液中,孔径在0.67-0.72 nm范围内有利于双电层电容的形成。     

碳纳米管在室温熔盐中的电容特性

研究了碳纳米管在室温熔盐二(三氟甲基磺酸酰)亚胺锂(LiTFSI)-乙酰胺中的电容特性. 将碳纳米管制成薄膜电极, 以LiTFSI-乙酰胺为电解液, 装配成模拟电容器, 用循环伏安和恒流充放电法研究其电化学性能. 结果表明, 碳纳米管在室温熔盐中表现出典型的电容特性, 其比电容为22 F•g^-1, 模拟电容器的工作电压可达2.0 V, 具有非常好的循环性能, 循环充放电1000次后容量损失仅10%, 表明室温熔盐是超级电容器非常有前景的新型电解液.     

Activated carbon/graphene composites with high-rate performance as electrode materials for electrochemical capacitors

Glucose-derived activated carbon (GAC)/reduced graphene oxide (RGO) composites are prepared by pre-carbonization of the precursors (aqueous mixture of glucose and graphene oxide) and KOH activation of the pyrolysis products. The effect of the mass ratio of graphene oxide (GO) in the precursor on the electrochemical performance of GAC/RGO composites as electrode materials for electrochemical capacitors is investigated. It is found that the thermally reduced graphene oxide sheets serves as a wrinkled carrier to support the activated carbon particles after activation. The pore size distribution and surface area are depended on the mass ratio of GO. Besides, the rate capability of GAC is improved by the introduction of GO in the precursor. The highest specific capacitance of 334 F g^?1 is achieved for the GAC/RGO composite prepared from the precursor with a GO mass ratio of 3 %.