Inductively Coupled Plasma Zoom–Time-of-Flight Mass Spectrometry

A zoom–time-of-flight mass spectrometer has been coupled to an inductively coupled plasma (ICP) ionization source. Zoom–time-of-flight mass spectrometry (zoom-TOFMS) combines two complementary types of velocity-based mass separation. Specifically, zoom-TOFMS alternates between conventional, constant-energy acceleration (CEA) TOFMS and energy-focused, constant-momentum acceleration (CMA) (zoom) TOFMS. The CMA mode provides a mass-resolution enhancement of 1.5-1.7× over CEA-TOFMS in the current, 35-cm ICP-zoom-TOFMS instrument geometry. The maximum resolving power (full-width at half-maximum) for the ICP-zoom-TOFMS instrument is 1200 for CEA-TOFMS and 1900 for CMA-TOFMS. The CMA mode yields detection limits of between 0.02 and 0.8 ppt, depending upon the repetition rate and integration time—compared with single ppt detection limits for CEA-TOFMS. Isotope-ratio precision is shot-noise limited at approximately 0.2% relative-standard deviation (RSD) for both CEA- and CMA-TOFMS at a 10 kHz repetition rate and an integration time of 3–5 min. When the repetition rate is increased to 43.5 kHz for CMA, the shot-noise limited, zoom-mode isotope-ratio precision is improved to 0.09% RSD for the same integration time.

Open image in new window

Graphical Abstract ?

     

Analysis of Niobium–Rare-Earth Ores by Inductively Coupled Plasma Mass Spectrometry

To determine the composition of niobium–rare-earth ores by atomic emission spectrometry and inductively coupled plasma mass spectrometry, two procedures are developed for sample preparation based on autoclave decomposition and flux fusion. Autoclave decomposition is carried out in a mixture of HF and HNO₃ at a temperature of up to 220°C and a pressure of up to 160 atm using a developed system with resistive heating. Subsequent evaporation to dry salts ensures the removal of F^– ions and silicon as SiF₄. The residue is dissolved in a mixture of HCl and H₂O₂ at 160°C under elevated pressure. The resulting solutions (10% with respect to HCl with the addition of H₂O₂) are diluted before measurements. The dissolution process is monitored for each sample using stable highly enriched isotopes of ⁹¹Zr, ¹⁰⁰Mo, ¹⁴⁹Sm, and ¹⁷⁸Hf. The second procedure is based on fusing samples with a mixture of Na₂CO₃ and Na₂B₄O₇ at 1050°C in a muffle furnace and dissolving the resulting melt in a mixture of HCl and H₂O₂. The procedures were tested using the national (NFS-23) and foreign standard samples of composition (OREAS-462, 463, 464, 465, Australia) and real samples of niobium–rare-earth ores.     

Elemental Analysis of Phytotherapeutic Products by Inductively Coupled Plasma–Tandem Mass Spectrometry

A procedure for the determination of As, Cd, Cr, Ni, Pb, and V in phytotherapy medicines by inductively coupled plasma–tandem mass spectrometry is reported. The use of tandem mass spectrometry with oxygen into an octopole reaction system at various gas flow rates and the combination of on-mass and mass-shift modes was evaluated. Cadmium, Cr, Ni, and Pb were determined as free atomic ions while As and V were determined as the oxides AsO⁺ and VO⁺ in the same run. Samples were prepared by microwave-assisted digestion with dilute nitric acid and hydrogen peroxide. Two plant-certified reference materials (apple leaves and tomato leaves) were used to check the accuracy. For tandem mass spectrometry with 0.5?mL min^?1 O₂, recoveries in the 85–113% were typically obtained and no statistical differences were observed at the 95% confidence level (t-test) in comparison with the certified values. Using these conditions, the limits of detection for the method were 0.01, 0.0002, 0.008, 0.008, 0.003, and 0.002?µg g^?1 for As, Cd, Cr, Ni, Pb, and V, respectively. The procedure was used for the analysis of four phytotherapic drugs and the determined concentrations were up to 0.168?µg g^?1 As, 0.03?µg g^?1 Cd, 0.82?µg g^?1 Cr, 1.18?µg g^?1 Ni, 0.52?µg g^?1 Pb, and 2.4?µg g^?1 V with average precision values of 8% as the relative standard deviation. The found concentrations were compared with limits proposed in official guidelines and, in most cases, the values were below the maximum limits allowed.     

Simulation of Gas-Dynamic and Thermal Processes in Vortex-Stabilized,Inductively Coupled Argon–Hydrogen Plasma

The flow of vortex-stabilized argon–hydrogen plasma in a radiofrequency induction (RFI) plasma torch has been investigated using modern methods of computational fluid dynamics. Optimal values of the torch power and energy release in plasma have been found at various argon to hydrogen ratios in the plasma gas mixture. The heat and kinetic fields determined by calculation for a plasma-chemical reactor can be of use in designing an RFI plasma torch in part concerning the determination of the optimum zone for feeding the reactants to the reactor.     

Rapid Speciation of Lead in Water by High-Performance Liquid Chromatography–Inductively Coupled Plasma Mass Spectrometry

The rapid speciation of lead is reported by high performance liquid chromatography and inductively coupled plasma – mass spectrometry. The separation of inorganic lead, trimethyllead, triethyllead and triphenyllead was achieved within 3.5 minutes on a C₁₈ column using a gradient program of methanol and water containing 5 milligrams per liter sodium 1-pentanesulfonate at pH 5. The limits of detection for inorganic lead, trimethyllead, triethyllead, and triphenyllead were 0.01, 0.02, 0.02, and 0.02 micrograms per liter, respectively. The accuracy of the method was verified by the analysis of water (GSBZ 50009-88) and seawater (GBW (E) 080040) certified reference materials. The method was also employed for the analysis of water samples; inorganic lead was measured in river water.     

Speciation of Mercury in Terrestrial Plants Using Vapor Generation and Liquid Chromatography–Inductively Coupled Plasma Mass Spectrometry

A sensitive method for mercury speciation in biological samples is reported. A simple vapor generation apparatus was coupled to liquid chromatography and inductively coupled plasma–mass spectrometry (ICP–MS) to achieve a substantial increase in sensitivity. Mercury(II) and methylmercury were separated by reversed-phase chromatography as thiolate compounds with 2-mercaptoethanol. A short reverse phase column with an octylated stationary phase (75 × 4 millimeters) was used with a mobile phase containing 0.02 mole per liter ammonium acetate, 0.2 percent (v/v) 2-mercaptoethanol, and 1 percent methanol. The effluent was mixed with hydrochloric acid (0.06 mole per liter) containing platinum (40 micrograms per liter) as the internal standard and bismuth (30 micrograms per liter) as a modifying agent followed by sodium borohydride (0.016 mole per liter). The generated volatile species were introduced into the ICP–MS by conventional solution nebulization. In addition to the sensitivity enhancement induced by vapor generation, the addition of bismuth further increased the methylmercury signal with a reduced increase in the mercury(II) signal. As a result, comparable but unequal signals were achieved: the mercury(II) signal was approximately 1.6-fold higher than the methylmercury signal. Extraction with a hydrochloric acid-2-mercaptoethanol solution was used for sample preparation. The accuracy of determination was verified using two standard reference materials and an interlaboratory reference material based on barley grown hydroponically in mercury-contaminated solution. The method was employed for mercury speciation of plant samples from a polluted region.     

Controlled Synthesis of β-SiC Nanopowders with Variable Stoichiometry Using Inductively Coupled Plasma

In the growing field of nanomaterials, SiC nanoparticles arouse interest for numerous applications. The inductively coupled plasma (ICP) technique allows obtaining large amount of SiC nanopowders from cheap coarse SiC powders. In this paper, the effects on the SiC structure of the process pressure, the plasma gas composition, and the precursor nature are addressed. The powders were characterized by X-ray diffraction (XRD), Raman and fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and high resolution electron microscopy (HREM), chemical analyses, BET and photon correlation spectroscopy (PCS) measurements. Whatever the precursor (α- or β-SiC), the nanoparticles were crystallised in the cubic β-SiC phase, with average sizes in the 20–40 nm range. Few residual grains of precursor were observed, and the decarburization due to the reductive Ar–H₂ plasma lead to the appearance of Si nanograins. The stoichiometry of the final product was found to be controllable by the process pressure and the addition of methane.     

Determination of Essential and Toxic Elements in Tropical Fruit by Microwave-Assisted Digestion and Inductively Coupled Plasma–Mass Spectrometry

The concentrations of eight essential (Co, Cr, Cu, Mn, Ni, Se, V, and Zn) and five toxic elements (Al, As, Cd, Hg, and Pb) were determined in 457 samples of commonly consumed fresh tropical fruit including bananas (Musa acuminata), kiwi (Actinidia deliciosa), mangos (Mangifera indica), and pineapple (Ananas comosus) from supermarkets from Seoul, Busan, Gangneung, Daegu, Daejeon, and Gwangju, South Korea. The samples were digested by microwave-assisted combustion using HNO₃ and H₂O₂ and determined by inductively coupled plasma mass spectrometry. The Hg concentrations were evaluated by furnace-gold amalgamation direct mercury analysis. The techniques were validated by linearity, limits of detection and quantification, precision, recovery, and the analysis of a NIST-1570a spinach leaves certified reference material. The concentrations of essential elements varied considerably among the tropical fruit. Overall, the tropical fruit was higher in Mn (0.027–13.2?µg/g) and Zn (0.514–2.20?µg/g), while lower in Co (0.002–0.005?µg/g) and V (0.001–0.002?µg/g). The concentrations (µg/g) of toxic elements were 0.001 (kiwi) to 0.003 (mango) for As and Cd, 0.0004 (pineapple) to 0.002 (banana) for Hg, and 0.005 (kiwi) to 0.013 (mango) for Pb. The calculated values of estimated dietary intake, target hazard quotients and hazard indices were lower than one and the safety limits established by World Health Organization. The tropical fruits were therefore safe and did not pose any threat to consumers.     

Trace Determination of Manganese in Urine by Graphite Furnace Atomic Absorption Spectrometry and Inductively Coupled Plasma–Mass Spectrometry

This paper describes a simple and sensitive method for the determination of manganese in human urine by graphite furnace atomic absorption spectroscopy (GFAAS), which includes sample preparation by microwave digestion. Matrix modifier combinations, the digestion power, pyrolysis, and atomization temperatures were optimized. A mixture of 5.0 µg Pd(NO₃)₂ and 3.2 µg Mg(NO₃)₂ modifier presented the best performance. The optimal temperatures for pyrolysis and atomization were 1500°C and 1950°C, respectively. The GFAAS method was compared to inductively coupled plasma–mass spectrometry (ICP–MS) for the determination of manganese in urine. Analytical figures of merit for GFAAS and ICP–MS were: accuracy (3.46%, 2.19%), precision (3.61%, 5.84%), LOD (0.109 µg · L^?1, 0.015 µg · L^?1), LOQ (0.327 µg · L^?1, 0.045 µg · L^?1), and recovery (80–100%, 74–89%). Both methods were employed for the determination of Mn in urine and the results were compared statistically.     

Determination of Phosphorus in Crude Oil and Middle Distillate Petroleum Products by Inductively Coupled Plasma–Optical Emission Spectrometry

A method for the precise and accurate determination of phosphorus in crude oil and middle distillate petroleum products was developed using inductively coupled plasma–optical emission spectrometry to rapidly determine phosphorus as a control method. The presence of phosphorus is undesirable in petrochemical products as it complexes with other metals generating residues that interrupt normal operation of refineries. The presence of phosphorus may be due to some anti-fouling additives or the crude oils processed. Consequently, it is necessary to control the phosphorus present at trace levels in the crude oil and in process streams that present various densities and viscosities. The instrumental power, nebulizer flow, pump rate, read time, and the sample preparation conditions were optimized. The desired level of quantification for the petrochemical industry was achieved allowing the simultaneous analysis of diverse liquid petroleum products.     

Multielement Analysis of South Serbian Strawberry Cultivars by Inductively Coupled Plasma—Optical Emission Spectrometry

The contents of 17 elements in thirteen strawberry cultivars grown in the five districts of Southern Serbia were determined using inductively coupled plasma optical emission spectrometry (ICP-OES). The most abundant elements are K (875–1148 mg?·?kg^?1 fresh weight), P (307–664 mg?·?kg^?1 fresh weight), Ca (192–256 mg?·?kg^?1 fresh weight), and Mg (111–189 mg?·?kg^?1 fresh weight) in all samples. Strawberries were also found to be a good source of Sr (8.05–18.6 mg?·?kg^?1 fresh weight) and Fe (3.09–10.4 mg?·?kg^?1 fresh weight). The contents of As and Cd were below the detection limit (0.0828 mg?·?kg^?1 and 0.0205 mg?·?kg^?1, respectively) in all strawberry samples, while the contents of Ni, Cr, and Cu were below the recommended tolerable levels proposed by Joint Food and Agriculture Organization of the United Nations and World Health Organization Expert Committee on Food Additives, and did not a pose a health risk for the consumer. The application of Duncan’s test showed significant differences between contents of analyzed elements in all strawberry cultivars. The highest mean levels of analyzed elements were detected in strawberries grown in the Topli?ki, Jablani?ki, and P?injski districts. The spike recovery test was used to verify the accuracy of the method, and the spike recovery was in the range 93.8–107.8%. The contents of the metals in strawberry samples were also comparable with values previously reported in the literature.     

Determination of Organotin Compounds in Wine by Microwave-Assisted Extraction and High Performance Liquid Chromatography–Inductively Coupled Plasma Mass Spectrometry

A new analytical procedure for the determination of five organotin compounds in several matrix wine samples is reported. The organotin compounds were extracted by microwave-assisted extraction with n-hexane. Extraction conditions, such as volume of n-hexane required, extraction temperature, and extraction time, were investigated and optimized by an orthogonal array experimental design. The determination of organotin compounds in the final extracts was carried out by liquid chromatography–inductively coupled plasma mass spectrometry. The procedure showed limits of detection between 0.029–0.049 µg · L^?1. The linearity was in the range of 0.5 to 100 µg · L^?1. The precision expressed as relative standard deviation (RSD) was below 9.43%. The developed method was successfully employed to analyze different matrix wine samples, and some analytes were detected at the level of 0.053 to 1.14 µg · L^?1.     

Speciation of Volatile Selenium Species in Plants Using Gas Chromatography/Inductively Coupled Plasma Mass Spectrometry

 Gas chromatography/inductively coupled plasma mass spectrometry (GC/ICP MS) coupled with solid phase micro extraction can provide a simple, extremely selective and sensitive technique for the analysis of volatile sulfur and selenium compounds in the hea     

Laser Ablation Inductively Coupled Plasma Mass Spectrometry (LA-ICP-MS) of ZnS 1−x Se x Semiconductor Materials

Luminous zinc sulphide selenide crystals (ZnS_1–xSe_x) with an anion-gradient in the µm-range within the crystal were quantitatively investigated by LA-ICP-MS. Reference standard crystals were synthesized by chemical vapour transport reaction and characterized by µ-XRF, SEM, PIXE, RBS and solution ICP-MS. Values from several analytical methods were then combined to describe the concentration in the reference crystals. Using these crystals, calibration curves with high correlation coefficients could be obtained for laser ablation ICP-MS determination of elemental concentrations. The gradient determined afterwards in the zinc sulphide selenide sample crystals was in the order of 30wt% in Se-content within an 800µm distance. This shows the promising capabilities of LA-ICP-MS in the field of elemental quantification in the µm-range.     

Studies on Volatilization of Zirconium from Electrothermal Graphite Furnace for Sample Introduction into Inductively Coupled Plasma

Element zirconium reacted with polytetrafluoroethylene (PTFE) dispersed in isopropanol-water mixture to form volatile fluoride when heated in an electrothermal graphite furnace, and the fluorides formed subsequently were vaporized into ICP for atomization and excitation. The technique provides a picogram detectkm limit and adequate precision of 4% relative standard deviation. Linear dynamic range covers over three orders of magnitude. The process of sample preparation it very convenient. It is expected that the method proposed is suitable for determination of other refractory elements.     

Matrix Effects and Behaviors of Elements in Oxalic Acid Medium by Inductively Coupled Plasma Mass Spectrometry

Because of its high sensitivity, wide dynamic range and relative freedom from interferences, inductively coupled plasma mass spectrometry (ICP-MS) has been developed for the determination of trace and ultra-trace levels of elements in various fields1. Due…     

Determination of the Mercury Isotopic Ratio by Cold Vapor Generation Sector Field–Inductively Coupled Plasma–Mass Spectrometry Using Lead as the Internal Standard

Lead was applied as an internal standard for the determination of Hg isotopic ratios. Cold vapor generation (CV) coupled with sector field–inductively coupled plasma–mass spectrometry (CV-SF-ICP-MS) was used for determination of Hg. It was effective to avoid interferences of Pb from samples while improving the sensitivity of Hg isotopic analysis by an approximate factor of 45 times higher than the aerosol mode. CV-SF-ICP-MS system was constructed and operational parameters were optimized. Research showed that the long stability of the system was limited by SF-ICP-MS and had no relationship with CV under the optimized conditions. The optimized precision of Hg isotopic ratio analysis was approximately 0.1% during 4?h. Five models were applied for the mass bias correction and the Baxter model obtained the smallest relative difference, 0.52‰. The results showed that the mean value of NIST SRM 3133 Hg isotopic ratios obtained by Pb internal standard was nearly identical with the value for Tl. The same performance was also obtained in two environmental reference materials. The results show that Pb may be used as the internal standard for determination of Hg isotopic ratio instead of Tl.     

Possibilities of the Determination of Matrix Elements of High-Purity Glasses of As–Se and As–S Systems by Inductively Coupled Plasma Atomic Emission Spectrometry

Possibilities of inductively coupled plasma atomic emission spectrometry (ICP AES) as an alternative to X-ray spectrochemical analysis are estimated in the determination of matrix elements of glasses of As–Se and As–S systems. Standard solutions were prepared from pure elements As, Se and S. It was shown that the matrix elements of glasses can be determined with an expanded uncertainty of 0.05–0.1 mol %. The results of determinations by ICP AES and X-ray fluorescence spectrometry were compared; and it was found that by the attained performance characteristics, the results of ICP AES are highly competitive with the data of X-ray fluorescence spectrometry, but do not require sets of adequate solid reference samples.     

Analytical Method Validation and Determination of Iron and Phosphorus in Vegetable Oil by Inductively Coupled Plasma–Mass Spectrometry with Microwave Assisted Digestion

Inductively coupled plasma–mass spectrometric determination of iron and phosphorus in three vegetable oils (soybean, coconut, and sunflower) was validated for the intermediate precision, trueness, linearity, and quantitation limit. The overall precision (n?=?5) for the analytes, which were above the method’s practical limit of quantification, were less than 2% relative standard deviation and the same as the laboratory control, NIST-SRM-1849a. Trueness was demonstrated with spike recoveries of the analytes in all vegetable oils at limit of quantification-level spiking. Although good linearity (regression coefficient greater than 0.9990) obtained, the recovery of phosphorus (156–189%) was high, possibly due to oil matrix enhancement, compared to the recovery of iron (91–106%). For soybean oil, sunflower oil, coconut oil, and medium chain triglycerides, the concentrations (mg/kg) of iron were in the range of 0.10–1.47, 0.09–1.51, 0.20–0.35, and 0.09–0.13, respectively. Similarly, phosphorus concentrations (mg/kg) were in the range of 0.77–124.56, 0.49–125.57, 0.52–9.72, and 0.85–11.90, respectively. The study achieved considerably low instrument-based practical limits of quantification for iron (0.005?mg/kg) and phosphorus (0.05?mg/kg), which are fivefold lower than the AOAC Official Method 2015.06. The high instrument sensitivity and selectivity of the method allow the determination of trace levels of iron and phosphorus in vegetable oils with good precision and trueness.