Determination of Chloramphenicol Residues in Foods by ELISA and LC-MS/MS Coupled with Molecularly Imprinted Solid Phase Extraction

The combination of molecularly imprinted solid-phase extraction (MISPE) with ELISA and LC-MS/MS was developed for the detection of chloramphenicol (CAP) in honey samples. Significant recoveries of 99.1 ± 7.1 and 98.8 ± 8.2% were obtained for intra- and inter-assay determination by ELISA determination, respectively. The limit of detection of CAP was 0.034 μg kg^?1 and the limit of quantification was 0.046 μg kg^?1. Determination and validation of CAP by using LC-MS/MS were performed following the same extraction and purification process as for the ELISA. The results demonstrated that the CAP samples purified by using MISPE were simultaneously applicable to analysis by ELISA and LC-MS/MS.     

Determination of 24 pesticides residues in mineral and peat soils by modified QuEChERS method and gas chromatography

A simple extraction and cleanup procedure has been developed for the analysis of 24 organophosphorus (OP), organochlorine (OC) and pyrethroid (PY) pesticides in mineral and peat soils using modified QuEChERS method. The pesticides were extracted from the soil with acidified acetonitrile. The water was removed from the extract by salting out with sodium chloride and addition of magnesium sulfate. For OP pesticides, the extracts were cleaned up with 0.2 g of primary secondary amine packed in glass Pasteur pipette and determined by gas chromatography with flame photometric detector. For OC and PY pesticides, the extracts were cleaned up with 0.2 g of silica gel packed in a glass Pasteur pipette and determined by gas chromatography with electron capture detector. After the cleanup, the extracts had lower colour intensity and reduced matrix interferences. The recovery of the OP and OC pesticides for mineral and peat soils determined at 0.01–1.0 mg kg^?1 fortification levels ranged from 79.0–120.0% and 82.2–117.6%, respectively. The detection limits for OP and OC pesticides were 0.001–0.01 and 0.002–0.005 mg kg^?1, respectively. The recovery of the PY pesticides ranged from 87.5–111.7% at the detection limits of 0.002–0.010 mg kg^?1. The relative standard deviations for all pesticides studied were below 10.8%. The modified method was simple, fast, and had utilized less reagents than the conventional methods. The method was applied to the determination of the pesticide residues in mineral and peat soil samples collected from the vegetable farms.     

Simultaneous Analysis of Hexaconazole, Myclobutanil, and Tebuconazole Residues in Apples and Soil by SPE Clean-Up and GC with Nitrogen–Phosphorus Detection

A facile and sensitive method utilizing capillary gas chromatography with nitrogen phosphorus detection (GC–NPD) has been developed and validated for simultaneous analysis of hexaconazole, myclobutanil, and tebuconazole, three broad-spectrum systemic fungicides, in apples and soil. Two samples were fortified with the three pesticides and subjected to ultrasonic extraction, followed by solid-phase extraction (SPE) to remove coextractives, before analysis by GC–NPD. SPE procedures were performed on PSA cartridges (500 mg, 3 mL), the analytes being eluted with n-hexane–acetone (9:1 v/v, 2 mL). Recovery of three pesticides from the fortified apple and soil samples ranged from 94.5 to 107.3% with relative standard deviations less than 9.7% at the three spike levels (0.01, 0.1, and 0.5 mg kg^?1). Limits of quantification of the method for apple and soil were 0.01 mg kg^?1, sufficiently below the maximum residue limits. Direct confirmation of the analytes in samples was achieved by gas chromatography–mass spectrometry (GC–MS).     

A Multiresidue Method for Simultaneous Determination of 116 Pesticides in <Emphasis Type="Italic">Notoginseng Radix et Rhizoma</Emphasis> Using Modified QuEChERS Coupled with Gas Chromatography Tandem Mass Spectrometry and Census 180 Batches of Sample from Yunnan Province

A method was established for the simultaneous determination of 116 pesticide residues in Notoginseng Radix et Rhizome with a combination of the modified QuEChERS method and GC–MS/MS. The sample was extracted with acetonitrile, cleaned up by primary–secondary amine and octadecyl-modified silica (C18) sorbents and determined by GC–MS/MS in multireaction monitoring mode. Matrix-matched calibration coupled with internal standard method was applied to compensate for the matrix effect and to quantify the pesticides. The results of all the 116 pesticides showed good linearity in the respective linear range with correlation coefficients (r²) > 0.99. The method limits of quantification were between 0.01 and 0.05 mg kg^?1. The recoveries were between 64.3 and 119.4%, with RSD values typically lower than 18.3% at three spiked levels of 0.05, 0.10 and 0.20 mg kg^?1. The validated methodology is easy, fast, highly accurate, reliable and sensitive for monitoring and quantification of the 116 pesticide residues in Notoginseng Radix et Rhizoma. In 180 batches of real samples, 11 pesticides were detected and among these quintozene and cyfluthrin were in excess of the standard of European Union maximum residue level for herbs.     

Determination of Organophosphorus Pesticides in Vegetables by GC with Pulsed Flame-Photometric Detection, and Confirmation by MS

The suitability of gas chromatography with pulsed flame-photometric detection (GC–PFPD) for determination of 24 organophosphorus (OP) pesticides in vegetables has been assessed. Pesticides were extracted with dichloromethane and analyzed without cleanup. The performance of the method was fit for purpose; recovery was between 73 and 110% and precision was better than 15%. Calculated lower limits of detection were typically <0.01 mg kg^?1, much lower than the maximum residue levels stipulated by European legislation. Three pesticides were detected in vegetable samples. Their presence was confirmed by GC with tandem mass spectrometric detection (GC–MS–MS).     

Determination of Pesticides Adsorbed on Arthropods and Gastropods by a Micro-QuEChERS Approach and GC–MS/MS

A miniaturized QuEChERS (Quick, Easy, Cheap, Effective, Rugged, and Save) approach combined with gas chromatography–tandem mass spectrometry (GC–MS/MS) has been developed for the simultaneous determination of nine pesticides (Cyflufenamide, Difenoconazole, Dimethomorph, Fluopicolide, Fluopyram, Metrafenone, Myclobutanil, Quinoxyfen, and Tebuconazole) in insects, snails, and spiders. In contrast to the original QuEChERS approach, only 500 mg of dried and homogenized sample matrix, mixed with 1.0 mL ethyl acetate and 250 mg MgSO₄:NaCl (4:1), is required for this novel “micro-QuEChERS” protocol. The organic phase was cleaned using dispersive solid-phase extraction (dSPE) with 75 mg MgSO₄:PSA sorbent (4:1). The method was validated according to SANCO/12571/2013 and applied to real samples (n = 7). Fluopicolide was the only detectable pesticide in real samples from vineyards. In two samples, the Fluopicolide levels were between the determined LOD and LOQ (0.15–1.00 mg kg^?1), and in one sample a concentration of 1.68 mg kg^?1 was detected.     

Dissipation rates of saisentong residues in fresh tobacco,tobacco powder and soil determined by high-performance liquid chromatography coupled with diode array detection

Two independent field trials were performed in Guizhou and Hunan, China in 2013 to investigate the dissipation and residue levels of saisentong in tobacco and soil. A novel and accurate method using high-performance liquid chromatography with diode array detection was developed and validated to determine saisentong levels in tobacco and soil. The average recovery of saisentong at fortification levels of 0.5, 2.5, 5.0 and 50.0 mg kg^?1 in fresh tobacco ranged from 75.92 to 107.40% with a relative standard deviation (RSD) of 0.94 to 7.55%, that at fortification levels of 0.5, 2.0 and 5.0 mg kg^?1 in tobacco powder ranged from 74.96 to 94.43% with a relative standard deviation (RSD) of 4.38 to 8.14%, and that at fortification levels of 0.1, 0.5 and 5.0 mg kg^?1 in soil ranged from 86.90 to 100.0% with an RSD of 1.38 to 4.62%. The limit of detection (LOD) of saisentong was 0.15 mg?kg^?1 in tobacco and 0.03 mg kg^?1 in soil, and the limit of quantification (LOQ) was 0.5 mg kg^?1 in tobacco and 0.1 mg kg^?1 in soil, respectively. For field experiments, the half-lives of saisentong in tobacco from Guizhou and Hunan were 5.9 and 1.6 days, respectively; those in soil were 14.7 and 12.0 days, respectively. The results suggest that the saisentong dissipation curves followed the first-order kinetic. The terminal residues of saisengtong in tobacco ranged from 0.5 to 9.39 mg kg^?1 at pre-harvest intervals (PHI) of 7, 14 and 21 days.     

MSPD–GC–MS–MS Determination of Residues of 15 Organic Nitrogen-Containing Pesticides in Vegetables

A novel and simple method for determination of 15 organic nitrogen-containing pesticides in vegetables using matrix solid-phase dispersion (MSPD) coupled with gas chromatography tandem mass spectrometry (GC–MS–MS) has been developed. The efficiencies of different sorbents (florisil, silicone, neutral alumina) for the MSPD were compared. Mean recoveries of the method using neutral alumina varied from 73.26 to 111.83% with relative standard deviations of 0.79–15.33% in the concentration range of 0.01, 0.02 and 0.05 mg kg^?1. The limits of detection were typically in the 0.0007–0.0320 mg kg^?1 range, which were 10–100 times lower than the maximum residue levels established by the European Union. This method was applied to residue detection in vegetables, in which organic nitrogen-containing compounds were detected at low concentrations.     

A multi-residue method for pesticide residue analysis in rice grains using matrix solid-phase dispersion extraction and high-performance liquid chromatography–diode array detection

Pesticides are widely used in rice cultivation, often resulting in detection of their residues in rice grains. So far, no analytical method has been available for the simultaneous determination of most rice pesticides in rice grains. This paper reports the development and validation of such a method for the determination of eight rice pesticides (penoxsulam tricyclazole, propanil, azoxystrobin, molinate, profoxydim, cyhalofop-butyl, deltamethrin) and 3,4-dichloroaniline, the main metabolite of propanil. Pesticide extraction and clean-up was performed by an optimized matrix solid-phase dispersion (MSPD) protocol on neutral alumina (5 g) using acetonitrile as the elution solvent. Samples were analyzed in a high-performance liquid chromatography–diode array detection (HPLC-DAD) system. Pesticide separation was achieved with a mobile phase of acetonitrile/water in a linear elution gradient from 30:70% (v/v) to 100:0% (v/v) in 14 min at a flow rate of 0.8 mL min^?1. Method validation was performed by means of linearity, intra-day accuracy, inter-day precision and sensitivity. Linear regression coefficients (R ²) were always above 0.9948. Limits of detection (LOD) and quantification (LOQ) varied from 0.002 to 0.200 mg kg^?1 and 0.006 to 0.600 mg kg^?1, respectively. Recoveries were investigated at three fortification levels and were found to be acceptable (74–127%) with relative standard deviations (RSD) below 12%. Application of the method for the analysis of five commercial rice grain samples showed that the pesticide levels were below the LOD. Overall, the method developed is suitable for the determination of residues of most rice pesticides in rice grains at levels below the established MRLs.     

Analysis of 28 insecticides in curry leaves (Murraya koenigii L.) by gas chromatography and gas chromatography–mass spectrometry

A simple and efficient method was developed for analysis of 28 insecticides (organochlorines, organophosphates and synthetic pyrethroids) in curry leaves (Murraya koenigii L.). The extraction of the analytes was carried out with acidified acetonitrile and purification with magnesium sulphate, primary secondary amine along with graphitised carbon black to remove excess chlorophyll content in curry leaves. Acetonitrile extracts were changed into hexane + acetone (9 + 1) and hexane + toluene (9 + 1) in the final step. In another method ethyl acetate was used for extraction and purification was carried out as above. The analytes in the samples were determined by gas chromatography (GC) and confirmed by gas chromatography–mass spectrometry (GC–MS). Use of ethyl acetate increased the recovery of the analytes, but co-extractive interference led to higher GC maintenance. Acidified acetonitrile was found to be a better extraction solvent compared with ethyl acetate. The use of hexane:toluene (9:1) as exchange solvent increased the recovery of organochlorine insecticides compared with hexane:acetone (9:1). The limit of quantification (LOQ) of the method was 0.01 mg kg^?1 for organochlorine insecticides and 0.05 mg kg^?1 for organophosphates and synthetic pyrethroids. The recoveries of organochlorines were within 70.36–82.45%; organophosphates, 82.54–90.93% and synthetic pyrethroids, 88.45–90.71% at the LOQ level. The method developed was found suitable for analysis of real samples of curry leaves. The pesticides detected in curry leaves collected from the retail market were mainly organophosphates and synthetic pyrethroids.     

Comparison of an HPTLC method with the Reflectoquant assay for rapid determination of 5-hydroxymethylfurfural in honey

5-Hydroxymethylfurfural (HMF) was analyzed in 17 botanical varieties of honey from 12 countries. A recently developed high-performance thin-layer chromatographic (HPTLC) method was limited because of increased matrix effects at higher honey sample loading. Therefore, the method was modified to achieve higher sensitivity and eliminate matrix interference by use of rectangular application combined with a focusing step. The HPTLC results were compared with results from the new spectrophotometric Reflectoquant hydroxymethylfurfural assay. Both methods had quantification limits of 4 mg kg^?1 and were suitable for rapid quantification of HMF in honey at the strictest regulated level of 15 mg kg^?1. Comparable results were obtained for the 17 honey samples, with a mean deviation of 2.9 mg kg^?1 (15 %). The optimized HPTLC method was proved to be highly matrix-robust and was validated for the 17 different honey matrices (correlation coefficients ≥0.9994 (n?=?6), mean intra-day precision 3.2 % (n?=?3 within a plate; n?=?2 repeated within a day), mean inter-day precision 3.7 % (n?=?3), mean reproducibility over the whole procedure including sample preparation 4.1 % (n?=?2), and mean recovery 106.9 % (n?=?5 different concentrations; n?=?4 different honey matrices). Recovery for a range of different application volumes, and thus for different honey matrix loading, differed by only ≤4.2 %. HMF results when calculated by use of external calibration and by use of the standard addition method varied by 8.8 %. Both revealed that any matrix effect was minor and that the original matrix interference problem was successfully solved.

MSPD Procedure for Determination of Carbofuran, Pyrimethanil and Tetraconazole Residues in Banana by GC–MS

An extraction method based on matrix solid-phase dispersion was developed to determine carbofuran, pyrimethanil and tetraconazole in banana using gas chromatography–mass spectrometry. The best results were obtained using 2.0 g of banana, 1.0 g of silica as dispersant sorbent and n-hexane:ethyl acetate (1:4, v/v) as eluting solvent. The method was validated using banana samples fortified with pesticides at different concentration levels (0.05–2.0 mg kg^?1). Average recoveries (four replicates) ranged from 68 to 111%, with relative standard deviations between 6.6 and 20.5%. Detection and quantification limits for banana ranged from 0.02 to 0.05 and 0.05 to 0.10 mg kg^?1, respectively.     

Use of a Headspace Solid-Phase Microextraction-Based Methodology Followed by Gas Chromatography–Tandem Mass Spectrometry for Pesticide Multiresidue Determination in Teas

This study reports on the development of a fast and efficient method based on headspace solid-phase microextraction (HS-SPME) coupled to gas chromatography–tandem mass spectrometry (GC–MS/MS) for simultaneous analysis of 128 volatile or semi-volatile pesticide residues belonging to nine classes of pesticides. The important factors related to HS-SPME performance were optimized; these factors include fiber types, water volume, ion strength, extraction temperature, and extraction time. The best extraction conditions include a PDMS/DVB fiber, and analytes were extracted at 90 °C for 60 min from 1 g of tea added to 5 mL of 0.2 g mL^?1 NaCl solution. The methodology was validated using tea samples spiked with pesticides at three concentration levels (10, 50, and 100 μg kg^?1). In green tea, oolong tea, black tea, and puer tea, 82.8, 88.3, 79.7, and 84.3% of the targeted pesticides meet recoveries ranging from 70 to 120% with a relative standard deviation of?≤?20%, respectively, when spiked at a level of 10 μg kg^?1. Limits of quantification in this method for most of the pesticides were 1 or 5 μg kg^?1, which are far below their maximum residue limits prescribed by EU. The optimized method was employed to analyze 30 commercial samples obtained from local markets; 17 pesticide residues were detected at concentrations of 2–452 μg kg^?1. Chlorpyrifos was the most detected pesticide in 80% of the samples, and the highest concentration of dicofol (452 μg kg^?1) was found in a puer tea. This is the first time to find that the optimized extraction temperature for pesticide residues is 90 °C, which is much higher than other reported HS-SPME extraction conditions in tea samples. This developed method could be used to screen over one hundred volatile or semi-volatile pesticide residues which belong to multiple classes in tea samples, and it is an accurate and reliable technique.     

Erratum to: Evaluation of Three Multiresidue Methods for the Determination of Pesticides in Marijuana (Cannabis sativa L.) with Liquid Chromatography-Tandem Mass Spectrometry

Marijuana (non-medical cannabis) is a well-recognized psychoactive herbal drug used for recreational purposes. The aim of this work is to describe and compare the performance and suitability of selected methods to analyze pesticide residues in marijuana. The fitness of three typical pesticide multiresidue methods [acetate buffered QuEChERS (method A), a modified citrate buffered QuEChERS (method B) and citrate buffered QuEChERS (method C)] were tested in marijuana through the LC–MS/MS determination of 61 LC amenable pesticides. Considering recoveries at the highest level for the selected pesticides in marijuana, from the 61 target analytes, 37 (method A), 40 (method B) and 46 (method C) compounds gave accurate results (70–120 % range). Method C showed the best performance for the target analytes in terms of recoveries, precision, limits of quantitation and matrix effect. Marijuana showed to be a highly complex matrix. Most analytes suffered high signal suppression (ME <−50 %) for method B while medium (−50 to 20 %) to low (−20 to 0 %) signal suppression was found for methods A and C. Moreover, high coelution of coextractives with the target analytes was observed. A pilot survey with real samples revealed that seized and legally produced marijuana samples contained pesticides. Residues of diazinon (0.03 mg kg⁻¹), tebuconazole (0.19 mg kg⁻¹) and teflubenzuron (0.11 mg kg⁻¹) were simultaneously detected in one marijuana sample. The establishment of MRLs in a legal consumption scenario such as in Uruguay seems to be necessary in the near future.

     

Residue dynamics of chlorpyrifos and cypermethrin in/on pomegranate (Punica granatum L.) fruits and soil

Study on the residue dynamics of chlorpyrifos and cypermethrin in/on pomegranate (Punica granatum L.) and soil was carried out by conducting supervised field trials as per good agricultural practices. A modified QuEChERS was used to extract the insecticides in pomegranate peel and aril and soil. The limit of quantification (LOQ) of chlorpyrifos and cypermethrin were 0.01 and 0.05 mg kg^?1, respectively. Residues of the insecticides remained on the fruit surface and movement to the edible part (aril) was not observed. The residues after treatment on fruit peel were 2.46 and 3.51 mg kg^?1 and 2.84 and 4.54 mg kg^?1 for chlorpyrifos and cypermethrin, respectively, from recommended and double dose treatments. Chlorpyrifos residues degraded faster compared to cypermethrin. The pre-harvest intervals (PHIs) of chlorpyrifos were 22 and 35 days and those of cypermethrin 50 and 73 days, respectively, at recommended and double dose treatments. In the experimental field soil after the second application chlorpyrifos residues were 0.21 and 0.46 mg kg^?1 and cypermethrin residues 0.15 and 0.36 mg kg^?1. At harvest, both pesticides showed residues below the LOQ. Based on this study, application of cypermethrin towards harvest may be avoided whereas chlorpyrifos can be applied with 22 days PHI.     

Biodegradation of imidacloprid in sandy loam soil by Bacillus aerophilus

A study of the biodegradation of imidacloprid in soil was carried out under laboratory conditions. Sandy soil samples were fortified with imidacloprid at 50, 100 and 150 mg kg^?1 along with 45 x 10⁷ colony forming units (cfus) of Bacillus aerophilus and the samples were compared with unamended soil. The samples were extracted with acetonitrile, cleaned up by treatment with primary secondary amine sorbent and graphitised carbon black. The residues of imidacloprid and its metabolites were analysed by high performance liquid chromatography. The parent compound, imidacloprid, was found to be more persistent in both the treatments. Among metabolites, the highest values were obtained for urea and olefin while 5-hydroxy, 6-chloronicotinic acid (6-CNA), nitrosimine and nitroguanidine (NTG) were also observed in all the treatments in amended soil. In case of unamended (control) soil, 6-CNA was found to be the most persistent metabolite followed by olefin, urea, 5-hydroxy, nitrosimine and NTG metabolites. Total imidacloprid residues for control soil samples followed first-order kinetics at 50 and 150 mg kg^?1 but in case of control imidacloprid fortified at 100 mg kg^?1, the total residues of imidacloprid and its metabolites followed pseudo-first-order kinetics. The respective half-life value for 50 mg kg^?1 was 25.08 days and 30.10 days for both 100 and 150 mg kg^?1. However, total imidacloprid residues followed pseudo-first-order kinetics for its applications at 50, 100 and 150 mg kg^?1 in sandy loam soil amended with B. aerophilus. The half-life values for 50, 100 and 150 mg kg^?1 were worked out to be 14.33, 15.05 and 18.81 days, respectively. With the use of B. aerophilus, the reduction percentage of initial applied dose imidacloprid in sandy loam soil was found to be higher in all the three doses as compared to that of the control samples.     

Analysis of bioaccessible concentration of trace elements in plant based edible materials by INAA and ICPMS methods

The total metal concentration and bioaccessible concentration of Cr, Mn, Fe, Cu, Zn, Se in Momordica charantia, Asparagus racemosus, Terminalia arjuna and Syzyzium cumini were measured by instrumental neutron activation analysis and by inductively coupled plasma mass spectrometry analysis (ICP-MS). The bioaccessible concentrations were determined in the gastrointestinal digest obtained after treating dried powdered samples sequentially in gastric and intestinal fluid of porcine origin at physiological conditions. The bioaccessible concentration of Fe was in the range of 58–67 mg kg^?1, Mn was 10.2–14.6 mg kg^?1, Cu was 3.7–4.8 mg kg^?1 and Zn was 10.6–18.4 mg kg^?1, were within the safety limits set for vegetable food stuff set by Joint FAO/WHO. The bioaccessibility of Zn, an essential element, was high (40–50 %) in M. charantia and in S. cumini. In addition, the total metal contents and bioaccessible concentration of Ni, Se, Cd and Pb in these samples were measured by ICP-MS. The total Cd content in S. cumini (2.6 ± 0.2 mg kg^?1) and its bioaccessible concentration (0.6 mg kg^?1) were strikingly high as compared to the other samples. Though total Hg contents were determined by ICP-MS, but their bioaccessible concentrations were below the detection limit (0.036 mg kg^?1).     

Uncertainty Analysis of Chlormequat Residue in Fruits by LC�CMS�CMS

A method for determination of chlormequat (CCC) residue in fruits by liquid chromatography?Ctandem mass spectrometry (LC?CMS?CMS) was developed. Residue of CCC was extracted from samples with methanol?Cwater (v/v, 1:1) containing 1.0% acetic acid, cleaned up by strong cationic exchange (SCX) cartridge, and then determined by LC?CMS?CMS. The method showed good linearity over the concentration range 0.002?C5.0 mg kg^?1 with correlation coefficient above 0.997. The limit of detection (LOD) and limit of quantitation (LOQ) for CCC were 5 × 10^?4 mg kg^?1 (S/N = 3) and 0.002 mg kg^?1 (S/N = 10), respectively. Recoveries for CCC at three spiked levels (0.025, 0.050, and 0.20 mg kg^?1) were in the range 80?C102%. Estimation of measurement uncertainty was calculated for CCC at the level of 0.025 mg kg^?1 in fruits. The results demonstrated that the uncertainty of recovery was the main contribution to the combined standard uncertainty. The relative combined standard uncertainties associated with the method ranged from 11 to 13%, depending on the sample matrices.     

Screening Method for the Determination at Parts Per Trillion Levels of Pesticide Residues in Vegetables Combining Solid‐Phase Microextraction and Gas Chromatography‐Tandem Mass Spectrometry

Abstract

A new analytical method is proposed for determining residues of 70 pesticides of different chemical families at parts per trillion levels in fresh vegetables. For that, only 4 g of the vegetable samples were quickly extracted with 10 ml of ethyl acetate. The method is based on a vanguard/rearguard strategy that reduces the average time required per sample when the method is applied to a high number of vegetable samples in a quality control laboratory. At the beginning, an aliquot of the extract is evaporated and re‐dissolved in a mixture water:acetone (9∶1 v/v). For screening purposes, the pesticides were extracted for only 10 min by direct immersion of a solid‐phase microextraction (SPME) fiber (65 µm polydimethylsiloxane‐divinylbenzene, PDMS‐DVB). The SPME device was automated and on‐line coupled to a gas chromatograph with an ion trap mass spectrometer (GC‐MS) operated in full scan mode for screening in less than 18 min those samples that potentially contain pesticides above 0.01 mg kg^?1 (cut off value). After that, only those potentially non‐negative samples were reanalyzed by a sensitive quantifying/confirming method that re‐extract by SPME the pesticides in 55 min of absorption and determine them by GC with tandem MS (MS/MS). The method has been validated following EU guidelines and compared with a conventional extraction method based on the use of higher amounts of organic solvents. The limits of detection (LOD), confirmation (LOC) and quantitation (LOQ) as well as the calibration curves obtained allowed the determination of the target pesticides at concentrations clearly below the maximum residue levels (MRL) stated by EU being possible the determination of parts per trillion of the pesticides in ecological (green) vegetables. The method has been applied to the analysis of real samples and the results compared with those obtained by a conventional extraction method accredited by ENAC (Spanish Accreditation Body). The proposed method was also evaluated participating in a proficiency test with adequate results (z‐score among±2).     

Determination of Urea in Milk by Liquid Chromatography-Isotope Dilution Mass Spectrometry

A definitive method based on liquid chromatography isotope dilution mass spectrometry (LC-IDMS) has been developed for the determination of milk urea, an indicator of nutrition status for the lactating animals. The milk samples were treated twice by sequentially adding acetonitrile and chloroform to precipitate proteins and then were directly separated using normal phase liquid chromatography without chemical derivatization. After the matrix separation, exact matching IDMS was used for the determination of milk urea, with high accuracy, high precision, good linearity and low uncertainty. The recoveries obtained for the four spiked milk samples were 100.6–102.2%. The linear range of signal responses was 10–2000 mg · kg^?1 with a linearity coefficient of 0.9995. The intraday and interday precisions in terms with relative standard deviations (RSDs) were 0.17–0.38% and 0.28–0.40%, respectively. The uncertainties of the whole sample analysis process were estimated to be 0.83%, 0.60%, and 0.64% for three samples with concentrations of 151.28, 184.36, and 266.66 mg · kg^?1.