FeVO4催化剂的原位电导研究

采用盐类固体研磨法制备了FeVO4催化剂,用原位电导方法测定了FeVO4催化剂在氧气 丙烷→氧气→丙烷连续变化气氛下的电导变化,确定其导电类型.以BET、XRD、H2-TPR等技术对催化剂进行表征,研究了其对丙烷氧化脱氢制丙烯反应的催化性能.     

Ni-V-O催化剂上丙烷氧化脱氢制丙烯的反应

考察了Ｎｉ－Ｖ－Ｏ系列催化剂对丙烷氧化脱氢反应的催化性能,结合ＸＲＤ和电导法等表征结果研究了催化剂的物相结构与仙化活性之间的关系。结果表明：同ｎ型半导体氧化物相比,ｐ型半导体具有优良的催化性能,并且丙烯的选择性与催化剂中ＮｉＯ及Ｎｉ３Ｖ２Ｏ８相的共存有关。适当控制反应条件,４５２℃时该系列催化剂可达到１８．６％的丙烷转化率和４９．９％的丙烯选择性。     

丙烷氧化脱氢氧化物催化剂的活性氧物种

研究了半导体金属氧化物催化剂丙烷氧化脱氧制丙烯的性能，发现p-型半导体金属氧化物有低温催化性能，n-型半导体金属氧化物有高温催化性能，H2－TPR，O2－TPD－MS和原位电导研究结果表明，p-型半导体金属氧化物的活性氧物种为非化学计量氧物种，n-型半导体的活性氧物种为表面晶格氧。     

钼掺杂LaVO4上丙烷氧化脱氢

研究了钼掺杂LaVO4催化剂的丙烷氧化脱氢催化性能.加入钼对丙烷氧化脱氢反应有很好的助催化作用.当丙烷转化率恒定在10％和20％时，丙烯选择性在LaMo0.1V0.9O4.05上分别达到了56％和43％，而在LaVO4上仅为36％和22％，这归结为钼掺杂催化剂上有利于丙烯生成的可活动氧物种的增加和催化剂氧化还原性的改变.     

不同孔道结构的氧化硅负载钒氧化物催化丙烷氧化脱氢

采用固定床微型反应装置,结合催化剂的原位电子自旋共振光谱、程序升温表面反应和紫外漫反射光谱等技术,研究了丙烷氧化脱氢的介孔氧化硅负载钒氧化物催化剂的性能和表面氧物种的状态及其反应性.结果表明,催化剂载体孔结构是影响钒氧物种分散状态乃至催化性能的一个重要因素.SBA-15负载钒氧化物催化剂因具有较大的比表面积和较大的孔径,不仅具有较高的丙烷氧化脱氢催化活性,而且具有较高的丙烯选择性.复合型钒氧化物催化剂表面与V离子相连的晶格氧物种是丙烷氧化脱氢牛成内烯的主要活性物种,载体表面高度分散的钒氧物种具有较高的丙烷氧化脱氢催化活性.负载型钒氧化物催化剂晶格氧物种是丙烷氧化脱氢转化为丙稀的主要活性物种,CO_2分子可以再生钒氧化物催化剂的晶格氧物种,同时它对丙烯的深度氧化作用较弱,因此在负载型钒氧化物催化剂上CO_2氧化丙烷可高选择性地生成丙烯.     

Ni-V-O催化剂的合成、表征及其催化性能

制备了Ni3V2O8, Ni2V2O7, NiV2O6催化剂, 进行了XRD, BET, H2-TPR, XPS和电导等表征, 并测试了这三种结构催化剂对丙烷氧化脱氢制丙烯反应的催化性能, 分析了影响催化性能的因素. 实验结果表明, 当丙烷的转化率为10%时, 在p-型半导体Ni3V2O8和Ni2V2O7催化剂上丙烯的选择性为69.13%和70.21%, 而在n-型半导体NiV2O6上, 丙烯的选择性为64.41%, 表明p-型半导体Ni3V2O8和Ni2V2O7的催化性能优于n-型半导体NiV2O6的催化性能. XPS实验结果表明, 这可能与p-型半导体正钒酸镍(Ni3V2O8)和焦钒酸镍(Ni2V2O7)催化剂表面含较多O-氧物种和V4+有关.     

水蒸汽对负载型催化剂丙烷脱氢性能的影响：Ⅰ.反应性能的研究

研究了ＭｇＡｌ２Ｏ４，ＺｎＡｌ２Ｏ４负载的Ｐｔ－Ｓｎ催化剂在氮气及水蒸汽中的丙烷脱氢性能。考察了还原温度，反应温度，催化剂载量对Ｐｔ－ＳＳｎ／ＭｇＡｌ２Ｏ４催化剂丙烷脱氢性能的影响。     

负载型钒基催化剂上丙烷的临氧活化转化

用ＴＰＳＲ（程序升湿表面反应）－ＴＲ（ＦＴ）ＩＲ技术,研究临氧条件下丙烷负载型钒基催化剂上的活化和转化,并与催化剂的可不原性和表面酸性相关联,丙烷氧化脱氢生成丙烯与深度氧化生成ＣＯｘ的起始反应温度相同;而裂解产物Ｃ２Ｈ４和ＣＨ４的生成温度比丙烷氧化脱氢生成丙烯的高得多,可能主要源于丙烷的高温气相裂解,催化剂的表面酸性位和强的可还原性,有利于丙烷中Ｃ－Ｈ键的活化和临氧转化,降低起以攻提高丙烷转化率,     

丙烷氧化脱氢不同硅基载体负载钒氧化物催化剂的TPSR表征

研究了钒负载不同氧化硅载体(Silica-gel,SBA-15,MCM-41,fumed-SiO2,Nano-SiO2)的丙烷氧化脱氢(ODH)催化剂的结构特征和催化性能,结合催化剂的程序升温表面反应(TPSR)的差热热重质谱(TG-DSC-MS)和原位紫外漫反射光谱(UV-vis DRS)等技术,研究钒在载体上的分散度和晶格氧的反应性。结果表明:负载型钒氧化物催化剂的活性取决于钒在不同硅基载体上的分散度,高度分散的隔离的四配位V5+是丙烷氧化脱氢的活性位。C3H6选择性主要与催化剂的平均孔径相关联,平均孔径越小,产物C3H6越易发生深度氧化。另外,不同氧化硅载体晶格氧与钒的结合强度对C3H6的选择性也产生影响,结合力较弱的V-O-Si中的晶格氧是丙烷氧化脱氢的燃烧位,且燃烧温度随晶格氧与钒、硅结合强度的减小而降低。而与钒结合力较强的V=O和V-O-V中的晶格氧是丙烷氧化脱氢的选择氧化位。硅基载体形貌和结构的不同导致负载型钒氧化物催化剂丙烷氧化脱氢活性和选择性发生差异。     

钴钼氧化物催化剂对丙烷催化氧化脱氢反应的研究

考察了Ｃｏ－ＭＯ原子比不同的氧化物对丙烷催化脱氢制丙烯的催化活性和选择性，并利用ＸＲＤ、ＴＰＲ、ＩＲ和ＸＰＳ等技术，表片了催化剂的体相及表面结构，研究表明，催化剂的Ｃｏ－Ｍｏ比对催化性能的影响随反应温度而改变，当Ｃｏ－Ｍｏ比低于１时，在４００－４４０℃温度范围内，丙烯的选择性可达４０－６５％，显示了此系列催化剂对丙烷氧化脱氢丙烯的低温催化性能，ＭｏＯ３单相的存在有利于丙烯的生成。     

稀土铈掺杂对甲烷高温燃烧催化剂LaFeAl11O19结构和性能的影响

六铝酸盐甲烷高温燃烧催化剂研究目前主要集中在BaMnA l11O19基和LaMnA l11O19基的催化剂上[1-4],关于LaFeA l11O19催化剂研究相对较少,而据文献报道[5]在沉淀法制备取代型的六铝酸钡催化剂中铁和锰活性相近,但铁比锰具有更高的耐高温和抗水热冲击的能力,因此本工作选择LaFeA l     

Conductivity properties of Na2SO4/CaCO3 catalysts and their effect on catalytic activities for oxidative coupling of methane

A series of Na₂SO₄ doped CaCO₃ catalysts were prepared. It was observed that the C₂ yields and selectivities of Na₂SO₄/CaCO₃ catalysts for OCM are intimately related to their conductivities. The effect of conductivity on the catalytic activity is discussed together with the conductivities and catalytic activities of the catalysts. The higher the conductivities, the higher the C₂ yields and selectivities are.     

制备方法对Cr/Si-2催化剂在CO2氧化乙烷脱氢制乙烯反应中的催化性能的影响

采用直接水热合成法和浸渍法制备了相同Cr含量的Cr/Si-2催化剂,并在常压固定床微反应器上,考察了它们在CO2或者N2气氛下的乙烷脱氢制乙烯反应中的催化性能及稳定性.由于存在逆水煤气反应和Boudouard反应,CO2能显著促进乙烷的脱氢反应.不论是在CO2还是在N2气氛下,直接水热法制备的催化剂均比浸渍法制备的催化剂显示出更好的催化性能.高价态的Cr物种被认为是催化剂具有高活性的关键.在CO2气氛下的乙烷脱氢制乙烯反应中,浸渍法制备的催化剂比水热法制备的催化剂失活更快,催化剂失活速率的差异可能与它们的氧化还原性质有关.然而在N2气氛下的乙烷脱氢制乙烯反应中,这两种方法制备的催化剂失活速率差异不大.     

Liquid-phase catalytic degradation of polyethylene wax over MFI zeolites with different particle sizes

The liquid-phase catalytic degradation of polyethylene wax into fuel oil was studied over MFI catalysts with different particle sizes (0.2 to 4.0 μm). Although structures and acidities of these catalysts were almost the same, the degradation activity varied greatly according to their particle size. The small particle catalyst showed higher activity due to its larger external surface, due to the low restriction on the mass transfer of large polymer molecules. Product distribution was also dependent on the particle size, producing higher hydrocarbons in the liquid product on the catalyst of small particles. The particle size effect of MFI zeolite on its activity and product composition in the liquid-phase degradation was discussed.     

SOOT combustion. co and k catalysts supported on different supports

The catalytic combustion of particulate material was studied on cobalt catalysts promoted with potassium using different supports for its preparation. Silica, aluminium oxides and hydroxides, zirconium oxide and hydroxide were used as supports. The catalytic activity for combustion depends on the type of support used, the higher activity corresponding to the supported catalyst on zirconium oxide. TPR studies indicate that the interaction metal/support allows to explain the higher activity of the CoK/SiO₂ catalyst with respect to the CoK/Al₂O₃ but the high activity found in CoK/ZrO₂is not explained by this interaction. In all cases the Co and K improved the performance of the catalysts.     

Synthesis of zinc glutarates with various morphologies using an amphiphilic template and their catalytic activities in the copolymerization of carbon dioxide and propylene oxide

Various heterogeneous zinc glutarate (ZnGA) catalysts were synthesized in solvent systems of various polarities from zinc acetate dihydrate and glutaric acid with and without the aid of an amphiphilic block copolymer, poly(ethylene glycol‐b‐propylene glycol‐b‐ethylene glycol) (PE6400), as a template. The presence of the PE6400 template and the polarity of the solvent significantly affected the morphology, particle size, surface area, and crystallinity of the resulting catalyst. However, all the catalysts had the same crystal lattice unit cell structure and similar surface compositions. The surface compositions of the catalysts were quite different from those of conventionally prepared ZnGA catalysts, that is, those prepared from zinc oxide and glutaric acid in toluene. All these characteristics of the catalysts influenced the ZnGA‐catalyzed copolymerization of carbon dioxide and propylene oxide. The catalytic activities of the catalysts in this copolymerization depended primarily on their surface area and secondarily on their crystallinity; a larger surface area and a higher crystallinity resulted in higher catalytic activity. Of the catalysts that we prepared, the ZnGA catalyst that was prepared in ethanol containing 5.5 wt % water with the PE6400 template, ZnGA‐PE3, exhibited the highest catalytic activity in the copolymerization. The catalytic activity of ZnGA‐PE3 was attributed to its wrinkled petal bundle morphology, which provided a large surface area and high crystallinity. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 4079–4088, 2005     

不同Ce/Mn摩尔比对CeO_2-MnO_x催化剂低温NH_3选择性催化还原NO的影响

以高锰酸钾和硝酸锰为锰源,采用改进的共沉淀法制备了不同Ce/Mn摩尔比的Ce O2-Mn Ox催化剂.以NH3为还原剂,考察了催化剂低温(小于150℃)NH3选择性催化还原NO的性能.并采用XRD,BET,H2-TPR,NH3-TPD和XPS等手段对催化剂的物理化学性质进行表征.结果表明,Ce O2-Mn Ox催化剂在50~150℃温度区间内表现出了良好的催化活性.引入适量的Ce可以有效地改变催化剂的晶粒大小,增强其氧化还原能力;而Mn的加入,促进了其低温SCR活性.当Ce/Mn摩尔比为1∶3时(C1M3),低温活性最佳,在82~150℃温度区间内NO去除率达到90%以上,这主要是由于C1M3催化剂有较高含量的表面吸附氧、大量的弱酸性位点、良好的氧化还原性能以及表面较高含量的Mn4+物种.