两亲性PS-b-PEG嵌段共聚物刷的合成及响应行为

利用原子转移自由基聚合(ATRP)和点击化学(Click)反应, 在硅基底上制备了聚苯乙烯-b-聚乙二醇(PS-b-PEG)两亲性嵌段共聚物刷. 首先, 利用ATRP方法在表面改性的硅片引发苯乙烯单体(St)的聚合, 得到PS-Br均聚刷, 然后通过叠氮化钠(NaN3)将均聚刷末端功能化为PS-N3, 再与炔基聚乙二醇甲醚(Alkynyl-PEG)发生Click反应, 得到PS-b-PEG嵌段共聚物刷. 通过X射线光电子能谱(XPS)和接触角测量仪表征了聚合物刷的表面化学组成和表面亲疏水性质, 证明在硅基底上接枝了嵌段共聚物刷. 用原子力显微镜(AFM)观察了PS-b-PEG嵌段共聚物刷在不同溶剂处理后的形态结构变化, 研究了其响应行为.     

用原子转移自由基聚合方法制备新型含有高分子金属配合物的无机-有机杂化材料

近年来,表面引发聚合制备聚合物刷,由于其能控制无机物表面性能,在材料科学方面有广泛的应用前景．在制备聚合物刷的一系列聚合方法中,“活性”／可控自由基聚合,尤其是原子转移自由基聚合(Atom Transfer Radical Polymerization,ATRP)得到广泛使用．它可获得分子量分布较窄的结构规整的聚合物,可将一些功能性的单体引入聚合物体系获得功能聚合物,     

由平面合成聚合物刷--表面引发原子转移自由基聚合研究进展

原子转移自由基聚合反应(ATRP)是实现活性聚合,获得可控聚合物的一种有效途径。通过表面引发原子转移自由基聚合,在材料表面合成聚合物刷,是改变材料表面特征的有效方法。本文综述了表面引发原子转移自由基聚合合成聚合物刷及其最新进展。     

激光调控自缩合表面引发原子转移自由基聚合制备超支化聚乙二醇刷

采用二溴异丁基酯化低聚乙二醇甲基丙烯酸酯(OEGMA-Br)为自引发性单体,以三(2-苯基吡啶)合铱为光氧化还原催化剂,通过激光调控自缩合表面引发原子转移自由基聚合(SI-ATRP),在硅片表面制备超支化聚乙二醇(PEG)聚合物刷.在对硅片-溶液界面与硅片表面溶液中自引发性单体OEGMA-Br自缩合ATRP反应机理推导的基础上,硅片表面反应溶液的核磁共振(1H-NMR)表征及聚合物刷表面活性末端官能团的光电子能谱(XPS)表征证实了所得表面PEG聚合物刷的超支化结构;椭圆偏光仪对不同反应条件下聚合物刷厚度的表征表明过高或过低的自引发性单体浓度均不利于超支化PEG聚合物刷的生长,同时其生长过程受到聚合时间和光辐照强度的影响;采用异硫氰酸荧光素(FITC)标记牛血清蛋白表面吸附实验证明PEG聚合物刷微图案的非特异性抗蛋白吸附性能.     

基于聚合物刷微图案的生物素化梯度表面制备研究

提出了基于叠氮功能化聚合物刷微图案制备生物素化梯度表面的方法 .通过数字微镜器件(DMD)调控光辐照引发表面原子转移自由基聚合(ATRP)反应,制备叠氮功能化的聚(2-(2-叠氮-2-甲基丙氧基)甲基丙烯酸乙酯)(PAMEMA)聚合物刷微图案,采用X射线光电子能谱仪(XPS)和飞行时间二次离子质谱仪(TOF-SIMS)对PAMEMA聚合物刷微图案的化学组成及分布进行表征,表明叠氮基团在聚合物刷图案化表面的区域选择性分布;以叠氮基团为反应位点,通过点击化学反应实现PAMEMA聚合物刷微图案表面的生物素化,借助荧光标记的链霉亲和素染色实验表征生物素在微图案表面的分布情况;以具有厚度变化的PAMEMA聚合物刷微图案为模板制备生物素表面,结果表明通过控制聚合物刷的厚度可以对微图案表面固定生物素分子的空间密度进行调控以实现具有复杂结构的生物素化梯度表面的成功制备.     

亚表面引发原子转移自由基聚合制备牢固的嵌入式聚合物刷

本文展示了一种新的材料表面改性方法:原子转移自由基聚合(sSI-ATRP)的亚表面修饰,即通过ATRP反应在聚合物材料界面嵌入聚合物刷,构筑稳定的、厚的聚合物亚表面层.首先,将ATRP引发剂分子通过共价键引入到丙烯酸树脂、聚氨酯、聚酯、环氧树脂等聚合物材料中,然后该基底材料在含有催化剂的单体溶液中引发表面原子转移自由基聚合.表面接枝的亲水聚合物刷使材料的表面变得亲水并发生溶胀,使得单体溶液可以进一步接触到材料内部的引发剂而引发新的ATRP反应,该过程不断重复,最后在基材表面上形成几十微米厚的聚合物刷改性的亚表面层.与传统的表面接枝的聚合物刷相比,这种嵌入式的聚合物刷赋予材料表面改性层更好的机械性能,可承受高载摩擦和更好的抗海生物附着特性,且在改性亚表面层破坏后,不需要引发剂修饰组装而再次重复引发聚合改性.     

Au/聚4-乙烯基吡啶-b-聚乙二醇嵌段聚合物刷的合成及其pH响应行为

作为受限高分子体系的一个经典模型,高分子刷在胶体稳定、聚合物链的自组装以及摩擦学等方面具有潜在的应用价值。 本文通过原子转移自由基聚合(ATRP)和点击化学(Click Chemistry)方法在金(Au)基底表面制备了pH响应性聚4-乙烯基吡啶-b-聚乙二醇(P4VP-b-PEG)嵌段聚合物刷。 通过频率-耗散型石英微天平(QCM-D)、X射线光电子能谱(XPS)和原子力显微镜(AFM)等技术手段分别对Au/P4VP-b-PEG聚合物刷经不同pH值溶液处理后的形态变化、表面组成和表面形貌进行了进一步深入研究。 结果表明,用不同pH值溶液处理P4VP-b-PEG嵌段聚合物刷后,该聚合物刷呈现刺激响应规律。 当pH=1.5时,P4VP链段质子化,由于静电排斥作用使P4VP-b-PEG链段呈伸展构象;当pH=11.5时,P4VP链段去质子化,并且由于失去部分结合水,P4VP-b-PEG链段呈塌缩构象。     

表面引发聚合新进展及应用

综述了近年来聚合物刷合成与应用方面的新进展.简要介绍了利用表面引发原子转移自由基聚合(SI-ATRP)制备聚合物刷的历程和重要进展.重点论述了通过电化学、光诱导以及牺牲阳极技术、仿生合成等发展了多种表面引发ATRP新方法,基于如何将聚合物从分子尺度过渡到微米尺度的思考,实现了多尺度聚合物刷结构的制备.简要综述了聚合物刷在以下3个方面的应用研究:(1)智能驱动,利用聚合物刷构象变化,实现微悬臂驱动、辅助放大的电驱动以及仿毛毛虫运动.(2)生物润滑,利用聚合物的环境响应行为实现了对摩擦系数的调控,并发展了球刷型润滑材料.(3)表面防污,表面接枝含离子液体官能团的聚合物刷,并与仿生技术相结合,利用化学组成和结构化协同效应,得到一系列高性能低毒海洋防污界面材料.     

Preparation of Colloidosome Microcapsules Based on Particle Stabilized Photo-Crosslinkable Pickering Emulsions

研究了光敏性聚合物刷修饰二氧化硅纳米粒子的制备及其乳化行为,提供了一种制备新颖＂胶体体＂微胶囊的方法.首先,在二氧化硅纳米粒子表面引入原子转移自由基聚合（ATRP）引发剂分子,通过表面引发ATRP得到含有香豆素侧基聚合物刷光敏性的纳米二氧化硅粒子（SiO2-PMMA-PCMA）;然后,以该粒子为乳化剂制备油包水型的皮克林乳液;最后,在紫外光的照射下引发香豆素侧基的交联反应从而得到＂胶体体＂微胶囊.结果表明,香豆素单体7-（2-甲基丙烯酰乙氧基）-4-甲基香豆素（CMA）和SiO2-PMMA-PCMA在紫外光作用下都可以发生交联反应,以SiO2-PMMA-PCMA纳米粒子作乳化剂可以制备稳定的皮克林乳液,光交联后得到的＂胶体体＂微胶囊的平均粒径约为170μm.     

机理转移法合成星形梳状聚丁二烯-g-聚甲基丙烯酸甲酯共聚物的研究

结合活性负离子聚合与原子转移自由基聚合(ATRP),采用机理转移法制备了一系列窄分布且分子量可控的星形梳状聚丁二烯-g-聚甲基丙烯酸甲酯接枝共聚物(SC-(PB-g-PMMA)).首先通过阴离子聚合,制备星形聚丁二烯,后经甲酸-过氧化氢原位环氧化对链中部分双键进行环氧化,再与原位生成2-溴异丁酸发生酯化反应,得到具有链中活性溴的星形大分子引发剂(SPB-Brn).然后,利用该大分子引发剂,采用CuCl/CuCl2/PMDETA催化体系,通过ATRP聚合单体MMA,合成出星形梳状SC-(PB-g-PMMA)聚合物.通过GPC,1H-NMR和FTIR等分析手段对合成的星形大分子引发剂及星形梳状聚合物进结构表征,证实得到目标产物,并同时研究了聚合物的热力学性质与溶液性质.     

Preparation of End Grafted Polyacrylonitrile Brushes through Surface Confined Radical Chain Transfer Reaction

End grafted polyacrylonitrile (PAN) brush was prepared through surface initiated polymerization via the chain transfer process.The thiol-terminated monolayer and PAN brushes were characterized by FTIR,X-ray photoelectron spectroscopy(XPS),atomic force microscopy (AFM),ellipsometry and contact angle measurements etc.It is demonstrated that radical chain transfer reaction and surface initiated precipitate polymerization can used to prepare end-grafted polymer brushes.     

Real-time analysis of enzymatic surface-initiated polymerization using surface plasmon resonance (SPR)

The kinetics of enzymatic surface-initiated polymerization of PHB on gold surface has been examined by SPR and the resultant polymer layers characterized by AFM and FT-IR spectrometry. The immobilized enzyme catalyzed surface-initiated polymerization of 3HB-CoA, resulting in the formation of a polymer brush on the surface. The rate of polymer growth from the surface was monitored by SPR in real-time. Polymer growth as measured by the increase in the resonance angle showed no apparent lag phase during the polymerization reaction. SPR analysis also revealed that the thickness of the polymer film could be controlled by varying the initial enzyme density on the surface. The average thicknesses of the PHB film after polymerization reaction were 95, 45 and 15 nm for the surfaces that were treated with 0.5, 0.3 and 0.1*10(-6) M of enzyme, respectively. The binding of PHA synthase at different concentration to the mixed SAMs and subsequent polymerization.     

Poly(lactic acid) brushes grow longer at lower temperatures

Poly(lactic acid) (PLA) brushes prepared by the ring opening of lactide were thicker when polymerized at a lower temperature (25 °C) than was typically used for polymerization in solution. The molecular weight of solution polymerized lactide was also higher when lactide was polymerized at 25 °C compared with polymerization at higher temperatures. However, the yield of PLA was low at this temperature. These results highlight the different requirements for solution polymerization and brush growth. In the former case, both percentage of conversion and molecular weight are important considerations. In the latter case, however, percentage of conversion is unimportant as a brush represents a very small amount of polymer. It was also shown during the course of these studies that the native hydroxy groups on silicon substrates and silanols in solution were equally good initiators when compared with hydroxy terminated self‐assembled monolayers on gold and alcohols, respectively. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3362–3367, 2010     

多次聚合法制备多孔聚吡咯厚膜及其电化学容量性能

为了得到高面积比容量的聚吡咯(PPy)膜超级电容器电极材料, 用多次聚合法合成了PPy厚膜, 聚合电量分别为8、10和12 mAh·cm-2, 掺杂离子分别为氯离子和对甲基苯磺酸根离子(TOS-). PPy膜的电化学性能采用恒电流充放电、循环伏安(CV)和电化学阻抗谱(EIS)等方法测试. 研究表明, 多次聚合法可以制备表面平整且内部均匀多孔的PPy厚膜. 在聚合电量为12 mAh·cm-2时, 用Cl-、TOS-两种离子掺杂的PPy厚膜的面积比容量高达5 F·cm-2, 并表现出理想的电化学容量性能. 同时PPy-Cl厚膜的质量比容量达到330 F·g-1, PPy-TOS厚膜的质量比容量略低(191 F·g-1), 但具有更快的充放电速率. 与一次聚合法合成的PPy 薄膜相比, 多次聚合法合成的PPy厚膜的质量比容量没有降低. 通过场发射扫描电镜(SEM)观察了一次聚合法和多次聚合法制备的PPy厚膜的截面形貌, 并讨论了多次聚合法的合成机理.     

NHS-ester functionalized poly(PEGMA) brushes on silicon surface for covalent protein immobilization

Poly(PEGMA) homopolymer brushes were developed by atom transfer radical polymerization (ATRP) on the initiator-modified silicon surface (Si-initiator). Through covalent binding, protein immobilization on the poly(PEGMA) films was enabled by further NHS-ester functionalization of the poly(PEGMA) chain ends. The formation of polymer brushes was confirmed by assessing the surface composition (XPS) and morphology (atomic force microscopy (AFM), scanning electronic microscopy (SEM)) of the modified silicon wafer. The binding performance of the NHS-ester functionalized surfaces with two proteins horseradish peroxidase (HRP) and chicken immunoglobulin (IgG) was monitored by direct observation. These results suggest that this method which incorporates the properties of polymer brush onto the binding surfaces may be a good strategy suitable for covalent protein immobilization.     

Temperature effect of electrochemically roughened gold substrates on polymerization electrocatalysis of polypyrrole

In this work, electrochemical methods were used to prepare complexes with Au and Cl species on bulk Au substrates. Then the electrochemically roughened Au substrates were further heat-treated at different temperatures. The effect of temperatures used in heat treatments between 25 and 100 °C on electrocatalytical polymerization of polypyrrole (PPy) formed on the prepared gold substrates was first investigated. The result indicates that the optimally electrocatalytical capability of the heat-treated Au substrate for PPy polymerization is at 75 °C. Moreover, the autopolymerized PPy on the roughened Au substrate treated at 75 °C demonstrates the highest oxidation level and oxidation degree of 0.32 and 0.50, respectively. Primary results indicate that complexes with positively charged Au act as oxidants, and perchlorate and chloride ions act as dopants for the oxidation-polymerization of PPy.     

Oxidative polymerization of pyrrole in polymer matrix

The oxidative matrix polymerization of pyrrole (Py) by Ce(IV) in the presence of Polyacrylic acid (PAA) has been studied to obtain water-soluble and insoluble products. The role of the PAA, Pyrrole, and Ce(IV) concentration, order of component addition, the structure of polymer matrix (PAA, Hydroxy Ethyl Cellulose (HES), Poly-N-vinylpyrrolidone (PVP)], and model unit of PAA (propionic acid), on the polymerization system were investigated. Interaction of PAA with insoluble polypyrrole (PPy) and the interpolymer complex formation were investigated along with the aggregation of PPy onto the matrix polymer followed by spectral shifts. FTIR results of insoluble products obtained from the PAA–Py–Ce(IV) system and solubility of the system is explained in light of the mechanism of the polymerization of pyrrole on the polymer matrix. © 1995 John Wiley & Sons, Inc.     

Surface (XPS,SIMS) chemical investigation on poly(pyrrole‐3‐acetic acid) films electrosynthesized on Ti and TiAlV substrates for the development of new bioactive substrates

Electropolymerization of pyrrole‐3‐acetic acid was performed by cyclic voltammetry on titanium and Ti90Al6V4 substrates with the aim of developing a multilayer structure for applications in advanced biomaterials. The polymeric films obtained were characterized by both XPS and time‐of‐flight secondary ion mass spectrometry (ToF‐SIMS). Information on the poly(pyrrole‐3‐acetic acid) (PPy‐3‐acetic) surface structure was achieved by a detailed XPS analysis of C 1s and N 1s signals. The number of COOH groups was quantified by XPS coupled to a chemical derivatization reaction in which esterification with trifluoroethanol was exploited so that the presence of fluorine (or the CF₃ component in C 1s spectra) could be used as a marker for COOH groups. As a result, it was found that more than 90% of the monomer units along PPy‐3‐acetic chains bear carboxylic functionalities, of which 60% are protonated and 40% are present as carboxylate groups. Some decarboxylation occurs with film ageing. The PPy‐3‐acetic films were also investigated by ToF‐SIMS in the negative ion mode, thus obtaining, for the first time, interesting information on the structure of the top surface layers of a polymer belonging to the polypyrrole family. In particular, clusters of peaks related to PPy‐3‐acetic oligomers were detected and the decarboxylation phenomenon on top of the polymer surface was confirmed. Copyright © 2005 John Wiley & Sons, Ltd.     

A Brush‐Gel/Metal‐Nanoparticle Hybrid Film as an Efficient Supported Catalyst in Glass Microreactors

A polymer‐brush‐based material was applied for the formation and in situ immobilization of silver and palladium nanoparticles, as a catalytic coating on the inner wall of glass microreactors. The brush film was grown directly on the microchannel interior by means of atom‐transfer radical polymerization (ATRP), which allows control over the polymer film thickness and therefore permits the tuning of the number of nanoparticles formed on the channel walls. The wide applicability of the catalytic devices is demonstrated for the reduction of 4‐nitrophenol and for the Heck reaction.