Synthesis and characterization of spirobifluorene‐based polyimides

The synthesis and properties of organosoluble aromatic polyimides, containing spiro‐skeletal units in the polymer backbone on the basis of the spiro‐diamine monomer, 2,2′‐diamino‐9,9′‐spirobifluorene, are described. In the case of the spiro segment, the two fluorene rings are orthogonally arranged and connected through a tetrahedral bonding carbon atom, the spiro center. As a consequence, the polymer chain is periodically zigzagged with a 90° angle at each spiro center. This structural feature minimizes interchain interactions and restricts the close packing of the polymer chains, resulting in amorphous polyimides that have good solubility in organic solvents. Compared with their fluorene‐based cardo analogues, the spirobifluorene‐based polyimides have an improved solubility. Furthermore, the main‐chain rigidity of the polyimide appears to be preserved because of the presence of the spiro structure, which restricts the free segmental mobility. As a result, these polyimides exhibit a high glass‐transition temperature (T_g's) and good thermal stability. The T_g's of these polyimides were in the range of 287–374 °C, and the decomposition temperatures in nitrogen for a 10% weight loss occurred at temperatures above 570 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3615–3621, 2002     

Pd (II)‐catalyzed vinyl addition polymerization of novel functionalized norbornene bearing dimethyl carboxylate groups

Three novel functionalized polynorbornenes (PNB) with pendant dimethyl carboxylate group (carboxylates—acetate, propionate, and butyrate) are synthesized as a vinyl‐type with a palladium (II) catalyst in high yield. The effects of size of substitutents, molar ratio of monomer to catalyst, solvent polarity, reaction time, and temperature on the polymerization of exo‐norbornene dimethyl propionate were systematically investigated. The low molar ratio and temperature, as well as high polarity of solvent, and long reaction time, are favorable for the enhancement of the monomer conversion, especially, the solvent have an obvious effect on the catalyst activity. The resulting poly(cis‐norbornene‐exo‐2,3‐dimethyl carboxylates) (PNB‐dimethyl carboxylates) show good solubility in common organic solvent and high thermal stability up to 360 °C. The glass transition temperature was detected by DMA at 331, 324, and 318 °C for acetate, propionate, and butyrate, respectively. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3391–3399, 2007     

Synthesis and characterization of Y‐type polymers for second‐order nonlinear optical applications

A series of dicyanomethylene‐substituted polymers having Y‐type molecular architecture were synthesized by Knoevenagel condensation reaction. The polymers were found to be soluble in organic solvents like tetrahydrofuran and chloroform. From gel permeation chromatography, the molecular weights of the polymers were found to be in the range of 15,300–33,800 g/mol. Thermal analysis showed that the polymers were stable up to 350 °C with glass transition temperature (T_g) in the range of 129–212 °C. These polymers were found to form good optical quality films. The order parameter was calculated to be in the range of 0.01–0.48. Atomic force microscopy indicated prominent morphology changes due to alignment of dipoles after poling. By using Nd:YAG laser of 1064 nm, angular dependence and temperature dependence of second‐harmonic generation intensity were investigated. The geometry optimization, shape of polymers, and restricted torsion angle between acceptor and donor substituents (push–pull system) were calculated. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2013     

Synthesis of fluorene‐based high performance polymers. I. Poly(arylene thioether)s with excellent solubility and high refractive index

Several poly(arylene thioether)s ( PTEs ) containing a fluorene moiety were synthesized by the polycondensation of masked dithiols such as 9,9‐bis(4‐(N,N‐dimethyl‐S‐carbamoyl)phenyl)fluorene and various difluoroarenes. All PTEs were obtained in quantitative yields. The PTEs showed good thermal stability: the 10% weight loss temperature was over 480 °C under both nitrogen and air atmosphere by TGA, and glass temperature was within a range of 204–275 °C by DSC. Most PTEs exhibited remarkably high refractive index values in a range of 1.66–1.72 at 589 nm, whereas they had a very low degree of birefringence properties. Furthermore, the PTEs showed high solubility in ordinary organic solvents such as chloroform, N‐methylpyrrolidone, and tetrahydrofuran. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 3073–3082, 2007     

Preparation of aromatic polyimides highly soluble in conventional solvents

Several highly soluble polyimides were synthesized from various aromatic tetracarboxylic dianhydrides and an aromatic diamine containing tert‐butyl pendent groups [4,4′‐methylenebis(2‐tert‐butylaniline)]. All the polyimides showed excellent solubility in common solvents such as chloroform, tetrahydrofuran, and dioxane at room temperature. The number‐average molecular weight ranged from 3.6 × 10⁴ to 1.3 × 10⁵ according to gel permeation chromatography relative to a polystyrene standard, and the polydispersity index was between 1.9 and 2.5. The glass‐transition temperatures of the resulting polyimides ranged from 213 to 325 °C, as measured by differential scanning calorimetry, and little weight loss was observed up to 450 °C in N₂ by thermogravimetric analysis. These experimental data indicated that the tert‐butyl pendent groups reduced the interactions among polymer chains to improve their solubility in organic solvents without the loss of thermal stability. Transparent and flexible films of these polyimides were obtained via casting from solution. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 40: 229–234, 2002     

Blue light‐emitting poly(p‐phenylenevinylene) derivatives containing alternating conjugated segments and aliphatic spacers

Two new poly(p‐phenylenevinylene) derivatives were prepared by Heck coupling. They contained alternating conjugated segments on the basis of p‐distyrylbenzene and flexible nonconjugated spacers. The synthesized polymers P1 and P2 carried two m‐terphenyl of four tertbutyl pendants, respectively, per repeat unit. Both polymers were amorphous and exhibited satisfactory thermal stability. Polymer P1 displayed a limited solubility in common organic solvents, whereas P2 dissolved readily in these solvents. The glass‐transition temperature values were 128 °C for P1 and 37 °C for P2 . The polymers emitted blue or violet‐blue light with photoluminescent maxima at about 445 and 460 nm for solutions and thin films, respectively. The bulky pendants reduced their tendency to form aggregates. © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 1091–1098, 2003     

Pressure–Volume–Temperature properties of polyolefin liquids and their melt miscibility

The pressure–volume–temperature (P–V–T) properties of a number of metallocene-produced polyolefins were measured experimentally at 10 MPa ≤ P ≤ 200 MPa and 30°C ≤ T ≤ 220°C in a dilatometer-type P–V–T apparatus. These included ethylene copolymers typical of linear low density polyethylene, with several α-olefins as comonomers and a wide range of comonomer content. The experimental P–V–T data were correlated with the equations of state from the Sanchez–Lacombe and Flory–Orwoll–Vrij theories. The solubility parameter map of the polyolefins, at atmospheric pressure, was established on the basis of the thermodynamic data. As the temperature increases, the solubility parameter of the polyolefin decreases. The solubility parameters of copolymers of ethylene with propylene, butene, hexene, and octene under constant temperature are all more or less the same at equal weight percent of comonomer. As the incorporation of branches increases, the solubility parameter decreases. The melt miscibility of the polyolefin blends can be predicted to design various blend products for specific applications from this solubility parameter map. © 1999 John Wiley & Sons, Inc. J Polym Sci B: Polym Phys 37: 2835–2844, 1999     

Polyolefin soluble polyisobutylene oligomer‐bound metallophthalocyanine and azo dye additives

Metallophthalocyanines prepared with polyisobutyl (PIB) substituents have very high solubility in organic solvents including saturated hydrocarbons, toluene, and other low polarity organic solvents. In heptane, PIB‐bound metallophthalocyanines have solubility of about 0.1 g/mL at 25 °C, solubility values that are significantly higher than other substituted metallophthalocyanines. PIB terminally functionalized with metallophthalocyanines as well as PIB containing terminal azo dye groups also dissolve in molten hydrocarbon polymers like polyethylene or polypropylene. Thus, these highly chromogenic PIB‐bound dyes can be incorporated uniformly into the polyolefins to form colored polymer solids on cooling. Because only a low concentration of a highly hydrocarbon compatible dye is used, the crystallinity and thermal properties of the colored polyolefin products are not significantly affected. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 545–551     

Poly(arylene thioether)s containing 9,9′‐spirobifluorene moieties in the main chain: Masked dithiol‐based synthesis and excellent optical properties

Poly(arylene thioether)s ( PTEs ) containing 9,9′‐spirobifluorene moieties were synthesized in high yields from 9,9′‐spirobifluorene‐2,2′‐bis(N,N‐dimethylcarbamothioate) 4 as the masked dithiol and various difluoroarenes as electrophilic monomers. All PTEs showed high thermal stability: The 10% weight loss temperature as evaluated by thermogravimetric analysis was over 470 °C under both nitrogen and air atmospheres. The glass transition temperature estimated by DSC was in the range 210–270 °C. The PTEs showed high solubility in ordinary organic solvents, such as CHCl₃, NMP, and THF. Most PTEs exhibited remarkably high refractive indices ranging from 1.69 to 1.73 at 587.6 nm, whereas no or little birefringence was observed for the PTEs . © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 4192–4199, 2010     

Covalent surface functionalization of multiwalled carbon nanotubes through bergman cyclization of enediyne‐containing dendrimers

A method for covalent functionalization of multiwalled carbon nanotubes (MWCNTs) was developed using the free radicals generated through Bergman cyclization of enediyne‐containing compounds. Four enediyne‐bearing Frechet type dendrimers were synthesized in good quantities and characterized. Then, the enediyne‐containing molecules were reacted with MWCNTs in N‐methyl‐2‐pyrrolidinone at 206 °C under nitrogen. The structure and morphology of the resulting products were characterized by thermogravimetric analysis, ultraviolet–visible spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy. The dendrimer‐functionalized MWCNTs showed good solubility/dispersibility in common organic solvents and polymer solutions. They were used in the formation of polymer composites through electrospinning with polycaprolactone. The results confirmed the surface functionalization of MWCNTs. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Fluorene‐rich high performance polyesters: Synthesis and characterization of 9,9‐fluorenylidene and 2,7‐fluorenylene‐based polyesters with excellent optical property

Polyesters PEs containing high content of fluorene units in their backbones were synthesized from 9,9‐diarene‐substituted fluorene diols ( 1 ) and fluorene‐based diacid chlorides ( 2 ) by high temperature polycondensation at 185 °C in diphenyl ether. The molecular weights of the polyesters PE1‐PE5 were in a range of M_w 25,000–165,000. The polyesters displayed their high thermostability: the glass transition temperatures (T_g) by differential scanning calorimetry analysis ranged from 109 to 217 °C, while the 10% weight loss temperatures (T_d10) measured by thermogravimetric analysis were over 400 °C in nitrogen and 395 °C in air. The polyesters had good solubility in most common organic solvents such as chloroform and toluene and gave tough, transparent and flexible cast films. The transmittance of the films was over 80% in the wavelength range from 450 to 700 nm in any PEs . The PEs exhibited high refractive index values around 1.65, while they had very low degree of birefringence. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 2549–2556, 2008     

Ambipolar Transport in the Smectic E Phase of 2‐Propyl‐5′′‐Hexynylterthiophene Derivative over a Wide Temperature Range

5‐Hexyl‐5′′‐hexynyl‐2,2′:5′,2′′‐terthiophene exhibits the smectic E phase below 200 °C and does not crystallize when it is cooled to ?100 °C. Between 200 and ?100 °C, non‐dispersive transport is observed for holes and electrons with time‐of‐flight spectroscopy. Over the entire temperature range, the electron mobility is approximately twice as high as that of the hole. The hole and electron transport characteristics in the smectic phase below 0 °C are explained by the Gaussian disorder model, which was proposed for amorphous organic semiconductors. The disorder parameters, σ and Σ, are almost the same for holes and electrons. However, the pre‐exponential parameter μ₀ for the electron is twice as large as that for the hole, which can be attributed to the difference in the extension of the LUMO of the molecules. The energetic disorder σ is primarily determined by the disorder in the orientation of the permanent dipoles of liquid crystal molecules.     

Synthesis and characterization of novel polyimides with bulky pendant groups

New dianhydrides containing t‐butyl and phenyl pendant groups have been synthesized and used as monomers, together with commercial diamines, to prepare novel polyimides. The influence of the chemical structure of the monomers on their reactivity has been studied by quantum semiempirical methods. The polyimides have been characterized by FTIR and by NMR in the case of soluble polymers. The presence of pendant groups and the method used to imidize polyimide precursors greatly affected polymer properties such as solubility, glass transition temperature, thermal stability, and mechanical properties. As a rule, the novel polyimides showed better solubility in organic solvents than the parent polyimides. Glass transition temperatures in the range 250–270°C and decomposition temperatures over 520°C were observed for the set of current polymers. Tensile strengths up to 135 MPa and mechanical moduli up to 3.0 GPa were measured on films of the current polyimides. © 1999 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 37: 805–814, 1999     

Synthesis of fluorinated polybenzoxazoles with low dielectric constants

Two fluorinated aromatic bis(o‐aminophenol)s, 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′‐trifluoromethylphenyl)‐2,2,2‐trifluoroethane (6FAP) and 1,1‐bis(3′‐amino‐4′‐hydroxyphenyl)‐1‐(3′,5′‐ditrifluoromethylphenyl)‐2,2,2‐trifluoroethane (9FAP) were synthesized, which were allowed to polycondense with aromatic diacyl chlorides to afford the fluorinated aromatic polybenzoxazoles (PBOs) via a conventional two‐step procedure in which the low‐temperature solution polycondensation process was first performed to yield poly(o‐hydroxyamide)s (PHAs) followed by the thermal cyclodehydration to give the PBOs. Experimental results indicated that the PHAs had inherent viscosities in the range of 0.29–0.68 dL/g, showing excellent solubility in organic solvents. The PHAs could be thermally cyclodehydrated into the corresponding PBOs at 260–370 °C. The obtained PBOs exhibited enhanced glass‐transition temperature but decreased solubility with respect to the PHAs. The PBOs showed glass‐transition temperatures in the range of 315–337 °C and excellent thermal stabilities with 5% original weight‐loss temperatures (T₅) of >513 °C. Additionally, the PBO films had average refractive index of 1.5298–1.5656, birefringence of 0.0051–0.0092, and low dielectric constants of 2.57–2.70. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

The effect of structural variations on aromatic polyethers for high‐temperature PEM fuel cells

Three series of new aromatic polyether sulfones bearing phenyl, p‐tolyl or carboxyl side groups, respectively, and polar pyridine main chain groups were developed. Most of the polymeric materials presented high molecular weights and excellent solubility in common organic solvents. More importantly, they formed stable, self‐standing membranes that were thoroughly characterized in respect to their thermal, mechanical and oxidative stability, their phosphoric acid doping ability and ionic conductivity. Particularly, the copolymers bearing side p‐tolyl or carboxyl groups fulfill all necessary requirements for application as proton electrolyte membranes in high temperature fuel cells, which are glass transition temperatures higher than 220 °C, thermal stability up to 400 °C, oxidative stability, high doping levels (DLs) and proton conductivities of about 0.02 S/cm. Initial single fuel cell results at high temperatures, 160 °C or 180 °C, using a copolymer bearing p‐tolyl side groups with a relatively low DLs around 200 wt % and dry H₂/Air feed gases, revealed efficient power generation with a current density of 0.5 A/cm² at 500 mV. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Preparation and properties of novel benzoxazine and polybenzoxazine with maleimide groups

A benzoxazine compound with a maleimide group, 3‐phenyl‐3,4‐dihydro‐2H‐6‐(N‐maleimido)‐1,3‐benzoxazine (HPM‐Ba), was prepared from N‐(4‐hydroxyphenyl)maleimide, formaldehyde, and aniline. The chemical structure of HBM‐Ba was identified by FT‐IR, ¹H‐NMR, and elemental analysis. HPM‐Ba showed a melting point of 52–55 °C and good solubility in common organic solvents. HPM‐Ba showed a two‐stage process of thermal polymerization. The first stage arose from the polymerization of maleimide groups, and the second one was the ring‐opening reaction of benzoxazine groups. Fusible polymaleimides with a Tg of around 100 °C could be obtained by thermally polymerizing HPM‐Ba at 130 °C. Further polymerizing the polymaleimides at 240 °C resulted in a completely cured resin showing a Tg at 204 °C. Good thermal stability and self‐extinguishing behavior was observed with the cured polybenzoxazine resins. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 5954–5963, 2004     

Electrical and self‐heating properties of UHMWPE‐EMMA‐NiCF composite films

Conductive polymer composites (CPC) containing nickel‐coated carbon fiber (NiCF) as filler were prepared using ultra‐high molecular weight polyethylene (UHMWPE) or its mixture with ethylene‐methyl methacrylate (EMMA) as matrix by gelation/crystallization from dilute solution. The electrical conductivity, its temperature dependence, and self‐heating properties of the CPC films were investigated as a function of NiCF content and composition of matrix in details. This article reported the first successful result for getting a good positive temperature coefficient (PTC) effect with 9–10 orders of magnitude of PTC intensity for UHMWPE filled with NiCF fillers where the pure UHMWPE was used as matrix. At the same time, it was found that the drastic increase of resistivity occurred in temperature range of 120–200 °C, especially in the range of 180–200 °C, for the specimens with matrix ratio of UHMWPE and EMMA (UHMWPE/EMMA) of 1/0 and 1/1 (NiCF = 10 vol %). The SEM observation revealed to the difference between the surfaces of NiCF heated at 180 and 200 °C. Researches on the self‐heating properties of the composites indicated a very high heat transfer for this kind of CPCs. For the 1/1 composite film with 10 vol % NiCF, surface temperature (T_s) reached 125 °C within 40 s under direct electric field where the supplied voltage was only 2 V corresponding to the supplied power as 0.9 W. When the supplied voltage was enough high to make T_s beyond the melting point of UHMWPE component, the T_s and its stability of CPC films were greatly influenced by the PTC effect. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 1253–1266, 2009     

Click chemistry‐based synthesis of azo polymers for second‐order nonlinear optics

Four linear polymers containing pendant azo moiety were synthesized through click chemistry for second‐order nonlinear optical study. The polymers were found soluble in most of the polar organic solvents such as tetrahydrofuran (THF), chloroform, and dimethyl formamide (DMF). The polymers showed thermal stability up to 300 °C and glass transition temperatures (T_g) in the range of 120–140 °C. The molecular weights (M_w) of these polymers (measured by gel permeation chromatography) were in the range 37,900–55,000 g/mol. The polymers were found to form optically transparent films by solution casting from THF solution. Order parameters were calculated from UV–vis absorption spectra. The morphology changes in the films after poling were characterized by atomic force microscopy. The angular dependence, temperature dependence, and time dependence of second harmonic generation (SHG) intensity were obtained by using 1064 nm Nd:YAG laser. The SHG intensity remained unchanged up to 95 °C. At room temperature, it remained stable up to 8 days after initial drop of about 14%. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Preparation and properties of high‐pretilt‐angle polyimides based on an alicyclic dianhydride and long alkyloxy side‐group‐containing diamines

A series of polyimides were prepared by a solution polycondensation reaction between 3‐carboxylmethylcyclopentane‐1,2,4‐tricarboxylic dianhydride and 4‐alkyloxybenzene‐1,3‐diamines in N‐methyl‐2‐pyrrolidone and chemical imidization with triethylamine and acetic anhydride. These polyimides possess great organo‐solubility, high optical transparency, and high pretilt angles. They are soluble not only in strong polar aprotic organic solvents such as N‐methyl‐2‐pyrrolidone, N,N‐dimethylacetamide, N,N‐dimethylformamide, m‐cresol, and 1,4‐butyrolactone but also in common low‐boiling‐point solvents such as chloroform and tetrahydrofuran, and some are even soluble in acetone. They exhibit high transparency at wavelengths greater than 320 nm. They can generate pretilt angles greater than 5°, and some can even achieve pretilt angles greater than 10°. The pretilt angle of a polyimide increases with the increasing length of the alkyloxy side group. The polyimides possess glass‐transition temperatures between 180 and 230 °C and thermal decomposition temperatures (onset temperatures) of about 435 °C. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1943–1950, 2000     

Dicarboxylic imide‐substituted poly(p‐phenylene vinylenes) with high electron affinity

Synthesis of n‐type organic semiconductors with high electron mobilities, good environmental stability, and good processability is an urgent task in current organic electronics. This is because most of π‐conjugated materials are p‐type and prefer to transport positive hole carriers. In this article, a series of new dicarboxylic imide‐substituted poly(p‐phenylene vinylenes) (DI‐PPVs) were first synthesized. They exhibited a high electron affinity of 3.60 eV and thus are able to transport electrons. The polymers showed tunable solubility in common organic solvents and high chemical and thermal stability. They remain rigidity of the PPV backbone, and strong interchain π‐stacking was observed in thin films by X‐ray diffraction measurement. All these suggested that these polymers could serve as good candidates as n‐type semiconductors in organic electronic devices such as n‐channel field‐effect transistors and all polymer‐based solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 186–194, 2010