Studies on thermal decomposition of electrochemically oxidized glass-like carbon

Glass-like carbon (GC) tiles were electrochemically oxidized in 1 mol·dm^?3 H₂SO₄ solution at a potential of 2.3 V/SCE. The surfaces of the oxidized samples were examined by scanning electron microscopy (SEM). The solid oxidation products were studied by derivatographic (TG, DTG and DTA) and elemental analyses. The solid products of electrochemical oxidation of GC, with the general formula C₈O_4.2H_2.3 were thermolabile and revealed properties similar to those of graphite oxide. They are hydrophylic and their thermal decomposition proceeds in three steps: (i) evaporation of-chemisorbed water (320–400 K), (ii) exothermic decomposition of graphite oxide (370–430 K), and (iii) gradual decomposition of the oxidation products (>430 K).     

Analysis of nitromethane thermal decomposition at low temperatures

The thermal decomposition of nitromethane (NM) over the temperature range from 580 to 700 K at pressures of 4 Torr to 40 atm was analyzed. On the basis of literature data, with the use of theoretical transitional curves of the modified Kassel integral, the rate constants k of NM decomposition at the upper pressure limit were determined. The values thus obtained are in good agreement with the results of extrapolation of the high-temperature (1000–1400 K) k _{1, ∞} values to lower temperatures. The reasons for which the NM decomposition rate constants differ by two orders of magnitude at low temperatures are considered. A general expression for the NM decomposition rate constant at the upper pressure limit over the 580–1400 K temperature range was determined: k _{1, ∞} = (1.8 ± 0.7) × 10¹⁶ exp((?58.5 ± 2)/R _T ) s^?1. These data disprove the hypothesis that a nitro-nitrite rearrangement takes place during the NM decomposition at low temperatures.     

Thermochemical behaviour of lanthanum complexes of 2-ethylhexyl phosphoric acid

The thermochemical behaviour of solid-state complexes of lanthanum with mono-(2-ethylhexyl) phosphoric acid (H₂B) (La(HB)₃·1.5H₂O and La₂B₃·3H₂O) was studied. The thermal decomposition of these complexes proceeds without melting to yield La(PO₃)₃ and a mixture of La(PO₃)₃ and LaPO₄, respectively. La(HB)₃1.5H₂O decomposes via dehydration (323–383 K), condensation of the OH-groups with formation of a diphosphate structure (383–458 K) and a stepwise degradation of the hydrocarbon chains (443–565 K). The dehydration of La₂B₃·3H₂O (333–433 K) is followed by decomposition of the hydrocarbon group. From a combination of the present results with previous data [1], it was concluded that the temperatures and mechanisms of the decomposition of the hydrocarbon part of the lanthanide complexes of (2-ethylhexyl) phosphoric acids depend on the nature of the lanthanide, the atmosphere, and the structure of the complexes.     

Studies on high-temperature thermal transformation and dielectric property of aluminum–chromium phosphates

High-temperature thermal transformation of aluminum–chromium phosphates has been investigated by means of DSC–TG, IR, and XRD analysis. The relative dielectric constant and thermal decomposition were measured and discussed. The results show that crystallization and thermal decomposition started at about 1,273 K, only AlPO₄ and Cr₂O₃ have been found at 1,873 K due to the decomposition of PO ₃ ^? , P₂O ₇ ^2? , and PO ₄ ^3? . The relative dielectric constant is fluctuant.     

“In situ” measurements of the influence of temperature on the decomposition of H2Na2EDTA adsorbed on alumina

The adsorption of H₂Na₂EDTA (disodium salt of ethylenediaminetetraacetic acid) on gamma alumina and its thermal degradation has been investigated by transmission IR. The IR spectra in the 2000–1200 cm⁻¹ region of the supported complexone were analysed in the temperature range 393–673 K utilising IR cell reactor applied for in situ measurements. Based on the observed changes, it can be stated that thermal decomposition of adsorbed complexone occurs in the temperature range of 473–493 K.     

Thermal analysis of 5′-deoxy-5′-iodo-2′,3′-O-isopropylidene-5-fluorouridine

The melting temperature, melting enthalpy, and specific heat capacities (C _p) of 5′-deoxy-5′-iodo-2′,3′-O-isopropylidene-5-fluorouridine (DIOIPF) were measured using DSC-60 Differential Scanning Calorimetry. The melting temperature and melting enthalpy were obtained to be 453.80 K and 33.22 J g^?1, respectively. The relationship between the specific heat capacity and temperature was obtained to be C _p/J g^?1 K^?1 = 2.0261 – 0.0096T + 2 × 10^?5 T ² at the temperature range from 320.15 to 430.15 K. The thermal decomposition process was studied by the TG–DTA analyzer. The results showed that the thermal decomposition temperature of DIOIPF was above 487.84 K, and the decomposition process can be divided into three stages: the first stage is the decomposition of impurities, the mass loss in the second stage may be the sublimation of iodine and thermal decomposition process of the side-group C₄H₂O₂N₂F, and the third stage may be the thermal decomposition process of both the groups –CH₃ and –CH₂OCH₂–. The obtained thermodynamic basic data are helpful for exploiting new synthetic method, engineering design, and commercial process of DIOIPF.     

Thermal analysis of manganese(II) complexes of general formula (Bu4N)2[MnBrnCl4−n]

Thermal decomposition of compounds consisting of tetrahalogenomanganese(II) anions, [MnBr_nCl_4?n]^2? (n = 0–4), and a tetrabutylammonium cation has been studied using the DSC, TG-FTIR, TG–MS and DTA techniques. The measurements were carried out in an argon and static air atmospheres over the temperature ranges 173–450 K (DSC) and 300–1073 K (TG). Solid products of the thermal decomposition were identified by FT-FIR spectroscopy as well as X-ray powder diffractometry.     

Kinetics of γ-alumina chlorination by phosgene

The kinetics of the reaction between γ-Al₂O₃ and COCl₂ have been studied by isothermal TG measurements in the temperature range 585–1085 K. The influence of the partial pressure of COCl₂ on the reaction rate was investigated at 648, 673 and 698 K in the 10⁴–10⁵ Pa range, using N₂ as a diluting gas. The reaction seems to proceed in the chemical control region below 675 K. Above this temperature, however, diffusional processes and decomposition of COCl₂ are considered to affect the reaction rate. In the chemical control region an apparent order of reaction of 0.75 in respect of COCl₂ and an apparent activation energy of 128–135 kJ mole^?1 were found for the chlorination process.     

Thermal decomposition rate of N2O5 measured by cavity ring‐down spectroscopy

The thermal decomposition rate of N₂O₅ in 760 Torr of air as a function of temperature between 314 and 348 K has been investigated using the technique of pulsed laser cavity ring-down spectroscopy (CRDS) detection of NO₃ radicals at 662 nm. The Arrhenius expression of the thermal decomposition rates determined by the CRDS experiments, which is incorporated with literature values down to 263 K, is given by 1.36 × 10¹⁵ exp{(−11300 ± 200)/T} s⁻¹ over the temperature range 263–348 K. © 2008 Wiley Periodicals, Inc. Int J Chem Kinet 40: 679–684, 2008     

Thermal decomposition of 1,2 butadiene

The thermal decomposition of 1,2 butadiene has been studied behind reflected shock waves over the temperature and total pressure ranges of 1300–2000 K and 0.20–0.55 atm using mixtures of 3% and 4.3% 1,2 butadiene in Ne. The major products of the pyrolysis are C₂H₂, C₄H₂, C₂H₄, CH₄ and C₆H₆. Toluene was observed as a minor product in a narrow temperature range of 1500–1700 K. In order to model successfully the product profiles which were obtained by time-of-flight mass spectrometry, it was necessary to include the isomerization reaction of 1,2 to 1,3 butadiene. A reaction mechanism consisting of 74 reaction steps and 28 species was formulated to model the time and temperature dependence of major products obtained during the course of decomposition. The importance of C₃H₃ in the formation of benzene is demonstrated.     

Low-Temperature Heat Capacities and Thermodynamic Properties of Octahydrated Barium Dihydroxide,Ba（OH）2·8H2O（s）

Low-temperature heat capacities of octahydrated barium dihydroxide, Ba（OH）2·8H2O（s）, were measured by a precision automated adiabatic calorimeter in the temperature range from T=78 to 370 K. An obvious endothermic process took place in the temperature range of 345-356 K. The peak in the heat capacity curve was correspondent to the sum of both the fusion and the first thermal decomposition or dehydration. The experimental molar heat capacifies in the temperature ranges of 78-345 K and 356-369 K were fitted to two polynomials. The peak temperature, molar enthalpy and entropy of the phase change have been determined to be （355.007±0.076） K, （73.506±0.011） kJ·ol^-1 and （207.140±0.074） J·K^-1·mol^-1, respectively, by three series of repeated heat capacity measurements in the temperature region of 298-370 K. The thermodynamic functions, （Hr-H298.15 k ）and （Sr-S298.15k）, of the compound have been calculated by the numerical integral of the two heat-eapacity polynomials. In addition, DSC and TG-DTG techniques were used for the further study of thermal behavior of the compound. The latent heat of the phase change became into a value larger than that of the normal compound because the melfing process of the compound must be accompanied by the thermal decomposition or dehydration of 71-120.     

Hydrogen Promoted Decomposition of Ammonium Dinitramide: an ab initio Molecular Dynamics Study

Thermal decomposition of a famous high oxidizer ammonium dinitramide (ADN) under high temperatures (2000 and 3000 K) was studied by using the ab initio molecular dynamics method.Two different temperature-dependent initial decomposition mechanisms were observed in the unimolecular decomposition of ADN, which were the intramolecular hydrogen transfer and N-NO₂ cleavage in N (NO₂)^-.They were competitive at 2000 K, whereas the former one was predominant at 3000 K.As for the multimolecular decomposition of ADN, four different initial decomposition reactions that were also temperature-dependent were observed.Apart from the aforementioned mechanisms, another two new reactions were the intermolecular hydrogen transfer and direct N-H cleavage in NH₄⁺.At the temperature of 2000 K, the N-NO₂ cleavage competed with the rest three hydrogen-related decomposition reactions, while the direct N-H cleavage in NH₄⁺ was predominant at 3000 K.After the initial decomposition, it was found that the temperature increase could facilitate the decomposition of ADN, and would not change the key decomposition events.ADN decomposed into small molecules by hydrogen-promoted simple, fast and direct chemical bonds cleavage without forming any large intermediates that may impede the decomposition.The main decomposition products at 2000 and 3000 K were the same, which were NH₃, NO₂, NO, N₂O, N₂, H₂O, and HNO₂.     

Gas-phase thermal decomposition of peroxy-N-butyryl nitrate

The gas-phase thermal decomposition rate of peroxy-n-butyryl nitrate (n-C₃H₇C(O)OONO₂, PnBN) has been measured at ambient temperature (296 K) and 1 atm of air relative to that of peroxyacetyl nitrate (CH₃C(O)OONO₂, PAN) using mixtures of PAN (14–19 ppb), PnBN (22–46 ppb), and nitric oxide (1.35–1.90 ppm). The PnBN/PAN decomposition rate ratio was 0.773 ± 0.030. This ratio, together with a literature value of 3.0 × 10^?4 s^?1 for the thermal decomposition rate of PAN at 296 K, yields a PnBN thermal decomposition rate of (2.32 ± 0.09) × 10^?4 s^?1. The results are briefly discussed by comparison with data for other peroxyacyl nitrates and with respect to the atmospheric persistence of PnBN. © 1994 John Wiley & Sons, Inc.     

Study of the thermal decomposition of historical metal threads

A complex of copper perchlorate coordinated with imidazole Cu(C₃N₂H₄)₄(ClO₄)₂ was synthesized and characterized by X-ray single-crystal diffraction. The complex is centrosymmetric in the monoclinic P2(1)/c space group. The low-temperature molar heat capacities and thermodynamic properties of the complex were studied with adiabatic calorimetry (AC). The thermodynamic functions [H _T–H _298.15] and [S _T–S _298.15] were derived in the temperature range from 80 to 370 K with temperature interval of 5 K. Thermal decomposition behavior of the complex in nitrogen atmosphere was studied by thermogravimetric (TG) analysis and differential scanning calorimetry (DSC). The mechanism of the decomposition was deduced to be the breaking up the two Cl–O bonds of the Cl–O–Cu and the Cu–N bonds of the imidazole rings in succession.     

The influence of oxygen pressure on the kinetics of the thermal decomposition of Co3O4

The kinetics of the thermal decomposition of Co₃O₄ has been examined in the 1123–1200 K temperature and 2.66–20.73 kPa oxygen pressure range. The kinetics of this process has been deseribed in terms of a mixed-control model of reaction. The values of activation energies of diffusion and chemical reaction as well as the observed activation energy have been given. The strong dependence of the decomposition rate on temperature and oxygen pressure has been explained.     

Synthesis of CeO2 by thermal decomposition of oxalate and kinetics of thermal decomposition of precursor

CeO₂ was synthesized by calcining Ce₂(C₂O₄)₃·8H₂O above 673 K in air. The precursor and its calcined products were characterized using thermogravimetry and differential scanning calorimetry, Fourier transform infrared spectra, X-ray powder diffraction, scanning electron microscopy, and UV–Vis absorption spectroscopy. The result showed that cubic CeO₂ was obtained when the precursor was calcined above 673 K in air for 2 h. The UV–Vis absorption spectroscopy studies showed that superfine CeO₂ behaved as an excellent UV-shielding material. The thermal decomposition of the precursor in air experienced two steps, which are: first, the dehydration of eight crystal water molecules, then the decomposition of Ce₂(C₂O₄)₃ into cubic CeO₂. The values of the activation energies associated with the thermal decomposition of Ce₂(C₂O₄)₃·8H₂O were determined based on the Starink equation.     

Computational Study on the Thermal Decomposition of Phenol‐Type Monolignols

A detailed chemical kinetic model has been developed to theoretically predict the pyrolysis behavior of phenol‐type monolignol compounds (1‐(4‐hydroxyphenyl)prop‐2‐en‐1‐one, HPP; p‐coumaryl alcohol, 3‐hydroxy‐1‐(4‐hydroxyphenyl)propan‐1‐one, HHPP; 1‐(4‐hydroxyphenyl)propane‐1,3‐diol, HPPD) released from the primary heterogeneous pyrolysis of lignin. The possible thermal decomposition pathways involving unimolecular decomposition, H‐addition, and H‐abstraction by H and CH₃ radicals were investigated by comparing the activation energies calculated at the M06–2X/6–311++G(d,p) level of theory. The results indicated that all phenol‐type monolignol compounds convert to phenol by side‐chain cleavage. p‐Coumaryl alcohol decomposes into phenol via the formation of 4‐vinylphenol, whereas HPP, HHPP, and HPPD decompose into phenol via the formation of 4‐hydroxybenzaldehyde. The pyrolytic pathways focusing on the reactivity of the hydroxyl group in HPP and producing cyclopentadiene (cyc‐C₅H₆) were also investigated. The transition state theory (TST) rate constants for all the proposed elementary reaction channels were calculated at the high‐pressure limit in the temperature range of 300–1500 K. The kinetic analysis predicted the two favorable unimolecular decomposition pathways in HPP: the one is the dominant channel below 1000 K to produce cyc‐C₅H₆, and the other is above 1000 K to yield phenol (C₆H₅OH).     

Kinetics of thermal decomposition of a synthetic K–H3O jarosite analog

The thermal decomposition kinetics of a synthetic K–H₃O jarosite analog was determined from thermogravimetric analysis at various heating rates in air. A thermal decomposition mechanism was proposed based on X-ray analysis of partially decomposed material and distinct features observed during thermal decomposition analysis. The decomposition path is complex. The material was treated as a composite of K-jarosite, H₃O-jarosite, and a “vacancy component”. The evolution of (OH)^? and SO₃ from these individual components was modeled. The decomposition is broken into subreactions according to distinct features in the thermoanalytical measurements. The subreactions are arranged sequentially and in parallel according to the evolution of the participating phases. A set of associated apparent activation energies was determined using isoconversion analysis. Kinetic triplets were assigned to each subreaction. A reasonable match with the observed decomposition was achieved by varying pre-exponential factors.     

Differential scanning calorimetry of sodium and potassium nitrates and nitrites

Differential scanning calorimetry (DSC) experiments were performed with NaNO₃, KNO₃, (Na,K)NO₃, NaNO₂ and KNO₂ over the temperature range 350–990 K. Endothermic peaks, indicative of decomposition reactions, were observed to occur in the single salts above their melting points. The equimolar mixture of sodium and potassium nitrate did not decompose in the temperature range specified. The nitrites began to decompose at 800±10 K. Sodium nitrate began to decompose at 840±10 K and potassium nitrate began to decompose at 820±20 K. These results were compared with previously reported differential thermal analysis investigations of NaNO₃ and KNO₃.     

Kinetics of the initiation step of the thermal decomposition of SiCl4

The initiation reaction of the thermal decomposition of silicon tetrachloride was studied behind reflected shock waves at temperatures between 1550 K and 2370 K and pressures between 1 and 1.5 bar. Atomic resonance absorption spectrometry (ARAS) was applied for time-resolved measurements of H atoms at the L_α-line in SiCl₄/H₂/Ar systems. Additional experiments were performed in the SiCl₄/Ar system following the absorption of SiCl₄ at the L_α-line. Rate coefficients for the reaction (RI) were determined to be: The choice between two possible alternatives of the first decomposition step, namely elimination of either Cl₂ or Cl, has been made in favor of the second reaction on the basis of kinetic and energetic considerations. © 1997 John Wiley & Sons, Inc. Int J Chem Kinet 29: 415–420, 1997.