基于尼古丁对胆碱氧化酶的抑制作用测定尼古丁的研究

基于尼古丁对胆碱氧化酶(CHOD)的抑制作用,将胆碱氧化酶电极用于微量尼古丁的测定。酶电极制作中,先在铂电极表面修饰一层壳聚糖膜,再用戊二醛交联CHOD。采用这种酶固定化方法,电极在4. 0×10-6 ~ 3×10-3 mol/L胆碱的浓度范围呈线性关系。探讨了工作电位、pH、底物浓度等实验条件对酶电极性能及抑制过程中响应电流的影响,测定了电极的重现性、干扰及使用寿命。电极检测尼古丁的线性范围为1. 5×10-5 ~3×10-3 mol/L;检出限为1. 25×10-5 mol/L。将电极用于实际样品烟草中尼古丁回收率的测定,结果良好。     

基于Nafion-氧化石墨烯复合物/硫堇/纳米金构建过氧化氢传感器的研究

利用Nafion(全氟聚苯乙烯磺酸溶液)-氧化石墨烯复合物、硫堇和纳米金构建了H2O2酶传感器。首先将氧化石墨烯分散在体积分数0.2%Nafion溶液中制得Nafion-氧化石墨烯的复合物,并将其固定在玻碳电极表面,通过静电吸附将带正电荷的硫堇吸附到Nafion-氧化石墨烯复合膜修饰的玻碳电极表面,再利用静电吸附将纳米金修饰于电极上,通过纳米金来固定辣根过氧化物酶从而制得H2O2传感器。用循环伏安法和计时电流法考察该修饰电极的电化学特性。H2O2浓度为5.5×10-6~1.0×10-3mol/L时,酶电极的响应电流值与H2O2的浓度呈良好的线性关系,检出限为1.80×10-6mol/L。     

基于壳聚糖-纳米金/纳米普鲁士蓝/L-半胱氨酸修饰的 葡萄糖传感器的研究

在金电极表面修饰一层L-半胱氨酸,再利用静电吸附作用固定纳米普鲁士蓝(nano-PB),然后利用壳聚糖-纳米金复合膜将葡萄糖氧化酶(GOD)固定于修饰电极表面,制成新型的葡萄糖传感器.通过交流阻抗技术,循环伏安法和计时电流法考察了电极的电化学特性.在优化的实验条件下,该传感器在葡萄糖浓度为3.0×10-6～1.0×10-3 mol/L范围内有线性响应,检测下限为1.6×10-6 mol/L.此外该传感器具有响应快、稳定性好和选择性良好的特点,能有效排除常见干扰物质如抗坏血酸、尿酸等对测定的影响.     

基于壳聚糖膜固定双酶的胆碱传感器的研究

提出了一种基于壳聚糖膜固定辣根过氧化物酶 胆碱氧化酶的胆碱传感器的制备方法。该传感器以电聚合于玻碳电极的硫堇作为电子传递介体,在pH6. 8,外加电压-0. 2V(vs.SCE)条件下,其峰电流与浓度范围 5. 0×10-5 ~3. 0×10-3 mol/L的胆碱呈良好的线性响应;检出限为 1. 0×10-5 mol/L。传感器有良好的选择性和稳定性,使用一月后,仍能保持其初始活性的 80%。     

基于层层静电吸附天青Ⅰ和纳米金固定过氧化物酶生物传感器的研究

在玻碳电极(GCE)上,构造了一种以对氨基苯磺酸电聚合膜(PABSA)为基底,利用层层静电自组装技术固定多层天青Ⅰ(AI)和纳米金(nano-Au)制备的复合薄膜(nano-Au/AI)n,然后通过静电吸附辣根过氧化物酶(HRP)制得过氧化氢生物传感器[HRP/(nano-Au/AI)n/PABSA/GCE].采用循环伏安法和计时电流法考察了该传感器的电化学性质,并且研究了该修饰电极对H2O2的催化还原作用.在优化的实验条件下,该传感器的响应电流与其浓度在3.5×10-6～3.6×10-3 mol/L范围内呈现良好的线性关系,检出限为1.2×10-6 mol/L.该传感器的米氏常数为1.5 mmol/L,表明所固定的酶具有较高的生物活性.     

三氧化二铝溶胶-凝胶固定过氧化氢生物传感器

三氧化二铝溶胶凝胶将辣根过氧化物酶和硫堇同时固定在玻碳电极上,紫外-可见光谱结果表明酶在固定过程中生物活性保持得较好.传感器在pH 7.0外加电压为-0.22 V条件下,对过氧化氢浓度为1.76×10-3～5.5×10-2 mol/L的范围内呈线性响应,检出限为1.1×10-4 mol/L.传感器的选择性和稳定性较好,使用3个星期后,仍能保持其初始活性的80%.     

以高氯酸·三-2,2''''-联吡啶合钴(Ⅲ)为介体的葡萄糖氧化酶传感器的研究

以聚乙烯醇缩丁醛为固定葡萄糖氧化酶(GOD)的载体,将GOD附在铂丝电极上并采用高氯酸·三-2,2'-联吡啶合钴(Ⅲ)[Co(bpy)3(ClO4)3]作为电子媒介体制得了电流型葡萄糖酶电极.讨论了溶解性媒介体Co(bpy)3(ClO4)3的浓度、溶液的pH值和温度对该电极电流响应的影响.该介体型葡萄糖传感器在优化的实验条件下,对葡萄糖表现出良好的响应特性,如响应快、重复性和稳定性好,传感器线性范围为6.0×10-6～1.1×10-4mol/L,检出限为3.0×10-6mol/L.将该电极用于人血清中葡萄糖测定,其结果与传统方法测得的结果一致.     

壳聚糖/聚乙烯吡咯烷酮固定辣根过氧化物酶的过氧化氢生物传感器

用一种新型的壳聚糖(CS)/聚乙烯吡咯烷酮(PVP)复合膜在玻碳电极(GCE)上固定辣根过氧化物酶(HRP)。以乙二醛作交联剂,二茂铁(Fc)作媒介体,制备过氧化氢生物传感器。红外光谱表明:CS与PVP交联形成了一种新的高聚物,实验结果证明该聚合物适合辣根过氧化物酶的固定。该传感器对于H2O2的电流响应在5 s内即可达到最大,线性范围为6.0×10-6~1.7×10-4mol/L;检出限为2.5×10-6mol/L。该传感器的检测灵敏度为62.5μA/mmol/L。     

聚亚甲基蓝和纳米金修饰玻碳电极的葡萄糖生物传感器

用循环伏安法在玻碳电极上电聚合一层稳定的亚甲蓝聚合物膜,研究了这层膜在0.1mol/L磷酸缓冲溶液(pH7.0)中的电化学性质。用纳米金溶胶与聚乙烯醇缩丁醛(PVB)构成复合固酶基质,采用溶胶-凝胶法固定葡萄糖氧化酶(GOD)于亚甲蓝修饰的玻碳电极表面,制成了新型葡萄糖生物传感器。实验发现,加入纳米金后提高了酶电极对葡萄糖的电流响应,所制备的传感器具有响应快、灵敏度高、稳定性好,对葡萄糖的线性响应范围为1×10-6~3×10-3mol/L,检出限为5×10-7mol/L。并具有抗尿酸、抗坏血酸干扰的特点。     

天青Ⅰ为电子媒介体金纳米颗粒修饰葡萄糖生物传感器

用纳米金溶胶与聚乙烯醇缩丁醛(PVB)构成复合固酶基质,采用溶胶凝胶法固定葡萄糖氧化酶(GOx)于铂金电极表面,并在葡萄糖溶液中加入天青Ⅰ作为电子媒介体,制成了新型葡萄糖生物传感器。实验证明,葡萄糖氧化酶吸附在纳米金颗粒表面上稳定且保持其生物活性;而电子媒介体的存在,显著提高了传感器的响应灵敏度。该传感器对葡萄糖响应的线性范围为2.5×10-5～7.5×10-3mol/L;检出限为8.5×10-6mol/L(S/N=3)。该生物传感器用于人体血清中的葡萄糖测定,结果令人满意。     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.