Cu-Fe基催化剂上CO加氢反应过程中物相的转化行为

研究了Cu-Fe基催化剂上CO加氢反应过程中各组分尤其是铁的体相和表面微观结构的转化行为.通过XRD、Mssbauer谱、XPS和Raman光谱等表征手段全程跟踪铁形态的变化.结果表明,还原后体相的铁发生了明显的碳化,物相以Fe3O4和χ-Fe5C2为主,随着反应温度的升高,χ-Fe5C2的含量出现最大值.而还原后催化剂表面没有检测到明显的铁的碳化.这种表面性质与体相的差异来源于铁独特的还原方式,这种还原方式造成锌和锰等组分在催化剂表面富集.而在反应过程中,系统中还原/氧化气氛的变化导致铁组分在催化剂表面富集.还原后自由碳原子在催化剂表面沉积,并随着反应的进行,碳原子的形态发生变化,显著抑制了Cu和Fe之间的协同作用,削弱了Cu-Fe基催化剂的链增长能力.     

制备方法对Fe/NCNTs催化剂结构及费托反应性能的影响

以碳氮纳米管(NCNTs)为载体,利用氮的锚定作用,采用三种不同的制备方法(等体积浸渍法、胶体法和沉积沉淀法)方便地构建了负载铁物种的Fe/NCNTs催化剂.系统考察了制备方法对催化剂的结构及费托反应性能的影响.结果表明,制备方法影响铁纳米粒子的粒度和分布、催化剂的还原和碳化行为,使催化剂表现出不同的催化性能.等体积浸渍法得到分散性较好、粒径小和分布窄[(8±4)nm]、容易还原和碳化的催化剂,反应中呈现出最高的低碳烯烃选择性、催化活性和稳定性.胶体法得到了形貌各异的粒子,反应中活性相易被氧化使得催化剂活性及稳定性较差.沉积沉淀法得到了粒径过大、难以还原和碳化的粒子,反应15 h后催化剂活性及稳定性急剧下降.该研究为利用氮掺杂碳纳米材料作为载体设计和开发高性能的费托合成催化剂提供了有益参考.     

铁／锌催化剂的物相结构及其还原行为的穆斯堡尔谱研究

以Mossbauer谱为手段,研究了用于F-T合成的Fe/Zn催化剂的物相结构,并考察了组成及制备方法的影响,同时还对其还原、碳化行为进行了探讨.发现锌对铁的还原有抑制作用,它能够稳定二价铁不被进一步还原.研究还表明,我们所研制的Fe/Zn催化剂是一种高分散度的铁锌化合物,室温下具有超顺磁特性.     

F-T合成Fe/Cu/K/Al2O3催化剂的结构性质、还原及碳化行为

采用连续共沉淀与喷雾干燥成型技术相结合的方法制备了微球状Fe/Cu/K/Al2O3催化剂, 结合TG、N2物理吸附、XRD、H2-TPR、CO-TPR、Mossbauer谱等表征手段, 研究焙烧温度对Fischer-Tropshc (F-T)合成铁基催化剂的结构性质、还原行为和碳化行为的影响. 结果表明, 较高的焙烧温度有利于碳酸盐的分解和结晶水的脱除, 促进了催化剂的还原. 随着焙烧温度的进一步升高, 催化剂的比表面积减小, 平均孔径增大, α-Fe2O3晶粒的粒径增大, 催化剂中金属与载体的相互作用增强, 从而削弱了CuO、K2O助剂的作用, 严重抑制了催化剂的还原和碳化.     

铁基费托合成催化剂相变调控及反应性能

在Fe基模型催化剂上,通过先深度还原后控制碳化的方法实现了物相结构的调控.采用X射线衍射、穆斯堡尔谱、程序升温脱附技术和激光拉曼光谱等方法表征了催化剂还原和反应前后的物化性质,并在固定床反应器中考察了不同条件活化后催化剂上费托反应性能.结果表明,H₂还原后的催化剂主要由α-Fe相组成,且随着还原温度的提高,α-Fe相的致密程度增加,平均晶粒尺寸增加,稳定性提高;再采用乙烯对H₂还原后催化剂进行碳化,可有效控制α-Fe的碳化速度,使碳化过程主要发生在Fe晶粒表层,同时改变了催化剂在反应过程中的物相变化,乃至其催化性能.与纯H₂或合成气气氛活化的催化剂相比,采用先H₂还原后乙烯碳化的预处理方法能够明显提高催化剂的活性和稳定性.     

Fe1-xO基氨合成催化剂高活性机理初探

 由Fe1-xO催化剂的发现所引伸的新课题及其中潜在的科学暗示,特别是Fe1-xO基催化剂的高活性机理有待深入研究. 本文根据催化剂的还原性能和表面性质及其与催化活性的关联,从Fe1-xO的化学和物理性质出发,对Fe1-xO催化剂的高活性机理提出了一些初步认识. 催化剂前驱体由Fe3O4改变为Fe1-xO,首先使得催化剂的还原易于进行,还原温度降低,还原速度加快,还原出水量减少; 其次,改变了助催化剂在催化剂中的分布,从而改变了还原后催化剂的表面性质如表面酸覆盖度和碱覆盖度及其相对比例,形成了表面酸碱协同作用,促进了表面重构,降低了N2的脱附活化能,削弱了H2的强化学吸附. 这些变化导致催化剂活性提高,同时这些变化都是由Fe1-xO的化学和物理性质引起的,只有维氏体单独存在于催化剂中催化剂才具有高活性. 提出了H2的强化学吸附与催化剂表面酸碱度有关的观点.     

碳化铁催化剂的制备及其对CO加氢的催化活性

 以Fe2O3为原料,采用两种预处理方法制备了碳化铁催化剂. 结果表明,直接在CO气氛下进行碳化处理,或者以H2预还原后再用CO进行碳化处理均可以制备出碳化铁催化剂. 碳化温度是制备过程中的关键因素. 对于Fe2O3样品,较适宜的碳化温度是350 ℃,而对于添加了K助剂的样品,只有经H2预还原处理后再于350 ℃用CO碳化处理4 h才能将样品完全转化为Fe5C2. 在CO加氢的评价实验中,碳化铁催化剂表现出很高的催化活性,生成的烃类产物中主要是饱和烷 烃,未检测到乙烯的生成. 而在K改性的催化剂上反应产物中烯烃的含量明显提高.     

固体炭对一氧化氮低温催化解离还原反应的影响——Ⅱ.复合催化剂中铁在载体炭上化学形态的研究

用~(57)Fe穆斯堡尔谱研究了炭载型复合催化剂中铁化学形态随温度的变化,及各活性组分、助剂对铁化学形态的影响;并通过ESR谱考察了复合催化剂中不同活性组分对铁在载体炭表面电子特性的影响。研究结果表明,复合催化剂中各活性组分、助剂和载体炭与铁之间存在着强相互作用。在350～650℃,载体炭可将铁从Fe_2O_3还原到Fe_3O_4、FeO、α-Fe和生成炭化铁。活性组分Cu和助剂K可改变催化剂中铁周围的电子密度,促进铁在载体炭上从高价态向低价态还原。同时还发现催化剂中Na和Cr对铁有很强的助分散作用。     

铁基氮掺杂碳纳米管制备及其电催化性能

利用化学原位聚合法制备聚吡咯包覆碳纳米管,然后以硫酸亚铁铵盐为铁前驱体,采用液相沉淀法制备聚吡咯-碳纳米管-铁化合物复合材料(Fe-PPy-CNTs),通过对复合材料Fe-PPy-CNTs热处理,成功制备出铁基氮掺杂碳纳米管催化剂Fe NCNTs.X射线衍射分析表明,热处理使Fe-PPy-CNTs复合物中Fe3O4向Fe3N和Fe转化,700°C热处理制备的Fe NCNT700中铁主要是Fe3O4相,但也有Fe相.800和900°C热处理制备的催化剂Fe NCNT800和Fe NCNT900则明显有Fe3N和Fe形成.随着热处理温度升高,Fe NCNTs催化剂氮含量降低,其含氮官能团也由吡咯型氮向吡啶型和石墨型氮转化.电化学分析表明,含有Fe3N的Fe NCNT800和Fe NCNT900催化剂具有明显的氧还原催化活性,其中,Fe NCNT800因其具有高的比表面积、高的氮含量和高比例的有利于增强氧吸附能力和弱化O―O键的石墨氮官能团,而表现出优于Fe NCNT900氧还原催化活性及稳定性.     

Effects of Zn promoter on the structure and Fischer-Tropsch performance of iron catalyst

采用低温N2吸附、XRD、MES、CO-TPR和H2-DTG研究了Zn(100 gFe/x gZn,x=7～100)助剂对Fischer-Tropsch(F-T)合成Fe基催化剂的织构性质、还原行为以及相变结构的影响；在H2/CO=2.0、260℃、1.5 MPa和4000 mL/(g·h)条件下在固定床反应器上考察了Zn助剂含量对Fe基催化剂F-T合成反应活性、烃产物选择性和运行稳定性的影响.研究结果表明,随着Zn含量的增加,氧化态催化剂的物相由α-Fe2O3和ZnFe2O4逐渐向ZnFe2O4和ZnO转变,ZnFe2O4在催化剂中优先生成,只有在超出其计量比1∶2之后才有ZnO出现.由于ZnFe2O4较为稳定,能够促进催化剂中Fe物相的分散,导致比表面积增加.在还原和反应态催化剂中,ZnFe2O4一方面抑制催化剂的过度还原和碳化；另一方面表现为稳定活性相铁碳化物.催化剂的F-T反应性能评价结果表明,纯铁催化剂由于铁碳化物氧化而迅速失活,而Zn助剂催化剂却由于ZnFe2O4的稳定作用,活性较为稳定.同时,由于催化剂在反应初相变的影响,导致Zn助剂催化剂的初始烯烃选择性随着Zn含量的增加而增加,在相态稳定之后选择性趋于一致.     

A carbanion induced synthesis of highly congested pyrazole and imidazole containing heterocycles

An efficient approach to the synthesis of highly congested di, penta and hexacyclic pyrazoles as well as imidazole fragment containing novel heterocyclic molecule has been developed through a carbanion induced transformation of suitably functionalized 2H-pyran-2-ones, benzo[h]chromene and thiochromeno[4,3-b]pyrans. Due to the presence of fluorescence, we report their prime application metal sensor as off/on switching in ferric ions.     

Selective synthesis of 4,5-dihydroimidazo- and imidazo[1,5-a]quinoxalines via modified Pictet–Spengler reaction

An efficient tandem approach for the selective synthesis of 4,5-dihydroimidazo[1,5-a]quinoxalines 6a–g and imidazo[1,5-a]quinoxalines 7a–h by the reaction of 2-imidazolyl anilines 4a–c with aryl aldehydes 5a–k under mild reaction conditions is described. Introduction of electron releasing alkyl groups in substrates 4a–b was found to be instrumental for the success of the reaction.     

Understanding the Diels-Alder reactivity of 1,2-azaborine analogues

The Diels-Alder reactivity of 1,2-heteroborines (H₄C₄B(H)X, X?=?NH, PH, AsH; O, S, Se) has been computationally explored by means of Density Functional Theory (DFT) calculations. The influence of the HB?=?X fragment on the reactivity of the system has been quantitatively analyzed in detail by means of the so-called Activation Strain Model (ASM) of reactivity. It is found that the interaction between these species and the dienophile is significantly stronger than that computed for their all-carbon isoelectronic counterpart, benzene. In addition, the strain energy plays a key role in the observed reactivity trends. The role of the aromaticity strength of these heteroarenes on the reactivity is also assessed.     

Synthesis of N-substituted carbazolones from α-iodo enaminones via Pd(0)-catalyzed intramolecular coupling under microwave irradiation

A variety of N-aryl and N-alkyl carbazolones were conveniently achieved in good to high yields via Pd₂(dba)₃-mediated intramolecular coupling of N-substituted α-iodo enaminones under microwave irradiation. The Pd(0)-catalyzed cyclization was found to proceed favorably with the more electron-deficient phenyl ring during the reactions involving unsymmetrical N,N-diaryl α-iodo enaminones. This unique property enables the construction of carbazolone skeleton containing nitro substituted benzenoid ring.     

Synthesis of substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles by intramolecular nitrilimine cycloaddition

Both substituted 2,4,5,6-tetrahydrocyclopenta[c]pyrazoles and 2,4,5,6-tetrahydropyrrolo[3,4-c]pyrazoles have been synthesized by the 3+2 intramolecular dipolar cycloaddition of nitrilimines to alkynes. This cyclization has been extended to more versatile 3-bromo derivatives by the use of alkynylbromides as dipolarophiles.     

Catalyst free,visible-light promoted photoaddition reactions between C60 and N-trimethylsilylmethyl-substituted tertiary amines for synthesis of aminomethyl-1,2-dihydrofullerenes

An efficient and benign method for the preparation of aminomethyl-substituted fullerenes has been developed. The process, involving catalyst free, visible-light irradiation of 10% EtOH-toluene solutions containing fullerene C₆₀ and N-trimethylsilylmethyl-substituted amines by using a 20 W compact fluorescent lamp, leads to formation of aminomethyl-substituted fullerene adducts in a highly efficient manner. The photoaddition reaction takes place via a pathway initiated by visible light absorption by C₆₀, followed by SET from the amine to the triplet excited state of C₆₀. Ethanol-promoted desilylation of the resulting a minimum radical then generates the corresponding α-amino radical which couples with the C₆₀ radical anion to form the anion precursor of the fullerene adducts. The new approach using visible-light takes place under mild conditions and it does not require the use of photocatalysts. Thus, the method developed in this effort could broadens the range of functionalized fullerene derivatives that can be readily prepared.     

Highly efficient and stereoselective cycloaddition of nitrones to indolyl- and pyrrolylacrylates

The reactions of various nitrones with indolyl- and pyrrolylacrylates proceeds regioselectively with high diastereoselectivity in the case of aldonitrones, and represents an effective method for obtaining new indolyl- and pyrrolyl-substituted isoxazolidine carboxylates stabilized by weak (CH?O) and moderate (NH?N) strength intramolecular hydrogen bonding. The resulting cycloadducts exhibit promising in vitro anti-influenza activities.     

Transition metal-free direct amination of benzoxazoles using formamides as nitrogen sources

A transition metal-free method for the direct amination of benzoxazoles using formamides as nitrogen sources is reported, which was mediated by an inexpensive and environmentally friendly tetrabutylammonium iodide/tert-butyl hydroperoxide system and gave the 2-aminobenzoxazole derivatives with moderate to good yields.     

l-Proline-catalyzed five-component domino reaction leading to multifunctionalized 1,2,3,4-tetrahydropyridines

Multifunctionalized 1,2,3,4-tetrahydropyridines are concisely synthesized in good yields via l-proline-catalyzed or l-proline/FeCl₃-cocatalyzed one-pot multicomponent reactions (MCRs). The MCRs involve a domino hydroamination/prins reaction/Mannich-type reaction/intramolecular dehydration-cyclization process. The molecular structure of 5baa, one of multifunctionalized 1,2,3,4-tetrahydropyridines, was confirmed by single-crystal X-ray diffraction.     

Exploring the scope of the Gewald reaction: Expansion to a four-component process

An efficient four-component reaction was developed to take advantage of the reactivity of the 2-aminothiophene-3-carbonitrile functionality, which is obtained during the classical three-component Gewald reaction. Various α-methylene bearing ketones were reacted with malononitrile, elemental sulfur, and aryl/heteroarylnitrile derivatives in t-BuOH/NaOH to afford 2-arylthieno[2,3-d]pyrimidin-4-amines in high yields. Preliminary studies revealed the photophysical properties of the products and their potential for use as metal sensors.