ZrO4/SiO2-Al2O3催化肉桂醛MPV转移加氢性能

以九水合硝酸铝（Al（NO₃）₃·9H₂O）与正硅酸乙酯（TEOS）为前驱盐,采用溶胶-凝胶法制备一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,并通过浸渍硝酸氧锆引入ZrO₂,制备ZrO₂/SiO₂-Al₂O₃复合氧化物催化剂,考察催化剂在肉桂醛（CAL）MPV转移加氢中的催化性能,并结合N₂物理吸附、X射线粉末衍射（XRD）、傅里叶变换红外光谱（FTIR）、NH₃-程度升温脱附（NH₃-TPD）、Py-原位红外（Py-IR）等技术,研究催化剂结构、织构以及表面性质与其催化性能间的构效关系.研究表明,所制备的催化剂均以L酸为主,并含有少量B酸中心,这使得加氢产物以肉桂醇（COL）为主,并含有少量1-苯丙烯-2-丙基醚（CPE）.Al₂O₃含量不仅影响催化剂表面的酸中心数量,而且对催化剂的织构参数有较大影响.随Al₂O₃含量的增加,催化剂表面L酸与B酸中心均有所增加,而孔径则持续变小,这使得催化反应呈现CAL转化率先增加后减少、目标产物COL选择性先稍有减小后有所增加的趋势.在Si/Al比为2时,催化剂具有最优的催化性能,优化反应条件下,CAL转化率达96%,目标产物COL选择性达90%.     

Ni/SiO2-Al2O3催化乙酰丙酸加氢制γ-戊内酯

采用溶胶-凝胶法制备了一系列不同Al₂O₃含量的SiO₂-Al₂O₃复合氧化物,以该系列复合氧化物为载体,采用等体积浸渍法制备了Ni负载量15%（重量百分比）的催化剂,用于催化乙酰丙酸加氢制γ-戊内酯.采用N₂物理吸附、X射线衍射（XRD）、H₂程序升温还原（H₂-TPR）、H₂程序升温脱附（H₂-TPD）、NH₃程序升温脱附（NH₃-TPD）和吡啶吸附红外（Py-IR）等手段对催化剂进行了表征.结果表明,不同载体催化剂的活性组分分散度及表面酸性质存在明显差异,显著影响了催化剂吸附、活化H₂与C=O键的能力,进而影响了催化剂的乙酰丙酸加氢活性.其中,Ni/SiO₂-Al₂O₃催化剂上的L酸中心能够促进C=O键的吸附、活化,与金属Ni上的H₂吸附活性位协同作用,大大提高了乙酰丙酸加氢活性.因此,具有最多L酸中心和丰富H₂吸附活性位的Ni/SiO₂-8Al₂O₃催化剂表现出最高的乙酰丙酸加氢活性,在180℃、4 MPa氢气压力下,乙酰丙酸转化率达到90.5%,目标产物γ-戊内酯选择性为100%.     

焙烧温度对Mn/Al2O3-TiO2催化剂结构及氧化NO性能的影响

采用溶胶凝胶法和浸渍法制备10% Mn/Al₂O₃-TiO₂催化剂,借助TPO、XRD、O₂-TPD、Raman、XPS等手段,考察焙烧温度(450~650 ℃)对催化剂结构以及氧化NO性能的影响。TPO结果表明催化剂活性随焙烧温度的升高先增后减,其中焙烧温度为550 ℃时催化剂活性最好。XPS结果显示随着焙烧温度的升高(450~550 ℃),催化剂表面Mn³⁺的含量逐渐升高,与催化剂活性的强弱成对应关系,并且催化剂晶格氧含量下降,而表面化学吸附氧从40.9%增加到64.8%。Raman分析显示550 ℃焙烧时,催化剂表面存在丰富的Mn₂O₃活性物种,并且O₂-TPD分析也表明随着焙烧温度的升高,晶格氧向表面化学吸附氧流动,提高了化学吸附态氧物种的含量。这些结果表明Mn₂O₃可能是NO氧化起主要作用的活性Mn物种,释放更多的表面化学吸附氧物种,将有助于促进NO的催化氧化。     

TiO2微粒功能化多孔Al2O3膜的光电化学研究

用恒电位法制备了多孔Al₂O₃薄膜, 通过在Al₂O₃薄膜孔内水蒸汽水解钛酸异丙酯生成了锐钛矿型TiO₂微粒, 制备出了Al₂O₃与TiO₂微粒的复合薄膜. 用XRD, SEM, 光电化学方法进行了研究. 实验表明: 该复合薄膜具有光电转换特性, 在光催化、光电化学太阳能转换中具有应用价值.     

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H₂-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

Fe2O3/Al2O3二元气凝胶合成高质量单壁纳米碳管

通过溶胶和超临界干燥方法制得了Fe₂O₃/Al₂O₃二元气凝胶，其比表面积和孔隙体积分别为246 m²·g^-1和1.89 cm³·g^-1，并具有较宽的孔径分布。以Fe₂O₃/Al₂O₃二元气凝胶作催化剂，通过甲烷催化裂解成功地合成了高质量的单壁纳米碳管。利用FESEM、TEM和HRTEM、Raman光谱等分析手段研究了反应温度对单壁纳米碳管生长的影响。结果表明在900 ℃时合成单壁纳米碳管的质量较高，并且合成的炭产物为毡状，该炭产物主要为高质量的单壁纳米碳管。     

H2SO4处理的Nb2O5/γ -Al2O3催化剂表面酸性与催化性能研究

用Hammett指示剂法、红外光谱（IR）、示差扫描量热-热重法（DSC-TG）和微型催化反应装置等研究了H₂SO₄处理的负载型Nb₂O₅/γ-Al₂O₃催化剂表面酸性和催化异丁烯（IB）与异丁醛（IBA）反应生成2，5-二甲基-2，4-己二烯（DMHD）的催化性能。结果表明随所用H₂SO₄浓度增加，Nb₂O₅/γ-Al₂O₃催化剂表面酸性增强，B酸量增加，L酸量先增加后下降。经H₂SO₄处理的Nb₂O₅/γ-Al₂O₃催化剂的催化活性明显增加，但当H₂SO₄浓度超过0.05 mol·L^-1时催化活性又急剧下降，这可能是因为在H₂SO₄处理的催化剂表面形成的强酸中心上，产物分子进一步转化为积炭且封闭催化剂活性表面，导致催化活性下降。     

Au/Al2O3纳米复合薄膜的制备和表征

用溶胶-凝胶法制备了Au/Al₂O₃纳米复合薄膜。利用X-射线衍射、X-射线光电子能谱、原子力显微镜以及紫外-可见光谱对薄膜的微观结构、表面形貌及光学性能进行了表征,研究表明:Au/Al₂O₃纳米复合薄膜是由纳米微晶组成的颗粒膜, 复合薄膜均匀、致密、无裂纹,Au以纳米晶核形式镶嵌于Al₂O₃基体中,纳米Au晶核的粒径为23～26nm;复合薄膜在可见光区有较强的吸收,吸收峰位置与烧结温度有关,吸收强度随烧结温度和金添加量增大而增大。     

Pt/ZrO2-Al2O3催化剂催化氧化C3H6和CO性能

采用共沉淀法合成了ZrO₂与Al₂O₃的不同质量比的ZrO₂-Al₂O₃复合氧化物,并以此为载体通过等体积浸渍法制备了1.5% Pt/ZrO₂-Al₂O₃（w/w）催化剂。以C₃H₆和CO为反应物的催化性能评价显示,在系列催化剂中以Pt/Zr（0.4）-Al₂O₃催化剂催化氧化活性最为优异,其C₃H₆和CO的起燃温度（T₅₀）小于125℃,完全转化温度（T₉₀）小于150℃。采用XRD、低温N₂吸附、H2-TPR、CO脉冲吸附等分析表征技术探索了催化剂物相结构、比表面积、颗粒尺寸等对催化活性的影响规律。结果发现,ZrO₂-Al₂O₃复合氧化物具有Al₂O₃材料的介孔织构和大比表面积特性,且产生了Al_xZr_1-xO_y固溶体新物相。适当的ZrO₂与Al₂O₃的质量比,是改善Pt与ZrO₂-Al₂O₃的相互作用强度,促进贵金属Pt的分散,提升Pt/ZrO₂-Al₂O₃催化剂的低温氧化活性的关键。     

应用原位漫反射红外-质谱技术研究CuO/Al2O3催化剂表面酸性及其反应性能

应用原位漫反射红外-质谱联用、程序升温和暂态响应技术研究了CuO/Al₂O₃催化剂表面酸性及其反应性能. 实验结果表明, CuO/Al₂O₃催化剂表面呈Lewis酸性, 硫化不仅可增强CuO/Al₂O₃催化剂的Lewis酸性, 而且可产生新的Brønsted酸性位; 吸附于Lewis酸性位的NH₃具有选择性催化还原(SCR)活性. 而在硫化样Cu8(400S)中Lewis和Brønsted酸性位同时存在的情况下, 吸附于Lewis和Brønsted酸性位的氨均具有SCR活性, 且后者较前者弱; CuO/Al₂O₃催化剂上的SCR反应遵循Eley-Rideal机理, 即SCR反应发生于吸附态NH₃与气相NO之间.     

Photodegradation of 2,4-D over PdO/Al2O3-Nd2O3 photocatalysts prepared by the sol-gel method

The photocatalytic activity of 1.0 wt% PdO supported on Al₂O₃-Nd₂O₃ binary oxides prepared by the sol-gel method was studied in the photodegradation of 2,4-dichlorophenoxyacetic acid (2,4-D). The photocatalysts were characterized by N₂ physisorption, XRD and UV-vis spectroscopy. PdO supported on γ-Al₂O₃ photo-degrades the 2,4-D, however the addition of Nd₂O₃ to γ-Al₂O₃ notably improves the photocatalytic activity. As the concentration of Nd₂O₃ in the binary oxide increases from 2 to 10 wt%, the photodegradation of 2,4-D is highly enhanced. The catalytic test for PdO supported on pure Nd₂O₃ showed scarce photocatalytic activity. Total organic carbon (TOC) analysis showed that the 2,4-D has been completely destroyed on the PdO/Al₂O₃-Nd₂O₃ photocatalysts after 6 h under irradiation.     

The formation and physicochemical characterization of Al2O3-doped manganese ferrites

Mn/Fe mixed oxide solids doped with Al₂O₃ (0.32-1.27 wt.%) were prepared by impregnation of manganese nitrate with finely powdered ferric oxide, then treated with different amounts of aluminum nitrate. The obtained samples were calcined in air at 700-1000 °C for 6 h. The specific surface area (S_BET) and the catalytic activity of pure and doped precalcined at 700-1000 °C have been measured by using N₂ adsorption isotherms and CO oxidation by O₂. The structure and the phase changes were characterized by DTA and XRD techniques. The obtained results revealed that Mn₂O₃ interacted readily with Fe₂O₃ to produce well-crystallized manganese ferrite (MnFe₂O₄) at temperatures of 800 °C and above. The degree of propagation of this reaction increased by Al₂O₃-doping and also by increasing the heating temperature. The treatment with 1.27 wt.% Al₂O₃ followed by heating at 1000 °C resulted in complete conversion of Mn/Fe oxides into the corresponding ferrite phase. The catalytic activity and S_BET of pure and doped solids were found to decrease, by increasing both the calcination temperature and the amount of Al₂O₃ added, due to the enhanced formation of MnFe₂O₄ phase which is less reactive than the free oxides (Mn₂O₃ and Fe₂O₃). The activation energy of formation (ΔE) of MnFe₂O₄ was determined for pure and doped solids. The promotion effect of aluminum in formation of MnFe₂O₄ was attributed to an effective increase in the mobility of reacting cations.     

系列硅铝比纳米薄层ZSM-5分子筛的合成和表征

以自制不对称双子季铵盐表面活性剂为模板, 在水热合成体系中控制合成系列硅铝比纳米薄层ZSM-5分子筛.采用X射线衍射(XRD)、N₂吸附-脱附、X射线荧光光谱(XRF)、扫描电镜(SEM)和²⁷Al魔角旋转核磁共振(²⁷Al MAS-NMR)对合成的样品进行了表征. 详细研究了晶化温度、晶化时间、结构导向剂(SDA)用量、碱度等对合成的影响和纳米薄层ZSM-5分子筛的形成过程. 结果表明: 分子筛硅铝比越高, 结构导向剂用量越大, 所需的晶化时间越短; 晶化温度越高, 晶化时间越短; 且不同硅铝比纳米薄层ZSM-5分子筛的形貌规整度、比表面积和介孔/微孔孔容比例随着硅铝比而变化.     

Ion-beam irradiation of lanthanum compounds in the systems La2O3-Al2O3 and La2O3-TiO2

Thin crystals of La₂O₃, LaAlO₃, La_2/3TiO₃, La₂TiO₅, and La₂Ti₂O₇ have been irradiated in situ using 1 MeV Kr²⁺ ions at the Intermediate Voltage Electron Microscope-Tandem User Facility (IVEM-Tandem), Argonne National Laboratory (ANL). We observed that La₂O₃ remained crystalline to a fluence greater than 3.1×10¹⁶ ions cm⁻² at a temperature of 50 K. The four binary oxide compounds in the two systems were observed through the crystalline-amorphous transition as a function of ion fluence and temperature. Results from the ion irradiations give critical temperatures for amorphisation (T_c) of 647 K for LaAlO₃, 840 K for La₂Ti₂O₇, 865 K for La_2/3TiO₃, and 1027 K for La₂TiO₅. The T_c values observed in this study, together with previous data for Al₂O₃ and TiO₂, are discussed with reference to the melting points for the La₂O₃-Al₂O₃ and La₂O₃-TiO₂ systems and the different local environments within the four crystal structures. Results suggest that there is an observable inverse correlation between T_c and melting temperature (T_m) in the two systems. More complex relationships exist between T_c and crystal structure, with the stoichiometric perovskite LaAlO₃ being the most resistant to amorphisation.     

Fischer-Tropsch synthesis over Ru/Al2O3 catalysts

Fischer-Tropsch syntheses (FTS) were carried out in a slurry phase over Ru/Al₂O₃ catalysts using hexadecane as a solvent. The outcome of the FTS was dependent on the oxide support, calcination temperature, synthesis gas composition and sulfur content. The addition of Mn/Na to Ru/Al₂O₃ was effective in raising the initial activity and C5+ selectivity, but after 20 hours, the performance of the modified catalyst was similar to that of the unmodified catalyst. An additional investigation involving the use of fresh vs used catalysts demonstrated that an agglomeration of the metallic Ru, at least in part, does occur during the reaction.     

Al含量对Pt-SO2-4 /ZrO2-Al2O3固体超强酸催化

通过向SO^2-₄ /ZrO₂催化剂中同时引入适量的Pt和Al₂O₃, 制备出了具有较高催化性能和稳定性的Pt-SO^2-₄ /ZrO₂-Al₂O₃型固体超强酸催化剂. 以正戊烷异构化反应为探针, 考察了Al含量对催化剂性能的影响; 并采用X射线衍射(XRD)、比表面积测定(BET)、红外(IR)光谱、程序升温还原(TPR)、热重-差热分析(TG-DTA)和氨-程序升温脱附(NH₃-TPD)手段对催化剂进行了表征. 结果表明, Al能够提高ZrO₂的晶化温度, 抑制硫的分解, 增加催化剂的比表面积, 增强硫氧键的结合, 提高催化剂的还原性能, 增加催化剂的酸强度和酸总量. 当Al₂O₃含量(质量分数, w)为5.0%时, Pt-SO^2-₄ /ZrO₂-Al₂O₃固体超强酸催化剂的催化活性最好, 在100 h内异戊烷收率可稳定在52.0%以上, 选择性在98.2%以上.     

Structural models for intergrowth structures in the phase system Al2O3-TiO2

The phase system Al₂O₃-TiO₂ was investigated in the compositional range from 48:52 to 62:38 mol% Al₂O₃:TiO₂. The samples were prepared by melting the binary oxides in an arc-imaging furnace and the obtained samples were examined by powder X-ray diffraction. The recorded powder patterns could be interpreted in terms of intergrowth structures consisting of two basic building blocks, which were deduced from the known crystal structures of β-Al₂TiO₅ and Al₆Ti₂O₁₃. The structure of a new ordered compound with the formula Al₁₆Ti₅O₃₄ is proposed. The thermal stability was estimated from DTA and tempering experiments and showed that all prepared samples decompose at temperatures around 800 °C into the binary oxides corundum and titania.