石墨烯/铁氰化钴复合膜修饰玻碳电极同时测定对苯二酚、邻苯二酚和间苯二酚

采用滴涂法和电沉积法制备了石墨烯/铁氰化钴复合膜修饰玻碳电极. 用扫描电镜对该纳米复合膜进行了表征.用循环伏安法研究了对苯二酚(HQ)、邻苯二酚(CT)和间苯二酚(RS)在修饰电极上的电化学行为. 实验结果表明, 相对于裸玻碳电极和石墨烯修饰电极, HQ, CT 和RS 在石墨烯/铁氰化钴修饰电极上的氧化峰电流显著提高. 利用差分脉冲伏安法测定, HQ, CT 和RS 分别在1.0×10^－6～1.5×10^－4 mol/L, 1.0×10^－6～2.0×10^－4 mol/L 和3.5×10^－6～2.5×10^－4 mol/L浓度范围内与氧化峰电流呈良好的线性关系, 相关系数分别为0.991, 0.993 和0.992. 信噪比为3 时, HQ, CT 和RS 检出限分别为2.0×10^－7, 2.1×10^－7 和3.5×10^－7 mol/L. 将该方法用于水样分析, 回收率为95.6%～106.1%.     

分子印迹固相萃取-液相色谱质谱联用对4种磺酰脲类除草剂残留的测定

采用苄嘧磺隆分子印迹固相萃取柱(MISPE)对加标大米中的苄嘧磺隆、甲磺隆、苯磺隆和烟嘧磺隆4种磺酰脲类除草剂进行净化和富集预处理,并采用LC-MS方法进行定量分析.质谱条件为:正离子检测模式(M+H),检测质量范围为m/z 200 ～800 ,毛细管电压3.93 kV,锥孔电压20 V,脱溶剂温度250 ℃,辅助气流速4 L/min.4种磺酰脲类除草剂在0.01 ～0.70 mg·L~(-1)范围内线性良好.回收率为68% ～100%,表明样品液中的烟嘧磺隆、甲磺隆、苯磺隆和苄嘧磺隆能直接被分子印迹固相萃取柱中的印迹位点保留,而杂质几乎不被保留.分子印迹固相萃取柱对磺酰脲类除草剂表现出良好的识别性能.     

固相膜萃取/高效液相色谱法测定环境水体中的磺酰脲类除草剂

建立了一种基于C₁₈固相萃取膜预富集、高效液相色谱法定量分析环境水体中6种痕量磺酰脲类除草剂的快速分析方法。优化了色谱分离条件,考察了洗脱剂种类与体积、水样pH值和盐效应等条件对萃取效率的影响。在优化条件下,6种磺酰脲类除草剂的峰面积与其质量浓度呈良好的线性关系,苯磺隆的线性范围为0.10²0.0μg/L,其余均为0.05²0μg/L,相关系数为0.999 0⁰.999 5,方法检出限为0.019⁰.037μg/L。对地表水和海水的加标回收率分别为92.6%¹05.7%和89.8%¹08.7%,相对标准偏差分别为0.7%⁷.1%和0.5%⁴.0%。该方法操作简单、快速、准确、灵敏度高。     

谷胱甘肽磁性分子印迹聚合物的制备及吸附性能研究

采用表面分子印迹技术,以谷胱甘肽（GSH）为模板分子,N-乙烯基吡咯烷酮（NVP）和丙烯酰胺（AM）为功能单体,N,N’-亚甲基双丙烯酰胺（MBA）为交联剂,γ-（甲基丙烯酰氧）丙基三甲氧基硅烷（KH570）改性的Fe₃O₄纳米颗粒为磁性载体,制备了对GSH有特异识别性的磁性分子印迹聚合物（GSH-MMIPs）. 利用X射线衍射仪（XRD）、透射电子显微镜（TEM）、红外光谱（FT-IR）和振动样品磁强计（VSM）对聚合物进行了表征,结果表明磁性载体表面成功地包覆了分子印迹聚合物薄层. 静态吸附平衡实验和Scatchard分析结果表明,GSH-MMIPs中存在两类不同的结合位点,平衡解离常数分别为8.786×10^-4 mol/L和5.424×10^-3 mol/L,最大吸附量分别为49.195 mg/g和155.003 mg/g. 与化学组成相同的磁性非印迹聚合物（GSH-MNIPs）相比,GSH-MMIPs对谷胱甘肽有较高的选择吸附性能.     

分子印迹固相萃取-高效液相色谱法同时检测烟叶中磺酰脲类农药残留

以氯磺隆（CS）为模板分子,甲基丙烯酸为功能单体,三羟甲基丙烷三甲基丙烯酸酯为交联剂,在二氯甲烷氛围中,经沉淀聚合制备氯磺隆分子印迹聚合物（CS-MIP）微球。将该聚合物微球作为填料制得分子印迹固相萃取柱用于样品前处理,建立了分子印迹固相萃取-高效液相色谱（MIP-SPE-HPLC）同时检测烟叶中6种磺酰脲类除草剂残留的分析方法。针对氯磺隆、甲磺隆、苄嘧磺隆、苯磺隆、胺苯磺隆和烟嘧磺隆6种磺酰脲类除草剂,在烟叶中加标0.50~50 μg/g,经氯磺隆分子印迹固相萃取柱（CS-MIP-SPE）净化和富集,高效液相色谱（HPLC）检测,其平均回收率为77.60%~102.05%,相对标准偏差为0.16%~7.07%,检出限为0.08~0.46 μg/g。将MIP-SPE-HPLC方法用于实际农药残留检测,结果表明可同时满足烟叶中多种磺酰脲类除草剂残留量的检测要求。     

磁性普鲁士蓝纳米颗粒的合成及其化学修饰电极的制作

利用FeSO₄与FeCl₃合成了超细磁性Fe₃O₄纳米颗粒, 并进一步利用该纳米颗粒与铁氰酸钾在酸性溶液(pH～2)中的化学反应成功制备了一种新型的磁性普鲁士蓝纳米颗粒; 研究了该磁性颗粒的磁学性能, 通过磁力将其修饰于固体石蜡碳糊电极表面制成了化学修饰电极, 考察了该电极对过氧化氢的电催化还原及对水合肼的电催化氧化特性. 该化学修饰电极可对过氧化氢和水合肼进行测定, 线性范围分别为过氧化氢2×10^－6～5×10^－3 mol/L, 水合肼7.2×10^－7～3.6×10^－4 mol/L. 利用磁性普鲁士蓝纳米颗粒制得的修饰电极具有催化性能高、稳定性好、表面易更新等优点.     

以马来松香丙烯酸乙二醇酯为交联剂的茶碱分子印迹膜电化学传感器的研究

利用分子印迹技术, 以马来松香丙烯酸乙二醇酯为交联剂, 丙烯酸为功能单体研制了测定茶碱的新型电化学传感器. 以自由基热聚合的方式于玻碳电极表面制备茶碱分子印迹聚合物膜. 通过循环伏安法、电化学交流阻抗法及计时电流法研究了传感器对茶碱的响应特性. 结果表明, 在最佳的实验条件下, 传感器的峰电流与茶碱浓度在2.00×10^-7～3.45×10^-4 mol/L 范围内呈现出良好的线性关系(线性相关系数为0.9961), 检出限(S/N＝3)为1.00×10^-7 mol/L;该传感器的选择性高, 稳定性和重现性好, 将此传感器用于茶碱缓释片中茶碱的含量测定, 回收率为95.6%～103.8%.关键词 马来松香丙烯酸乙二醇酯; 茶碱; 分子印迹聚合物; 电化学传感器     

分子印迹电化学传感器选择性识别及电催化检测多巴胺

以多巴胺为模板分子、溴酚蓝为单体, 在玻碳电极表面制得分子印迹膜. 洗脱后重新吸附多巴胺分子, 同时利用聚溴酚蓝膜对多巴胺氧化的电催化作用, 对多巴胺进行定量分析. 多巴胺在0～1.2×10^-6 mol/L浓度范围内与电流变化值有线性关系. 由于印迹膜的催化作用, 检出限达1.62×10^-10 mol/L. 该传感器可用于选择性测定多巴胺, 抗坏血酸和尿酸等共存物不干扰测定. 利用该传感器直接测定了血清中多巴胺含量, 回收率在95.2%～103.0%之间.     

氮掺杂碳纳米管修饰电极的电化学行为

制备了氮掺杂改性的碳纳米管, 并用循环伏安法(CV)测定了多巴胺(DA)和抗坏血酸(AA)在不同氮含量的碳纳米管修饰电极上的电化学行为. 结果表明, 氮掺杂碳纳米管修饰电极对AA和DA有不同的电催化行为, 其中高氮含量修饰电极对AA的催化作用强, 而低氮含量修饰电极对DA的催化作用强. 微分脉冲伏安法(DPV)的结果显示, DA的氧化峰电流与其浓度在5.0×10^－6～2.0×10^－4 mol/L范围内呈良好的线性关系, 检出限达1.64×10^－6 mol/L (S/N＝3); AA氧化峰电流与其浓度在3.0×10^－5～1.0×10^－2 mol/L范围内呈良好的线性关系, 检出限达3.26×10^－6 mol/L (S/N＝3). 该修饰电极在AA大量存在(AA浓度为DA浓度两万倍)时可选择性地实现多巴胺的测定而不造成干扰.     

基于对氨基苯甲酸/硫堇/纳米金共价修饰玻碳电极的葡萄糖生物传感器

实验制备了以对氨基苯甲酸(4-ABA)、硫堇(TH)、纳米金(Au NPs)共价键合葡萄糖氧化酶的新型葡萄糖生物传感器. 主要采用循环伏安法, 以羟基二茂铁作为电子媒介体, 对含葡萄糖和未含葡萄糖的电解液进行了研究. 结果表明: 传感器的响应电流值随葡萄糖氧化酶膜层数的不同而变化. 考虑到酶电极的长期稳定性与构造简单性, 我们制作了两层葡萄糖氧化酶膜的酶电极. 该传感器对1×10^－2 mol/L葡萄糖的响应电流达2.47 μA, 响应时间仅4.7 s. 该生物传感器检测的线性范围为3×10^－5～1×10^－3 mol/L, 最低检测浓度可达5.8×10^－6 mol/L. 该传感器制备简单, 稳定好, 具有一定的使用价值.     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.