泡沫镍及负载型镍催化剂制备纳米碳纤维层的研究

纳米碳纤维可用在催化材料、储氢材料、及纳米电子器件等方面。本文对用泡沫镍及负载型镍催化剂催化分解乙烯或丙烯制备纳米碳纤维进行了研究。利用X射线衍射仪、物理吸附仪、扫描电镜进行了分析表征,并考察了催化剂、碳源、生长温度对纳米碳纤维生长量、形貌、结构的影响。结果表明:在生长温度450℃,乙烯流率30mL/m in的条件下,负载型镍催化剂纳米碳纤维的生长量要高出泡沫镍3~6倍,负载型镍催化剂制备的纳米碳纤维直径为40~60纳米,小于泡沫镍的情况。泡沫镍催化分解乙烯制备纳米碳纤维时,纳米碳纤维的生长量和平均直径随温度的降低而逐渐减小。纳米碳纤维在泡沫镍上的最低生长温度为420℃,在低于480℃生长纳米碳纤维时泡沫镍的骨架结构不会被破坏,由此制备的纳米碳纤维在新型结构催化材料中有很好的的应用前景。     

三维结构泡沫Co3O4的制备及电化学性能

通过电化学沉积方法在三维结构泡沫镍基体上沉积金属钴层, 利用固相氧化方法制备了三维结构泡沫Co3O4负极. XRD和SEM结果显示, 电化学沉积制备得到具有纳米结构的金属钴层, 经固相氧化处理, 在泡沫镍基体表面形成了Co3O4微米级的致密活性氧化层. 通过充放电和循环伏安以及电化学阻抗等方法研究了电极的电化学性能, 结果表明, 当放电电位区间为0.05~3.2 V时, 三维泡沫Co3O4于0.2 C倍率下充放电, 初始容量损失为29%, 经50次循环后, 质量比容量为824 mA·h/g, 三维泡沫结构提高了Co3O4电极的循环容量保持性能和倍率性能.     

碳凝胶/泡沫镍一体化电极用于高性能的超级电容器

以氧化石墨、间苯二酚、甲醛和泡沫镍为原料,经85 oC水热碳化处理,在泡沫镍表面原位聚合形成了碳凝胶/泡沫镍一体化电极,冷冻干燥处理后可得多孔碳凝胶/泡沫镍一体化电极. 水系和有机系的超级电容器测试表明,多孔碳凝胶/泡沫镍一体化电极具有较高的比容量和良好的循环稳定性,其独特的一体化电极组成和多孔结构有利于电子和电解液离子的有效传输.     

CdSe/泡沫镍薄膜电极对结晶紫的光电催化降解

采用恒电位电沉积法,以泡沫镍为基底电极,制备了CdSe/泡沫镍薄膜电极,采用扫描电子显微镜、紫外可见漫反射光谱和能谱分析表征了CdSe薄膜的形貌及其组成。应用该电极研究结晶紫溶液在光电催化降解过程中的COD去除率。结果表明,以白炽灯(100 W,2只)为光源,采用电沉积30 min所得的CdSe/泡沫镍薄膜电极为工作电极,外加偏压为0.4 V(vs.SCE),0.01 mol/L NaCl为电解质,光电催化降解浓度为0.001 g/L的结晶紫溶液120 min,COD去除率达到84.3%。     

新型锂离子电池三维结构泡沫NiO电极的制备及电化学性能

通过固相氧化方法,以三维结构泡沫镍为基体和金属镍源,制备了三维结构泡沫氧化镍负极。XRD和SEM结果表明,经500℃氧化处理,泡沫镍基体上形成了NiO微米级的致密活性氧化层。通过充放电测试和循环伏安测试研究了电极的电化学性能,结果表明,三维结构泡沫氧化镍在放电电位区间0.05～3.2VvsLi/Li+,0.2C倍率下充放电,初始容量损失为20%,且经40次循环后,质量比容量为950mAh·g-1,三维泡沫氧化镍电极具有优异的循环容量保持性能。三维泡沫氧化镍具有的大的活性表面积,降低了界面反应的极化,从而提高了NiO电极的倍率放电性能。     

碱性Al-H_2O_2半燃料电池Au/Ni阴极性能研究

以泡沫镍为基体,AuCl3为沉积液,应用快速自沉积法制备了泡沫镍负载的纳米Au/Ni电极.电化学方法测定AuCl3溶液的浓度和沉积时间对Au粒子的尺寸和分布以及以该电极作为Al-H2O2半燃料电池阴极对H2O2性能的影响.实验表明,泡沫镍经2mmol·L-1AuCl3溶液浸渍60s后,其表面完全被粒径小于100nm的Au粒子覆盖;以其为阴极的Al-H2O2半燃料电池,在0.4mol·L-1H2O2溶液中峰值功率达135mW·cm-2.     

微波加热制备泡沫镍负载La3+掺杂纳米TiO2及其光催化降解甲醛的性能

 采用常规加热和微波加热方法制备了两种泡沫镍负载La3+掺杂的纳米TiO2光催化剂,以甲醛光催化降解为模型反应,考察了制备方法和掺杂La3+对催化剂催化性能的影响,并采用扫描电镜、透射电镜、 X射线衍射和能量分散式光谱分析对催化剂进行了表征. 结果表明,微波加热法制备的纳米TiO2具有典型的锐钛矿型晶体结构,其粒径均匀且明显小于常规加热法制备的催化剂. 泡沫镍负载1.5%La3+掺杂的TiO2的光催化性能得到明显改善,反应90 min后甲醛的降解率仍达到93%. 在实验中发现催化剂有失活现象,但经简单清洗后其活性能够恢复.     

以泡沫镍载NiCo2O4纳米线阵列为阴极催化剂的Al-H2O2半燃料电池

研究了以泡沫镍载NiCo2O4纳米线阵列为阴极催化剂的Al-H2O2半燃料电池的性能. 以无模板生长法制备了泡沫镍载NiCo2O4纳米线阵列阴极材料, SEM测定结果表明, NiCo2O4纳米线几乎垂直于泡沫镍载体表面生长. 以电压和功率密度-电流密度曲线研究了H2O2浓度、电解液流速和温度对电池性能的影响, 结果显示, 以铝片为阳极, 0.6 mol/L H2O2为氧化剂的电池的开路电压约为1.40 V; 在室温和57 ℃下, 电流密度为98和172 mA/cm2时, 最大功率密度分别达到79和120 mW/cm2.  在5000 s的测试时间内, 0.70 V的恒电流密度和75 mA/cm2 的恒电压值几乎为一常数, 这表明以泡沫镍载NiCo2O4纳米线阵列为催化剂电还原H2O2具有很好的活性、稳定性和传质性能.     

NiCo2O4纳米线对 H2O2电还原的催化性能

以无模板生长法制备了泡沫镍载NiCo2O4纳米线正极材料, XRD和SEM表征结果表明, 所得材料为NiCo2O4纳米线, 以循环伏安法和计时电流法研究了泡沫镍载NiCo2O4纳米线对H2O2电还原的催化性能. 结果显示, 在0.4 mol/L H2O2 和 3.0 mol/L NaOH 溶液中, 当电压为-0.4 V(vs. Ag/AgCl)时, 循环伏安的电流密度达到125 mA/cm2; 当电压为-0.2, -0.3和 -0.4 V 时, 在30 min 的测试时间内, 计时电流密度几乎均为一常数, 表明以泡沫镍载NiCo2O4纳米线为催化剂电还原H2O2具有很高的活性和很好的稳定性.     

泡沫镍载 NiCO2O4电极的制备及其催化 H2O2电氧化的性能

本文以水热法结合热处理法原位制备了泡沫镍载 NiCo₂O₄纳米线电极,使用XRD、SEM和TEM对合成的 NiCo₂O₄纳米线进行了表征,NiCo₂O₄纳米线直径约80 nm,长度约 3 ~ 5 μm. 使用循环伏安和计时电流法测试了泡沫镍载NiCo₂O₄纳米线催化H₂O₂的电氧化性能,结果表明泡沫镍载NiCo₂O₄纳米线对H₂O₂电氧化有着优良的催化活性、稳定性和传质性能,在0.3 V电位下0.4 mol·L ^-1 H₂O₂和2 mol·L ^-1 NaOH溶液中氧化电流可达380 mA·cm ^-2.     

Nickel-Zinc Battery with Nickel Oxide Electrode Made of Spherical Nickel Hydroxide on Foamed Nickel Support

Electrochemical and working characteristics of a nickel-zinc battery with nickel oxide electrode made of spherical nickel hydroxide on foamed nickel support were determined.     

Influence of Cobalt Intercalation on Processes in a Nickel-Zinc Battery with Nickel Oxide Electrode Fabricated from Spherical Nickel Hydroxide

The influence of cobalt on processes that occur in a nickel oxide electrode of a nickel-zinc battery, fabricated from spherical nickel hydroxide on foamed nickel support, was studied.     

含铌电容材料的制备及其性能

以草酸铌铵和葡萄糖为原料,经水热反应在泡沫镍基底上负载了含Nb的电容材料。通过红外光谱仪(FTIR)、扫描电子显微镜(SEM)、X射线衍射仪(XRD)等技术手段对制备的样品进行表征,比较不同条件下的含Nb电容材料的表面形貌,得出水热反应的最佳工艺条件,并对样品的电化学性能进行了研究。结果表明,制备含Nb电容材料的最佳工艺条件是葡萄糖和草酸铌铵的摩尔比为7:1,反应温度200 ℃,反应时间18 h,在此条件下,负载在泡沫镍上的含Nb氧化物的量为0.3707 g/cm²;当充放电电流密度为0.5 A/g时,含Nb电容材料的最大比电容能达到189.47 F/g,经过1000次循环后,其放电比电容的保持率仍保持在95%以上,是一种具有应用前景的超级电容器材料。     

Electrochemical hydrogen storage and usage aspects: Nickel electrode in acidic electrolyte

The conditions of electrochemical formation of nickel hydride are investigated. The electrochemical properties of different nickel-based materials (bulk, porous, foamed tapes) are examined to state the hydrogen adsorption/absorption phenomena and possibility to use them as a negative electrode in hydrogen devices (electrolyzers, rechargeable batteries, fuel cells). Surface activation of nickel materials are made by electroplating and etching methods. Thin palladium coating is used to prove the formation of nickel hydride during cathodic charging. Volt-amperometric and kinetic measurements show that not only palladium, but also activated nickel plays important role in the surface activation of electrode materials and promotion of hydrogen absorption in nickel substrate materials. Published in Russian in Elektrokhimiya, 2007, vol. 43, No. 5, pp. 624–629. Based on the paper delivered at the 8th Meeting “Fundamental Problems of Solid-State Ionics, Chernogolovka (Russia), 2006. The text was submitted by the authors in English.     

Ag@SiO2@NF电化学传感器的制备及其对铅离子的检测

本文采用溶胶-凝胶法制备巯基功能化的SiO₂微球,利用银与巯基的络合作用将银负载在SiO₂微球上,利用压片法将Ag@SiO₂修饰在泡沫镍表面,制备了Ag@SiO₂@NF电化学传感器,并研究了其在水中Pb²⁺检测方面的应用。通过透射电子显微镜,扫描电镜,电子能谱等对Ag@SiO₂@NF的形貌结构进行了表征,通过差分脉冲伏安法对Ag@SiO₂@NF的电化学性能进行了检测。结果表明,制备的Ag@SiO₂微球均匀的负载在泡沫镍表面。在最佳条件下使用差分脉冲伏安法对Pb²⁺进行电化学检测。测定的线性范围为1~5×10^-4M,检测限为0.761μmol·L^-1,为在各个环境中快速、准确、灵敏的检测水中Pb²⁺的含量提供了一种新思路。     

Coreflooding and Pore-Scale Visualization of Foamed Gel Flowed in Porous Network Media

To investigate the mechanisms of enhancing oil recovery and the flow behaviors of foamed gel in porous media, foamed gels with characteristics of excellent strength and viscosity were prepared with polymer, crosslinking agent, foam agent, and formation water. The breakthrough-vacuum method and a rotary viscometer were used to evaluate the strength and viscosity of foamed gel. Coreflooding and pore-level visualization experiments were performed in heterogeneous reservoir models. Laboratory results illustrate that high strength and viscosity of foamed gel can be prepared by 0.15% NJ-8, 0.2% polyacrylamide solution, and 1.5% foaming agent. The strength and viscosity of the foamed gel reached 0.06 MPa and 10,000 MPa · s, respectively. The results of coreflooding experiments in heterogeneous cores show that oil recovery can be improved by approximately 36.9% after injecting 0.3 pore volume of the foamed gel, and enhanced oil recovery is mainly attributed to the improving sweep efficiency of mid- to low-permeability layers. Images of visualization flooding demonstrate that foamed gel exhibits good oil resistance and elasticity when used with crude oil. Furthermore, the new amoeba effect, Jamin effect, fluid-diverting effect, and extruding effect between foamed gel and oil in porous media can enhance oil recovery by improving sweep efficiency.     

Heat-resistant foamed organoplastics based on a combination of polyimide felt, polyimide binders, and montmorillonite nanoparticles

A series of foamed organoplastics based on a combination of foamed fully aromatic polyimide binders and Arimid T polyimide felt were prepared. New composite foamed organoplastics reinforced with montmorillonite nanoparticles were prepared using commercially available aromatic monomers.     

微孔发泡聚合物基导电复合材料的研究进展

概述了用超临界流体作为物理发泡剂对聚合物基导电复合材料进行微孔发泡的基本原理,总结了聚合物基导电复合材料及其微发泡复合材料的几种导电机理,简要介绍了近年来微孔发泡聚合物基导电复合材料电学性能的研究现状。并从微发泡聚合物基导电复合材料的基体特性、所使用的导电填料类型、导电填料的含量、填料在基体中的分散方法及微发泡复合材料的泡孔形态等几个方面,分析了影响微孔发泡聚合物基导电复合材料电学性能的主要因素,并展望了新型微孔发泡聚合物基导电复合材料的研究和发展趋势。     

低含量聚乳酸对微孔发泡聚丁二酸丁二醇酯泡孔结构的改善

通过挤出制备了可生物降解聚丁二酸丁二醇酯(PBS)和3种聚乳酸(PLA)含量(7 wt%、15 wt%和20 wt%)的PBS/PLA共混物样品,采用超临界二氧化碳作为物理发泡剂对样品进行间歇发泡,研究发泡样品的泡孔结构,并分析其形成机理.在120oC发泡温度(Tf)下,借助PLA对PBS熔体黏弹性尤其是熔体强度的改善,获得了分布较均匀、形状较规则、直径较小(平均值约10μm)的微孔;共混物发泡样品的直径分布明显变窄,且符合高斯分布,这归因于细小的PLA相较均匀地分布于PBS基体中.进一步地,研究Tf对PBS和PLA含量为15 wt%的PBS/PLA共混物发泡样品泡孔结构的影响.结果表明,加入15 wt%的PLA使PBS的Tf下限从115oC降低至110oC,并显著改善了较高Tf(120和125oC)下制备的发泡样品内泡孔结构的均匀性.     

Synthesis of nanostructured carbon on Ni catalysts supported on mesoporous silica,preparation of carbon-containing adsorbents,and preparation and study of lipase-active biocatalysts

This work continues a series of our studies on the synthesis of nanostructured carbon (NSC) by the pyrolysis of H₂ + C₃–C₄ alkane mixtures on nickel and cobalt metal catalysts supported on chemically diverse inorganic materials (aluminosilicates, alumina, carbon) having different textural characteristics (mesoporous and macroporous supports) and shapes (granules, foamed materials, and honeycomb monoliths). Here, we consider Ni catalysts supported on granular mesoporous silica (SiO₂). It has been elucidated how the yield of synthesized carbon depends on the Ni/SiO₂ catalyst preparation method (homogeneous precipitation or impregnation) and on the composition of the impregnating solution, including the molar ratio of its components—nickel nitrate and urea. The morphology of catalytic NSC and Ni distribution in the silica granule have been investigated using a scanning electron microscope with an EDX analyzer. Carbon-containing composite supports (NSC/SiO₂) have been employed as adsorbents for immobilizing microbial lipase. The enzymatic activity and stability of the resulting biocatalysts have been estimated in transesterification reactions of vegetable (sunflower and linseed) oils involving methyl or ethyl acetate, esterification, and synthesis of capric acid–isoamyl alcohol esters in nonaqueous media.