中孔分子筛HMS负载钴催化剂在费-托合成中的应用:载体HMS的孔径对钴基催化剂性能的影响

 用不同链长度的十二胺，十四胺，十六胺和十八胺等伯胺为模板\r\n剂合成了具有不同孔径大小的HMS中孔分子筛．XRD和低温氮吸附测定表\r\n明，HMS具有典型的中孔分子筛特征，且其孔径大小随HMS合成中所用模\r\n板剂链长度的增加而增加．以HMS为载体，采用孔体积浸渍法制备了负\r\n载量为7．5％的钴催化剂，在接近工业试验条件下（n（H2）／n（CO）\r\n＝2．1，GHSV＝500h－1，p＝2．0MPa，θ＝227℃）考察了载体孔径大\r\n小对费－托合成反应性能的影响．结果表明，与常规的SiO2载体相比，\r\nHMS负载钴催化剂具有更高的催化活性和C5＋选择性；而且，CO转化率\r\n，C5＋选择性及产物中的蜡油比均随着HMS载体孔径的增大而升高．以\r\n7．5％Co／HMS－18为催化剂，CO转化率为78．0％，C5＋选择性为80．\r\n8％，蜡油比为11．1．     

纳米二氧化锆催化剂上一氧化碳加氢合成异丁烯

 考察了纳米ZrO2的制备方法及Al2O3和KOH助剂的添加对ZrO2催化\r\nCO加氢合成异丁烯反应的影响．纳米ZrO2的制备方法对ZrO2的物理性质\r\n和催化性能有较大的影响．用超临界流体干燥法干燥并在流动N2气氛中\r\n焙烧制得的ZrO2催化剂对异丁烯具有较高的选择性．Al2O3和KOH助剂表\r\n现出非常优良的助剂效应，在大幅度提高催化剂对i－C4烃选择性的同\r\n时保持了和ZrO2同样高的催化活性．催化剂的酸碱性表征结果表明，酸\r\n碱性对催化剂的催化性能影响很大，催化剂上适宜的酸碱数量和酸碱比\r\n例是影响其催化CO加氢合成异丁烯性能的非常重要的因素．     

HY沸石上2,6-二叔丁基萘的择形合成

 研究了脱铝HY沸石（n（Si）／n（Al）＝3．8）上萘（naph）的\r\n选择性叔丁基化反应．结果表明，八面沸石对该反应过程有较好的择形\r\n催化作用，两种异构化产物（2，6－二叔丁基萘和2，7－二叔丁基萘）\r\n之间存在着热力学平衡，即两种异构化产物可在酸性中心位上相互转化\r\n．在以叔丁醇为烷基化试剂，WHSV＝2h－1，n（t－BuOH）／n（naph）\r\n＝3，反应温度为120℃的反应条件下，萘的转化率可达98．43％，β－\r\n位选择性可高达100％，二叔丁基萘收率可达74．34％，2，6－二叔丁\r\n基萘／2，7－二叔丁基萘质量比为6．24．     

硝基苯加氢合成对氨基酚用负载铂催化剂的制备

 用甲醛还原沉积法制备了活性炭负载的铂催化剂（Pt／AC）和不\r\n同载体负载的铂催化剂，并考察了催化剂对硝基苯加氢制备对氨基酚反\r\n应的催化性能．结果表明，还原Pt（Ⅳ）的甲醛用量是影响催化剂性能\r\n的关键因素，甲醛必须过量而且存在一个最佳值．增加催化剂的铂负载\r\n量，不能有效提高加氢反应速度，反而易降低对氨基酚选择性；低铂负\r\n载量催化剂具有较高的活性、选择性及稳定性．XPS和TEM表征结果表明\r\n，金属铂集中分布于活性炭颗粒外部，其颗粒大小介于2～12nm间．炭\r\n载体催化剂的活性和选择性明显高于金属氧化物载体催化剂．掺入适量\r\n的Mg可显著提高Pt／AC催化剂的活性和选择性．     

沸石负载的钒络合物催化剂对烷烃氧化反应的催化性能

 将钒氧吡啶甲基络合物VO（pic）2负载于Y及ZSM－5沸石分子筛\r\n中，制备出沸石负载的钒络合物催化剂．用X射线衍射、电子自旋共振\r\n、红外光谱和元素分析等方法对催化剂进行了表征．结果表明，VO（p\r\nic）2络合物确实负载于分子筛孔道内，负载后的络合物仍保持着原来\r\n的结构．考察了催化剂对正己烷和环己烷氧化反应的催化性能，发现沸\r\n石分子筛负载的VO（pic）2络合物催化剂保留有络合物原有的催化性能\r\n，虽然催化活性有所下降，但显示出较好的形状选择性．与未负载的络\r\n合物相比，NaY和ZSM－5沸石负载的VO（pic）2络合物催化剂对正己烷\r\n氧化反应的伯醇选择性分别提高了2～3倍和5～6倍．     

正丁烷氧化制顺酐流化床催化剂的性能

 考察了前驱体制备过程中水合肼／五氧化二钒摩尔比（以下简记\r\n为n（N2H4）／n（V2O5））对催化剂性能的影响．由较高的n（N2H4）\r\n／n（V2O5）比制得的催化剂，其（VO）2P2O7相含量较多，正丁烷转化\r\n率较高．随着n（N2H4）／n（V2O5）比的减小，δ－VOPO4相的含量逐\r\n渐增多，正丁烷转化率随之升高；而顺酐选择性开始时升高，达到最大\r\n值后逐渐降低．在n（N2H4）／n（V2O5）＝0．34时制备的催化剂最佳\r\n，在丁烷浓度为4．0％、空速为500h－1及反应温度为420℃的反应条件\r\n下，顺酐收率可达49．74％．本文中细粒床催化剂有较大的操作弹性．     

钼催化剂上甲醇直接气相羰基化活性与吸附的关系

 制备了一系列非负载的钼催化剂，考察了催化剂上甲醇直接气相\r\n羰化活性与反应物及产物吸附的关系．结果发现，催化剂的制备方法对\r\n甲醇直接气相羰化活性的影响很明显，以纯二硫化钼试剂制备的催化剂\r\n，甲醇转化率与羰化产物乙酸甲酯的选择性最低；以三氧化钼气相还原\r\n硫化制备的催化剂，其羰化活性较低；以钼酸铵溶液经硫化铵溶液或硫\r\n化氢气体硫化制得的催化剂，其性能明显优于前两种，尤以钼酸铵经硫\r\n化铵溶液硫化制得的催化剂的性能最佳．催化剂的羰化活性明显依赖于\r\n催化剂的吸附性能，羰化活性高的催化剂不仅吸附CO的量大，而且对甲\r\n醇和乙酸甲酯的吸附量也明显较大．     

制备蜂窝状筛网进行NH3选择性催化还原NO的反应

 制备了蜂窝状筛网催化剂，并用于以NH3为还原剂选择性催化还\r\n原NO的反应．蜂窝状筛网催化剂具有热响应迅速、传质系数较高、压力\r\n降适中、机械强度较高、几何可变形性、抗热震性能好、催化剂回收简\r\n便和成本较低等一系列优点．阐述了蜂窝状筛网催化剂的制备工艺，并\r\n采用扫描电镜、比表面积测定、X射线衍射、活性评价等手段考察了筛\r\n网预处理方法对其催化活性的影响．实验结果表明，最佳的预处理方法\r\n是首先经稀酸刻蚀，然后于500℃下焙烧20h．     

表面键联型TiO2/SiO2固定化催化剂的结构及催化性能

 采用浸渍法制备了表面键联型TiO2／SiO2固定化光催化剂．XRD\r\n,FT－IR,XPS和BET比表面积测定结果表明,TiO2通过Ti－O－Si联结\r\n负载于多孔硅胶的表面,由此提出TiO2／SiO2的结构模型．考察了多孔\r\n硅胶的粒度及氧化钛负载量对催化剂活性的影响．对活性艳红K－2G（\r\nR15）的光催化脱色反应,最佳的光催化剂30％TiO2／SiO2（Ims30）比\r\nB－TiO2粉末的催化速率快3倍．随着载体粒度的减小,催化剂的比表面\r\n积增大,催化活性升高;多孔硅胶不仅起着支持体的作用,而且具有分\r\n散的作用;多孔硅胶具有很好的透光性．经ξ－电位测定,所制备催化\r\n剂的等电点为3．0pH单位,表明催化剂表面呈酸性．     

异戊二烯催化脱氢环氧化的研究

 合成了钼－乙酰丙酮配合物，并进行了表征，确定了其组成为M\r\noO2（acac）2．以MoO2（acac）2为催化剂，以过氧化氢为氧化剂，对\r\n异戊二烯一步脱氢环氧化制3－甲基呋喃反应进行了研究．考察了反应\r\n条件（催化剂用量、反应底物之比、温度、时间、溶剂和助剂等）对该\r\n反应的影响．结果表明，在n（cat）∶n（CH2∶C（CH3）CH∶CH2）∶\r\nn（H2O2）＝1∶100∶100，θ＝40℃，t＝6h的反应条件下，异戊二烯\r\n转化率为70．8％，3－甲基呋喃选择性为54．8％．提出了异戊二烯脱\r\n氢环氧化可能的反应机理．     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

氯氧化镁生成热的研究

用氧化镁氯化镁水溶液制备了8水合氯氧化镁[nMg(OH)2·MgCl2·8H2O], 并测定了其在盐酸中的溶解热, 实验结果表明, 氯氧化镁溶解热与n值呈线性关系, 根据溶解热求出5Mg(OH)2·MgCl2·8H2O和3Mg(OH)2·MgCl2·8H2O的生成热分别为-7727.1和5888.1kJ·mol^1^-。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Synthesis of phenolic components of Grains of Paradise

Two vanilloids, (5E)-8-(4-hydroxy-3-methoxyphenyl)oct-5-en-4-one (1) and 4-[3-hydroxydecyl]-2-methoxyphenol (2), isolated from the dried seeds of Grains of Paradise (Aframomum melegueta), were synthesized; the latter compound was made as the S-enantiomer and the material derived from the seeds was found to be a 1:1.7 mixture of the R and S isomers. The synthetic route used should allow the preparation of analogs having extended alkyl chains and consequently different lipophilicity, and 3, a homolog of 2, was also prepared.     

Acid hydrolysis of carboxymethylcellulose of low degree of substitution

Cotton cellulose was swollen in a sodium hydroxide solution and carboxymethylated by a two-bath method for different periods of time for each process. The kinetics of acid hydrolysis and the crystallinity of the swollen and carboxymethylated samples were measured. The proportion of broken bonds, rate constants for hydrolysis, and permeability of cellulose to hydrolyzing agents were calculated. The susceptibility of glycosidic linkages to acid hydrolysis was improved by carboxymethylation more than by swelling in alkali. The increased accessibility of carboxymethylcellulose to acid was regarded as a consequence of increased intra-and intercrystalline swelling and of the glycosidic bonds' weakness caused by the electron-attracting carboxymethyl group on the C-6 position.     

Estimation of Kinetic Parameters of Thermal Oxidation of Ilmenite

The aim of the presented work was the investigation of thermal oxidation of ilmenite in static air atmosphere. The investigations were carried out by use of a derivatograph (MOM, Hungary). The changes of crystallographic structure of investigated samples were identified by X-ray diffractometry on Philips PW-1710 diffractometer. In temperature above 500°C appears structure of hematite Fe₂O₃. On the basis of the thermogravimetric measurements, the contracting area and contracting volume models were found as the best fitting experimental data. This revised version was published online in August 2006 with corrections to the Cover Date.     

Mechanism of action of base-catalyzed oxygenation of phenol derivatives

Cyclopropyl derivative of 2,6-di-tert-butylphenol is synthesized as a probe to investigate the mechanism of base-catalyzed autooxidation of phenol derivatives. Our study indicates that one electron reduction of molecular oxygen from phenolate gives phenoxyl radical 3, a key intermediate of autooxidation. The coupling of phenoxyl radical and superoxide radical gives peroxylate anion 4 and produces the final epoxy alcohol adduct 6.     

Study of hydration of two cements of different strengths

Main hydration products of two cement pastes, i.e. CSH-gel, portlandite (P) (and specific surface S) were studied by static heating, and by SEM, TEM and XRD, as a function of cement strength (C-33 and C-43) hydration time (th) and subsequent hydration in water vapour.Total change in mass on hydration and air drying, M_o, increased with strength of cement paste and with hydration time. Content of water escaping at 110 to 220°C, defined as water bound with low energy, mainly interlayer and hydrate water, was independent on cement strength but its content increased with (th). Content of chemically bound (zeolitic) water in CSH-gel, escaping at 220-400°C, was slightly dependent on strength and increased with (th). It was possibly derived from the dehydroxylation of CSH-gel and AFm phase. Portlandite water, escaping at 400-500°C, was independent on cement strength and was higher on longer hydration. Large P crystals were formed in the weaker cement paste C-33. Smaller crystals were formed in C-43 but they increased with (th). Carbonate formated on contact with air (calcite, vaterite and aragonite), decomposed in cement at 600-700^oC. It was high in pastes C-33(1 month) and C-43(1 month), i.e. 5.7 and 3.3%, respectively; it was less than 1% after 6 hydration months (low sensitivity to carbonation) in agreement with the XRD study showing carbonates in the air dry paste (1month), and its absence on prolonged hydration (6 months) and on acetone treatment. Water vapour treatment of (6 months) pastes or wetting-drying increased this sensitivity.Nanosized P-crystals, detected by TEM, could contribute to the cement strength; carbonate was observed on the rims of gel clusters.This revised version was published online in November 2005 with corrections to the Cover Date.     

化学计量中不确定度评定研究进展

测量不确定度是表征合理地赋予被测量之值的分散性的参数。本文针对化学计量不确定度评定基础模型仅适用于线性模型、概率分布为正态分布或缩放位移t分布等局限,介绍了近年来不确定度评定的研究热点:蒙特卡罗方法(Monte Carlo Method,MCM),不确定度评定的来源、评定概念、评估方法及其发展过程,扩大了测量不确定度评定与表示的适用范围。     

微量钙的测定方法研究进展

介绍了1995-2006年期间测定微量和痕量钙的方法,如电感耦合等离子体-原子发射光谱法、原子吸收光谱法以及离子色谱法等的工作原理和特点,并说明了其测定微量钙的应用领域。并对微量钙的测定技术进行了展望(引用文献55篇)。