热及水热处理对SAPO—5分子筛结构的影响

对合成的ＳＡＰＯ－５分子筛进行了高温和水热处理，并用ＩＲ，ＸＲＤ和ＭＡＳ ＮＭＲ对处理过的分子筛进行了表征。结果表明，短时间的高温焙烧并不破坏分子筛的结构，而使分子筛中的骨架元素Ｐ，Ａｌ和Ｓｉ发生重构；长时间的高温焙烧使分子筛的结晶度降低，主要是由于Ｐ和Ａｌ游离出分子筛的骨架而形成磷酸铝盐。水热处理使分筛的Ｓｉ经历一个转晶和重构过程，在使ＳＡＰＯ－５分子筛结构更加完整的同时，未完全结晶的杂质形成了     

焙烧对HZSM—5分子筛结构的影响

运用魔角自转固态核磁共振谱（ＭＡＳ－ＮＭＲ），研究了焙烧对ＨＺＳＭ－５分子筛结构的影响，结果表明，高温焙烧将引起ＨＺＳＭ－５分子筛骨架的脱铝，当焙烧温度从５００℃增加到７００℃时，ＨＺＳＭ－５的骨架Ｓｉ／Ａｌ比由１６．７增加至２２．７；而当焙烧温度由７００℃到８００℃时，骨架Ｓｉ／Ａｌ比则由２２．７增加到４８．５，Ａｌ－ＭＡＳＮＭＲ结果表明，从骨架上脱下来铝，部分地形成了ＮＭＲ不可见的无定形态，随     

焙烧对HZSM－5分子筛结构的影响

运用魔角自转固态核磁共振谱（ＭＡＳ－ＮＭＲ），研究了焙烧对ＨＺＳＭ－５分子筛结构的影响．结果表明，高温焙烧将引起ＨＺＳＭ－５分子筛骨架的脱铝，当焙烧温度从５００℃增加到７００℃时，ＨＺＳＭ－５的骨架Ｓｉ／Ａｌ比由１６．７增加至２２．７；而当焙烧温度由７００℃到８００℃时，骨架Ｓｉ／Ａｌ比则由２２．７增加到了４８．５．２７Ａｌ－ＭＡＳＮＭＲ结果表明，从骨架上脱下来的铝，部分地形成了ＮＭＲ不可见的无定形态．随着焙烧温度的升高，ＮＭＲ不可见铝增多     

SAPO-34分子筛晶化机理的研究

采用ＸＲＤ，ＳＥＭ，ＩＲ和ＣＰ／ＭＡＳ及ＭＡＳＮＭＲ等手段，对快速水热合成ＳＡＰＯ３４分子筛的全过程进行了监测，研究了由原始凝胶到ＳＡＰＯ３４结晶体过程中固相物质的组成结构随晶化时间的变化规律．结果表明，ＳＡＰＯ３４晶核的形成过程既是一个硅氧、磷氧和铝氧四面体由无序排列的胶团到有序排列的晶格骨架的重排过程，同时又是羟基缔合脱水环化的过程．晶化分为晶化前期和晶化后期两个阶段．晶化前期，硅原子直接参与晶核的形成和晶粒的长大过程，生成Ｓｉ（４Ａｌ）结构；晶化后期，少量硅以同时取代一对磷铝原子的方式进入分子筛骨架形成Ｓｉ（３Ａｌ），Ｓｉ（２Ａｌ），Ｓｉ（１Ａｌ），Ｓｉ（０Ａｌ）等多种硅结构．但在整个晶化过程中Ｓｉ（４Ａｌ）结构的生成并不排除硅单独取代磷机理的共同作用．     

硅源及晶化时间对SAPO-5分子筛结构及性质的影响

分别以硅凝胶和正硅酸乙酯为硅源，通过改变晶化时间合成了系列ＳＡＰＯ５分子筛．用ＸＲＤ，ＭＡＳＮＭＲ和ＳＥＭ对分子筛的结构和形貌进行了表征．结果表明，以硅凝胶为硅源时，凝胶中的铝有３种面体配位状态．加热晶化很容易使凝胶转化为ＳＡＰＯ５分子筛，合成物的晶形更加规则．在４８ｈ内，延长晶化时间有助于硅进入分子筛骨架，使残余的Ａｌ２Ｏ３·Ｈ２Ｏ进一步反应，使骨架硅和铝的面体配位环境更加对称；超过４８ｈ后，硅开始游离出分子筛骨架，并使部分ＳＡＰＯ５转化为ＳＡＰＯ３４．以正硅酸乙酯为硅源时，硅和铝的反应活性均较低，凝胶中ＡｌＰＯ４及Ａｌ２Ｏ３·Ｈ２Ｏ的量均比四面体配位铝的量大．只有当晶化时间超过４８ｈ时，反应物中Ａｌ２Ｏ３·Ｈ２Ｏ才能完全转化．在此反应体系中，延长晶化时间有助于ＳＡＰＯ５的生成，使分子筛骨架硅的取代量更大，晶形更加规则，骨架铝的对称性更好．     

SAPO-34分子筛晶化过程中硅进入骨架的方式和机理

采用 Ｘ Ｒ Ｄ, Ｓ Ｅ Ｍ, Ｉ Ｒ 和 Ｎ Ｍ Ｒ 等手段考察了 Ｓ Ａ Ｐ Ｏ３４ 分子 筛的晶化过 程,深入研 究了晶化过程中硅进入 Ｓ Ａ Ｐ Ｏ３４ 晶格 骨架的方式和机理． 结果表明 ,在 Ｓ Ａ Ｐ Ｏ３４ 分子筛的整个晶化过程中没有 Ａｌ Ｐ Ｏ３４ 分 子筛晶相生成． 在 初始 凝 胶的 制备 过 程中, 模板 剂 的添 加和 混 合凝 胶的 老 化处 理对 Ｓ Ａ Ｐ Ｏ３４ 晶化过程的进行起着关键性的作用． 晶化前 期（ ＜ ２５ ｈ） , 硅原子直接参与晶核的形成和晶粒的长大过程,形成 Ｓｉ（４ Ａｌ） 结构,此阶段基本上 可以排除硅取代磷机理的作用; 晶化后期（ ＞ ２５ ｈ） ,少量硅以取代方式进入分子 筛骨架形成 Ｓｉ（ ｎ Ａｌ）（ ｎ ＝ ０ ～４） 多种硅结构     

Mo／USY催化剂中USY骨架结构稳定性对MoO3烧结行为的影响

应用ＸＲＤ、ＸＰＳ、ＩＲ、＾２９ｓＩＭＡＳＮＭＲ，＾２７ＡｌＭＡＳＮＭＲ和ＮＯ－ＩＲ吸附等手段对一系列经不同温度焙烧的Ｍｏ／ＵＳＹ催化剂中ＵＳＹ骨架结构破坏过程和Ｍｏ在ＵＳＹ分子筛中的烧结行为进行了研究。结果表明，Ｍｏ在ＵＳＹ上分散和烧结时，存在一个Ｍｏ对ＵＳＹ分子筛骨架铝的抽提过程，Ｍｏ和ＵＳＹ分子筛表面分散时，抽提该分筛骨架Ｓｉ（２Ａｌ）中少量的Ａｌ，但当焙烧温度升高，Ｍｏ开始烧结时，Ｍｏ主要     

氟氯有机化合物对HZSM-5分子筛改性过程中氟和氯的作用

利用ＸＲＤ，ＭＡＳ，ＮＭＲ，ＩＲ和ＸＰＳ等手段研究了ＣＦ４－ｎＣｌｎ改性的ＨＺＳＭ－５分子筛的体相和表面结构的变化。结果表明，改性过程中Ｆ和Ｃｌ均能使ＨＺＳＭ－５脱铝和脱硅。Ｃｌ可以使沸石骨架ＳｉＯ２／Ａｌ２Ｏ３升高，而Ｆ除使沸石骨架脱铝外，还会极化其晶格。Ｆ比Ｃｌ更容易在沸石表面富集。Ｆ和Ｃｌ是通过取代Ｏ或ＯＨ与沸石表面Ｓｉ或Ａｌ作用的。改性后的沸石表面有数种含氟表面物种存在。     

27Al和29Si MAS-NMR对Mo/HZSM-5催化剂的研究

使用＾２９Ａｌ固体离分辨核磁技术对甲烷无氧芳构化催化剂Ｍｏ／ＨＺＳＭ－５分子筛进行了研究，发现ＨＺＳＭ－５分子筛本体中仅含有少量非骨架Ａｌ，Ｍｏ物种与分子筛骨架Ａｌ的相互作用随Ｍｏ担载量以及焙烧的温度的升高而增加，在高温焙烧下，Ｍｏ物种会使分子筛骨架严重脱铝，并且生成Ａｌ２（ＭｏＯ４）３新相，最终导致分子筛骨架塌陷，催化性能下降。     

凝胶中硅含量对SAPO-5分子筛合成及其性能的影响

通过改变反应物凝胶中的硅含量，用水热法合成了系列ＳＡＰＯ－５分子筛，并用ＸＲＤ、ＳＥＭ和ＭＡＳＮＭＲ分别研究了不同硅含量的分子筛结构和形貌．以正己烷的催化裂解为模型反应，用微反色谱研究了不同硅含量的ＳＡＰＯ－５分子筛的催化性能．结果表明，分子筛骨架中的硅含量随反应物中硅含量的增加而增加；硅开始进入ＳＡＰＯ－５分子筛骨架时，是以取代单个磷原子而进行的；当反应物中硅含量较高时，硅进入分子筛骨架是通过两个硅原子取代一对铝和磷原子，从而在ＳＡＰＯ－５中形成富硅区．硅进入分子筛骨架，虽然未改变分子筛的晶体结构，但改变了分子筛的晶形晶貌．ＳＡＰＯ－５分子筛中存在３种酸中心，即弱酸、中强酸和强酸中心．在正己烷催化裂解中，较低温度时，催化活性中心主要是中强酸中心；当反应温度较高时，弱酸中心也可充当活性中心．在强酸中心上易发生结炭现象．     

辐射技术在环境保护中的应用

由于高能电子束和γ射线本身具有的特性,其辐射技术在环境保护领域具有巨大的应用潜力。本文介绍了国内外利用辐射技术在废水、废气和固体废物(“三废”)处理中的研究和应用,涉及印染废水、造纸废水、硝基苯胺类物质、卤系阻燃剂类物质、环境内分泌干扰物和藻毒素的处理,燃煤尾气脱硫脱硝,以及挥发性有机物、污泥等方面的处理研究,并对辐射处理各种有机污染物的机理进行了探索和分析。表明辐射技术是处理“三废”的一种十分有效的方法。同时,讨论了辐射技术在环境处理应用中的有限性,并对该技术的研究和发展方向进行了展望。     

全科医生对社区糖尿病患者的防治

目的探讨和分析全科医生在社区糖尿病患者疾病防治中的效用。方法以2015年1月—2016年12月期间深圳市坪山新区人民医院碧岭社康中心管理的180例糖尿病患者为研究对象,并采用随机分组的方法分为观察组(n=90)和对照组(n=90),其中,观察组患者予以药物治疗,对照组患者予以非药物治疗,并观察和比较两组患者治疗前后的各种代谢指标。结果无论是在接受全科医生指导前还是指导后,观察组患者空腹血糖值和餐后2 h血糖值均明显低于对照组,且差异均具有统计学意义(P<0.05);观察组患者的糖化血红蛋白值、尿微量蛋白值、收缩压和舒张压值以及体质量指数明显低于对照组,且差异均具有统计学意义(P<0.05)。结论实施药物治疗的糖尿病患者的各项血糖及代谢指标均低于非药物治疗组的数值,全科医生在社区糖尿病患者的防治中发挥着一定的积极效用。     

Advanced mass spectrometric methods applied to the study of fate and removal of pharmaceuticals in wastewater treatment

This overview is of analytical methodologies based on gas chromatography-mass spectrometry and liquid chromatography-mass spectrometry, applied in environmental monitoring of pharmaceutical residues and their known degradation products. We also consider the ability of time-of-flight (TOF) and quadrupole-TOF instruments to provide sufficiently accurate-mass measurements and full-scan spectra for unequivocal confirmation of target compounds and investigation of their degradation products, which are either known or unknown.

We focus attention on the fate and the behavior of pharmaceutical residues during conventional and advanced wastewater treatments. Wastewater-treatment plants are designed to remove conventional pollutants (e.g., suspended solids and biodegradable organic compounds), but not low concentrations of synthetic pollutants (e.g., pharmaceutically active compounds).

Membrane bioreactor systems represent a new generation of processes that have proved to outperform conventional activated sludge treatment in terms of sludge production and effluent quality. In the past few years, there has been much attention paid to their capability for removing trace organic contaminants from sewage. This review highlights their improved performance in removing pharmaceutical residues from wastewater compared to conventional treatment.     

玻璃纤维表面的乙烯基单体接枝聚合

用玻璃纤维表面处理剂ＭＡＣ处理玻璃纤维后，再进行臭氧处理，使玻璃纤维的表面产生活性中心，引发苯乙烯、甲基丙烯酸甲酯、及丙烯酸等乙烯基单体在玻璃纤维表面上接枝聚合。接枝纤维的密度减小，对水的浸润性下降，红外光谱及扫描电镜观察证明玻璃纤维表面上接枝聚合物的存在。     

Influences of acid and heat treatments on the structure and water vapor adsorption property of natural zeolite

Natural zeolite was first acid treated and then heat treated. The influences of acid and heat treatments on the structure and water vapor adsorption property of natural zeolite were investigated. X‐ray photoelectron spectroscopy (XPS), X‐ray diffraction (XRD), thermogravimetric analysis (TG), and Brunauer‐Emmett‐Teller (BET) surface areas were employed to investigate the structure changes of the zeolite samples. Water vapor adsorption property of the samples was investigated in order to determine wettability of the samples. The results showed that nitric acid treatment could remove Al from the structure, decrease relative crystallinity, and significantly increase specific surface area of the zeolite samples. Heat treatment could change or even destroy the structure, effectively remove water molecules from the surface/structure, and decrease the specific surface area of the zeolite samples. Water vapor adsorptions on the acid‐treated zeolite samples were significantly lower than that for the zeolite sample, and the adsorptions further reduced for the heat‐treated zeolite samples. The increase of Si/Al ratio, decreases of silanol groups, and specific surface area of the samples were major reasons related to the reductions of water vapor adsorptions on the zeolite samples.     

Evaluation of the Secondary Pore Structure of Hydrothermally- and Acid-treated Faujasite Type Zeolites

With regard to H-Y type zeolites dealuminated by hydrothermal and acid treatments, their physical properties were characterized by measurements of 29Si- and 27Al-MAS-NMR, IR, and X-ray diffraction. The secondary pores were quantitatively analyzed by the t-plot method for nitrogen adsorption isotherm at liquid nitrogen temperature and were then compared with the results of samples dealuminated by SiCl4 treatment.The plateau region of the nitrogen adsorption isotherm diminished as hydrothermal and acid treatments proceeded, with the result that the shape of the t-plot changed to that of three straight sections. This t-plot shape suggested that the secondary pores with relatively consistent sizes could develop with the progress of the treatment. On the other hand, SiCl4 treatment was found to produce less secondary pores than hydrothermal and acid treatments. The surface area of micropores calculated from the t-plots gave a considerably higher value than values obtained from the BET equation and from that calculated geometrically. This is attributable to the micropore filling effect.     

先锋褐煤的热处理和水热处理改质

通过先锋褐煤热处理和水热处理,结合处理煤结构与性质表征,研究了热处理和水热处理对先锋褐煤结构、抽提和溶胀性能的影响,探讨了热处理过程水的作用。结果表明,低于热解温度下的热处理以非共价键解缔合及部分弱共价键热解为主,水与煤的水热反应能够抑制水热处理过程中煤的热解和小分子化合物释放。高温热处理以热解和脱氧为主,水热反应可以稳定煤热解活性基团,避免其二次裂解和交联,在一定程度上提高处理煤的混合溶剂抽提率,改善其溶胀性能。     

酸碱改性HZSM-5分子筛上甲醇制取均四甲苯的研究

对HZSM-5分子筛进行"酸碱两步改性",制备得到了H(0.2)-Na-ZSM-5、H(0.5)-Na-ZSM-5、H(0.2)-K-ZSM-5和H(0.5)-K-ZSM-5四种催化剂。通过XRD、NH₃-TPD、ICP、FT-IR与Py-IR方法对催化剂进行表征,并在连续流动固定床反应装置上对催化剂进行评价。实验结果表明,H(0.2)-K-ZSM-5催化剂由于其孔径变大、弱的B酸量增多,从而提高了均四甲苯的选择性。     

An investigation of post treatment on properties and structure of ultrahigh molecular weight polyethylene parts prepared by selective laser sintering for biomedical application

Combined with customization advantage of selective laser sintering (SLS) and excellent performance of ultrahigh molecular weight polyethylene (UHMWPE), it is possible to meet the requirements of artificial joints for biomedical application. However, high viscosity of UHMWPE melt limits the strength of UHMWPE sintered parts. Inspired from metal and ceramic materials, this work aims to improve the performance of UHMWPE parts prepared by SLS using post treatment methods, including heat treatment and hot isostatic pressure (HIP) treatment. Consequently, HIP treatment shows superiority on promoting the performance of UHMWPE sintered parts compared with heat treatment. With the condition of temperature and isostatic pressure, a novel definition of “bonding neck” is given to explain the enhancement of cohesion between each UHMWPE particle in different post treatment. Without any fortifier, the biological safety of artificial joints manufactured by SLS is further guaranteed. Under the isostatic pressure of 12 MPa and temperature of 185°C in HIP treatment, the mechanical strength, tribological performance and other properties are improved dramatically. The tensile strength of the specimen is up to 8.0 MPa, the elongation at break is 99.3%, the impact strength is 8.8 MPa, the friction coefficient is 0.11, the wear rate is 9.3 × 10^?4 mm³/Nm and samples do not show cytotoxicity at the same time.     

Effect of mild solvent post-treatments on the gas transport properties of glassy polymer membranes

This study examines the effect of treatment of defective glassy polymer membranes with a variety of vapors and liquids which have varying solvency power for the polymer. The pure-gas oxygen/nitrogen selectivities of defective, asymmetric membranes are shown to be permanently increased, in special cases, by treatment with certain solvents which have adequate solvency power to cause a critical level of swelling in the membrane skin layer. Three distinct types of membranes have been treated; asymmetric polysulfone membranes formed by dry/wet phase inversion, spin-coated poly(phenylene oxide)-ceramic composite membranes and solution-deposited polyimide-ceramic composite membranes. While the detailed fundamental processes controlling the elimination of surface defects are complex, our results suggest that plasticization of the selective skin layer, coupled with surface-tension driven cohesive forces are likely to be the key factors at play.