Correction function on biased results due to matrix effects: Application to the routine analysis of pesticide residues

A new strategy to carry out the correction of analytical results affected by systematic errors due to the matrix effect is proposed. Two types of external calibrations must be established with the purpose to estimate the matrix effect: solvent calibration (SC) and matrix-matched calibration (MC). These calibration curves are statistically compared and a correction function (CF) is proposed with the aim to simplify the resolution to the problems associated with the incidence of matrix systematic error in the analytical results. Applying this correction function to the results obtained from the solvent calibration, it is possible to make a prediction of the values that would be obtained when the matrix-matched calibration is applied. On the other hand, a rigorous study of the associated uncertainty is developed and applied to the calculated correction function. Finally, this correction function is validated by means of obtained data of recovery studies carried out by a traditional methodology. The methodology has been satisfactorily applied to the quantification of the pesticide procymidone by HPLC for assessing dermal exposure.     

Alternative calibration approaches to compensate the effect of co-extracted matrix components in liquid chromatography-electrospray ionisation tandem mass spectrometry analysis of pesticide residues in plant materials

The aim of this study was to evaluate the applicability of different calibration approaches in a multi- and single-residue analysis of modern pesticides in plant matrices using liquid chromatography-electrospray mass spectrometry (HPLC-ESI-MS). In the first set of experiments the determination of eight pesticides representing different groups of polar/unstable pesticides (carbamates, benzimidazoles, azoles, benzoylphenylurea) in apple samples was performed. The trueness and precision of data obtained by using: (i) external solvent standard calibration, (ii) external matrix-matched standard calibration and (iii) echo-peak internal standard calibration was compared. The last mentioned method is a novel technique providing the possibility to inject internal standard of the same identity as a target analyte, so that its retention time is close to the analyte from the sample. According to expectation, when using external standard solvent calibration the results were under- or overestimated due to suppression or enhancement of analyte's signal by matrix components. On the other hand with the use of matrix-matched calibration accurate data were obtained. With echo-peak technique accurate results comparable to those obtained by matrix calibration were obtained for six out of eight pesticides. In the second set of experiment we used the echo-peak technique to overcome the problem with the response instability in the analysis of chlormequat in pear concentrate samples. As an internal standard method the echo-peak technique provided the possibility of monitoring of signal decrease during the analytical sequence and to compensate this decrease by relating sample peak area relatively to this internal standard.     

Estimation and correction of matrix effects in gas chromatographic pesticide multiresidue analytical methods with a nitrogen-phosphorus detector

The assessment of matrix effects in the quantification of organophosphorus pesticides in fruit and vegetables by GC-NPD, were studied applying ANCOVA. Calibration curves prepared in solvent were compared with calibration curves prepared in a blank matrix extract for eight different commodities, establishing whether the matrix induces systematic or proportional errors in the quantification of the pesticides. In such cases correction functions were obtained and validated by quantifying spiked samples using solvent calibrations and applying the correction functions to the data obtained. The results were compared with those obtained by quantification using matrix-matching calibrations and with those from 100% recovery experiments. It was found that the matrix effects can be avoided using the correction functions. Finally the contribution of the correction functions to the uncertainty of the results was estimated as well as their stability during a four month period.     

Homogeneous sample preparation for automated high throughput analysis with matrix-assisted laser desorption/ionisation time-of-flight mass spectrometry

This work presents a simple method for obtaining homogeneous sample surfaces in matrix-assisted laser desorption/ionisation time-of-flight mass spectrometry (MALDI-TOFMS) for the automated analysis of peptides and proteins. The sample preparation method is based on applying the sample/matrix mixture onto a pre-deposited highly diluted matrix spot. The pre-deposited crystals act as seeds for the new sample containing crystals which become much smaller in size and more evenly distributed than with conventional methods. This 'seed-layer' method was developed, optimised and compared with the dried-droplet method using peptides and proteins in the 1000-20,000 Da range. The seed-layer method increases the surface homogeneity, spot to spot reproducibility and sample washability as compared with the commonly used dried-droplet method. This methodology is applicable to alpha-cyanohydroxycinnamic acid, sinapinic acid and ferulic acid, which all form homogeneous crystal surfaces. Within-spot variation and between-spot variation was investigated using statistics at a 95% confidence level (n = 36). The statistical values were generated from more than 5000 data points collected from 500 spectra. More than 90% of the sample locations results in high intensity spectra with relatively low standard deviations (RSDs). Typically obtained data showed an RSD of 19-35% within a sample spot as well as in-between spots for proteins, and an RSD of < or = 50% for peptides. Linear calibration curves were obtained within one order of magnitude using internal calibration with a point-RSD of 3% (n = 10). The sample homogeneity allows mass spectra (average of 16 laser shots) to be obtained on each individual sample within 15 sec, whereby a 100 spot target plate can be run in 25 min. High density target plates using the seed-layer method were prepared by spotting approximately 100 picoliter droplets onto the target, resulting in sample spots < or = 500 microns in diameter using a flow-through piezo-electric micro-dispenser. By using this automated sample preparation step lower standard deviations are obtained in comparison to manually prepared samples.     

Ionization enhancement in atmospheric pressure chemical ionization and suppression in electrospray ionization between target drugs and stable-isotope-labeled internal standards in quantitative liquid chromatography/tandem mass spectrometry

The phenomena of ionization suppression in electrospray ionization (ESI) and enhancement in atmospheric pressure chemical ionization (APCI) were investigated in selected-ion monitoring and selected-reaction monitoring modes for nine drugs and their corresponding stable-isotope-labeled internal standards (IS). The results showed that all investigated target drugs and their co-eluting isotope-labeled IS suppress each other's ionization responses in ESI. The factors affecting the extent of suppression in ESI were investigated, including structures and concentrations of drugs, matrix effects, and flow rate. In contrast to the ESI results, APCI caused seven of the nine investigated target drugs and their co-eluting isotope-labeled IS to enhance each other's ionization responses. The mutual ionization suppression or enhancement between drugs and their isotope-labeled IS could possibly influence assay sensitivity, reproducibility, accuracy and linearity in quantitative liquid chromatography/mass spectrometry (LC/MS) and liquid chromatography/tandem mass spectrometry (LC/MS/MS). However, calibration curves were linear if an appropriate IS concentration was selected for a desired calibration range to keep the response factors constant.     

A comparative study of the correction of systematic errors in the quantitation of pyrethroids in vegetables using calibration curves prepared using standards in pure solvent

A comparative study of two mathematical approaches was performed in order to correct systematic errors due to the presence of the unexpected interferences which appear when the quantitation of the analyte in real samples is carried out with calibration curves built using standards in pure solvent. These methods consisted in the establishment of different mathematical expressions which transform the concentration (Cs) obtained using calibration graphs built using pure solvent into the corrected concentration (C(M)) that should be obtained if the quantitation is carried out with calibration curves built using standards dissolved in blank matrix extracts. In the two approaches the correction is performed from the results of an intermediate precision study which was carried out using both calibration graphs (prepared using pure solvent and blank matrix extract). By using ANCOVA to compare the slope of both solvent-based and matrix-matched calibration graphs, matrix effect was found in the determination of deltamethrin in tomato and acrinathrin in tomato and pepper. In these cases, both approaches led to good results.     

Validation of a Gas Chromatographic–Tandem Mass Spectrometric Method for Analysis of Pesticide Residues in Six Food Commodities. Selection of a Reference Matrix for Calibration

A gas chromatographic–tandem mass spectrometric (GC–MS–MS) method for analysis of 30 multi-class pesticide residues in four vegetables (cucumber, marrow, pepper, and eggplant) and two fruits (melon and watermelon) has been developed and validated. The performance characteristics linearity, detection limit (LOD), quantification limit (LOQ), precision, and recovery were studied. The effect of the matrix on the calibration step was studied by comparing calibration curves and recoveries for each food commodity. Two different food commodities, cucumber and watermelon, were selected as potential reference matrixes for the target vegetables and fruits, respectively.     

A new strategy of solution calibration in laser ablation inductively coupled plasma mass spectrometry for multielement trace analysis of geological samples

Because multielement trace analysis by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) is often limited by the lack of suitable reference materials with a similar matrix composition, a novel quantification strategy using solution calibration was developed. For mass spectrometric multielement determination in geological samples a quadrupole-based LA-ICP-MS is coupled with an ultrasonic nebulizer (USN). In order to arrange matrix matching the standard solutions are nebulized with a USN during solution calibration and simultaneously a blank target (e.g. lithium borate) is ablated with a focused laser beam. The homogeneous geological samples were measured using the same experimental arrangement where a 2% nitric acid is simultaneously nebulized with the USN. Homogeneous targets were prepared from inhomogeneous geological samples by powdering, homogenizing and fusing with a lithium borate mixture in a muffle furnace at 1050 degrees C. Furthermore, a homogeneous geological glass was also investigated. The quantification of analytical results was performed by external calibration using calibration curves measured on standard solutions. In order to compare two different approaches for the quantification of analytical results in LA-ICP-MS, measured concentrations in homogeneous geological targets were also corrected with relative sensitivity coefficients (RSCs) determined using one standard solution only. The analytical results of LA-ICP-MS on various geological samples are in good agreement with the reference values and the results of other trace analytical methods. The relative standard deviation (RSD) for trace element determination (N = 6) is between 2 and 10%.     

A new strategy of solution calibration in laser ablation inductively coupled plasma mass spectrometry for multielement trace analysis of geological samples

Because multielement trace analysis by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS) is often limited by the lack of suitable reference materials with a similar matrix composition, a novel quantification strategy using solution calibration was developed. For mass spectrometric multielement determination in geological samples a quadrupole-based LA-ICP-MS is coupled with an ultrasonic nebulizer (USN). In order to arrange matrix matching the standard solutions are nebulized with a USN during solution calibration and simultaneously a blank target (e.g. lithium borate) is ablated with a focused laser beam. The homogeneous geological samples were measured using the same experimental arrangement where a 2% nitric acid is simultaneously nebulized with the USN. Homogeneous targets were prepared from inhomogeneous geological samples by powdering, homogenizing and fusing with a lithium borate mixture in a muffle furnace at 1050?°C. Furthermore, a homogeneous geological glass was also investigated. The quantification of analytical results was performed by external calibration using calibration curves measured on standard solutions. In order to compare two different approaches for the quantification of analytical results in LA-ICP-MS, measured concentrations in homogeneous geological targets were also corrected with relative sensitivity coefficients (RSCs) determined using one standard solution only. The analytical results of LA-ICP-MS on various geological samples are in good agreement with the reference values and the results of other trace analytical methods. The relative standard deviation (RSD) for trace element determination (N = 6) is between 2 and 10%.     

Dansyl and dabsyl analytical constructs as tools for the accurate estimation of compounds in solid-phase synthesis

The presence of dansyl or dabsyl chromogenic moieties in a solid-phase analytical construct, an assembly of linkers/spacers/sensitizers for improving analytical characterization, allows the accurate estimation of products from solid-phase synthesis by UV detection during liquid chromatography-mass spectrometry analysis in the cleavage solution. The spectroscopic properties of dansylated molecules have been evaluated to verify the "compound-independent UV absorption" necessary for using the chromophore in the accurate estimation. First, measurements on commercial dansylated compounds were made, then a series of construct-like molecules were prepared by solution-phase synthetic procedures and their UV properties were determined. Compound calibration curves were determined, and UV absorption was shown to be both proportional to the compound concentration and compound-independent. An example of a dansyl construct derivative was then prepared on a polymeric matrix, and an accurate estimation using the calibration curves was carried out in the cleavage solution. Good agreement was found between the calculated amount of released compound using the UV calibration curves and the calculated amount using both (1)H NMR and LC/chemiluminescent nitrogen detection quantitative techniques. Preliminary studies using the dabsyl moiety as an improved chromophore with higher wavelength and extinction coefficient are also reported.     

Comparison of three colorimetric methods for the determination of manganese in freshwaters

Three calorimetric methods for the determination of manganese in freshwaters have been investigated and compared with the atomic-absorption spectrometry (AAS) method. Two of the methods, viz. the formaldoxime (FAD) and pyridylazonaphthol (PAN) methods were found to yield poor calibration curves upon standardization, and to have high average errors for the estimation of manganese concentrations in standard solutions. The FAD method, when applied to freshwater samples, was found to be subject to an interfering UV absorbance which could not be negated successfully by a reagent blank; the method thus tended to give high estimations at low concentrations of manganese, but the results obtained also appear to be very sensitive to the nature of the freshwater matrix. On the other hand the PAN method was found to give very high estimations for the concentration of manganese, in both standard solutions and in freshwater samples, owing to the nature of the absorbance of the ligand used for manganese determination. This method also appears to be affected by the freshwater matrix, leading to gross overestimation of manganese levels. A third method, based on a porphyrin ligand [T-(4-CP)P], was found to give results comparable with those of the AAS method in estimating the soluble manganese content in freshwaters.     

超高效液相色谱-四极杆-飞行时间质谱法快速筛查和确证渔药中86种非法添加化学品

建立了超高效液相色谱-四极杆-飞行时间质谱法快速筛查与确证渔药中86种非法添加禁限用药物的方法。渔药以80%(v/v)乙腈水溶液进行提取,通过稀释降低基质效应,采用ACQUITY PREMIER HSS T3色谱柱进行分离,以甲醇和0.1%甲酸水溶液作为流动相进行梯度洗脱,采用电喷雾双喷离子源(Dual AJS ESI)正离子模式分析检测。建立了86种药物的一级精确质量数据库和二级碎片质谱库。在全扫描采集模式下,以化合物的色谱保留时间、精确质量数、同位素分布和同位素丰度比定性;在Target MS/MS采集模式下,通过二级碎片离子的匹配进一步确证化合物,以准分子离子峰的峰面积定量,实现渔药样品中多目标药物的快速定性定量分析。86种药物在各自的线性范围内均呈现良好的线性关系,相关系数均大于0.99,中草药制剂和抗生素粉剂的定量限(LOQ)范围分别为1~15 mg/kg和5~75 mg/kg,添加回收率范围为76.8%~112.1%,相对标准偏差(RSD, n=3)小于11.7%。该方法快速、简便、准确、灵敏,适用于不同种类渔药中禁限用非法添加药物的高通量筛查。将该方法应用于浙江省渔用投入品质量安全监督抽检项目中,共筛查60个样品,其中8种中草药制剂筛查出说明书中未明确标明的药物成分,1种抗生素粉剂未检出有效成分。该研究为渔药的质量安全监控提供了有效的技术手段。     

Chemometric tools improving the determination of anti-inflammatory and antiepileptic drugs in river and wastewater by solid-phase microextraction and liquid chromatography diode array detection

An analytical method for the simultaneous determination of seven non-steroidal anti-inflammatory drugs (naproxen, ketoprofen, diclofenac, piroxicam, indomethacin, sulindac and diflunisal) and the anticonvulsant carbamazepine in river and wastewater is reported. The method involves pre-concentration and clean-up by solid-phase microextraction using polydimethylsiloxane/divinylbenzene fibers, followed by liquid chromatography with diode array detection analysis. Owing to the fact that river water samples did not contain interferences and no sensitivity changes due to sample matrix were observed, external calibration was implemented. Standardization was also applied in order to carry out the prediction step by preparing only two diluted standards that were subjected to the pre-concentration step and a set of standards prepared in solvent. For the analysis of wastewater samples, in contrast, it was necessary to implement standard addition calibration in combination with the multivariate curve resolution-alternating least squares (MCR-ALS) algorithm, which allowed us to overcome matrix effect and exploit the second order advantage. Recoveries ranging from 72% to 125% for all pharmaceuticals proved the accuracy of the proposed method in river water samples. On the other hand, wastewater sample recoveries ranged from 83% to 140% for all pharmaceuticals, showing an acceptable performance – considering this sample contains no modeled interferences.     

Calibration Measurements in laser-induced breakdown spectroscopy using nanosecond and picosecond lasers

The influence of laser pulse duration on laser-induced breakdown spectroscopy (LIBS) calibration curves is investigated in the present work. Two Nd:YAG lasers providing pulses of 35 ps and 5 ns, respectively, both operating at 1064 nm, have been used to create plasmas on aluminium, manganese, iron, and silicon targets and on prepared stoichiometric samples of these metals in a matrix. The time-resolved, space-averaged plasma temperatures have been deduced using Boltzmann plots, while the electron number density has been determined from the broadening of spectral lines. The effect of laser pulse duration on the plasma characteristics is discussed, and comparisons are made with previously reported data measured under similar experimental conditions. The optimum experimental conditions (i.e., time delay, gate width, laser energy) have been determined for reliable use of LIBS for quantitative analysis for both pulse durations. For each of the metals of interest, calibration curves have been constructed for concentrations ranging up to 2%.     

Design of multiplex calibrant plasmids, their use in GMO detection and the limit of their applicability for quantitative purposes owing to competition effects

Five double-target multiplex plasmids to be used as calibrants for GMO quantification were constructed. They were composed of two modified targets associated in tandem in the same plasmid : (1) a part of the soybean lectin gene and (2) a part of the transgenic construction of the GTS40-3-2 event. Modifications were performed in such a way that each target could be amplified with the same primers as those for the original target from which they were derived but such that each was specifically detected with an appropriate probe. Sequence modifications were done to keep the parameters of the new target as similar as possible to those of its original sequence. The plasmids were designed to be used either in separate reactions or in multiplex reactions. Evidence is given that with each of the five different plasmids used in separate wells as a calibrant for a different copy number, a calibration curve can be built. When the targets were amplified together (in multiplex) and at different concentrations inside the same well, the calibration curves showed that there was a competition effect between the targets and this limits the range of copy numbers for calibration over a maximum of 2 orders of magnitude. Another possible application of multiplex plasmids is discussed.     

Qualitative and quantitative analysis of pyrolysis oil by gas chromatography with flame ionization detection and comprehensive two-dimensional gas chromatography with time-of-flight mass spectrometry

Pyrolysis oils have attracted a lot of interest, as they are liquid energy carriers and general sources of chemicals. In this work, gas chromatography with flame ionization detector (GC-FID) and two-dimensional gas chromatography with time-of-flight mass spectrometry (GC×GC-TOFMS) techniques were used to provide both qualitative and quantitative results of the analysis of three different pyrolysis oils. The chromatographic methods and parameters were optimized and solvent choice and separation restrictions are discussed. Pyrolysis oil samples were diluted in suitable organic solvent and were analyzed by GC×GC-TOFMS. An average of 300 compounds were detected and identified in all three samples using the ChromaToF (Leco) software. The deconvoluted spectra were compared with the NIST software library for correct matching. Group type classification was performed by use of the ChromaToF software. The quantification of 11 selected compounds was performed by means of a multiple-point external calibration curve. Afterwards, the pyrolysis oils were extracted with water, and the aqueous phase was analyzed both by GC-FID and, after proper change of solvent, by GC×GC-TOFMS. As previously, the selected compounds were quantified by both techniques, by means of multiple point external calibration curves. The parameters of the calibration curves were calculated by weighted linear regression analysis. The limit of detection, limit of quantitation and linearity range for each standard compound with each method are presented. The potency of GC×GC-TOFMS for an efficient mapping of the pyrolysis oil is undisputable, and the possibility of using it for quantification as well has been demonstrated. On the other hand, the GC-FID analysis provides reliable results that allow for a rapid screening of the pyrolysis oil. To the best of our knowledge, very few papers have been reported with quantification attempts on pyrolysis oil samples using GC×GC-TOFMS most of which make use of the internal standard method. This work provides the ground for further analysis of pyrolysis oils of diverse sources for a rational design of both their production and utilization process.     

超高效液相色谱-四极杆飞行时间质谱法测定克氏螯虾中39种兽药残留

建立了超高效液相色谱-四极杆飞行时间质谱（UHPLC-Q-TOF-MS）快速筛查克氏螯虾中39种兽药残留的分析方法。样品经酸化乙腈提取,增强型脂质去除净化剂（EMR-Lipid）结合石墨化多壁碳纳米管（GMWNTs）净化,采用UHPLC-Q-TOF-MS分析检测。通过比对待测物准分子离子的精确质量数、同位素丰度比、保留时间等特征信息进行定性初筛,通过二级谱图谱库检索比对进行确证,通过一级提取离子色谱图峰面积进行定量分析。39种化合物在各自的浓度范围内均呈良好的线性关系,线性相关系数均大于0.99,定量限为3~15 μg/kg,添加回收率为62.4%~105.8%,相对标准偏差（RSD）为2.5%~13.5%,方法简便、快速、准确,可应用于克氏螯虾中喹诺酮类、磺胺类、三苯甲烷类39种药物残留的快速筛查定量。     

Chitosan and multi-walled carbon nanotube composite rods

<正>Multi-walled carbon nanotubes(MWNTs) and chitosan(CS) composite rods with layer-by-layer structure were prepared via in situ precipitation method.On the one hand,some MWNTs fragments with open tips played the role of nuclear agent to improve the crystallinity of CS.On the other hand,MWNTs embedded in CS matrix to absorb energy when the composite rods were destroying.Nanotubes pulled out from CS matrix,and lots of holes remained,so MWNTs could endure external stress effectively.The bending strength and bending modulus of CS/MWNTs rods(100/0.5,W/W) arrived at 130.7 MPa and 4.4 GPa respectively,increased by 34.3%and 7.3%compared with those of pure CS rods.Consequently, CS/MWNTs composite rods with excellent mechanical properties could be a novel device used for bone fracture internal fixation.     

Evaluation of three calibration methods to compensate matrix effects in environmental analysis with LC-ESI-MS

In quantitative analysis of environmental samples using high-performance liquid chromatography–electrospray ionization mass spectrometry (HPLC-ESI-MS) one of the major problems is the suppression or, less frequently, the enhancement of the analyte signals in the presence of matrix components. Standard addition is the most suitable method for compensating matrix effects, but it is time-consuming and laborious. In this study we compare the potential of three calibration approaches to compensate matrix effects that occurred when seven analytes (naphthalene sulfonates) were quantified in time series samples of waters with different matrices (untreated and treated industrial wastewater). The data obtained by external calibration, internal calibration with one standard, and external sample calibration (corresponding to matrix-matched calibration) were compared with those obtained by standard addition. None of the three approaches were suitable for a sample series of highly loaded, untreated wastewater with highly variable matrix. For less heavily loaded and less variable samples (treated wastewater effluents), the external sample calibration provided reasonable results for most analytes with deviations mostly below 25% as compared to standard addition. External sample calibration can be suitable to compensate matrix effects from moderately loaded samples with more uniform matrices, but it is recommended to verify this for each sample series against the standard addition approach.     

Proton sponge-functionalized silica as high performance adsorbents for solid-phase extraction of trace perfluoroalkyl sulfonates in the environmental water samples and their direct analysis by MALDI-TOF-MS

1,8-Bis(dimethylamino)naphthalene (DMAN), a classical 'proton sponge', was functionalized on silica particles as a novel solid-phase extraction (SPE) adsorbent (DMAN@silica) for extracting perfluoroalkyl sulfonates (PFSs). High reproducibility and excellent extraction capability for PFSs were obtained in a wide pH range (3.0~8.5). The adsorbed PFSs on DMAN@silica sorbents could be efficiently eluted by 1,8-bis(tetramethylguanidino)naphthalene (TMGN) solution which is a proton sponge with higher proton affinity than DMAN. The elution could be directly analyzed by MALDI-TOF-MS using TMGN as matrix. Clear mass spectra for the PFSs were obtained due to no matrix ions interference observed. Furthermore, a novel strategy based on the DMAN@silica-SPE enrichment, followed by MALDI-TOF-MS analysis, was proposed and applied for PFSs quantification in environmental water samples. The calibration curves of each of the target analytes showed a wide linear dynamic range of response (0.1-10 ng L(-1) for perfluorooctane sulfonate (PFOS), perfluorohexyl sulfonate (PFHxS) and perfluorobutylsulfonate (PFBS)), which were over 2 orders of magnitude. The detection limits for PFOS, PFHxS, and PFBS were 0.021, 0.016, and 0.013 ng L(-1), respectively (S/N = 3). Recoveries of PFOS, PFHxS, and PFBS are in the ranges of 92-104%, 95-102%, and 98-109% for spiked river water samples. These results indicated that the prepared DMAN@silica adsorbents could efficiently enrich PFSs and that the proposed method is reliable.