微量吸附量热研究CuO/γ-Al2O3催化剂的表面酸碱性质

The γ-Al₂O₃ supported CuO samples were studied. XRD results showed that the loading and calcination temperature affected the surface structure. For example， CuO crystallite appeared at the CuO loading of 7% (about 0.82mmol/100m²) on the support. Both CuO crystallite and CuAl₂O₄ spinel were present when the CuO/γ-Al₂O₃ sample was calcined at the same temperature (400℃). Microcalorimetric adsorption of CO₂ and NH₃ revealed that the strength of both the acidity and basicity decreased with the increase of CuO loading for the CuO/γ-Al₂O₃ sample. The increase of calcination temperature further decreased the basicity while the acidity was not affected.     

溶剂化金属原子浸渍法制备Pd-Cu/γ-Al2O3低温CO氧化催化剂

Nano-particle Pd/γ-Al₂O₃ monometallic and Pd-Cu/γ-Al₂O₃ bimetallic catalysts were prepared by solvated metal atom impregnation (SMAI) method. The results of XRD measurement indicated that Pd- Cu alloy was formed in the bimetallic catalysts and the crystalline particle size of the alloy increased as Cu contents increased with av-erage diameters < 6.0nm for all the samples. XPS and Auger spectra showed that Pd was in zero- valent state, Cu existed mainly in zero- valent state and partially in monovalent state Cu⁺. The Pd/γ-Al₂O₃ and Pd-Cu/γ-Al₂O₃ catalysts exhibited higher activity for CO oxidation at low temperature. The activity of Pd-Cu/γ-Al₂O₃ bimetallic catalyst was higher than that of Pd/γ-Al₂O₃ monometallic catalyst. The Pd-Cu/γ-Al₂O₃ catalyst with Pd/Cu atomic ratio of 1∶1 showed the highest activity.     

电镀烧结法制备Ti/SnO2-Sb2O4电极的研究

The Ti/SnO₂-Sb₂O₄ electrode has been prepared by the electroplate-sinter method. The effect of SbCl₃ adding amount and sintering temperature on its electrode lifetime and oxygen evolution potential were investigated by means of EDX, SEM and XRD analysis. The results indicated that the electrode appeared the best performance when the SbCl₃ adding amounts was 0.2g and the sintering temperature was 550℃. In optimized conditions Ti substrate was entirely covered by SnO₂-Sb₂O₄ and the combinations among them were tight. Due to the use of electroplate method, the electrical conductivity, the oxygen evolution potential and the electrode lifetime were increased, so the elec-tro-catalytic activity and the electrochemical stability of the prepared electrode were found to be superior.     

纳米尖晶石LixMn2O4的制备与电化学性能表征

Nano-spinel Li_xMn₂O₄(0.6 ≤x≤ 1.0) was synthesized by two steps of coprecipitation and calcination. The influences of calcination temperature, time and Li/Mn ratio on the crystal structure and the particle size of Li_xMn₂O₄ were investigated. It was shown that the higher the calcination temperature, the more complete the crystal structure, and the larger the particle size. Moreover, the influence of calcination time on the crystal structure was insignificant when it was more than 3h at 700℃. With the increase of x in Li_xMn₂O₄ in the range of 0.6～1.0, the d111 and lattice parameter a increased first and then decreased. The electrochemical properties of nano-spinel LiMn₂O₄ using as cathode material of lithium-ion battery were studied. The low discharge capacity might be due to the irreversible capacity loss brought by the large surface area and lattice vacancies of the nano-spinel.     

γ-Al2O3表面原位合成Ni-Al-CO3LDHs研究

Ni-Al-CO₃LDHs/γ-Al₂O₃have been prepared using an in-situ synthesis technique. NH₃·H₂O was chosen as activation agent of Al on the γ-Al₂O₃surface as well as precipitant. Ni-Al-CO₃LDHs/γ-Al₂O₃was synthesized by controlling the reaction conditions such as temperature, concentration of Ni²⁺ and initial pH. The crystalline structure, chemical composition and porous structure were characterized by means of XRD, FT-IR, TG-DTA, ²⁷Al MAS-NMR and N₂ adsorption-desorption. The resulting sample of Ni-Al-CO₃LDHs/γ-Al₂O₃possesses higher specific area and narrower pore distribution, in which Ni-Al-CO₃LDHs are located on the surface of γ-Al₂O₃and share the same Al-O bonds with the γ-Al₂O₃lattice. Finally a possible structural model was proposed to account for the porous characters of Ni-Al-CO₃LDHs/γ-Al₂O₃.     

Nd2O3添加量对BaTiO3陶瓷介电性能的影响

BaTiO₃ ceramics doped with Nd₂O₃(the additive content was respectively 0.001,0.002,0.003,0.005,0.01,0.03mol)were prepared by Sol-Gel method. Effects of Nd₂O₃ contents on the dielectric constant (ε), the dielectric loss (tanδ) ,the Curie-temperature (T_C) and the resistivity (ρ) of BaTiO₃ ceramic were studied. When Nd₂O₃ content was 0.001mol and 0.002mol, the dielectric constant was increased obviously, but the dielectric loss was also increased. When Nd₂O₃ content was 0.003mol, the dielectric constant was increased, and the dielectric loss was decreased, which was suitable for application in condenser. The resistivity was decreased obviously with the increasing of Nd₂O₃ contents, the resistivity was the smallest when Nd₂O₃ content was 0.001mol. The Curie-temperature was also decreased with the increasing of Nd₂O₃ contents.     

Ceramic Filter Balls Loaded with α-Fe2O3 and Their Application to NH3-N Wastewater Treatment

Hydrolysis reaction of Fe(NO₃)₃ at a high temperature in the presence of urea as the homogeneous precipitant was studied. With the prepared ceramic filter balls loaded with α-Fe₂O₃ after high temperature calcination, the loading of α-Fe₂O₃ on the porous ceramic filter balls from Fe(NO₃)₃ solutions of different concentrations and mechanical stability of the loaded α-Fe₂O₃ were studied. The product was characterized using XRD and SEM. Adsorption experiments were conducted to evaluate the performance of the product in adsorbing NH₃-N. It turned out that the specific surface area of the ceramic filter balls loaded with α-Fe₂O₃ had increased to 36.5387 m²/g from original 4.6127 m²/g. When the concentration of Fe(NO₃)₃ was 0.40 mol/L, the loading of α-Fe₂O₃ on the ceramic filter balls accounted for 8.4% of the total mass of the adsorbent and α-Fe₂O₃ was adsorbed on the filter balls very well. The adsorption isotherm of NH₃-N on the ceramic filter ball adsorbent loaded with α-Fe₂O₃ was of Langmuir type. The saturated adsorption capacity was 3.33 mg/L, and the adsorption constant K was 0.1873. NH₃-N was adsorbed by α-Fe₂O₃ more easily, which was a kind of specific adsorption.     

Cu-Ni/La2O3热解C2H2制备碳纳米管的研究

Nano-sized and well-dispersed Cu-Ni/La₂O₃ can be obtained by reduction of LaCu_0.2Ni_0.8O₃ with the structure of perovskite. Using Cu-Ni/La₂O₃ as catalyst and C₂H₂ as carbon source, carbon nanotubes with a high yield and narrow diameter distribution can be obtained in the reaction temperature range of 650～700℃. Outer diameter of carbon nanotubes rangs from 9nm to 14nm. TG, Raman and XPS analysis indicate that carbon nanotubes prepared by Cu-Ni/La₂O₃ are relatively higher in graphitic degree.     

ZrxTixAl1-2xO2的制备及其在三效催化剂上的应用

Zr_0.5Ti_0.5O₂(ZT) and Zr_0.25Ti_0.25Al_0.5O₂(ZTA) mixed oxides were prepared by co-precipitation method and characterized by low temperature adsorption-desorption， XRD and NH₃-TPD. The activity of Pt/Zr_0.5Ti_0.5O₂ and Pt/ Zr_0.5Ti_0.5Al_0.5O₂ catalysts was evaluated using the simulated gases. The results show that ZTA samples exhibit higher specific surface area， larger pore volume and proper surface acidic amount and acidity in comparison with ZT. The results of the catalytic test indicate that Pt/ZT and Pt/ZTA catalysts exhibit excellent low-temperature catalytic activity and lower light-off temperatures of hydrocarbon， carbon monoxide and nitrogen oxides， especially better conversion for nitrogen oxides (NO_x). The addition of Al₂O₃ into ZT enhanced the anti-aging property of Pt/ ZTA catalysts due to the excellent textural， structural， surface acidity and thermal stability.     

准球形α-Fe2O3的形成过程研究

The formation process of pseudo-spherical α-Fe₂O₃ particles obtained through the hydrolysis of 0.01 mol·L^-1 FeCl₃ solution was studied by means of TEM and XRD. The results show that the growth of α-Fe₂O₃ nuclies is through the diffusion mechanism. Although the presence of CTAB in the FeCl₃ solution has no effect on the growth process of pseudo-spheric α-Fe₂O₃ particles, more uniform particles are obtained, and the particles are self-assembled to form two-dimensional ordered structure due to the effect of CTAB. The optical character of these α-Fe₂O₃ particles was investigated, and the band-gap of which is about 2.49 eV.     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.