Cu/TiO_2和Cu/ZrO_2催化甲醇脱氢反应的对比研究(英文)

考察了ＴｉＯ_２和ＺｒＯ_２担载的铜基催化剂的结构及其催化甲醇脱氢的反应性能。氮吸附和ＥＸＡＦＳ结果显示,两个催化剂的结构性质以及铜所处的配位环境比较接近。但Ｘ-射线光电子能谱测试结果显示,催化剂Ｃｕ／ＴｉＯ_２中铜周围的电子密度较催化剂Ｃｕ／ＺｉＯ_２中的高。ＴｉＯ_２结果表明,ＴｉＯ_２能够降低与之接触的较大ＣｕＯ的还原温度。催化剂电子结构的不同导致反应性能的差异,在Ｃｕ／ＴｉＯ_２催化剂上甲酸甲酯是主要产物,而Ｃｕ／ＺｒＯ_２催化剂则催化甲醇深度脱氢生成ＣＯ。此外,Ｃｕ／ＺｒＯ_２催化剂失活较Ｃｕ／ＴｉＯ_２催化剂慢得多。     

在涂层TiO2改性铜催化剂上甲醇脱氢制甲酸甲酯

在常压和２５０℃下，考察了涂层ＴｉＯ２改性铜催化剂上甲醇脱氢生成甲酸甲酯的活性和选择性以及催化剂的稳定性。结果表明，涂层ＴｉＯ２明显提高了铜催化剂的活性和稳定性。在所考察的铜催化剂中，以Ｃｕ／ＴｉＯ２／ＡｌＯ３的催化活性最高，甚至高于离子交换法制备的Ｃｕ（ｅｘ）／ＳｉＯ２催化剂。ＸＰＳ分析表明，Ｃｕ／ＴｉＯ２／ＡｌＯ３中存在着两种化学环境不同的ＣＵ（０），即负载在ｒ－ＡＬＯ３和ＴｉＯ２－Ａｌ２Ｏ３     

甲烷部分氧化制合成气

对镍铜甲烷部分氧化催化剂的制备化学研究表明，在Ａｌ２Ｏ３、ＳｉＯ２、ｍｇＯ、ＴｉＯ２、Ｙ型分子筛等载体中，具有较好氢溢流功能的Ａｌ２Ｏ３所担载的镍铜催化剂，有最佳的反应性能、载体的产物溢物功能对反应中合成气的生成是有利的，对ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂，组分Ｃｕ的最佳含量是Ｃｕ／Ａｌ＝０．２／４（原子比），Ｎｉ／Ａｌ（原子比）在１／４－１．５／４范围内催化剂均保持最佳的反应性能，此时，甲烷转化     

甲烷部分氧化制合成气Ⅳ．镍铜催化剂的反应性能及影响因素的考察

对镍铜甲烷部分氧化催化剂的制备化学研究表明，在Ａｌ２Ｏ３、ＳｉＯ２、ＭｇＯ、ＴｉＯ２、Ｙ型分子筛等载体中，具有较好氢溢流功能的Ａｌ２Ｏ３所担载的镍铜催化剂，有最佳的反应性能，载体的产物溢流功能对反应中合成气的生成是有利的．对于ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂，组分Ｃｕ的最佳含量是Ｃｕ／Ａｌ＝０．２／４（原子比），Ｎｉ／Ａｌ（原子比）在１／４－１．５／４范围内催化剂均保持最佳的反应性能，此时，甲烷转化率为９８．１％，对ＣＯ、Ｈ２的选择性分别达９７％、１００％．制备方法对催化性能影响的结果显示，以（ＮＨ４）２ＣＯ３为沉淀剂的共沉淀法，是制备ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的最佳方法．ＮｉＯ－ＣｕＯ－Ａｌ２Ｏ３催化剂的甲烷部分氧化性能在４００－５００℃间有一突跃，并在７００℃时达到最佳值；过高的反应气空速对ＣＯ、Ｈ２的选择性是不利的     

单茂钛催化剂的丙烯无规聚合反应及其动力学研究

比较了不同钛化合物／甲基铝氧烷（ＭＡＯ）催化体系的丙烯无规聚合，催化活性次序为ＣｐＴｉ（ＯＲ）３＞ＣｐＴｉ（ＯＰｈ）３＞ＣｐＴｉＣｌ３＞Ｃｐ２ＴｉＣｌ２＞Ｔｉ（ＯＢｕ）４＞ＴｉＣｌ４＞Ｔｉ（ＯＢｕ）２Ｃｌ２，所得聚丙烯用沸庚烷抽提８ｈ，溶解９５％以上，可溶部分经１３Ｃ ＮＭＲ、ＷＡＤＸ、ＦＴＩＲ等分析证明为无规聚丙烯（ａＰＰ），是没有结晶性的弹性体．ＧＰＣ测出其分子量Ｍｗ＝８．０～１０．０×１０４，Ｍｗ／Ｍｎ≈２．０．探索了催化体系ＣｐＴｉ（Ｏ ｎ Ｐｒ）３／ＭＡＯ中钛的浓度、［Ａｌ］／［Ｔｉ］摩尔比，丙烯聚合压力，聚合温度和时间对丙烯聚合反应的影响．研究了该催化体系丙烯聚合反应动力学规律，表观聚合反应速率对催化剂浓度和单体压力（浓度）都呈一级反应关系，表观聚合速率常数ＫＰ＝２９２×１０５ｍｏｌ／Ｌ·ｈ（４０℃）．活化能ΔＥ＝－７．８８×１０３Ｊ·ｍｏｌ－１，碰撞因子Ａ＝１．４１×１０－４ｍｏｌ／Ｌ·ｈ．     

CuO／CeO_2／γ－Al_2O_3催化剂的结构及氧物种

应用ＸＲＤ、ＥＳＲ及ＸＰＳ方法研究了ＣｕＯ／ＣｅＯ２／γ－Ａｌ２Ｏ３催化剂的体相及表面结构，并对催化剂表面氧物种进行了表征．实验结果表明，ＣｅＯ２使Ｃｕ２＋还原为低价钢离子和增加钢化合物的分散性．催化剂中ＣｅＯ２含量高时，表面有Ｏ２－和Ｏ－物种，而ＣｅＯ２含量低时，只有Ｏ２－物种．     

乙醇一步法合成乙酸乙酯的Cu／ZnO／CoO／Al2O3／TiO2催化剂

乙醇一步法合成乙酸乙酯的Ｃｕ／ＺｎＯ／ＣｏＯ／Ａｌ２Ｏ３／ＴｉＯ２催化剂郑荣辉曾金龙（厦门大学化工系、物理化学研究所厦门３６１００５）关键词乙酸乙酯合成一步法双功能催化剂中图分类号Ｏ６２３．６２４．１乙醇为单一原料直接合成乙酸乙酯的新方法，克服了以浓...     

CuO－ZnO基CO_2／H_2合成甲醇催化剂的反应活性中心

应用ＸＰＳ，ＸＡＥＳ和紫外漫反射光谱法研究了ＣｕＯ－ＺｎＯ／氧化物上ＣＯ２／Ｈ２合成甲醇的反应活性中心．ＣｕＯ－ＺｎＯ／氧化物催化剂上的反应活性中心是存在于ＣｕＯ－ＺｎＯ固溶体中的Ｃｕ－Ｚｎ－Ｏ（＂□＂为氧空位），活性中心的Ｃｕ价态为Ｃｕ－和Ｃｕ０．反应活性中心在ＣｕＯＺｎＯ－ＺｒＯ２催化剂上比在其它ＣｕＯ－ＺｎＯ／氧化物催化剂如ＣｕＯ－ＺｎＯ，ＣｕＯ－ＺｎＯ－ＭｇＯ，ＣｕＯＺｎＯ－Ａｌ２Ｏ３和ＣｕＯ－ＺｎＯ－ｒ２Ｏ３上更加稳定．     

CuO／CeO2和CuO／Al2O3催化剂的催化性能

本文以ＣＯ氧化为模式反应考察了ＣｅＯ２和Ａｌ２Ｏ３负载氧化铜催化剂的氧化活性，运用ＸＲＤ和ＴＰＲ技术研究了催化剂的还原性能和物相结构，结果表明：载体性质对负载ＣｕＯ催化剂的ＣＯ氧化活性有很大影响，ＣｕＯ／ＣｅＯ２催化剂活性明显高于ＣｕＯ／Ａｌ２Ｏ３催化剂．催化剂的还原特性随载体不同而不同．同时发现，热处理对催化剂铜物种的存在形式，晶粒大小、还原特性及其催化活性有明显影响，ＣｕＯ／Ａｌ２Ｏ３催化剂活性下降的主要因素是生成了活性较低的ＣｕＡｌ２Ｏ４相，而ＣｕＯ／ＣｅＯ２催化剂活性下降是由于ＣｕＯ和ＣｅＯ２发生烧结，晶粒变大     

具有不同类型桥基的双核Cu(Ⅱ)-Schiff碱配合物的合成和晶体结构

合成了３个分别以Ｃ２Ｏ２－４（［Ｃｕ２（Ｌ１）２（ｏｘ）］，１），ＡｃＯ－（［Ｃｕ２（ＡｃＯ）（Ｌ２）２］ＢＦ４，２）和酚氧（［Ｃｕ２（Ｌ３）２］（ＣｌＯ４）２，３）为桥基的双核铜配合物，并测定了１的复配合物［Ｃｕ２（Ｌ１）２（ｏｘ）］·［Ｆｅ（ＯＨ）２（Ｈ２Ｏ）４］ＣｌＯ４·Ｈ２Ｏ（１′）及２和３的晶体结构．Ｘ射线衍射结果表明：１′，２和３分别属于Ｆｄｄｄ，Ｐ２１／ｃ和Ｐ２１／ｃ空间群．晶胞参数：［Ｃｕ２（Ｌ１）２（ｏｘ）］［Ｆｅ（ＯＨ）２（Ｈ２Ｏ）４］ＣｌＯ４·Ｈ２Ｏ，ａ＝２．４３９０（４）ｎｍ，ｂ＝３．０５３８（６）ｎｍ，ｃ＝１．８４９４（６）ｎｍ，α＝β＝γ＝９０．００°；２，ａ＝０．８４７（１）ｎｍ，ｂ＝２．６５４２（８）ｎｍ，ｃ＝１．４１００（６）ｎｍ，β＝９１．３４（６）°；３，ａ＝０．７６４６（３）ｎｍ，ｂ＝１．６９８３（３）ｎｍ，ｃ＝２．４４１７（３）ｎｍ，β＝９７．１１°     

α-Amino acid derived enaminones and their application in the synthesis of N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates and other heterocycles

A new and simple synthesis of novel N-protected methyl 5-substituted-4-hydroxypyrrole-3-carboxylates, which exist in equilibrium with their 4-oxo tautomers, has been developed in two steps starting from N-protected α-amino acids. The key intermediates are enaminones, which can also be isolated, characterized, and used for the construction of other functionalized heterocycles, before they spontaneously decompose to pyrrole products. 4-Hydroxypyrroles are prone to partial aerial oxidation but can be efficiently alkylated or reduced to stable polysubstituted pyrrolidine derivatives.     

Specific intramolecular aromatic CH insertion of diazosulfonamides

The chemoselectivity in the intramolecular CH insertion of various diazosulfonamides has been experimentally studied. The results reveal that the aliphatic 1,4-, 1,5-, or 1,6-C(sp³)?H insertions of diazosulfonamides are not accessible, while the aromatic 1,5-C(sp²)?H insertion can be realized specifically by adjusting the diazo-adjacent group. In addition, the general chemoselectivities in the intramolecular CH insertions of diazosulfonyl compounds are summarized. Generally, diazosulfones undergo both aromatic 1,5-C(sp²)?H and aliphatic 1,5- and 1,6-C(sp³)?H insertions, while diazosulfonates undergo aliphatic 1,5- and 1,6-C(sp³)?H insertions. However, diazosulfonamides only undergo aromatic 1,5-C(sp²)?H insertion.     

N-Heterocyclic carbene-palladacyclic complexes: synthesis,characterization and their applications in the C-N coupling and α-arylation of ketones using aryl chlorides

N-Heterocyclic carbene-palladacyclic complexes 3 were successfully achieved in a one-pot procedure under mild conditions. The structure of 3a was unambiguously confirmed by X-ray single crystal diffraction and it was an active catalyst in the Buchwald-Hartwig amination and α-arylation of ketones even at very low catalyst loadings (0.01?mol%).     

Iodine-mediated oxidative Pictet-Spengler reaction using terminal alkyne as the 2-oxoaldehyde surrogate for the synthesis of 1-aroyl-β-carbolines and fused-nitrogen heterocycles

An efficient iodine-mediated oxidative Pictet-Spengler reaction in dimethyl sulphoxide (DMSO) using terminal alkynes as the 2-oxoaldehyde surrogate for the synthesis of aryl (9H-pyrido[3,4-b]indol-1-yl)methanones is described. The scope of the protocol includes the total synthesis of Fascaplysin, Eudistomins Y₁ and Y₂. The methodology is extended for preparing pyrrolo[1,2-a]-quinoxaline and indolo[1,5-a]quinoxaline derivatives. The utility of 1-aroyl-β-carbolines was demonstrated by performing palladium-catalyzed β-carboline directed ortho-C(sp2)-H functionalization of the phenyl ring with thiomethyl (SMe) group using DMSO as source and for accessing 4-aryl-canthin-6-ones.     

Facile synthesis of bicyclic 1-arylpyrazol-5-ones

In this Letter, we described a facile method for constructing fused bicyclic 1-arylpyrazol-5-one ring system. We employed various methylene-containing carboxylic acids as the substrates and proved that the pyrazolone ring closure requires activated methylene group in intermediate II. Accordingly, a series of structurally diversified, fused bicyclic 1-arylpyrazol-5-ones was prepared in moderate to high yields using the requisite substrates.     

Synthesis of pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles by Curtius reaction in Morita-Baylis-Hillman derivatives

Synthesis of substituted pyrrolo[1,2-a]pyrazines and pyrazino[1,2-a]indoles from the Morita-Baylis-Hillman derivatives of acrylates via saponification followed by Curtius reaction is described.     

Cu0-catalysed 1,3-dipolar cycloadditions of α-amino acid derived N,N-cyclic azomethine imines to ynones

A series of 20 CuAIAC reactions between eight 4-acylamino substituted pyrazolidine-3-one-1-azomethine imines and four terminal ynones were performed using Cu⁰ as catalyst. The corresponding fluorescent cycloadducts were obtained in very high yields upon simple workup. Thus, Cu-metal turned out to be a better catalyst than Cu^I in terms of yield and ease of isolation. Availability of azomethine imines, mild reaction conditions, and simple workup enable a “click” access to libraries of densely substituted 2,3-dihydro-1H,5H-pyrazolo[1,2-a]pyrazol-1-ones. Reactivity of differently substituted dipoles was evaluated experimentally and by quantum chemical methods (DFT).     

Synthesis and antioxidative/anti-inflammatory activity of novel fullerene–polyamine conjugates

(E)-4-(Fullerenopyrrolidin-1-yl)-3-methylbut-2-enoic acid and its corresponding succinimidyl ester, readily obtained through Prato-type modification of C₆₀, were used for the selective N-acylation of polyamines. The thus obtained conjugates were evaluated for their antioxidative and anti-inflammatory activity and their cytotoxicity was determined. Members of this family of compounds showed interesting anti-lipid peroxidation, anti-lipoxygenase and anti-inflammatory activity and comparable cytocompatibility to spermidine.     

Copper-catalyzed multicomponent reactions of 2-iodoanilines,benzylamines, and elemental sulfur toward 2-arylbenzothiazoles

A relatively cheap copper salt-catalyzed, three-component approach providing 2-arylbenzothiazoles in good to excellent yields from readily available 2-iodoanilines, benzylamines, and sulfur powder is reported. This methodology allows preparation of various classes of 2-arylbenzothiazoles and provides a general, reliable approach.