Coatings with thermally switchable surface energy produced from poly(ethylene oxide)-poly(dimethylsiloxane) block copolymer films

This work explores coatings with thermally switchable wetting behavior, based on block copolymers that possess both hydrophilic and hydrophobic segments. The amphiphilic block copolymers were synthesized by coupling allyl-ended poly(ethylene oxide) (PEO) and hydride-ended poly(dimethylsiloxane) (PDMS) oligomers via a Pt catalyst. One near-symmetric diblock possessed an order-disorder transition temperature (T_ODT) of 64 °C. When cooled through T_ODT in ambient air, the PDMS domains wet the film's surface, producing a hydrophobic coating with a water contact angle (CA) = 90°. However, when cooled in humidified air, hydrophilic PEO domains form at the surface, yielding CA = 30–40°. The coatings can be reversibly switched between the two states by reheating above T_ODT, in the appropriate environment, and then cooling, rapidly generating the desired room-temperature surface wettability. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016, 54, 135–140     

High‐performance thin film composite membranes with well‐defined poly(dimethylsiloxane)‐b‐poly(ethylene glycol) copolymer additives for CO2 separation

A series of well‐defined diblock copolymers (BCPs) consisting of poly(ethylene glycol) (PEG) and poly(dimethylsiloxane) (PDMS) were synthesized and blended with commercially available PEBAX® 2533 to form the active layer of thin‐film composite (TFC) membranes, via spin‐coating. BCPs with a PEG component ranging from 1 to 10 kDa and a PDMS component ranging from 1 to 10 kDa were synthesized by a facile condensation reaction of hydroxyl terminated PEG and carboxylic acid functionalized PDMS. The BCP/PEBAX® 2533 blends up to 50 wt % on cross‐linked PDMS gutter layers were tested at 35 °C and 350 kPa. TFC membranes containing BCPs of 1 kDa PEG and 1–5 kDa PDMS produced optimal results with CO₂ permeances of approximately 1000 GPU which is an increase up to 250% of the permeance of pure PEBAX® 2533 composite membranes, while maintaining a CO₂/N₂ selectivity of 21. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 1500–1511     

Breathable rubbery skin protectors: Design,synthesis, characterization,and properties of cyanoacrylated silicone rubber networks

We extended our investigations of rubbery wound closure adhesives and created novel flexible networks by crosslinking cyanoacrylated silicone rubbers (i.e., commercial methylhydrosiloxane‐dimethylsiloxane copolymers, PMHS‐co‐PDMS) with N,N‐dimethyl‐p‐toluidine in tetrahydrofuran and hexamethyldisiloxane solvents at room temperature. Cyanoacrylation was achieved by hydrosilating (anthracene‐protected) allyl cyanoacrylate with PMHS‐co‐PDMS. Steric hindrance and the molecular weight of the copolymer strongly affect the extent of hydrosilation. The rate of crosslinking is proportional with the number of cyanoacrylate groups in the copolymer and networks form in seconds with appropriate amounts of initiator. Networks on porcine skin yield well‐adhering flexible optically‐transparent colorless conformal coatings of good “feel” appropriate for clinically useful non‐occlusive “breathable” skin or wound protectors. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2016 , 54, 1367‐1372     

Synthesis and characterization of model polybutadiene‐1,4‐b‐polydimethylsiloxane‐b‐polybutadiene‐1,4 copolymers

Model copolymers of poly(butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS‐b‐PB, were synthesized by sequential anionic polymerization (high vacuum techniques) of 1,3‐butadiene and hexamethylciclotrisiloxane (D₃) on sec‐BuLi followed by chlorosilane‐coupling chemistry. The synthesized copolymers were characterized by nuclear magnetic resonance (¹H NMR), size‐exclusion chromatography (SEC), thermogravimetric analysis (TGA), and differential scanning calorimetry (DSC). SEC and ¹H NMR results showed low polydispersity indexes (M_w/M_n) and variable siloxane compositions, whereas DSC and TGA experiments indicated that the thermal stability of the triblock copolymers depends on the PDMS composition. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 2726–2733, 2007     

Temperature‐dependent phase‐segregation behavior and antifouling performance of UV‐curable methacrylated PDMS/PEG coatings

Controllable phase segregation adjustment for immiscible polymer blends has always been tough, which hinders the development of amphiphilic antifouling coatings from more accessible blends. Herein, methacrylated poly(dimethylsiloxane) (PDMS‐MA) was synthesized and mixed with poly(ethylene glycol)methylether methacrylate (PEG‐MA). It was interestingly discovered that these PDMS‐MA/PEG‐MA blends displayed upper critical solution temperatures (UCST) due to thermo‐induced conformational change of PEG‐MA and the UCST changed with PDMS‐MA/PEG‐MA mass ratios. Micro‐/nano‐phase segregation, nanophase segregation, or homogenous morphology were therefore achieved. These PDMS‐MA/PEG‐MA blends with different mass ratios were UV‐cured under varying temperatures to fabricate coatings. Their surface morphology and wettability are readily adjusted by phase segregation. For the first time, highly hydrophilic surface was achieved for coatings with microphase segregation because of the exposure of PEG‐rich domains, which exhibited an enhanced protein resistance against bovine serum albumin (BSA). Anti‐bacterial performance (Shewanella loihica) was also observed for these PDMS/PEG coatings. © 2016 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2016 , 54, 1612–1623     

Synthesis and morphology of model PS‐b‐PDMS copolymers

True model linear poly(styrene‐b‐dimethylsiloxane) PS‐b‐PDMS copolymers were synthesized by using sequential addition of monomers and anionic polymerization (high‐vacuum techniques), employing the most recent experimental procedures that allow the controlled polymerization of each monomer to obtain blocks with controlled molar masses. The model diblock copolymers obtained were analyzed by using different techniques, such as size‐exclusion chromatography, ¹H NMR, Fourier transform infrared spectroscopy, small angle X‐rays scattering (SAXS), and wide angle X‐rays scattering (WAXS). The PS‐b‐PDMS copolymers obtained showed narrow molar mass distribution and variable PDMS content, ranging from 2 up to 55 wt %. Compacted powder samples were investigated by SAXS to reveal their structure and morphology changes on thermal treatment in the interval from 30 to 200 °C. The sample with the highest PDMS content exhibits a lamellar morphology, whereas two other samples show hexagonally packed cylinders of PDMS in a PS matrix. For the lowest PDMS content samples, the SAXS pattern corresponds to a disordered morphology and did not show any changes on thermal treatment. Detailed information about the morphology of scattering domains was obtained by fitting the SAXS scattering curves. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 3119–3127, 2010     

Synthesis of polybutadiene‐graft‐poly(dimethylsiloxane) and polyethylene‐graft‐poly(dimethylsiloxane) copolymers with hydrosilylation reactions

We report preliminary results for the synthesis of polyethylene‐graft‐poly(dimethylsiloxane) copolymers obtained by catalytic hydrogenation of polybutadiene‐graft‐poly(dimethylsiloxane) copolymers (PB‐g‐PDMS). These last copolymers were synthesized by hydrosilylation reactions between commercial polybutadiene and ω‐silane poly(dimethylsiloxane). The reaction was carried in solution catalyzed by cis‐dichloro bis(diethylsufide) platinum(II) salt. The PB‐g‐PDMS copolymers were analyzed by ¹H and ¹³C NMR spectroscopies, and the relative weight percentages of the grafted poly(dimethylsiloxane) macromonomer were determined from the integrated peak areas of the spectra. © 2004 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 42: 2920–2930, 2004     

Synthesis and characterization of model diblock copolymers of poly(dimethylsiloxane) with poly(1,4‐butadiene) or poly(ethylene)

Model diblock copolymers of poly(1,4‐butadiene) (PB) and poly(dimethylsiloxane) (PDMS), PB‐b‐PDMS, were synthesized by the sequential anionic polymerization (high vacuum techniques) of butadiene and hexamethylciclotrisiloxane (D₃) in the presence of sec‐BuLi. By homogeneous hydrogenation of PB‐b‐PDMS, the corresponding poly(ethylene) and poly(dimethylsiloxane) block copolymers, PE‐b‐PDMS, were obtained. The synthesized block copolymers were characterized by nuclear magnetic resonance (¹H and ¹³C NMR), size‐exclusion chromatography (SEC), Fourier transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and rheology. SEC combined with ¹H NMR analysis indicates that the polydispersity index of the samples (M_w/M_n) is low, and that the chemical composition of the copolymers varies from low to medium PDMS content. According to DSC and TGA experiments, the thermal stability of these block copolymers depends on the PDMS content, whereas TEM analysis reveals ordered arrangements of the microphases. The morphologies observed vary from spherical and cylindrical to lamellar domains. This ordered state (even at high temperatures) was further confirmed by small‐amplitude oscillatory shear flow tests. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 1579–1590, 2006     

Well‐defined PE‐b‐PDMS diblock copolymers via the combination of thiol‐ene click and esterification reactions: Facile synthesis and compatibilization for HDPE/silicone oil blends

Well‐defined diblock copolymers of linear polyethylene (PE) and poly(dimethylsiloxane) (PDMS) have been synthesized through a facile route combining the thiol‐ene click chemistry of vinyl‐terminated polyethylene (PE‐ene) and the sequential esterification reaction. The resulting diblock copolymers are characterized by ¹H NMR, FT‐IR, DSC, TGA, and TEM. In addition, the PE‐b‐PDMS diblock copolymers have been evaluated as compatibilizers in the blends of high‐density polyethylene (HDPE) and silicone oil. The morphological analysis and mechanical properties demonstrate that the compatibilized blends with low loading concentration of PE‐b‐PDMS display significant improvements in modulus of elasticity and elongation at break as compared to the uncompatibilized binary blends. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3205–3212     

Nanopatterning and micropatterning of cobalt containing block copolymers via phase‐separation and lithographic techniques

Reversible addition fragmentation transfer (RAFT) agent functionalized polydimethylsiloxane (PDMS‐RAFT) was used as a macro‐RAFT agent to polymerize a mixed sandwich cobaltocene containing monomer featuring η⁵‐cyclopentadienyl‐cobalt‐η⁴‐cyclobutadiene. High molecular weight block copolymers (BCP) consisting of a metallic block and a PDMS block with excellent control over molecular weight and polydispersity were prepared. Solid‐state self‐assembly of this BCP resulted in hexagonal domains of metallopolymer phase‐separated from PDMS. In solution, spherical micelles with a metallic core, stabilized by a PDMS corona were prepared. Pyrolysis of the BCP resulted in magnetic nanoparticles with 30% char yield. The BCP was used as an ink material for microcontact printing (μCP) to transfer long‐ranged patterns. © 2015 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2015 , 53, 2747–2754     

Synthesis of poly(tert‐butyl methacrylate)‐graft‐poly(dimethylsiloxane) graft copolymers via reversible addition‐fragmentation chain transfer polymerization

Well‐defined poly(tert‐butyl methacrylate)‐graft‐poly (dimethylsiloxane) (PtBuMA‐g‐PDMS) graft copolymers were synthesized via reversible addition‐fragmentation chain transfer (RAFT) copolymerization of methacryloyl‐terminated poly (dimethylsiloxane) (PDMS‐MA) with tert‐butyl methacrylate (tBuMA) in ethyl acetate, using 2,2′‐azobis(isobutyronitrile) (AIBN) as the initiator and 2‐cyanoprop‐2‐yl dithiobenzoate as the RAFT agent. The RAFT statistical copolymerization of PDMS‐MA with tBuMA is shown to be azeotropic and the obtained PtBuMA‐g‐PDMS graft copolymers have homogeneously distributed branches because of the similar reactivity of monomers (r_tBuMA ≈ r_PDMS‐MA ≈ 1). By the RAFT block copolymerization of PDMS‐MA with tBuMA, moreover, narrow molecular weight distribution (M_w/M_n < 1.3) PtBuMA‐g‐PDMS graft copolymers with gradient or blocky branch spacing were synthesized. The graft copolymers exhibit the glass transitions corresponding to the PDMS and PtBuMA phase, respectively. However, the arrangement of monomer units in copolymer chains and the length of PtBuMA moieties have important effects on the thermal behavior of PtBuMA‐g‐PDMS graft copolymers. © 2011 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2011     

Synthesis and characterization of amphiphilic fluorinated pentablock copolymers based on Pluronic F127

The synthesis and self‐assembly behavior of pentablock copolymers consisting of Pluronic F127 (PEO₁₀₀‐PPO₆₅‐PEO₁₀₀) and poly(2, 2, 3, 3, 4, 4, 5, 5‐octafluoropentyl methacrylate) (POFPMA) is herein described. Using the difunctional potassium alcoholate of F127, K⁺O^–‐(PEO₁₀₀‐PPO₆₅‐PEO₁₀₀)‐O^–K⁺, as the macroinitiator, the POFPMA‐F127‐POFPMA pentablock copolymers were synthesized via oxyanion‐initiated polymerization. The chain length of POFPMA can be controlled by the original molar ratio of macroinitiator to OFPMA monomer, that is, F‐monomer. The composition and chemical structure of POFPMA‐F127‐POFPMA pentablock copolymers have been characterized by FTIR, ¹HNMR, and ¹⁹F NMR spectroscopy, and gel permeation chromatography techniques. The solution behavior of POFPMA‐F127‐POFPMA copolymers was investigated by the methods of surface tension, cloud point, transmission electron microscopy, and high performance particle sizer (HPPS). The results indicate that these Pluronic F127‐based block copolymers modified with fluorinated segments possess relatively high surface activity and low cloud points, depending on various factors, such as the length of fluorinated block, the concentration of the copolymers in aqueous solution, and the adscititious inorganic salt. TEM measurements showed that the pentablock copolymers can self‐assemble in aqueous solution to form various micellar morphologies. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 3029–3041, 2008     

Novel poly(l‐lactide)/poly(d‐lactide)/poly(tetrahydrofuran) multiblock copolymers with a controlled architecture: Synthesis and characterization

Novel poly(l ‐lactide) (PLLA)/poly(d ‐lactide) (PDLA)/poly(tetrahydrofuran) (PTHF) multiblock copolymers with designed molecular structure were synthesized by a two‐stage procedure. Well‐defined PDLA‐PLLA‐PTHF‐PLLA‐PDLA pentablock copolymers were prepared by sequential ring opening polymerization of l ‐ and d ‐lactides starting from PTHF glycol, with the length of the (equimolar) PLLA and PDLA blocks being varied. Then, these dihydroxyl‐terminated pentamers were transformed into multiblock copolymers by melt chain‐extension with hexamethylene diisocyanate–being the first time that the coupling of pentablock units is reported. The successful formation of macromolecular chains with a multiblock and well‐defined architecture was demonstrated by ¹H NMR spectroscopy. The thermal properties and structuring of the resulting materials were investigated by means of DSC and WAXD measurements and DMA analysis. Stereocomplexation was found to be promoted during solution and melt crystallization. This approach affords materials combining the high rigidity and strength (other than improved thermal resistance) of the hard stereocomplex crystallites with the flexibility imparted by the soft block, whereby their properties can be finely tailored through the composition of the basic pentablock units without limitations on the final molecular weight. The adopted reaction conditions make this process highly appealing in view of the possibility to perform it in extruder. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 3269–3282     

Hierarchically ordered ABA triblock copolymer with large difference in glass transition temperatures of the two blocks

Rod‐coil‐rod triblock copolymers, poly[4′‐(methoxy)‐2‐vinylbiphenyl‐4‐methyl ether] ‐blockpolydimethylsiloxane‐block‐poly[4′‐(methoxy)‐2‐vinylbiphenyl‐4‐methyl ether] (PMVBP‐b‐PDMS‐b‐PMVBP), were synthesized by nitroxide‐mediated radical polymerization, and their hierarchically ordered structures were studied. A difunctional TEMPO macroinitiator was first synthesized by the hydrosilylation reaction between hydride‐endcapped PDMS and allylic alkoxyamine. The polymerization of the monomer MVBP was triggered by the macroinitiator, resulting in a series of triblock copolymers. The molecular weights and polydispersity indexes were determined by gel permeation chromatography. Differential scanning calorimetry results demonstrate that the triblock copolymers exhibit two glass transition temperatures (?120 °C and 160 °C) that are markedly different. As revealed by small‐angle X‐ray scattering and transmission electron microscopy experiments, the triblock copolymers self‐assemble into hierarchical structures with the liquid crystalline phase of PMVBP in the lamellar structures. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1737–1744     

Synthesis,self‐assembly,and thermosensitivity of amphiphilic POEGMA‐PDMS‐POEGMA triblock copolymers

In this article, the synthesis and self‐assembly of a novel well‐defined biocompatible amphiphilic POEGMA‐PDMS‐POEGMA triblock copolymer were studied. The copolymer was synthesized by atom transfer radical polymerization of oligo(ethylene glycol) methyl ether methacrylate (OEGMA) using α,ω‐dibromo polydimethylsiloxane macroinitiator (Br‐PDMS‐Br). Br‐PDMS‐Br was synthesized through the esterification of α,ω‐hydroxypropyl polydimethylsiloxane and 2‐bromoisobutyryl bromide. The structures of the copolymers were confirmed by proton nuclear magnetic resonance spectroscopy, and gel permeation chromatography. The copolymers showed reversible aggregation in response to temperature cycles with a lower critical solution temperature (LCST) between 61 and 66 °C, as determined by ultraviolet‐visible spectrophotometry and dynamic light scattering. The LCST values increased in proportion to the length of the hydrophilic block and were lower than that of the POEGMA homopolymer. The self‐assembly behavior of the copolymers in aqueous solution was investigated by fluorescence spectroscopy and transmission electron microscopy. The critical micelle concentration value (1.08–0.26 10^?6 mol L^?1) decreased as the length of the POEGMA chain increased. The POEGMA‐PDMS‐POEGMA copolymers can easily self‐assemble into spherical micelles in aqueous solution. Such biocompatible block copolymers may be attractive candidates as ‘‘smart'' thermo‐responsive drug delivery systems. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 2684‐2691     

High‐molecular‐weight symmetrical multiblock copolymers: Synthesis by RAFT polymerization and characterization

High‐molecular‐weight (MW) symmetrical multiblock copolymers, based on the hydrophobic monomers styrene (Sty) and methyl methacrylate (MMA), and the more polar monomer, 2‐vinyl pyridine (2VPy), were prepared using stepwise reversible addition‐fragmentation chain transfer polymerization. All copolymers shared a common poly(ethylene glycol) (PEG) midblock, introduced as a bifunctional macromolecular chain transfer agent. In total, five ABA triblock copolymers, five ABCBA pentablock terpolymers, and two ABCDCBA heptablock quaterpolymers (comprising four different monomer types) were synthesized. The MWs of the multiblock polymers were determined using gel permeation chromatography (GPC) and proton nuclear magnetic resonance (¹H NMR) spectroscopy, with the latter values being closer to the theoretically expected, whereas GPC MW distributions were relatively narrow, broadening with the number of blocks. The compositions of the synthesized polymers, as determined by ¹H NMR spectroscopy, were also close to the expected values. Finally, films cast from chloroform solutions of the pentablock terpolymers P2VPy‐b‐PSty‐b‐PEG‐b‐PSty‐b‐P2VPy, PSty‐b‐PMMA‐b‐PEG‐b‐PMMA‐b‐PSty, and P2VPy‐b‐PMMA‐b‐PEG‐b‐PMMA‐b‐P2VPy examined using transmission electron microscopy exhibited PSty and PMMA cylinders (first two) and lamellae (third terpolymer). © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2013 , 51, 4957–4965     

Ion‐Exchange‐Induced 2D–3D Conversion of HMA1−xFAxPbI3Cl Perovskite into a High‐Quality MA1−xFAxPbI3 Perovskite

High‐quality phase‐pure MA_1?xFA_xPbI₃ planar films (MA=methylammonium, FA=formamidinium) with extended absorption and enhanced thermal stability are difficult to deposit by regular simple solution chemistry approaches owing to crystallization competition between the easy‐to‐crystallize but unwanted δ‐FAPbI₃/MAPbI₃ and FA_xMA_1?xPbI₃ requiring rigid crystallization conditions. Here A 2D–3D conversion to transform compact 2D mixed composition HMA_1?xFA_xPbI₃Cl perovskite precursor films into 3D MA_1?xFA_xPbI₃ (x=0.1–0.9) perovskites is presented. The designed Cl/I and H/FA(MA) ion exchange reaction induced fast transformation of compact 2D perovskite film, helping to form the phase‐pure and high quality MA_1?xFA_xPbI₃ without δ‐FAPbI₃ and MAPbI₃ impurity. In all, we successfully developed a facile one‐step method to fabricate high quality phase‐pure MA_1?xFA_xPbI₃ (x=0.1–0.9) perovskite films by 2D–3D conversion of HMA_1?xFA_xPbI₃Cl perovskite. This 2D–3D conversion is a promising strategy for lead halide perovskite fabrication.     

Poly(N‐vinylpyrrolidone)–polydimethylsiloxane amphiphilic ABA triblock copolymers

Triblock copolymers of N‐vinylpyrrolidone (NVP) and polydimethylsiloxane (PDMS) were synthesized by reversible addition‐fragmentation chain transfer (RAFT) polymerization using two different types of difunctional telechelic PDMS‐based dixanthate macroinitiators. The incorporation of PDMS into the triblock copolymers was evidenced by ¹H NMR spectroscopy and varied between 4 mol % and as high as 20 mol %, dependent on reaction time and monomer conversion. The copolymer homogeneity was characterized in terms of molecular weight distribution determined by GPC to estimate the level of control over the chain length. Monomodal molecular weight distributions were observed, and ¹H NMR spectroscopy indicated the copolymers had number average molecular weights (M_n) ranging between 28,000 and 160,000 g/mol. In addition, thin film phase separation and critical micelle concentrations for these copolymers were analyzed via transmission electron microscopy and surface tension measurements, respectively. © 2017 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2017 , 55, 3387–3394     

Soft nanoparticles assembled from linear poly(ethylene glycol) and linear brush polydimethylsiloxane diblock copolymers

A series of novel amphiphilic diblock copolymers composed of hydrophilic linear poly(ethylene glycol) (PEG) and linear brush hydrophobic polydimethylsiloxane (PDMS) were synthesized. Three different molecular weights of monomethyl ether PEG were initially functionalized with 2‐bromoisobutyryl bromide to afford macroinitiators suitable for atom‐transfer radical polymerization. The macroinitiators were characterized by gel permeation chromatography, ¹H and ¹³C nuclear magnetic resonance spectroscopic analysis and matrix‐assisted laser desorption ionization time‐of‐flight mass spectroscopy. The three different molecular weight macroinitiators were then chain extended with monomethacryloxypropyl‐terminated PDMS and photoactive 2‐(methylacyloyloxy)ethyl anthracene‐9‐carboxylate in different molar ratios to afford a series of photoresponsive amphiphilic diblock copolymers with high conversions. Self‐assembly of these linear–linear brush diblock copolymers in N,N‐dimethylformamide afforded nanoparticles with hydrodynamic diameters (d_H) ranging from 41 to 268 nm, as determined by dynamic light scattering analysis. Crosslinking and stabilization of the nanoparticles was achieved via [4+4] photodimerization of the anthracene moieties upon exposure to UV radiation at 365 nm with the reverse reaction studied at a wavelength of 254 nm. Transmission electron microscopy revealed that the self‐assembled nanoparticles and their crosslinked derivatives had spherical morphologies. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2014 , 52, 1251–1262     

Synthesis,characterization, and crosslinking of methacrylate‐telechelic PDMAAm‐b‐PDMS‐b‐PDMAAm copolymers

The synthesis and molecular characterization of a new amphiphilic conetwork (APCN) designed for silicone hydrogel use is described. The synthesis strategy, outlined in Scheme 1 , calls for the preparation, by the RAFT technique, of a new methacrylate‐telechelic amphiphilic pentablock, MA‐PHEA‐b‐PDMAAM‐b‐PDMS‐b‐PDMAAm‐b‐PHEA‐MA, and its crosslinking to the target APCN. The sketch shows the architecture of the APCN (dotted lines, PDMAAm; solid lines, PDMS; clusters, MA‐based crosslinking sites; see Fig. 3 ). All six synthesis steps proceed smoothly and efficiently, and the products are optically clear, colorless membranes exhibiting properties appropriate for ophthalmic use. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 4284–4290, 2007