首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 171 毫秒
1.
核/壳型聚硅氧烷丙烯酸酯复合乳液的制备   总被引:40,自引:0,他引:40  
范青华  黄英 《应用化学》1995,12(3):52-56
采用种子乳液聚合的方法制备了具有核/壳结构的聚硅氧烷丙烯酸酯复合乳液,考察了乳化剂、单体的加入方式及配比对产生乳液粒子的影响。结果表明,乳化剂在核阶段和壳阶段的单体聚合中都起着很重要的作用,当乳化剂分子在乳液粒子上的覆盖率低于40%时,可制得较理想的核/壳型复合乳液。  相似文献   

2.
有机硅-丙烯酸酯聚合物乳液合成及粒径分析   总被引:4,自引:1,他引:3  
通过种子乳液半连续法合成了有机硅改性丙烯酸酯聚合物乳液,并对其粒子形态及分布进行分析。结果表明:通过种子乳液半连续聚合工艺可制备出固含量42wt%,乳化剂含量4wt%(基于单体量)、窄分布纳米粒子的有机硅改性丙烯酸酯聚合物乳液。随反应进行,粒径分布变窄,平均粒径逐渐增大。随乳化剂中SDS与OP-10的摩尔比减少,粒径增大。  相似文献   

3.
研究了半连续和间歇式丙烯酸酯三元乳液共聚产物的形态和分子结构。结果表明,半连续式胶乳粒子呈“多核核壳结构”,其粒径和粒径分布随单体滴加速度减慢而变小。间歇式胶乳粒径较大,粒径分布亦更宽,呈硬相在外的“单核核壳结构”;共聚物分子链中VAc结构单元的序列较长。两种方法所获无规共聚物均存在微相分离结构,分离程度随单体滴加速度的加快而变大。  相似文献   

4.
以十二烷基硫酸钠(SDS)为乳化剂,采用多步种子乳液聚合方法制备了核/壳结构乳液,研究了乳化剂加入量以及加料速率对核壳乳液聚合的影响,并推导了核及壳乳液聚合阶段所需乳化剂量的计算公式.研究表明,当种子、核、壳乳液聚合阶段单体量分别为12g、50g和50g,种子乳液聚合阶段加入的乳化剂量为0.44g时,控制核、壳乳液聚合阶段乳化剂的加入量分别在0.64~2.07g及0.04~2.12g之间,且预乳化单体的滴加速度低于2.3g/min时,可以防止二次成核及新乳胶粒子的形成,制得粒径分布窄、核/壳结构明显的乳胶粒子.利用透射电镜(TEM)对所制备的核壳结构乳胶粒子的结构形态进行了验证,试验结果与理论预测结果一致.  相似文献   

5.
用核/壳乳液聚合工艺,通过改变单体组成、设计乳胶粒子的形态结构和在乳胶粒子的壳层中引入含氟丙烯酸酯单体,制备具有核/壳结构的含氟丙烯酸酯的共聚乳液。并通过FTIR1、3C-NMR、TEM等手段对共聚乳液的化学结构以及乳胶粒子形态结构进行了表征。同时研究了含氟单体种类和用量、乳化剂种类以及单体加料方式对其聚乳液性能以及浸渍滤纸抗水/油性的影响。  相似文献   

6.
核壳型聚丙烯酸酯乳胶粒子及其乳液的研究进展   总被引:1,自引:0,他引:1  
综述了目前制备核壳型聚丙烯酸酯乳胶粒子的常用方法,如种子乳液聚合法、无皂乳液聚合法、反相乳液聚合法、细乳液聚合法以及种子分散聚合法;分析了聚合工艺、单体种类、温度、乳化剂和引发剂种类及用量等因素对聚丙烯酸酯核壳乳液合成及性能的影响;并对聚丙烯酸酯核壳乳液的研究现状进行了归纳;最后,展望了聚丙烯酸酯核壳乳液的发展方向。  相似文献   

7.
以乳化剂十二烷基硫酸钠 (SDS)和共乳化剂十六烷醇 (HD)作为复合乳化体系 ,过氧化二苯甲酰(BPO)和N ,N 二甲基苯胺 (DMA)作为氧化还原引发体系 ,甲基丙烯酸甲酯 丙烯酸丁酯 (MMA BA)作为混合单体 ,制备了分散相占 83 %以上的稳定的超浓乳液 ,然后在低温下引发聚合 .探讨了引发剂浓度、氧化剂与还原剂的摩尔比、乳化剂的浓度、液膜增强剂的种类、聚合温度等因素对聚合稳定性和聚合速率的影响 ,测定并计算得到了聚合速率的公式 ;用激光散射粒度分布仪测定了聚合物乳胶粒子的大小及粒径分布 ,用透射电子显微镜观察了聚合物乳胶粒的形态 ,讨论了乳化剂浓度、聚合温度等对乳胶粒形态、大小的影响  相似文献   

8.
张凯  黄春保  沈慧芳  陈焕钦 《应用化学》2012,29(10):1111-1116
以氯丁胶乳(Pa)为种子乳液,甲基丙烯酸甲酯(Pb)为第二单体,采用种子乳液聚合法,制备了氯丁胶乳-聚甲基丙烯酸甲酯复合乳胶粒。热力学分析表明,当Pb的体积分数Φb<0.69时,可同时形成Pa-Pb型正核-壳和(Pa+Pb)分离型乳胶粒,当Φb>0.69时,形成Pb-Pa型翻转型核壳结构乳胶粒,并伴有Pa-Pb型正核-壳结构乳胶粒的形成。动力学分析表明,引发剂类型、第二单体的加入方式、种子乳胶粒的交联、单体/聚合物质量比是影响乳胶粒形态的主要因素。采用水溶性引发剂过二硫酸钾(KPS),以饥饿态方式加入单体,氯丁胶乳-聚甲基丙烯酸甲酯(PCR-PMMA)复合乳胶粒呈现正核-壳结构,以充溢态方式加入单体则不能形成明显的核-壳结构;而以油溶性偶氮二异丁腈(AIBN)为引发剂时,单体无论以充溢态方式加入还是饥饿态加入均倾向于形成翻转核-壳型粒子。在种子乳胶粒中加入一定量交联剂二缩三乙二醇二甲基丙烯酸酯,有利于形成明显的正核壳结构。以饥饿态进料,KPS为引发剂时,随着单体用量增加,壳层变厚,仍呈正核-壳结构,与热力学分析结果相吻合;以AIBN为引发剂时,随着单体用量增加,PCR-PMMA复合乳胶粒逐渐由翻转核壳型结构变为互穿结构。  相似文献   

9.
PMMA-PAN核壳结构复合乳胶的制备与表征   总被引:1,自引:0,他引:1  
采用疏水引发剂引发的半连续无皂乳液聚合法,合成了Z均流体力学直径约70nm的聚甲基丙烯酸甲酯(PMMA)纳米乳胶。以PMMA纳米乳胶为种子,采用疏水引发剂引发的种子乳液聚合法,制备了PMMA-聚丙烯腈(PAN)核壳结构复合乳胶。采用动态光散射、傅里叶红外光谱、扫描电镜和透射电镜表征了各种乳胶粒的组成、尺寸、结构和微观形态。研究了反应温度、单体用量和表面活性剂用量对PMMA-PAN复合乳胶粒的结构和形态的影响。结果表明:PMMAPAN复合乳胶粒为核壳结构,其壳层厚度可通过改变单体用量进行调整。  相似文献   

10.
以甲基丙烯酸-3-(三甲氧基硅基)丙酯(MPS)修饰的SiO2胶体粒子为种子,甲基丙烯酸叔丁酯(tBMA)为单体、十二烷基硫酸钠(SDS)为乳化剂,采用种子乳液聚合法制备了SiO2/聚甲基丙烯酸叔丁酯的核壳复合微粒。微粒经水解后形成具有pH敏感性的无机/有机复合微粒。研究了影响核壳复合微粒形态结构的因素,结果发现,控制SiO2种子乳液的质量分数在1.5%~2%,可避免聚合过程中生成纯聚甲基丙烯酸叔丁酯乳胶粒子;反应体系中乳化剂SDS的用量超过质量分数0.3%时,易形成纯聚合物乳胶粒子;SDS用量低于质量分数0.15%时,生成的核壳复合微粒易产生团聚;单体和交联剂用量升高,核壳复合微粒的壳层厚度增加,用量过高会导致核壳复合微粒出现团聚现象,并且有纯聚合物乳胶粒子生成。采用TEM、NMR和FTIR及接触角测试技术分析结果表明,复合微粒是由SiO和聚甲基丙烯酸叔丁酯组成的核壳结构微粒。  相似文献   

11.
无乳化剂乳液聚合法合成单分散大粒径高分子微球的研究   总被引:16,自引:0,他引:16  
无乳化剂乳液聚合法合成单分散大粒径高分子微球的研究朱世雄杜金环金熹高陈柳生(中国科学院化学研究所北京100080)关键词无乳化剂乳液聚合,单分散,均相成核,低聚物胶束微米级大粒径单分散高分子微球在标准计量、情报信息、分析化学等许多领域都有广泛的...  相似文献   

12.
In order to obtain functional polymer latex particles with clean surface and with surface carboxyl groups, P(MMA-EA) seed particles with the diameter of 335 nm were first synthesized via soap-free batch emulsion polymerization of methyl methacrylate (MMA) and ethyl acrylate (EA), and then the seeded emulsion copolymerization of MMA, EA and MAA (methacrylic acid) onto the seed particles were performed in the absence of emulsifier. Influences of ingredients and conditions on polymerization, latex particle size (Dp) and its distribution were investigated. Results showed that most of the monomers polymerized onto the seed latex particles in the second step of polymerization by using drop-wise addition method, and Dp increased from 483 nm to 829 nm with the mass ratio of core/shell monomers [C]/[S] decreased from 1:2 to 1:15. It was found that Dp decreased with the increase of MAA and initiator amounts, and the size of the latex particles became uniform with the decrease of MAA amount and with the increase of [C]/[S] value.  相似文献   

13.
 Urethane acrylate anionomer (APUA) as a kind of new type polymerizable emulsifier was synthesized using 2,4-toluene diisocyanate (TDI), polypropylene glycol (PPG), 2-hydroxyethyl methacrylate (HEMA) and dimethylolpropionic acid (DMPA). The critical micelle concentration (CMC) of APUA was measured by the methods of conductance and surface tension. The comparative studies between polymerizable emulsifier AUPA and conventional emulsifier sodium dodecyl sulfate (SDS) were carried out in the emulsion polymerization of methyl methacrylate (MMA). Polymerization kinetics,stability, size and morphology of the latex particles were investigated. It was found that in APUA both water soluble initiator potassium persulfate (KPS) and oil soluble initiator 2,2'-azobisisobutyronitrile (AIBN) can start the reaction of MMA, and the polymerization rate and yield were very high. On using AIBN as an initiator, the conversion-time behavior of MMA with APUA as emulsifier was different to that of SDS as emulsifier, signifying a different nucleation mechanism of the polymer latex particle. The average size of the two kinds of particles is about 50 nm. The particle size decreases with increasing emulsifier concentration. On using KPS as the initiator, APUA as emulsifier, cross-linking hydrogel of PMMA would be formed, but SDS was used as emulsifier and the hydrogel of PMMA was not present.  相似文献   

14.
Stable core‐shell latex was synthesized by semicontinuous seeded emulsion polymerization with core monomers consisting of styrene (St), butyl acrylate (BA), and shell monomers consisting of methyl methacrylate (MMA), eutyl acrylate (EA), and methacrylic acid (MAA). The effects of compound emulsifier amount, mass ratio of anionic/nonionic emulsifier, and initiator amount on latex performance were investigated. By particle size analysis and transmission electron microscopy (TEM) observation, results suggest that final latex particles have clearly core shell structures.  相似文献   

15.
MMA-EA-AA无皂乳液聚合中粒径及粒径分布的控制   总被引:10,自引:0,他引:10  
系统研究了MMA EA AA三元无皂乳液聚合体系中各种因素对乳胶粒大小及分布的影响 ,制得了单分散、粒径在 30 0~ 6 0 0nm可控聚合物乳胶粒 .结果表明 ,在过硫酸铵用量一定的条件下 ,聚合初期加入大量引发剂可同时提高单体转化率和乳胶粒的单分散性 ;随着引发剂和AA用量的增加以及聚合温度的升高 ,胶粒粒径逐渐减小 ,转化率逐渐升高 ;随着NH4 HCO3用量的增加 ,粒径逐渐增大 ,当NH4 HCO3用量达到 0 5g以后 ,转化率逐渐降低 ;搅拌速率为 30 0r min左右时 ,单体转化率最高 ,所得乳胶粒粒径最均一 .  相似文献   

16.
无皂乳液聚合中单分散粒子的形成过程   总被引:17,自引:3,他引:14  
在少量双官能团水溶性共单体(磺化下二酸-聚乙二醇-烯丙基缩水甘油醚酯)存在下进行MMA/BA无皂乳液聚合,用CoulterLS230激光粒径分析仪研究了乳胶粒子的成核机理和单分散粒子的形成过程,乳胶粒子的成粒程属多步成粒机理,先均相成核,形成不稳定的初始粒子,然后凝聚成稳定乳胶粒,其粒径分布经历了先变宽后变窄的过程,这是聚合过程中成核-凝聚-增长共同作用,相互竞争的结果,它还导致聚合初期出现周期成  相似文献   

17.
The emulsion polymerization of methyl methacrylate (MMA) and styrene (St) were investigated with using polyamidoamine (PAMAM) dendrimer as seed, potassium persulfate as initiator and sodium dodecyl sulfate as emulsifier. The effects of 4.0GPAMAM dendrimer concentration, initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature on the monomer conversion and polymerization rate were investigated. At the same time, the influence of the generation of PAMAM dendrimer on latex particle size was studied also. The results showed that the monomer conversion and polymerization rate increased with increasing initiator concentration, emulsifier concentration, monomer concentration, and polymerization temperature. But polymerization rate increased firstly with an increase in the 4.0GPAMAM dendrimer from 0.03 g to 0.09 g and then decreased with further increase to 0.12 g. When the concentration of 4.0GPAMAM dendrimer less than 1.449 × 10?4 mol/L, the kinetic equation can be expressed by Rp∝[4.0GPAMAM]0.772[SDS]0.562[KPS]0.589[M]0.697, and the activation energy (Ea) of emulsion polymerization is 62.56kJ/mol. In additional, the copolymer latex particle size decreased and possessed monodispersity with increasing the generation of PAMAM dendrimer. According to FT-IR spectrum analysis, PAMAM dendrimer is successfully incorporated into the poly(PAMAM-St–MMA) latex particles.  相似文献   

18.
The formation mechanism of monodisperse polymer latex particles in the emulsifier-free emulsion polymerizationof methyl methacrylate and butyl acrylate with potassium persulfate as initiator was investigated. A multi-step formationmechanism for the monodisperse polymer particles was proposed. The nucleation mechanism is considered to be thecoagulation of the precursor particles by homogeneous nucleation when the primary particles reach a critical size with highsurface charge density and sufficient stability. It had been proved by a special experiment that the early latex particles formedby the coagulation were stable. The primary particles grow by absorbing monomers and radicals in the polymerization systemand then become colloidally unstable again due to the understandable decrease of particle surface charge density, which leadsto the aggregation of the growing particles and the formation of larger latex pedicles therefrom. Aner the nucleation period,the preferential aggregation of the smaller particles in the propagation process leads to the change of the particles towards auniform size and narrower particle size distribution. The coexistence and competition of homogeneous nucleation,coagulation, propagation and aggregation result in the increase of the polydispersity index (U = D_(43)/D_(10)) in the first Stage,then its decrease in the later stage because of the competition of propagation and aggregation, and the gradual formation ofthe monodisperse particles.  相似文献   

19.
研究了表面活性单体「磺化-十二醇-烯丙基甘油-丁二酸酯钠盐(ZC-L)」的用量对MMA/BA/ZC-L乳液聚合速率和粒径的影响,用Corltir LS230型激光粒径分析仪测定聚合过程中乳液的粒径和粒径分布变化,并与MMA/BA无皂乳液聚合及十二烷基苯磺酸钠存在下的MMA/BA乳液聚合作了比较。「ZC-L」〈CMC时,成核机理为均相成核机理,乳胶粒需依靠粒子间的凝聚来提高表面电荷密度而稳定;「ZC  相似文献   

20.
复合微乳液聚合制备P(MMA-UA)纳米乳胶粒子的研究   总被引:14,自引:0,他引:14  
将聚氨酯预聚体可聚合乳化剂 (APUA)和甲基丙烯酸甲酯 (MMA)的复合微乳液体系 ,分别用水溶性过硫酸钾 (K2 S2 O8)和油溶性偶氮二异丁腈 (AIBN)作引发剂 ,进行微乳液聚合研究 ,制备了P(MMA UA)复合纳米乳胶粒子 .研究了APUA用量、聚合温度对聚合动力学的影响 ;用透射电子显微镜 (TEM)观察了不同乳化剂浓度及引发剂体系对胶粒形态、大小及分布的影响 .结果表明 ,用可聚合乳化剂APUA可制得稳定性很好的P(MMA UA)纳米级核 壳型乳胶粒子 ,乳胶粒径在 5 0nm左右 .随着乳化剂用量增加 ,粒子变小 ;不同类型的引发剂对胶乳的性质有较大影响 ,以APUA为乳化剂 ,K2 S2 O8为引发剂 ,在聚合反应过程中或在聚合反应后的放置中 ,会出现P(MMA UA)的纳米水凝胶 (Nanogel)现象 .  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号