Bi4(Ti1/3Sn2/3)3O12掺杂BaTiO3基X8R陶瓷微观结构与介电性能

研究了Bi4(Ti1/3Sn2/3)3O12掺杂对钛酸钡基陶瓷微观结构和介电性能影响。结果表明,掺杂Bi4(Ti1/3Sn2/3)3O12后钛酸钡基陶瓷晶粒明显长大,同时烧结温度可由1 280℃降低至1 180℃。系统的介电性能和Bi4(Ti1/3Sn2/3)3O12的掺杂量有密切关系。当Bi4(Ti1/3Sn2/3)3O12的掺杂量从0.5mol%增加到2mol%,体系的居里峰被明显压低和展宽,当掺杂量为2mol%时居里峰变得不明显。当Bi4(Ti1/3Sn2/3)3O12的掺杂量从0.5mol%增加到2mol%,系统的居里温度由131℃升高至139℃。当Bi4(Ti1/3Sn2/3)3O12的掺杂量为1mol%时,钛酸钡基陶瓷介电常数为1 930,介电常数温度变化率为5%(-55℃),13%(134℃),-8%(150℃),满足X8R标准。     

Bi_(0.5)Na_(0.5)TiO_3的制备及光催化性能研究

以Bi(NO3)3·5H2O、Na OH、Ti(OC4H9)4为原料,采用水热法制备Bi0.5Na0.5Ti O3纳米光催化剂。用XRD、TEM表征了Bi0.5Na0.5Ti O3光催化剂的结构和形貌。以亚甲基蓝为模型污染物,考察了不同浓度的Na OH对Bi0.5Na0.5Ti O3晶体在紫外光和可见光照射下光催化活性的影响。通过荧光技术研究了Bi0.5Na0.5Ti O3光催化剂表面羟基自由基的生成,探究了清除剂对光催化降解污染物活性的影响。结果表明:Na OH的浓度对Bi0.5Na0.5Ti O3光催化剂的紫外光和可见光活性有很大的影响,当Na OH浓度为8mol·L-1时制备的Bi0.5Na0.5Ti O3晶体光催化活性最高,光照1h,亚甲基蓝的紫外及可见光催化降解率分别达到69.8%、53.4%,在光催化降解过程中·O2ˉ和·OH起主要作用,尤其是·O2-起了重要作用。     

Bi2Ti2O7薄膜的自组装法制备及表征

以Bi(NO3)3·5H2O和Ti(OC4H9)4为原料,采用自组装单层膜技术,在负载有功能化三氯十八烷基硅烷(octadecyl-trichloro-silane,OTS)的FTO基板上制备了Bi2Ti2O7薄膜。基板表面的亲水性测试表明,紫外照射使OTS自组装单层膜表面由疏水转变为亲水,实现功能化。借助X射线衍射(XRD)、X射线能量色散谱(EDS)、扫描电子显微镜(SEM)和原子力显微镜(AFM)分析分别对Bi2Ti2O7薄膜的组成、结构和微观形貌进行了表征。结果表明,沉积溶液浓度为0.02 mol·L-1时,所得Bi2Ti2O7薄膜均匀致密。560℃热处理1 h、厚度为0.4μm的Bi2Ti2O7薄膜在100 kHz的介电常数为153,介电损耗为0.089。     

Yb2O3对Bi2O3-MoO3催化剂性能的影响

在Bi2O3-MoO3复合氧化物催化剂中加入Yb2O3，可明显提高异丁烯转化率和生成甲基丙烯醛的选择性，用XRD、FT-Raman光谱和SEM技术研究了催化剂的组成和性质，Bi2O3—MoO3催化剂的成分主要是α-Bi2Mo3O12，添加镱后出现了Yb2Mo3O12的吸收峰；且Bi2O3-MoO3-Yb2O3催化剂的FT—Raman光谱图在363cm^-1处出现了Yb—O伸缩振动峰，同时既Bi2O3-MoO3催化剂的铝-氧振动发生红移，表明镱的加入使铝-氧键的振动减弱，使Bi2O3-MoO3-Yb2O3催化剂有较高传递晶格氧给予异丁烯的能力，导致异丁烯转化率和生成甲基丙烯醛的选择性均显著提高。     

Ti(Ⅳ)掺杂Bi_2O_3电子结构和可见光催化活性的原理

密度泛函理论(DFT)计算对掺杂体系新型环境光催化剂设计开发具有指导意义.基于DFT框架下的第一性原理平面波超软赝势方法(USPP),对α、β、γ、δ-Bi2O3晶体几何结构分别进行了优化计算,从理论上得到了Bi2O3的总体态密度(TDOS)和Bi、O原子的分波态密度(PDOS).在此基础上对Bi2O3超晶胞进行Ti(IV)的掺杂计算,讨论了Ti(IV)掺杂对各种Bi2O3的电子结构和光吸收特性的影响.结果表明Ti(IV)掺杂Bi2O3晶体后,Ti(IV)的3d轨道进入禁带并与O2p、Bi6p轨道作用,使禁带宽度(Eg)变小,Bi2O3的吸收边红移,从而有助于Bi2O3光催化活性的改善.通过水热合成法制备的Ti(IV)掺杂Bi2O3样品的紫外-可见光漫反射光谱验证了计算的结果.在光催化降解有机染料结晶紫的实验中,光催化剂活性的改善进一步得到证实.     

USP制备高光电活性Ti掺杂Fe2O3薄膜

本文报道了采用超声喷雾裂解法(USP)法制备α-Fe2O3以及不同厚度的Ti掺杂α-Fe2O3薄膜,并通过XRD、XPS、SEM、IPCE表征了合成的薄膜。XRD测试结果表明,Ti掺杂和纯相Fe2O3均为α相并在(110)晶面优先生长;从AFM图中看出Fe2O3晶粒呈尖峰状垂直于平面排列;由XPS分析得知Ti离子在Fe2O3薄膜中以Ti4+和Ti3+两个价态存在;由光电效率表征可知,吸收光电转换效率(APCE)值是随着样品薄膜厚度增加而减小,在厚度为20nm时APCE为58%,对于粉末Fe2O3光催化材料是粒径尺寸越小光利用率越高;然而Fe2O3薄膜的IPCE值在厚度为60nm时最高达到23.5%,此时光利用效率最大。     

Fe_2O_3掺杂TiO_2薄膜对甲基紫溶液光催化降解

甲基紫是一种相当稳定的有机物 ,能被 Ti O2 光催化降解 .本文采用 sol-gel工艺在玻璃表面制得了均匀透明的 Ti O2 薄膜 ,研究了热处理温度、涂覆层数、掺杂 Fe2 O3 等制备工艺 ,以及溶液 p H值和助催化剂H2 O2 等因素对 Ti O2 薄膜的光催化性能和稳定性的影响 .结果表明 ,掺 Fe2 O3 的 Ti O2 薄膜对甲基紫的降解率明显优于未掺 Fe2 O3 的 Ti O2 薄膜 .     

非铁电巨介电压敏材料CCTO

本文主要介绍了近年来一种新型类钙钛矿型非铁电巨介电非线性压敏陶瓷材料——CaCu3Ti4O12,概述了其在晶体结构、相结构、微观形貌、多条件下介电特性和I-V特性等方面的研究进展。比较了CaCu3Ti4O12陶瓷的各种巨介电性理论和模型,阐述了压敏特性的起源。在讨论CaCu3Ti4O12陶瓷巨介电性和压敏特性机理的同时,指出了CaCu3Ti4O12作为介电材料和压敏材料的研究方向及应用的可能性。掺杂、复合及热处理工艺等对CaCu3Ti4O12电性能影响的系统性研究工作还需要进一步深入;纳米化可能会导致其某项特性的进一步提升,而薄膜化尽早与微电子领域的需要相结合会产生更广阔的应用空间。     

掺Ti和未掺Ti的α-Fe_2O_3薄膜光电性质的研究

本文采用旋涂法制备了掺Ti和未掺Ti的Fe2O3薄膜,并对其薄膜的结构和光电特性进行了系统测试分析。XRD结果证实掺Ti和未掺Ti的薄膜均为α-Fe2O3。SEM测试表明α-Fe2O3薄膜微观结构为纳米线结构,具有沟壑结构,粒径长度约为150nm,掺杂Ti使薄膜更均匀致密,晶体颗粒更小,比表面积更大。紫外-可见光谱实验发现了掺杂Ti使薄膜产生"蓝移",禁带宽度大,验证了SEM测试结果。IPCE实验结果结果说明了掺杂Ti的α-Fe2O3薄膜的光电性能大大好于未掺杂的薄膜。     

BiO3对染料的光催化降解性能

近年来 ,利用半导体材料光催化降解有害污染物已成为比较热门的研究课题之一 [1,2 ] ,因其能有效地利用太阳能并在反应中产生强氧化能力的空穴和羟基自由基 ,因而备受人们的关注 .目前使用较多的是催化活性高 ,稳定性好的 Ti O2 [3] ,但由于其带隙较宽 ( 3.2 e V) ,只能吸收波长 λ≤ 387nm的紫外光 .因此研制新型光催化剂或改善催化效率仍是重要研究课题 .近年来 ,有报道用 Bi2 O3光催化处理含亚硝酸盐废水的实验研究 [4 ] ,结果比较满意 .本研究对 Bi2 O3的制备、表征及其作光催化剂处理各种染料溶液进行实验 ,结果表明 ,Bi2 O3具有较…     

局部化学法合成K0.5Bi0.5TiO3片状晶粒及其反应机理研究

以含铋层状Bi4Ti3O12(BIT)晶粒作为反应前驱体, 通过熔盐环境下的局部化学反应法制备了片状钛酸铋钾(K0.5Bi0.5TiO3, KBT)陶瓷粉体晶粒. 分析结果表明, 所制备的KBT陶瓷晶粒平均直径约为15～20 μm, 厚度小于2 μm. 分析了由含铋层状型BIT向钙钛矿型KBT片晶转化的形成机制, 并讨论了反应路径对最终产物形貌的影响规律.     

Synthesis of Bi2O3 and Bi4(SiO4)3 Thin Films by the Sol-Gel Method

Bi2O3 thin films were prepared by dipping silica slides in ethanolic solutions of tris(2,2-6,6-tetramethylheptane-3, 5-dionato)bismuth(III) [Bi(dpm)3] [1] and heating in air at temperatures 500°C. Bi4(SiO4)3 homogeneous thin films were obtained from the reaction of the bismuth oxide coating with the silica glass substrate at temperatures higher than 700°C. For heat treatments at temperatures between 600°C and 700°C, Bi2SiO5 coatings were obtained. The composition and microstructure evolution of the films were determined by Secondary Ion-Mass Spectrometry (SIMS), X-Ray Photoelectron Spectroscopy (XPS) and Glancing Angle X-Ray Diffraction (GA-XRD). The synthesis procedure was reproducible and allowed the control of the Bi2O3 phase composition. Moreover, the thin film annealing parameters were correlated with the formation of bismuth silicates, among which Bi4(SiO4)3 (BSO) is very appealing for the production of fast light-output scintillators [2].     

电沉积Bi2Te3基薄膜的电化学阻抗谱研究

以不锈钢为基底,利用电化学沉积方法制备Bi2Te3基薄膜材料,并采用X射线衍射技术、电子探针微观分析等方法对薄膜进行结构和成分表征,通过电化学阻抗谱技术对不锈钢表面Bi2Te3的电化学沉积机理进行了初步探讨.结果表明Bi-Te和Bi-Te-Se体系具有相似的电化学沉积机理,即Bi3+和2HTeO+或H2SeO3首先被还原为Bi单质和Te或Se单质,然后Bi单质与Te或Se单质反应生成Bi2Te3基化合物,而Bi-Sb-Te体系中,2HTeO+首先被还原为Te单质,生成的Te再与Bi3+和Sb(III)反应生成Bi2Te3基化合物,三种体系的沉积都受电化学极化控制.     

Heterobimetallic bismuth-transition metal salicylate complexes as molecular precursors for ferroelectric materials. Synthesis and structure of Bi(2)M(2)(sal)(4)(Hsal)(4)(OR) (4) (M = Nb,Ta; R = CH(2)CH(3), CH(CH(3))(2)), Bi(2)Ti(3)(sal)(8)(Hsal)(2), and Bi(2)Ti(4)(O(i)Pr)(sal)(10)(Hsal) (sal = O(2)CC(6)H(4)-2-O; Hsal = O(2)CC(6)H(4)-2-OH)

The reactions between triphenylbismuth, salicylic acid, and the metal alkoxides M(OCH(2)CH(3))(5) (M = Nb, Ta) or Ti[OCH(CH(3))(2)](4) have been investigated under different reaction conditions and in different stoichiometries. Six novel heterobimetallic bismuth alkoxy-carboxylate complexes have been synthesized in good yield as crystalline solids. These include Bi(2)M(2)(sal)(4)(Hsal)(4)(OR)(4) (M = Nb, Ta; R = CH(2)CH(3), CH(CH(3))(2)), Bi(2)Ti(3)(sal)(8)(Hsal)(2), and Bi(2)Ti(4)(O(i)Pr)(sal)(10)(Hsal) (sal = O(2)CC(6)H(4)-2-O; Hsal = O(2)CC(6)H(4)-2-OH). The complexes have been characterized spectroscopically and by single-crystal X-ray diffraction. Compounds of the group V transition metals contain metal ratios appropriate for precursors of ferroelectric materials. The molecules exhibit excellent solubility in common organic solvents and good stability against unwanted hydrolysis. The nature of the thermal decomposition of the complexes has been explored by thermogravimetric analysis and powder X-ray diffraction. We have shown that the complexes are converted to the corresponding oxide by heating in an oxygen atmosphere at 500 degrees C. The mass loss of the complexes, as indicated by thermogravimetric analysis, and the resulting unit cell parameters of the oxides are consistent with the formation of the desired heterobimetallic oxide. The complexes decomposed to form the bismuth-rich phases Bi(4)Ti(3)O(12) and Bi(5)Nb(3)O(15) as well as the expected oxides BiMO(4) (M = Nb, Ta) and Bi(2)Ti(4)O(11).     

光生电荷梯度连续传递链的构筑及对光催化性能的增强作用

选取能带位置匹配的γ-Bi₂O₃, α-Bi₂O₃和Bi₄Ti₃O₁₂, 采用等体积浸渍法原位构筑了具有梯度能级的Bi₄Ti₃O₁₂@α/γ-Bi₂O₃三元同素结光催化剂. 光催化降解高浓度罗丹明B(RhB)和四氯苯酚(4-CP)的实验结果表明, 相比于γ-Bi₂O₃和α/γ-Bi₂O₃, Bi₄Ti₃O₁₂@α/γ-Bi₂O₃显示出优异的光催化活性, 其中0.5%Bi₄Ti₃O₁₂@α/γ-Bi₂O₃显示了最佳的光催化性能, 光降解RhB(或4-CP)的活性是γ-Bi₂O₃的32倍(或10.4倍)和α/γ-Bi₂O₃的4.4倍(或2.2倍). 光电性质表征结果证实, Bi₄Ti₃O₁₂@α/γ-Bi₂O₃三元同素结具有高效的光生电荷分离和迁移效率, 这是Bi₄Ti₃O₁₂@α/γ-Bi₂O₃三元同素结具有较高光催化性能的主要原因之一.     

Preparation and Optical Properties of Gold-Dispersed BaTiO3, PGO (Pb5Ge3O11) and PLT (Pb1-1.5xLaxTiO3) Thin Films by Sol-Gel Process

Gold-dispersed BaTiO₃, PGO and PLT thin films, which will be used for third-order nonlinear optical devices, were prepared by sol-gel process with spin-coating using HAuCl₄4H₂O, Ba(CH₃COO)₂, Ti[O(CH₂)₃CH₃]₄, Pb(CH₃COO)₂3H₂O, Ge[O-n-C₄H₉]₄, La(CH₃COO)₃1.5 H₂O as starting materials. The thin films were heat-treated in air at temperatures ranging from 400 to 800 for 1 h. The nonlinear optical property of these thin films was measured by the degenerate four-wave mixing (DFWM) method using a frequency-doubled Nd: YAG laser with 20 ps pulse duration. Third-order nonlinear susceptibility χ⁽³⁾ of gold-dispersed BaTiO₃, PGO and PLT thin films with 5 vol% of gold were 1.410⁻⁶ esu, 3.510⁻⁷ esu respectively. The large χ⁽³⁾ may be ascribed to the high dielectric constant of the films.     

Synthesis, composition, and structure of sillenite-type solid solutions in the Bi2O3-SiO2-MnO2 system

Individual compounds and solid solutions are obtained under hydrothermal conditions in the Bi(2)O(3)-SiO(2)-MnO(2) system in the form of faceted crystals and epitaxial films on the Bi(24)Si(2)O(40) substrate. The crystals have the shape of a cube (for the molar ratio of the starting components Na(2)SiO(3)·9H(2)O:Mn(NO(3))(2)·6H(2)O > 1), a tetrahedron (for Na(2)SiO(3)·9H(2)O:Mn(NO(3))(2)·6H(2)O < 1), or a tetrahedron-cube combination (for Na(2)SiO(3)·9H(2)O:Mn(NO(3))(2)·6H(2)O = 1). Crystal-chemical analysis based on the data of single-crystal and powder X-ray diffraction, IR spectra, and the results of calculation of the local balance by the bond-valence method reveals formation of the Bi(24)(Si(4+),Mn(4+))(2)O(40) phases, which probably include Mn(5+) ions (epitaxial films), as well as the Bi(24)(Si(4+),Bi(3+),Mn(4+))(2)O(40) and Bi(24)(Si(4+),Mn(4+))(2)O(40) phases in the (1 - x)Bi(3+)(24)Si(4+)(2)O(40) - x(Bi(3+)(24)Mn(4+)(2)O(40)) system and the Bi(24)(Bi(3+),Mn(4+))(2)O(40) phase in the (1 - x)Bi(3+)(24)Bi(3+)(2)(O(39)?(1)) - x(Bi(3+)(24)Mn(4+)(2)O(40)) system. Precision X-ray diffraction studies of single crystals of the Bi(24)(Bi,Si,Mn)(2)O(40) general composition show that these sillenites crystallize in space group P23 and not I23 as the Bi(24)Si(2)O(40) phase. The dissymmetrization of sillenite phases is observed for the first time. It is explained by a kinetic (growth) phase transition of the order-disorder type due to population of a crystallographic site by atoms with different crystal-chemical properties and quasi-equilibrium conditions of crystal growth in the course of a hydrothermal synthesis below 400 °C at unequal molar amounts of the starting components in the batch.     

Praseodymium(III)-substituted bismuth titanate thin-film generation using metallo-organic precursors with an M-O-C skeleton and sol-gel technique and employing 4f-4f transition spectra as a probe to explore kinetic performance

A hetero-trimetallic lanthanide-substituted bismuth titanate (BLT, where lanthanide is praseodymium) with stoichiometry Pr(0.75)Bi(3.25) Ti(3)O(12) has been obtained as both highly homogenized crystalline and amorphous thin films using three different BLT precursors: (i). precursor A-(Pr(OC(3)H(7)(i))(3),Bi(OOCCH(3))(3),Ti(OC(3)H(7)(i))(4)); (ii). precursor B-(Pr(OC(3)H(7)(i))(2)(acac),Bi(OOCCH(3))(3),Ti(OC(3)H(7)(i))(3)(acac)); and (iii). precursor C-(Pr(OC(3)H(7)(i))(2)(acac),Bi(OOCCH(3))(3),Ti(OC(3)H(7)(i))(2)(acac))(2). These three BLT precursors (A, B, C) are prepared by reacting constituent monometallic precursors in the desired stoichiometry and by employing controlled acidic hydrolysis via the sol-gel method. Paramagnetic Pr(III), being a f(2) ion, gives characteristic 4f-4f transition bands (3H(4)-->3P(2), 3H(4)-->3P(1), 3H(4)-->3P(0), and 3H(4)-->1D(2)) in the visible region, the intensities of which have been found to be highly sensitive to even minor changes in the immediate coordination around Pr(III), occurring as a result of the progress of polycondensation reactions of three multicomponent BLT sols. We have used the changes with time in the intensities (represented by oscillator strengths of these four 4f-4f bands) and the magnitude and variation of the spectral parameters evaluated from the observed spectra with a view toward monitoring the sol-gel reactions of BLT precursors A, B, and C. 4f-4f transition spectra of the aliquots, withdrawn from the hydrolyzing A, B, and C sols at different time intervals, represent the changes occurring in the Pr(III) environment with the progress of sol-gel hydrolysis of BLT, and are used to investigate the kinetic performance in hydrolysis of the three precursors. Kinetics of hydrolysis of precursors A, B, and C indicate that all four f-f transition bands of Pr are almost equally sensitive to precursor hydrolysis in the order A>B>C.     

Neodymium(III)-substituted bismuth titanate thin film generation using metal alkoxo, acyloxo, and beta-diketonato precursors employing a sol-gel route and using 4f-4f transition spectra as probes to explore kinetic performance

Heterotrimetallic lanthanide-substituted bismuth titanate (BLT, where lanthanide is neodymium) with stoichiometry Nd(0.75)Bi(3.25)Ti(3)O(12) has been obtained in both highly homogenized crystalline and amorphous thin film forms using three different multicomponent precursors, A (formed from Nd(OC(3)H(7)(i))(3), Bi(OOC.CH(3))(3), and Ti(OC(3)H(7)(i))(4) taken in the desired stoichiometry), B (formed from Nd(OC(3)H(7)(i))(2)(acac), Bi(OOC.CH(3))(3), Ti(OC(3)H(7)(i))(3)(acac)), and C (formed from Nd(OC(3)H(7))(acac)(2), Bi(OOC.CH(3))(3), Ti(OC(3)H(7))(3)(acac), in the desired stoichiometry), and employing controlled acidic hydrolysis during the sol-gel method. Paramagnetic Nd(III), an f(3) metal ion, gives characteristic 4f-4f transition spectra in the visible and near infrared region. The sensitivity of 4f-4f transitions to minor coordination changes around paramagnetic Nd(3+) has been used to monitor hydrolysis during the progress of the sol-gel process of the multicomponent BLT precursors. The variation of intensities (oscillator strengths) of 4f-4f bands during hydrolysis, as well as the variation of Judd-Ofelt intensity parameters, has helped in following the preliminary kinetics of hydrolysis. Highly complex polycondensation reactions occurred during sol-gel hydrolysis of three BLT precursors. Rates of hydrolysis with respect to five 4f-4f transitions of Nd(III) were determined. The different types of multicomponent BLT precursors have shown different rates of hydrolysis, following the reactivity trend A > B > C.