Monodentate aminophosphine nickel(II)‐ and palladium(II)‐catalyzed ethylene oligomerization and norbornene polymerization

Nickel(II) and palladium(II) complexes of monodentate aminophosphine ligands were prepared and characterized. In ethylene oligomerization and subsequent Friedel–Crafts alkylation of toluene, the Ni(II) complexes Ni‐1 and Ni‐2 were activated with aluminium co‐catalysts and generated tandem catalysts with high activities (up to 1.1 × 10⁶ g (mol Ni)^?1 h^?1) which are comparable with those of previously reported bidentate Ni(II) catalysts. The Pd(II) precatalyst Pd‐1 showed high activities (up to 2.0 × 10⁵ g (mol Pd)^?1 h^?1) in the polymerization of norbornene.     

硅烷基Schiff碱共价修饰纳米二氧化硅负载过渡金属催化乙烯齐聚性能

将3种水杨醛Schiff亚胺配合过渡金属（Si-Schiff-M,M=Ni,Co,Cr）通过共价键接枝到纳米二氧化硅,制备了3种硅烷基Schiff碱共价修饰纳米二氧化硅负载过渡金属催化剂（Si-Schiff-SiO₂-M）,并对其催化乙烯齐聚性能进行了研究;采用元素分析、红外光谱、扫描电子显微镜和电感耦合等离子色谱表征了3种Si-Schiff-SiO₂-M的结构和形貌。以甲基铝氧烷（MAO）为助催化剂,研究了反应条件及催化活性中心种类对3种Si-Schiff-SiO₂-M催化乙烯齐聚产物性能的影响。结果表明,当Si-Schiff-SiO₂-M用量为7 μmol, n（Al）/n（M）（M=Cr,Ni,Co）为500,反应温度为35 ℃,反应压力为0.5 MPa和反应时间为30 min时, Si-Schiff-SiO₂-Cr、Si-Schiff-SiO₂-Ni和Si-Schiff-SiO₂-Co催化乙烯齐聚活性分别为1.92×10⁵ g/（mol Cr·h）、2.17×10⁵ g/（mol Ni·h）和2.07×10⁵ g/（mol Co·h）,且3种催化剂催化乙烯齐聚产物主要是C4和C6烯烃。Si-Schiff-SiO₂-M由于载体的限域效应,其催化乙烯齐聚活性低于相应的均相催化剂（Si-Schiff-M）,但产物分布较均相催化剂窄。Si-Schiff-SiO₂-M具有良好的循环利用性,3次循环使用后,3种负载型催化剂催化乙烯齐聚活性分别为1.39×10⁵ g/（mol Cr·h）、1.68×10⁵ g/（mol Ni·h）和1.42×10⁵ g/（mol Co·h）。     

Flow Injection Chemiluminescence Method for Nalbuphine Hydrochloride in Pharmaceutical Formulations Using Tris(2,2'-bipyridyl)ruthenium(II) Chloride-diperiodatocuprate(III) Reaction

Asensitive and selective method employing chemiluminescence(CL) coupled with flow injection(FI) is reported for nalbuphine hydrochloride(NAL) assay in pharmaceutical formulations. The enhancement effect of NAL on the CL reaction between tris(2,2'-bipyridyl)ruthenium(II) chloride-diperiodatocuprate(III) {Ru[(bpy)₃]²⁺-Cu(III) complex} in acidic medium is used as analytical measurement. The optimal conditions of the CL reaction were sulfuric acid 1.0×10^-3 mol/L, Ru[(bpy)₃]²⁺ 7.5×10^-5 mol/L, Cu(III)/Ag(III) complexes 4.0×10^-4/5.0×10^-4 mol/L, sample loop volume of 120 μL and flow rate of 2.5 mL/min. The sensitivities of the method in terms of detection(S/N=3) and quantification(S/N=10) limits are 5×10^-4 and 0.001 ppm(1 ppm=1 mg/L), respectively. The linear response of the instrument in the form of CL intensity with respect to NAL concentration is over the range 0.001-15.0 ppm(R²=0.9999) with relative standard deviation from 0.8% to 3.2% and injection throughput of 120 injection/h. The applications of the method include the quantitative analysis of NAL in pharmaceutical injection samples. Variations and the average results of the proposed method are not signi-ficantly different from the results of a reported method by applying F- and paired student t-test. The most likely CL reaction mechanism is written in accordance with spectrophotometric and CL studies.     

Potentiometric study of Cd(II) and Pb(II) complexation with two high molecular weight poly(acrylic acids); comparison with Cu(II) and Ni(II)

The cadmium (II) or lead (II) complex formation with two poly(acrylic acids) of high molecular weight (Mw=2.5×10⁵ and 3×10⁶) was investigated in dilute aqueous solution (NaNO₃ 0.1 mol l⁻¹; 25°C). Potentiometric titrations were carried out to determine the stability constants of the MA and MA₂ complex species formed. Bjerrum’s method, modified by Gregor et al. (J. Phys. Chem. 59 (1955) 34–39), for the study of polymeric acids was used. The results were compared to those previously obtained in the same conditions with copper (II) and nickel (II) . It appeared that the two polymers under study present similar binding properties and that the stability constants of the complex species formed increased in the following order, depending on the metal ion: Ni(II)β₁₀₂ was found to be close to 7.0) and allowed the formation of the predominant PbA₂ species in a quite large pH domain. Finally, the greater stability of PAA complexes compared to those of their monomeric analogs, glutaric and acetic acids, was confirmed.     

Potentiometric study of Cu(II) and Ni(II) complexation with two high molecular weight poly(acrylic acids)

The copper (II) or nickel (II) complex formation with two poly(acrylic acids) of high molecular weight (Mw=2.5×10⁵ and 3×10⁶) was investigated in aqueous dilute solution (NaNO₃ 0.1 mol l⁻¹; 25°C). Potentiometric titrations were carried out, first to precise the acid-base properties of the two polymers, and secondly to determine the stability constants of the MA and MA₂ complex species formed. The Bjerrum's method, modified by Gregor et al. (J. Phys. Chem., 59 (1955) 34–39), for the study of polymeric acids was used. The results obtained showed that both polymers present very similar properties. As expected, copper (II) is more readily bound to poly(acrylic acids). CuA₂ was the predominant observed species; the global stability constant log β₁₀₂ was found to be close to 6.6. With nickel (II), none of the complex species MA or MA₂ becomes predominant (log β₁₀₂=5.5). Finally, the PAA complexes present a greater stability compared with that of monomeric analogs.     

Ni(II) and Pd(II) complexes bearing benzocyclohexane–ketoarylimine for copolymerization of norbornene with 5‐norbornene‐2‐carboxylic ester

A serial of late transition metal complexes, which bearing Benzocyclohexane–ketoarylimine ligand and named as Mt(benzocyclohexane–ketoarylimino)₂ {Mt(bchkai)₂: Mt=Ni or Pd; bchkai=C₁₀H₈(O)CN(Ar)CH₃; Ar=naphthyl or fluoryl}, have been synthesized and characterized. The molecular structures of the ligands and nickel complex have been confirmed by X‐ray single‐crystal analyses. The nickel complexes exhibited very high activity up to 2.7 × 10⁵ g_polymer/mol_Ni·h and palladium complexes showed high activity up to 2.3 × 10⁵ g_polymer/mol_Pd·h for norbornene (NB) homo‐polymerization with tris(pentafluorophenyl)borane as cocatalyst. The four complexes were effective for copolymerization of NB and 5‐norbornene‐2‐carboxylic acid methyl ester (NB‐COOCH₃) in relatively high activities (0.1–2.4 × 10⁵ g_polymer/mol_Mt·h) and produced the addition‐type copolymers with relatively high molecular weights (0.5 × 10⁵–1.2 × 10⁵ g/mol) as well as narrow molecular weight distributions (PDI < 2 for all polymers). Influences of the metals and comonomer feed content on the polymerization activity as well as on the incorporation rates (20.9–42.6%) were investigated. The achieved NB/NB‐COOCH₃ copolymers were confirmed to be noncrystalline, exhibited good thermal stability (T_d > 400°C) and showed good solubility in common organic solvents. © 2012 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2012     

Extraction and spectrophotometric determination of trace amount of Pd(II) with 2,2'-dithiodianiline

A method for the extraction-spectrophotometric determination of palladium with 2,2′-dithiodianilline (DTDA) is described. DTDA–Pd(II) complex is extracted from an aqueous solution with pH 3 into isobutyl methyl ketone (IBMK) layer. The absorbance is measured at 397 nm and the molar absorptivity found to be 1.47×10⁶ l mol⁻¹ cm⁻¹. The complex system conforms to Beer's law over the range 0.3–220 ng ml⁻¹ palladium (II). The effect of pH (1–6), NaClO₄ concentration, DTDA concentration and shaking time were studied. The ratio of the metal ion to ligand molecules in the complex and its stability constant were found to be 1:1 and 1.45×10⁶, respectively. The tolerance limit for many cations and anions have been determined. Finally the method has been applied successfully to the determination of palladium in synthetic mixtures, alloy and catalyst samples.     

Hyperbranched macromolecules bridged salicylaldimine cobalt complexes: synthesis,characterization and ethylene oligomerization studies

A series of novel 1.0 generation (1.0G) hyperbranched macromolecules bridged salicylaldimine cobalt complexes were synthesized in high yields. The compounds were characterized by fourier transform infrared (FT-IR) spectroscopy, ultraviolet (UV) visible spectroscopy, electrospray ionization mass spectrometry (ESI–MS), elemental analysis and thermal gravimetric analysis (TGA), as well as were investigated as precatalysts for the oligomerization of ethylene. Upon activation with methylaluminoxane (MAO) and diethylaluminumchloride (DEAC), the cobalt precatalysts showed moderate catalytic activities in the range of 10⁵ g/(mol Co h) in ethylene reactivity with the high selectivity for the butenes and high carbon number olefins products. The correlation between cobalt complexes and their catalytic activities and product distribution were investigated in detail under various reaction parameters. The research results showed that the catalytic activities of precatalysts increased with the increase of ethylene pressure and Al/Co molar ratio; however, the catalytic activities firstly increased and then decreased with the increase of reaction temperature. The highest activity of 2.54 × 10⁵ g/(mol Co h) and 50.18% selectivity of high number carbon olefins was obtained under the reaction temperature of 25 °C, ethylene pressure of 0.5 MPa, and Al/Co molar ratio of 1500. In addition, the nature of solvent and co-catalyst, as well as the structure of precatalysts, significantly affected both the activity and the product distribution of the resultant catalysts.     

Sequential flow-injection spectrophotometric determination of iron(II) and iron(III) by copper(II)-catalyzed reaction with Tiron

A flow injection method for the sequential determination of iron(II) and iron(III) was developed. It is based on the differential reaction kinetics of iron(II) and iron(III) with Tiron in a double-injection FI system. The proposed method employs the accelerating action of copper(II) for the oxidation of iron(II) in the presence of Tiron. A linear calibration graph is obtained for iron (II) and iron(III) in the concentration range 1.8 × 10^–5– 1.8 × 10^–4 mol/L; the throughput of samples is 30 injections/h.     

Ethylene oligomerization by diimine iron(II) complexes/EAO

The catalytic properties of a series of Fe(II) diimine complexes (diimine=N,N′-o-phenylenebis(salicylideneaminato), N,N′-ethylenebis(salicylideneaminato), N,N′-o-phenylenebisbenzal, N,N′-ethylenebisbenzal) in combination with ethylaluminoxane (EAO) for ethylene oligomerization have been investigated. Treatment of the iron(II) complexes with EAO in toluene generates active catalytic systems in situ that oligomerize ethylene to low-carbon olefins. The effects of reaction temperature, ratios of Al/Fe and reaction periods on catalytic activity and product distribution have been studied. The activity of complex FeCl₂(PhCH=o-NC₆H₄N=CHPh) with EAO at 200°C is 1.35×10⁵ g oligomers/mol Fe·h, and the selectivity of C_4–10 olefins is 84.8%.     

The efficacy of nitrosonaphthol functionalized XAD-16 resin for the preconcentration/sorption of Ni(II) and Cu(II) ions

Amberlite XAD-16 resin has been functionalized using nitrosonaphthol as a ligand and characterized employing elemental, thermogravimetric analysis and FT-IR spectroscopy. The sorption of Ni(II) and Cu(II) ions onto this functionalized resin is investigated and optimized with respect to the sorptive medium (pH), shaking speed and equilibration time between liquid and solid phases. The monitoring of the influence of diverse ions on the sorption of metal ions has revealed that phosphate, bicarbonate and citrate reduce the sorption up to 10–14%. The sorption data followed Langmuir, Freundlich, and Dubinin–Radushkevich (D–R) isotherms. The Freundlich parameters computed are 1/n = 0.56 ± 0.03 and 0.49 ± 0.05, A = 9.54 ± 1.5 and 6.0 ± 0.5 mmol g⁻¹ for Ni(II) and Cu(II) ions, respectively. D–R isotherm yields the values of X_m = 0.87 ± 0.07 and 0.35 ± 0.05 mmol g⁻¹ and of E = 9.5 ± 0.23 and 12.3 ± 0.6 kJ mol⁻¹ for Ni(II) and Cu(II) ions, respectively. Langmuir characteristic constants estimated are Q = 0.082 ± 0.005 and 0.063 ± 0.003 mmol g⁻¹, b = (4.7 ± 0.2) × 10⁴ and (7.31 ± 0.11) × 10⁴ l mol⁻¹ for Ni(II) and Cu(II) ions, respectively. The variation of sorption with temperature gives thermodynamic quantities of ΔH = −58.9 ± 0.12 and −40.38 ± 0.11 kJ mol⁻¹, ΔS = −183 ± 10 and −130 ± 8 J mol⁻¹ K⁻¹ and ΔG = −4.4 ± 0.09 and −2.06 ± 0.08 kJ mol⁻¹ at 298 K for Ni(II) and Cu(II) ions, respectively. Using kinetic equations, values of intraparticle transport and of first order rate constant have been computed for both the metal ions. The sorption procedure is utilized to preconcentrate these ions prior to their determination in tea, vegetable oil, hydrogenated oil (ghee) and palm oil by atomic absorption spectrometry using direct and standard addition methods.     

Heterogenized polymetallic catalysts: Part III. Catalytic air oxidation of alcohols by Pd(II) complexed to a polyphenylene polymer containing β-di- and tri-ketone surface ligands

This paper describes further studies on mono- and bi-metallic catalysts attached to a polymer support by β-di- and tri-ketone surface ligands. The previous two papers described the oxidation of catechol by the heterogeneous catalysts using Cu(II), Fe(III) and Pd(II) as the metal species. The present study expands these studies to a series of mono- and polyfunctional alcohols using Pd(II) as the metal species. The final catalytic surfaces were prepared by treatment of the modified polymer with a very reactive form of Pd(II), [Pd(CH₃CN)₄]²⁺. The simple alcohols gave increases in rates of up to 5-fold for the bimetallic systems. As might be expected glycols and - -glucose gave even higher increases in rate in going from the mono- to the bi-metallic catalyst. For ethylene glycol the factor was 30. Unsaturated alcohols gave the most dramatic results. With the monometallic catalyst, the products from allyl alcohol consisted of 25% acrolein resulting from direct alcohol oxidation and 75% 3-hydroxypropanal resulting from Wacker-type oxidation of the double bond. With the bimetallic catalyst the overall rate increased by a factor of 10 and the products consisted of 80% acrolein and 20% 3-hydroxypropanal. The actual rate increase for the direct alcohol oxidation is calculated to be a factor of 32. 4-Penten-2-ol and 4-penten-1-ol gave rates that were lower than the monofunctional alcohols. This is attributed to inhibition by olefin π-complex formation with the Pd(II).     

A Novel Screen-Printed and Carbon Paste Electrodes for Potentiometric Determination of Uranyl(II) Ion in Spiked Water Samples

Four new ion-selective electrodes (ISEs) based on poly-(1-4)-2-amino-2-deoxy-β-D-glucan (chitosan) ionophore were constructed for determination of uranyl ion (UO₂(II)) over wide concentration ranges. The linear concentration range for carbon paste electrodes (CPEs) was 1 × 10^–6–1 × 10^–2 mol/L with a detection limit of 1 × 10^–6 mol/L and that for the screen-printed electrode (SPEs) was 1 × 10^–5–1 × 10^–1 mol/L with a detection limit of 8 × 10^–6 mol/L. The slopes of the calibration graphs were 29.90 ± 0.40 and 29.10 ± 0.60 mV/decade for CPEs with dibutylphthalate (DBP) (electrode I) and o-nitrophenyloctylether (o-NPOE) (electrode II) as plasticizers, respectively. Also, the SPEs showed good potentiometric slopes of 29.70 ± 0.30 and 28.20 ± 1.20 mV/decade with DBP (electrode III) and o-NPOE (electrode IV), respectively. The electrodes showed stable and reproducible potential over a period of 54, 62, 101 and 115 days for electrodes I, II, III, and IV, respectively. The electrodes manifested advantages of low resistance, very fast response and, most importantly, good selectivities relative to a wide variety of other cations except Ce(III) ion which interfere seriously. The results obtained compared well with those obtained using atomic absorption spectrometry.     

Cobalt and nickel complexes bearing 2,6-bis (imino) phenoxy ligands: syntheses, structures and oligomerization studies

A series of new cobalt and nickel complexes LMX₂ (M=Co, X=Cl; M=Ni, X=Br) bearing 2, 6-bis(imino)phenoxy ligands were synthesized. The solid-state structures of 1 and 4 have been determined by single-crystal X-ray diffraction study. Treatment of the complexes LMX₂ with methylaluminoxane (MAO) leads to active catalysts for oligomerization of ethylene with catalytic activities in the range of 1.2×10⁵–2.1×10⁵ g mol⁻¹ h⁻¹ atm⁻¹ for Ni complexes, and 10³ g mol⁻¹ h⁻¹ atm⁻¹ for Co complexes. The oligomers were olefins from C₄ to C₁₆.     

Persulphate quenching of the excited state of ruthenium(II) tris-bipyridyl dication: thermal reactions

The rate constant for the reaction between the sulphate radical (SO₄^√−) and the ruthenium (II) tris-bipyridyl dication (Ru(bipy)₃²⁺) is (3.3±0.2)×10⁹ mol⁻¹ dm³ s⁻¹ in 1 mol dm⁻³ H₂SO₄ and (4.9±0.5)×10⁹ mol⁻¹ dm³ s⁻¹ in 0.1 mol dm⁻³, pH 4.7 acetate buffer. The SO₄^√−radical produced by the electron transfer quenching of Ru(bipy)₃^2+* by S₂O₈²⁻ reacts rapidly with both acetate buffer and chloride ions. These side reactions result in a reduction in the overall quantum yield of Ru(bipy)₃³⁺ production and reduced reaction selectivity when Ru(bipy)₃^2+* is quenched by persulphate.     

Interactions of mercury(II), lead(II), calcium(II), aluminium(III) or ferric(III) nitrate with single and double chain linear alkylbenzenesulfonates in aqueous and sea-water media

The solubility products of mercury(II) and lead(II) dodecylbenzenesulfonates were calculated on the basis of light scattering measurements at 20°C to be (9.33 ± 0.90) × 10⁻¹³ and (1.03 ± 0.10) × 10⁻¹² respectively. The investigations of precipitation phenomena performed in diluted natural sea-water ([Cl⁻] = 10⁻¹² mol dm ⁻³), including tenside and added heavy metal ions, showed similar behaviour for all metal dodecylbenzenesulfonates investigated in this work, i.e. the synergistic effect of tenside, of added electrolyte, and of cations and anions from sea-water. A comparison made by a statistical test of significance, chosen to measure agreement between the estimates of the solubility constants obtained in aqueous solutions and in the above mentioned sea-water solution, showed a noticeable effect, evident particularly in the case of mercury(II). The precipitation of tenside and metal nitrates in natural sea-water ([Cl⁻] = 5 × 10⁻¹ mol dm⁻³) covers a wide concentration region of dodecylbenzenesulfonic acid (from high concentrations to 5 × 10⁻⁶ mol dm⁻³) and from high metal nitrate concentrations to very low. The microscopic textures of phases precipitated in the systems with sea-water obviously confirmed favouring formation of the liquid crystalline phase.     

双-β-萘甲酸多缩乙二醇酯在甲醇溶液中分子的构象和分子内激基缔合物的形成

本文研究了双-β-萘甲酸多缩乙二醇酯(P_n)在不同溶剂中的稳态和时间分辨荧光光谱。在甲醇中与在四氢呋喃中不同,P_n显示很强的激基缔合物荧光。表明在甲醇中疏水的两个末端发色团彼此靠近,亲水的多缩乙二醇链段包于两个发色团外部。热力学和动力学研究求出了P_n分子内激基缔合物形成的焓变是-20kJ/mol,活化能为～8.5kJ/mol,激基缔合物形成和离解的速度常数分别为4.5×10⁸s^-1和3.1×10⁸s^-1。     

Cobalt complexes based on dendritic PAMAM bridged salicylaldimine ligands: Synthesis,characterization and performance in ethylene oligomerization

Two novel dendritic poly(amido-amine) (PAMAM) bridged salicylaldimine ligands were synthesized by Schiff base reaction using 1.0 generation dendritic PAMAM as bridged groups. The cobalt complex with 1,4-butanediamine as core (C1) and the cobalt complex with 1,6-hexanediamine as core (C2) based on dendritic PAMAM bridged salicylaldimine ligands were prepared by metallic coordination reaction, respectively. The structures of the ligands and the dendritic cobalt complexes were characterized by fourier transform infrared (FTIR), ultraviolet spectra (UV), hydrogen nuclear magnetic resonance (¹H NMR) and electrospray ionization mass spectra (ESI-MS). The complexes C1 and C2 were evaluated as catalyst precursors for ethylene oligomerization after being activated with methylaluminoxane (MAO), diethylaluminum chloride (Et₂AlCl), ethylaluminium dichloride (EtAlCl₂) and ethylaluminum sesquichloride (EASC). The dendritic cobalt complexes exhibited the highest activity and selectivity for high carbon oligomers with EASC as activator. Under the conditions of 1.0 MPa, 25°C and Al/Co molar ratio 1500, the catalytic activity and selectivity for C₁₀–C₂₀ using C1 were 3.44×10⁶ g·(mol Co·h)^?1 and 76.53% after activation with EASC, and the catalytic activity and selectivity for C₁₀–C₂₀ using C2 were 3.42×10⁶ g·(mol Co·h)^?1 and 84.50%, respectively.     

Vermiculite clay mineral as an effective carbon paste electrode modifier for the preconcentration and voltammetric determination of Hg(II) and Ag(I) ions

A vermiculite modified carbon paste electrode (VMCPE) was employed for the in situ preconcentration of traces of Hg(II) and Ag(I) via an ion-exchange route. Heavy metal ions were accumulated in Britton-Robinson (BR) buffer pH 7 for Hg(II) and pH 6 for Ag(I), and afterwards reduced at –0.7 V vs. Ag/AgCl in the separate measurement solution (BR buffer pH 5 + 0.05 mol/L NaNO₃) prior to the anodic stripping square-wave voltammetric (ASSWV) detection. For Hg(II) ions, at 15 min accumulation, a linear range from 1.0 × 10^–7 to 8.0 × 10^–6 mol/L was obtained, with a 5.7 × 10^–8 mol/L limit of detection. The VMCPE response was linear for Ag(I) ions in the concentration range from 2.0 × 10^–7 to 8.0 × 10^–6 mol/L, at 10 min accumulation with a corresponding limit of detection of 6.3 × 10^–8 mol/L. The relative standard deviation of the analytical procedure including accumulation from a 5 × 10^–7 mol/L solution of Hg (15 min) or Ag(I) (10 min), electrolysis, ASSWV detection, regeneration and activation of the VMCPE, was 4% (n = 6). The optimisation of the parameters for the application of the VMCPE in combination with ASSWV detection is presented and discussed.     

碘鎓盐/胺体系基态和激发态的光谱研究

研究了碘鎓盐与胺在基态和激发态的相互作用,观察到它们形成以鎓盐为电子受体和胺为电子给体的基态和激发态电荷转移络合物。测定了二苯基碘鎓盐和三乙胺形成的络合物组成为1:1分子比,其缔合常数和克分子吸收系数分别为2.2×10mol^-1和2.8×10³mol^-1·1·cm^-1。实验结果表明,随着胺的给电性增加,电荷转移络合物的吸收波长红移,胺的空间体积增大,由于空间障碍,电荷转移络合物的克分子吸收系数下降。