载体对Ni_2P催化剂加氢脱氮反应性能的影响

使用TiO2、Al2O3以及TiO2-Al2O3复合载体考察了载体对磷化镍催化剂活性相和加氢脱氮性能的影响。不同钛铝原子比的TiO2-Al2O3复合载体采用原位-溶胶凝胶法制备,负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备。以喹啉为模型化合物在固定床反应器上对催化剂的加氢脱氮性能进行评价,采用XRD、N2吸附、TEM和H2-TPR等技术对催化剂和载体进行了表征。结果表明,制成的复合载体基本保留了最初引入的γ-Al2O3的孔特征,分散在γ-Al2O3表面的TiO2以锐钛矿晶型存在。不同载体对催化剂的H2还原行为有显著影响,所形成的活性物种也不相同。Al2O3中引入TiO2可以减弱P物种和Al2O3之间的相互作用,有利于Ni2P活性相的生成和催化活性的提高。当Ti/Al的原子比为1∶8时,Ni2P/TiO2-Al2O3催化剂比Ni2P/TiO2、Ni2P/Al2O3催化剂具有更高的加氢脱氮活性。     

由非晶态Ni-P低温制备Ni2P催化剂及其对二苯并噻吩加氢脱硫的催化性能

 以非晶态Ni-P合金为前驱体,在低温下通过PH3处理制备了Ni2P/SiO2-Al2O3催化剂,并用X射线衍射(XRD)、 透射电镜(TEM)、 电感耦合等离子体发射光谱、 N2吸附和X射线光电子能谱(XPS)进行了表征,以二苯并噻吩为探针,在小型连续流动固定床反应器上考察了催化剂的加氢脱硫性能. XRD结果表明,在200～300 ℃范围内前驱体都可以完全转化为Ni2P, 随着磷化温度的升高,晶体结构变得越来越完整. TEM观察发现, Ni-P粒子和Ni2P粒子的平均尺寸都在40～50 nm, 并且都能够高分散在SiO2-Al2O3载体上. XPS结果表明,不论是非负载还是SiO2-Al2O3负载的Ni2P, 表层主要为Ni2P和钝化层Ni3(PO4)2. Ni2P/SiO2-Al2O3催化剂在实验范围内表现出很好的二苯并噻吩加氢脱硫性能.     

TiO2-Al2O3载体的制备及Ni2P/TiO2-Al2O3催化剂上的同时加氢脱硫和加氢脱氮反应

 以溶胶-凝胶法制备的 TiO2-Al2O3 复合氧化物为载体, 采用浸渍法制备了 Ni2P/TiO2-Al2O3 催化剂, 并用 X 射线衍射、N2 吸附脱附、红外和 X 射线光电子能谱等技术对催化剂进行了表征, 考察了载体中 TiO2 含量、焙烧温度及其制备方法对 Ni2P/TiO2-Al2O3 催化剂上同时进行噻吩加氢脱硫和吡啶加氢脱氮反应的影响. 结果表明, 以 Ni/P 摩尔比为 1/2 的前驱体制备的催化剂表面仅出现 Ni2P 物相; 当载体中 TiO2 的含量为 80%, 焙烧温度为 550 oC 时, Ni2P/TiO2-Al2O3 催化剂上加氢脱硫和加氢脱氮的活性最高. 在 360 oC, 3.0 MPa, 氢/油体积比 500, 液时体积空速 2.0 h?1 的条件下, 噻吩和吡啶转化率分别为 61.3%和 64.4%.     

Ni_2P/TiO_2-Al_2O_3催化剂的制备及其加氢脱硫、脱氮性能

采用溶胶-凝胶法制备了TiO2-Al2O3复合载体,采用浸渍法制备了Ni2P/TiO2-Al2O3催化剂,并用X射线衍射(XRD)、N2吸附比表面积(BET)测定、热重-差热分析(TG-DTA)、X射线光电子能谱(XPS)等技术对催化剂的结构和性质进行了表征.催化剂加氢脱硫(HDS)和脱氮(HDN)活性评价在实验室固定床连续反应装置上,以噻吩和吡啶为模型反应物进行.考察了不同载体、Ni2P负载量、标称Ni/P摩尔比、催化剂焙烧温度对Ni2P/TiO2-Al2O3催化剂上同时进行的噻吩加氢脱硫和吡啶加氢脱氮性能的影响.结果表明,TiO2含量为80%(w)的TiO2-Al2O3复合氧化物为载体,Ni2P负载量为30.0%(w),标称Ni/P摩尔比为1/2,催化剂焙烧温度为500℃时,Ni2P/TiO2-Al2O3催化剂加氢脱硫脱氮活性最高.在360℃,3.0MPa,氢油比800(V/V),液时体积空速1.5h-1的条件下,噻吩HDS和吡啶HDN转化率分别为61.32%和64.43%.     

载体孔结构对丁炔二醇二段加氢Ni/γ-Al2O3催化剂加氢性能的影响

以三种不同孔结构的γ-Al2O3为载体,采用等体积浸渍法制备Ni/γ-Al2O3催化剂,经低温氮气吸附、TPR、H2-TPD、XRD、TEM等物性结构表征及丁炔二醇催化合成1,4-丁二醇二段加氢性能评价结果表明,比表面积293m2·g-1、最可几孔径9.4 nm的γ-Al2O3制备的Ni/γ-Al2O3,具有较高的分散度和较多的活性结构中心以及适宜的孔径分布(小于4 nm孔体积分数为12.34%、4～18 nm孔体积分数为64.42%、大于18 nm孔体积分数达23.24%),对丁炔二醇二段加氢表现出较高的加氢活性和稳定性.     

HY/MCM-41/γ-Al2O3负载的硫化态Ni-Mo-P催化剂上萘的加氢

 采用水热法合成了不同SiO2/Al2O3比的MCM-41介孔分子筛. 并分别以HY/MCM-41/γ-Al2O3, HY/γ-Al2O3和γ-Al2O3为载体,用浸渍法制备了Mo-Ni-P催化剂. 以萘为模型化合物,考察了硫化态Mo-Ni-P催化剂的加氢活性. 结果表明,不同载体负载的催化剂催化活性均随着活性组分负载量的增大而提高,其中掺杂大比表面MCM-41的HY/MCM-41/γ-Al2O3所负载的催化剂催化活性提高幅度最大. 由于MCM-41与HY分子筛在酸性和孔结构上存在互补性,因而催化剂对萘加氢存在协同作用. 提出了萘加氢的反应机理,认为反应网络包括两个平行路径: 一是萘加氢生成四氢萘后发生异构化或开环反应; 二是萘加氢生成四氢萘后进一步加氢生成十氢萘,继而发生异构化或开环反应.     

TiO_2-Al_2O_3载体的制备方法对其负载的磷化镍催化剂加氢脱氮反应性能的影响

采用共沉淀法和原位溶胶-凝胶法制备了TiO2-Al2O3复合载体,其负载的磷化镍催化剂采用等体积浸渍法和H2原位还原法制备.通过N2吸附(BET)、X射线衍射(XRD)、透射电镜(TEM)、程序升温还原(TPR),X射线光电子能谱(XPS)和等离子体发射光谱(ICP-AES)表征技术对催化剂进行了表征,并通过喹啉的加氢脱氮反应评价了催化剂的加氢脱氮性能.结果表明,原位溶胶-凝胶法制成的复合载体基本保留了原有的γ-Al2O3的孔特征,具有较大的比表面积和较宽的孔分布,TiO2主要以表面富集的形式分散在管状的γ-Al2O3表面,其负载的磷化镍催化剂还原后所形成的活性相为Ni2P和Ni12P5;而共沉淀法制成的复合载体比表面积较小,孔径分布更加集中,TiO2趋于在块状的Al2O3表面均匀分散,其负载的磷化镍催化剂具有更好的可还原性,还原后所形成的活性相为Ni2P.不同的载体制备方法和不同的钛铝比对催化剂加氢脱氮性能影响较大,当n(Ti)/n(Al)=1/8时,共沉淀法载体负载的催化剂表现出最佳的加氢脱氮性能,在340℃,3 MPa,氢油体积比500,液时空速3 h-1的反应条件下,喹啉的脱氮率可以达到91.3%.     

Ni／ZrO2-Al2O3制备表征及催化性能的研究

本文采用浸渍沉淀法制备了不同配比的ZrO2-Al2O3复合载体。并通过浸渍法制备Ni/ZrO2-Al2O3催化剂,以苯加氢制环己烷反应为探针,考察了ZrO2与Al2O3的配比对Ni催化剂催化加氢性能的影响;采用X射线衍射(XRD)、程序升温还原(TPR)、程序升温脱附(TPD)等技术考察复合载体对Ni催化剂的体相结构、还原性能以及表面吸附性能的影响。研究结果表明,ZrO2质量分数为20%的复合载体所负载的Ni催化剂有很好的加氢活性,优于单组分载体负载的Ni催化剂;采用浸渍沉淀法制备的ZrO2-Al2O3复合载体中ZrO2以非晶态形式存在,这是由于Al2O3的存在影响了ZrO2的内部结构;该载体负载的Ni催化剂较其他催化剂更容易被还原,吸附中心数量增加。     

镍盐前体对Ni/γ-Al2O3催化剂催化加氢活性的影响

用X射线衍射、紫外-可见漫反射光谱、程序升温还原、CO化学吸附和微反应测试等方法研究了不同镍盐前体制备的负载型Ni/γ-Al2O3催化剂的结构和催化α-蒎烯加氢活性.结果表明,用醋酸镍前体制备的催化剂的催化加氢活性远高于用硝酸镍前体制备的催化剂,并且这种催化加氢活性的差异与不同前体制备的Ni O/γ-Al2O3样品表面Ni2 的分散状态及还原度密切相关.当Ni2 负载量远低于其在γ-Al2O3载体表面上的分散容量时,Ni2 优先嵌入载体表面四面体空位,随着Ni2 负载量的增加,嵌入载体表面八面体空位的Ni2 的比例增大.由于醋酸根阴离子对γ-Al2O3载体表面四面体空位的屏蔽效应大于硝酸根阴离子,在醋酸镍前体制备的Ni O/γ-Al2O3样品表面,Ni2 倾向于嵌入载体表面八面体空位且易被还原为金属态Ni0,故用醋酸镍前体制备的Ni/γ-Al2O3催化剂的催化α-蒎烯加氢活性高于用硝酸镍前体制备的催化剂.     

Ni/SiO2-Al2O3催化剂在水相加氢体系中的活性及稳定性研究

采用浸渍法制备了不同Si含量的Ni/SiO2-Al2O3催化剂,通过吡啶-原位傅里叶变换红外(Py-FTIR)、X射线衍射(XRD)、低温N2物理吸附(N2Physisorption)、H2-程序升温还原(H2-TPR)等技术对催化剂进行了表征,并考察了催化剂在水相1,4-丁炔二醇加氢反应中的活性和稳定性.结果表明:SiO2的引入覆盖了部分γ-Al2O3表面,使暴露的Al3+减少,载体表现出部分SiO2的表面性质.随Si含量的增加,Ni/SiO2-Al2O3催化剂初始活性下降,产生这一现象的原因是引入SiO2使活性组分Ni与载体之间相互作用减弱,导致活性组分Ni迁移聚集,且催化剂的孔容和孔径减小.同时,SiO2显著抑制了γ-Al2O3的水合,催化剂的使用稳定性随Si含量的增加而提高.当Si含量为3%时,催化剂的初始活性下降幅度较小,且催化剂的水热稳定性显著提高,表现出最佳的反应性能.     

Homopolymerization of 2-alkyl- and 2-aryl-2-oxazolines

2-Aryl- and 2-alkyl-2-oxazolines have been polymerized to poly-(N-aroyl)aziridines and poly(N-acyl)aziridines, respectively, in the presence of boron trifluoride. The polymers obtained were glassy, light yellow resins with molecular weights ranging from 3500 to 7500 (35–50 oxazoline units per chain). The polymerization rates have been determined for several of these monomers. A polymerization mechanism is proposed.     

Structure and properties of single crystalline CaMg2Bi2, EuMg2Bi2, and YbMg2Bi2

Single crystals of CaMg(2)Bi(2), EuMg(2)Bi(2), and YbMg(2)Bi(2) were obtained from a Mg-Bi flux cooled to 650 °C. These materials crystallize in the CaAl(2)Si(2) structure-type (P ?3m1, No. 164), and crystal structures are reported from refinements of single crystal and powder X-ray diffraction data. EuMg(2)Bi(2) displays an antiferromagnetic transition near 7 K, which is observed via electrical resistivity, magnetization, and specific heat capacity measurements. Magnetization measurements on YbMg(2)Bi(2) reveal a weak diamagnetic moment consistent with divalent Yb. Despite charge-balanced empirical formulas, all three compounds are p-type conductors with Hall carrier concentrations of 2.0(3) × 10(19) cm(-3) for CaMg(2)Bi(2), 1.7(1) × 10(19) cm(-3) for EuMg(2)Bi(2), and 4.6(7) × 10(19) cm(-3) for YbMg(2)Bi(2), which are independent of temperature to 5 K. The electrical resistivity decreases with decreasing temperature and the resistivity ratios ρ(300 K)/ρ(10 K) ≤ 1.6 in all cases, indicating significant defect scattering.     

Redetermination of NaGdS2, NaLuS2 and NaYS2

The title structures NaGdS₂ (sodium gadolinium sulfide), NaLuS₂ (sodium lutetium sulfide) and NaYS₂ (sodium yttrium sulfide) were redetermined in order to improve the structural information available for the family of group 1 and thallium rare earth sulfides, which are isostructural with the rhombohedral α‐NaFeO₂ structure type. In particular, the present investigation has been directed at the rhombohedral sodium rare earth sulfides. The observed dependence of the fractional coordinate z(S²⁻) on the identity of the rare earth element in the newly determined structures is in agreement with the known structures of the potassium and rubidium analogues. Crystals of NaGdS₂ and NaLuS₂ display obverse–reverse twinning.     

Rh2CO2/Al2O3上H2吸附及CO和H2共吸附

CO加氢反应机理一直是许多化学工作者感兴趣的课题．Rh催化剂因其优良的性能而被用于 CO加氢机理研     

Synthesis and reactions of 2-chloro- and 2-tosyloxy-2'-deoxyinosine derivatives

Convenient syntheses of 2-chloro- and 2-tosyloxy-2'-deoxyinosine as their tert-butyldimethylsilyl ethers are described. Both compounds can be synthesized via a common route and rely on commercially available 2'-deoxyguanosine. The present method leading to the chloro nucleoside is operationally simpler compared to previously reported glycosylation techniques where isomeric products were obtained. Both electrophilic nucleosides can be used for the preparation of N-substituted 2'-deoxyguanosine analogues via displacement of the leaving groups, and a comparison of their reactivities shows the chloro analogue to be superior. Interestingly, a Pd catalyst-mediated, two-step, one-pot conversion of an allyl-protected chloro nucleoside intermediate to the final modified 2'-deoxyguanosine derivatives is also feasible. On the basis of these observations, initial assessments of Pd-catalyzed aryl amination as well as a C-C cross-coupling have also been performed with the chloro and tosyloxy nucleoside substrates. Results indicate a potentially high synthetic utility of 2-chloro-2'-deoxyinosine and in many instances this derivative can supplant the bromo and fluoro analogues that are more cumbersome to prepare or are not readily available.     

Enthalpies of combustion and formation of 2-acetylpyrrole, 2-acetylfuran and 2-acetylthiophene

The combustion energies for 2-acetylpyrrole (cr) and 2-acetylfuran (cr) were determined using a static bomb calorimeter, whereas the combustion energy of 2-acetylthiophene (l) was determined with a rotating bomb calorimeter; both calorimeters have been recently described. The molar combustion energies obtained were: −(3196.1 ± 0.6) kJ mol⁻¹ for 2-acetylpyrrole, −(2933.8 ± 0.7) kJ mol⁻¹ for 2-acetylfuran, and −(3690.4 ± 0.8) kJ mol⁻¹ for 2-acetylthiophene. From these combustion energy values, the standard molar enthalpies of formation in the condensate phase were obtained as: −(163.51 ± 0.97) kJ mol⁻¹, −(283.50 ± 1.06) kJ mol⁻¹ and −(123.93 ± 1.15) kJ mol⁻¹, respectively. The obtained values of combustion and formation enthalpies of 2-acetylthiophene are in concordance with the reported previously. For the two last compounds, polyethene bags were used as an auxiliary material in the combustion experiments. The heat capacities and purities of the compounds were determined using a differential scanning calorimeter.     

Sc2MgGa2 and Y2MgGa2

Scandium magnesium gallide, Sc₂MgGa₂, and yttrium magnesium gallide, Y₂MgGa₂, were synthesized from the corresponding elements by heating under an argon atmosphere in an induction furnace. These intermetallic compounds crystallize in the tetragonal Mo₂FeB₂‐type structure. All three crystallographically unique atoms occupy special positions and the site symmetries of (Sc/Y, Ga) and Mg are m2m and 4/m, respectively. The coordinations around Sc/Y, Mg and Ga are pentagonal (Sc/Y), tetragonal (Mg) and triangular (Ga) prisms, with four (Mg) or three (Ga) additional capping atoms leading to the coordination numbers [10], [8+4] and [6+3], respectively. The crystal structure of Sc₂MgGa₂ was determined from single‐crystal diffraction intensities and the isostructural Y₂MgGa₂ was identified from powder diffraction data.     

Reactions of 2-amino- and 2-hydrazinobenzimidazoles with 2-acyldimedones

The reaction of 2 formyldimedone with 2-amino- and 2-hydrazinobenzimidazoles at 20°C in ethanol gave 2-(2-benzimidazolyl)aminomethylene- and 2-[2-(2-benzimidazolyl)hydrazinomethylene]-5,5-dimethylcylohex-anediones, while this reaction carried out in ethanol at reflux in the presence of acid gave 2,2-dimethyl-4-oxo 1, 2, 3, 4-tetrahydroquinazolino(1, 2-a]benzimidazole and 1-(2-benzimidazolyl)-6, 6-dimethyl-4-oxo-4, S, 6, 7-tetrahydroindazole, respectively.Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 2, pp. 247–252, February, 1996.