共查询到20条相似文献,搜索用时 140 毫秒
1.
2.
3.
酸功能化离子液体催化合成柠檬酸三丁酯 总被引:2,自引:0,他引:2
合成并表征了酸功能化离子液体,用于催化合成柠檬酸三丁酯(TBC).通过考察各种离子液体的催化活性及重复使用性能,选定酸功能化离子液体[HSO3-pmim]HSO4为催化合成TBC的催化剂.研究了催化剂用量、醇酸摩尔比、反应时间等因素对酯化反应的影响,得到其较佳工艺条件为:催化剂用量为反应物总质量的8·0%,醇酸摩尔比为5·5∶1,反应温度110~150℃,反应时间3h.此条件下,酯化率达到99·0%.分离出的离子液体未经任何处理重复使用8次后,酯化率仍为95·2%. 相似文献
4.
固载杂多酸SiW_(12)/C催化合成富马酸二甲酯 总被引:10,自引:4,他引:6
用自制的固体杂多酸催化剂SiW12 /C进行催化酯化合成富马酸二甲酯 (DMF) .探讨了催化剂用量、醇 /酸比、反应时间、反应温度等动力学条件对合成DMF的影响 .确定了合成DMF的最佳合成工艺条件 :醇 /酸物质的量比为 6∶1,催化剂用量为富马酸质量的 2 .5 % ,反应时间 7.0h ,反应温度为回流温度 ,酯化率可达 90 .6 % .结果表明 ,该催化剂催化活性高 ,可重复使用 ,后处理容易 ,生产成本低且无三废污染 . 相似文献
5.
《有机化学》2016,(5)
以价格低廉的苯并噻唑为原料,合成了4种新型功能化布朗斯特酸性离子液体:苯并噻唑硫酸氢盐([HBth]-HSO_4)、苯并噻唑磷酸二氢盐([HBth]H_2PO_4)、苯并噻唑高氯酸盐([HBth]ClO_4)、苯并噻唑硝酸盐([HBth]NO_3),其结构经FT-IR、HRMS、NMR表征得到确认.考察了4种酸性离子液体在蓖麻油酸和乙二醇丁醚(EGBE)酯化反应中的催化活性,并与以浓硫酸为催化剂的催化体系相对照.结果表明:当n(蓖麻油酸)∶n(乙二醇丁醚)=1∶1.15,离子液体催化剂用量为蓖麻油酸重量的2%,反应温度90℃,反应时间5 h,酯化率可达98.8%,离子液体催化剂经真空干燥重复使用10次后,仍具有较高的催化活性.还考察了以苯并噻唑硫酸氢盐为催化剂催化合成系列蓖麻油酸二元醇醚酯和短链脂肪酸酯,也获得了较高的酯化率,且离子液体均能与酯产物自动分相.与传统硫酸催化酯化相比,此类离子液体催化酯化具有生产成本低、过程清洁、使用周期长等优点,完全可以替代传统浓硫酸催化蓖麻油酸酯化反应. 相似文献
6.
ZnMn2O4纳米催化剂制备及催化合成乙酸正丁酯 总被引:4,自引:0,他引:4
本文以共沉淀法制备了四方晶系锌锰复合氧化物ZnMn2O4纳米催化剂。采用X射线粉末衍射(XRD)和透射电子显微镜(TEM)测试技术对样品进行了分析表征,结果表明所合成的催化剂为粒径均匀的纳米粒子,平均粒径在20-50 nm,具有较好的分散性。实验考察了所制备的ZnMn2O4纳米催化剂对乙酸和正丁醇酯化反应的催化活性,表明ZnMn2O4对乙酸正丁酯的合成有较高的催化活性;探讨了催化剂焙烧温度、催化剂用量、酸醇摩尔比以及反应时间对酯化率的影响,确定了适宜的酯化反应条件,以焙烧温度为300 ℃制备的ZnMn2O4为催化剂,在催化剂用量为0.3%(以反应物总质量计)、酸醇摩尔比n(酸):n(醇)=1.8:1、反应时间为4 h、酯化反应温度120 ℃的条件下,酯化率可达92.53%。 相似文献
7.
8.
9.
10.
制备了一系列脱铝超稳Y沸石(DUSY)负载的12-磷钨杂多酸(PW)及其铯盐催化剂, 表征了其比表面和酸强度, 并在乙酸和正丁醇液相酯化反应中考察了催化剂的活性、选择性和稳定性. 结果表明, DUSY上引入PW后, 酯化反应的催化活性明显提高, 正丁醇的转化率从49.5%上升到86.4%, 而PW的这种促进作用并未在超稳Y沸石负载的PW催化剂上观察到; DUSY负载磷钨酸铯盐催化剂(Cs2.5H0.5PW/DUSY)的转化率高达94.6%, 且乙酸正丁酯的选择性为100%; 催化剂稳定性考察表明, 经过5次反复使用后, 负载磷钨酸铯盐的催化活性仍高达81.6%, 而相应的负载磷钨酸的催化活性却大幅度下降到47.6%; 催化剂溶脱性研究表明, 催化剂在反复使用过程中活性下降的量与活性组分在极性体系中的溶脱量成对应关系, 说明催化剂活性下降的主要原因是杂多酸(盐)活性组分的流失造成的, 而负载磷钨酸铯盐良好的催化稳定性来源于磷钨酸铯盐的难溶脱性. 相似文献
11.
新型磷钨酸基固体酸催化油酸酯化合成生物柴油 《燃料化学学报》2017,45(3):303-310
利用磷钨酸(PTA)与1,2,3-三氮唑-4,5-二羧酸(TDA)在水溶液中的反应,合成了一种新的固体酸TDA-PTA,采用X射线粉末衍射(XRD)、扫描电镜(SEM)、红外光谱(FT-IR)、热重(TG)以及电位滴定等方法对其进行了表征,并以油酸与甲醇的酯化反应为探针反应,考察了其催化性能,探讨了催化剂用量、醇酸物质的量比、反应时间、反应温度以及催化剂重复利用次数等对产物收率的影响。结果表明,TDA-PTA不仅保留有磷钨酸典型的Keggin结构,而且具有较强的酸强度;经修饰后,催化剂具有规整的球形形貌,比表面积明显大于磷钨酸;TDA-PTA在油酸与甲醇的酯化反应中表现出了优良的催化活性,尤其显示出好的重复利用性,六次使用后,仍得到86.8%的油酸甲酯产率,催化剂的物相以及Keggin结构没有明显变化。 相似文献
12.
13.
磁性纳米固体超强酸的合成、表征及性能 总被引:16,自引:0,他引:16
首次制备了SO4^2-/Co0.5Fe2.5O4^-ZrO2磁性固体超强酸,利用TEM,DTA,XRD和FTIR等手段研究了Co0.5Fe2.5O4磁性基质对ZrO2的粒子大小、晶化温度与结构的影响,考察了磁性固体超强酸的催化性能及催化剂的寿命、回收率和磁性,结果表明,引入Co0.5Fe2.5O4磁性基质不但赋予催化剂以磁性,而且在固体超强酸形成过程中延迟了ZrO2由四方晶相向单斜晶相的转变,有助于稳定样品表面的含硫物种,磁性固体超强酸对酯化反应具有较高的催化活性,可活化再生,并保持磁性。 相似文献
14.
离子交换树脂固载SnCl4:合成,表征和酯化反应 总被引:2,自引:0,他引:2
均相催化剂的固载化,由于具有独特属性,近年来发展很快.我们在用高分于材料固载路易斯酸的研究中,发现固载在离子交换树脂的路易斯酸催化性能非常稳定.本文将空气中强烈水解,且腐蚀性很强的四氯化锡与大孔苯乙烯系阳离子交换树脂反应,首次合成了离了交换树脂四氯化锡复合物(以下简写成压IER·SnCl_4),并对IER·SnCl_4的IR、UV光谱性质及在酯化反应中的催化性能进行了研究.结果表明IER·SnCl_4不仅活性高,而且在重复使用性能上表现了突出特点,显示了良好的应用前景. 相似文献
15.
A polystyrene-bonded stannic chloride catalyst was synthesized by the method of lithium polystyryl combined with stannic chloride. This catalyst is a polymeric organometallic compound containing 0.25 mmol Sn (Ⅳ)/g catalyst. The catalyst showed sufficient stability and catalytic activity in organic reaction such as esterification, acetalation and ketal formation, and it could be reused many times without losing its catalytic activity. 相似文献
16.
氨基磺酸对酯化反应的催化作用 总被引:4,自引:0,他引:4
氨基磺酸对酯化反应的催化作用张竞清,刘间生(佛山大学化学系佛山528000)关键词氨基磺酸,催化,酯化,乙酸正丁酯氨基磺酸H2NSO3H是一种高稳定性、不吸湿的固体酸[1]。主要用作金属表面处理剂,合金电镀添加剂,织物染色助剂以及硬表面清洗剂等[2]... 相似文献
17.
12-Tungstophosphoric acid supported onto silica was synthesized by impregnation. The supports and synthesized catalysts were
characterized for chemical stability, ion exchange capacity, thermogravimetric analysis, differential scanning calorimetry,
FT-IR, and BET surface area. The catalytic activity was evaluated for liquid phase esterification reactions. The catalyst
was regenerated and reused. The best catalyst was calcined at different temperatures and its catalytic activity was also evaluated
for esterification reactions under optimized conditions. Further, obtained results are compared with l2-tungstophosphoric
acid supported onto zirconia in order to see effect of acidic nature of support on catalytic activity as well as thermal stability
of the catalyst. 相似文献
18.
《Comptes Rendus Chimie》2017,20(8):818-826
An efficient heterogeneous acid catalyst was developed using cenospheres, a byproduct of coal-fired thermal power plants by the method of wet impregnation. Catalyst characterization was carried out using various analytical techniques, namely, Fourier transform infrared, X-ray diffraction, field emission gun scanning electron microscopy and Brunauer–Emmett–Teller surface area and surface acidity analysis. The characterization revealed the excellent catalytic activity of the catalyst for the esterification reaction of n-octanol and acetic acid. Various reaction parameters, namely, catalyst loading, a molar ratio of alcohol/acid and reaction temperature were evaluated and optimized by response surface methodology using the Box–Behnken model. The response surface methodology model equations corresponding to the conversion of acid and % yield of ester were developed. The model well predicted the optimal reaction conditions, which were validated experimentally with good agreement. The excellent catalytic performance was observed in the esterification reaction with high conversion of acid (95.34%) and high yield of n-octyl acetate (94.81%). Reusability study of the catalyst showed that the catalyst could be used efficiently up to three reaction cycles. This study explores the use of cenospheres to prepare a solid acid catalyst for the industrially important esterification reactions. 相似文献
19.
20.
Nano sulfated titania was tested as catalyst for esterification of free fatty acids, specially methanolic and ethanolic esterification of stearic acid (biodiesels). Factorial design evidenced a positive effect of reaction temperature, amount of catalyst, and solvents on ester conversion. This nano-sized sulfated titania has been prepared by a sol-gel hydrothermal process. This prepared sulfated titania showed high catalytic activity in direct esterification of fatty acids as well as benzoic acids with various alcohols and phenols under solvent-free conditions. This method is of great value because of its environmentally benign character, easy handling, high yields, convenient operation, and green. FT-IR studies are shown that the catalyst can be reused for acylation without loss of catalytic activity. 相似文献