Analysis of oligomeric and monomeric carbohydrates from hydrothermal degradation of cotton-waste materials using HPLC and GPC

Summary The hydrolysis of different cotton materials under hydrothermal conditions was investigated. For the analysis of the resulting reaction products high-performance liquid chromatography and gel-permeation chromatography were applied. HPLC columns with ion exchange materials as stationary phases (HPX 87P and Shodex S801) enabled the separation of monomeric sugars and degradation products. Oligomeric sugars were analyzed using a gel column (Bio-Gel P-2) as well as a HPLC column (HPX 42A). Through identification of additional reaction products the mass balance of the hydrolysis can be improved and the analysis of the distribution of the oligomeric sugars gives information for the selection of the reaction conditions.     

New analytical possibilities of amperometric detection in high-performance liquid chromatography

It is demonstrated that sugars can be determined with high sensitivity by high-performance liquid chromatography (HPLC) with amperometric detection using domestic instruments. Optimal conditions of the detection of catecholamines were selected; obtained detection limits provide the determination of these compounds in biological fluids. Conditions of the simultaneous separation of most familiar narcotics by HPLC on one column with high precision and low detection limit were optimized. Presented at the V All-Russian Conference with the Participation of CIS Countries on Electrochemical Methods of Analysis (EMA-99), Moscow, December 6–8, 1999.     

Analysis of formose sugar and formaldehyde by high-performance liquid chromatography

Formose sugar and formaldehyde (HCHO) were analyzed using high-performance liquid chromatography (HPLC) utilizing a CarboPac PA1 column (Dionex) and pulsed amperometric detection. This HPLC system was unsuitable for the analysis of formose sugar and HCHO and thus reducing sugars and unconverted HCHO were determined by endowing them with charges through a derivatization method using 2,4-dinitrophenylhydrazine. The separation and detection of compounds were performed by three Chromolith RP-C18 columns (Merck) and diode array detection, at a wavelength of 360 nm ultraviolet light, respectively. Lower sugars (except HCHO) showed some instabilities when the derivatized samples were kept for the extended periods of time. For C₅ and consecutive higher sugars, a certain derivatization time was necessary. In the present case (formose reaction with partial HCHO conversion), approximately 18 h may be a reasonable compromise for the derivatization reaction. A derivatization agent to compound mole ratio of up to 100:1 was required to complete the derivatization of C₄ and higher sugars. However, the analysis of C₄ and consecutive higher sugars is problematic for example due to overlapping of peaks or branched-chain sugars.     

Amperometric Determination of Sugars at Activated Barrel Plating Nickel Electrodes

We report amperometric determination of sugars by using a disposable barrel plating nickel electrode (Ni‐BPE) in this study. The activated Ni‐BPE possesses good reproducibility in flow injection analysis of sugars with a relative standard deviation of 3.16% for 10 consecutive injections of glucose. The electrocatalytic mechanism for the detection of sugars as well as the use as a detector in high‐performance liquid chromatography (HPLC) is investigated. We achieve a good separation of four sugars (glucose, fructose, sucrose, and maltose) in HPLC with favorable sensitivity at a detection potential of +0.55 V vs. Ag/AgCl. The results of wide linear calibration ranges and detection limits in the μM range meet the need of real sample analysis. This detection method is successfully used for quantitative determination of sugars in honey to identify its authentication.     

Development of a method for fast analysis of phenolic molecular markers in biomass burning particles using high performance liquid chromatography/atmospheric pressure chemical ionisation mass spectrometry

A high performance liquid chromatography/atmospheric pressure chemical ionisation mass spectrometry (HPLC/APCI-MS) method for the fast analysis of 21 biomass burning tracers in particles samples has been developed. Separation was done with a Zorbax SB-C18 Rapid Resolution cartridge column (4.6 mm x 30 mm x 3.5 microm), using a CH3OH/H2O/CH3COOH gradient at a flow rate of 0.5 mL/min. The observed relative standard deviations (RSD) for the retention times and peak areas were <0.6 and <15%, respectively. With the short analytical column and the sensitive detector the total analysis time for the standard mixture was reduced to 15 min. Instrumental detection limits were <1 microM (S/N=3) for all standard compounds except homovanillic acid (4.3 microM). The suitability of the developed method for the analysis of biomass burning particles is demonstrated by the measurements of five different real biomass burning samples. The results of these measurements showed clear differences between the different kinds of biomass and they are in good agreement with results from earlier studies in the literature.     

A Quarter Century of Thin-Layer Chromatography—An Interim Report

Thin-layer chromatography (TLC) has been in general use since 1958. The prerequisites were the use of very small particle size material in the layers and the demonstration that not only lipophilic mixtures but also mixtures of cardiac glycosides, alkaloids, sugars, and amino acids could be separated quickly and simply on silica gel layers. The impressive separations obtained using the method later encouraged attempts to use adsorbants having such, narrow-range small particles in column chromatography. In order to achieve sufficient flow rates the use of high pressures was necessary. Thus, high pressure or high performance liquid chromatography (HPLC) was born, whose godfather, as far as instrumental development is concerned, was gas chromatography (GC). Today, chromatography is classified according to the nature of the transport phase: liquid, gas, or “electro” chromatography. Sample preparation often requires more time than the actual separation. rapid thermal separation and application techniques (TAS, TFG) have brought advantages to TLC. As before, the art of chromatography consists in choosing the appropriate mobile phase, stationary phase, and separation technique. Gradient TLC offers new possibilities; for example, gradient layers make it possible to obtain selective information on the individual components of a mixture and also allow significant focussing effects to be achieved. Sequential and centrifugal TLC have paved the way for further advances. The questions arise whether the standard conditions, formulated 25 years ago, are still applicable and how the variations which have been introduced should be judged. Group- and substance specific methods of detection are discussed in addition to universal methods. Quantitation is critically discussed and it is concluded that HPLC has the better chance in the furture. Combination and coupling techniques ease the positive identification of individual substances. Finally, it is discussed why TLC is the simplest, most versatile, most cost effective, and most widely used chromatographic method and reasons are proposed as to why it will remain so for the foreseeable future.     

Determination of levoglucosan in atmospheric aerosols using high performance liquid chromatography with aerosol charge detection

A sensitive method for analysis of levoglucosan (1,6-anhydro-beta,d-glucopyranose) and other monosaccharide anhydrides, compounds present in biomass combustion smoke, was investigated employing high-performance liquid chromatography (HPLC) with recently developed aerosol charge detection. Aerosol charge detection involves the conversion of the column effluent to an aerosol, which is charged to produce a current. Use of a cation-exchange column and a pure water eluent was found to separate levoglucosan and mannosan from other aerosol components with a detection limit of about 90 ng mL(-1) for levoglucosan or 5 ng injected. This method was demonstrated by successful analysis of aerosol filter samples from three locations.     

Fourier transform infrared quantification of sugars in pretreated biomass liquors

The process of converting renewable lignocellulosic biomass to ethanol requires a number of steps, and pretreatment is one of the most important. Pretreatment usually in volves a hydrolysis of the easily hydrolyzed hemicellulosic component of biomass using some form of thermal/chemical/mechanical action that results in a product that can be further hydrolyzed by cellulase enzymes (the cellulosic portion). The sugars produced can then befermented to ethanol by fermentative microorganisms. If the pretreatment step is not severe enough, the resultant residue is not as easily hydrolyzed by the cellulase enzyme. More severe pretreatment conditions result in the production of degradation products that are toxic to the fermentative microorgan ism. In this article, wereport the quantitative analysis of glucose, mannose, xylose, and acetic acid using Fourier transform infrared (FTIR) spectroscopy on liquors from dilute-acid-pretreated softwood and hard wood slurries. Comparison of FTIR and high-performance liquid chromatography quantitative analyses of these liquorsare reported. Recent developments in infrared probe technology has enabled the rapid quantification of these sugars by FTIR spectroscopy in the batch reactor during optimization of the pretreatment conditions, or interfaced to the computer controlling a continuous reactor for on-line monitoring and control.     

Immobilized artificial membrane chromatography with mass spectrometric detection: a rapid method for screening drug-membrane interactions.

A high-performance liquid chromatography (HPLC)/electrospray ionization mass spectrometry method for measuring drug-membrane interactions was developed using immobilized artificial membrane (IAM) fast-screening mini-columns. The HPLC mobile phase consisted of phosphate-buffered saline (i.e., 5.0 mM phosphate buffer at pH 7.4, 1.35 mM KCl, and 68.5 mM NaCl) and acetonitrile. This method facilitated the measurement of IAM retention time of over ten compounds in one experiment, significantly reducing analysis time compared with the earlier IAM-HPLC method. The particular electrospray source used demonstrated the ability to tolerate the high salt-containing nonvolatile buffer used for retention time measurement.     

Analysis of flavonol aglycones and terpenelactones in Ginkgo biloba extract: A comparison of high-performance thin-layer chromatography and column high-performance liquid chromatography

Advancements in automated high-performance thin-layer chromatography (HPTLC) have made it feasible to assess its use for the quantitative analysis of marker compounds in botanical preparations. We report here the findings of method comparisons for the terpenelactones and flavonol aglycones by column high-performance liquid chromatography (HPLC) with evaporative light scattering and UV detection, and HPTLC with a scanning densitometer. For the HPTLC assay of terpenelactones, total bilobalide, ginkgolide A, and ginkgolide B consistently achieved <70% of the total determined using HPLC, regardless of variations to postchromatographic derivatization time and temperature. Accuracy testing showed the possibility of a matrix interference. In contrast, a good relationship (95%) was determined between HPTLC and HPLC for determination of total flavonol glycosides (calculated from combined quercetin, kaempferol, and isorhamnetin) from an acid-hydrolyzed Ginkgo biloba L. (GBE) sample. The HPTLC flavonol aglycone method also performed well in terms of accuracy (overall average of 96% recovery for the 3 aglycones) and consecutive plate repeatability (overall percent relative standard deviation of 4.4). It is demonstrated that HPTLC can be a time-saving complement to HPLC for routine analysis of the flavonol glycosides in GBE.     

Linkage and branch determination of N-linked oligosaccharides using sequential degradation/closed-ring chromophore labeling/negative ion trap mass spectrometry

A method based on sequential degradation, p-aminobenzoic ethyl ester (ABEE) closed-ring labeling, and negative ion electrospray ionization tandem mass spectrometry is presented for the study of linkage and branch determination for N-linked oligosaccharides. Closed-ring labeling provides greater linkage information than the more popular open-ring reductive amination approach. In addition, after high-performance liquid chromatography (HPLC) separation, closed-ring labeling allows for regeneration of the underivatized oligosaccharide, a requirement for alkaline sequential degradation. The analytical scheme presented here uses HPLC separation of closed-ring labeled oligosaccharides to resolve the mixture into individual forms that undergo subsequent structural analysis by negative ion tandem mass spectrometry. To facilitate complete structural analysis, particularly for larger sugars, the closed-ring labels are removed and the sugars are sequentially degraded by controlled alkaline hydrolysis. It is noteworthy that for sugars containing sialic acid moieties, a protecting group must be used to stabilize sialic acid groups during sequential alkaline degradation. This described approach was applied to two high mannose oligosaccharides M5G2, M6G2 cleaved from the ribonuclease B and a complex oligosaccharide A2 cleaved from transferrin.     

A Simplified Filter Paper Assay Method of Cellulase Enzymes Based on HPLC Analysis

A simplified filter paper assay (FPA) method of cellulase enzymes was proposed based on high-performance liquid chromatography (HPLC) measurement. The method was according to the sum of glucose and cellobiose concentrations measured by HPLC that was able to be correlated with filter paper units (FPU) of the cellulase enzymes assayed by the traditional FPA method, regardless of the differences in the sources, activities, and components of the cellulases. This simple and quick assay method for the cellulase enzymes provided another parameter of the ratio of glucose to cellobiose (G/C ratio) representing the capacity of cellulase enzymes degrading cellulose into fermentable monomeric sugars.     

Screening for anthocyanins using high-performance liquid chromatography coupled to electrospray ionization tandem mass spectrometry with precursor-ion analysis, product-ion analysis, common-neutral-loss analysis, and selected reaction monitoring

A systematic method for anthocyanin identification using tandems mass spectrometry (MS/MS) coupled to high-performance liquid chromatography (HPLC) with photo-diode array detection (PDA) was developed. Scan for the precursor ions of commonly found anthocyanidins (cyanidin, delphinidin, malvidin, pelargonidin, petunidin, and peonidin) using LC/MS/MS on a triple quadrupole instrument allows for the specific determination of each category of anthocyanins. Further characterization of each anthocyanin was performed using MS/MS product-ion analysis, common-neutral-loss analysis, and selected reaction monitoring (SRM). The method was demonstrated for analysis of anthocyanins in black raspberries, red raspberries, highbush blueberries, and grapes (Vitis vinifera). Previous reported anthocyanins in black raspberries and red raspberries are confirmed and characterized. Common-neutral-loss analysis allows for the distinction of anthocyanin glucosides or galactoside and arabinosides in highbush blueberries. Separation and identification of anthocyanin glucosides and galactosides were achieved by LC/MS/MS using SRM. Anthocyanin isomers such as cyanidin sophoroside and 3,5-diglucoside were differentiated by their fragmentation pattern during product-ion analysis. Fifteen anthocyanins (all possible combinations of five anthocyanidins and three sugars) were characterized in highbush blueberries. Pelargonidin 3-glucoside and pelargonidin 3,5-diglucoside were detected and characterized for the first time in grapes. The present approach allows mass spectrometry to be used as a highly selective detector for rapid identification and characterization of anthocyanins and can be used as a sensitive procedure for screening anthocyanins in fruits and vegetables.     

Determination of aliphatic alcohols after on-line microwave-assisted derivatization by liquid chromatography-photodiode array detection

In this study, high-performance liquid chromatography (HPLC) in conjunction with continuous derivatization for the determination of aliphatic and polyethoxylated alcohol is reported. Reaction of alcohol group with phenyl isocyanate or benzyl chloride reagents assisted with microwaves (MW) irradiation is carried out in an on-line system coupled to HPLC with photodiode array detection (PDA). Reactor was placed into a microwave oven at 450 W. The flow rate, reagent amounts, irradiation time, and chromatographic conditions were optimized. The continuous analysis using the system MW-HPLC-PDA provided high sensitivity, reduce the amount of reagents and analysis time. This proposed method can be used for the analysis of commercial alcohol polyethoxylated mixture.     

High Temperature Interaction Chromatography of Olefin Copolymers

Summary: The synthesis and characterization of polyolefins continues to be one of the most important areas for academic and industrial polymer research. One consequence of the development of new “tailor-made” polyolefins is the need for new and improved analytical techniques for the analysis of polyolefins with respect to molar mass and chemical composition distribution. The present article briefly reviews different new and relevant chromatographic techniques for polyolefin analysis. For the fast analysis of the chemical composition distribution of polyolefins a new high-temperature gradient high-performance liquid chromatography (HPLC) system has been introduced. The efficiency of this system for the separation of various olefin copolymers is demonstrated. The correlation between elution volume and chemical composition can be accessed by on-line coupling of high temperature HPLC with FTIR spectroscopy. For the elucidation of the chemical composition as a function of molar mass high-temperature size exclusion chromatography and ¹H-NMR spectroscopy can be coupled. It is shown that the on-line NMR analysis of chromatographic fractions yields information on microstructure and chemical composition in addition to molar mass distribution.     

Hybridation of different chiral separation techniques with ICP-MS detection for the separation and determination of selenomethionine enantiomers: chiral speciation of selenized yeast

Enantioseparation and determination of selenomethionine enantiomers in selenized yeast was investigated using chiral separation techniques based on different principles, coupled on-line to inductively coupled plasma mass spectrometry (ICP-MS) for selenium-specific detection. High performance liquid chromatography (HPLC) on a beta-cyclodestrin (beta-CD) column, cyclodextrin-modified micellar electrokinetic chromatography (CD-MEKC), gas chromatography (GC) on a Chirasil-L-Val column, and HPLC on a Chirobiotic T column have been investigated as the chiral separation techniques. For HPLC separation on the beta-CD column, and also for CD-MEKC, selenomethionine enantiomers were derivatized with NDA/CN(-). For chiral separation by GC, selenomethionine enantiomers were converted into their N-trifluoroacetyl (TFA)-O-alkyl esters. The developed hybridation methodologies are compared with respect to enantioselectivity, sensitivity and analysis time. The usefulness of the best-suited method [HPLC (Chirobiotic T)-ICP-MS] was demonstrated by its application to the successful chiral speciation of selenium and D-and L-selenomethionine content determination in selenized yeast.     

Development and evaluation of a high‐performance liquid chromatography/isotope ratio mass spectrometry methodology for δ13C analyses of amino sugars in soil

Amino sugars have been used as biomarkers to assess the relative contribution of dead microbial biomass of different functional groups of microorganisms to soil carbon pools. However, little is known about the dynamics of these compounds in soil. The isotopic composition of individual amino sugars can be used as a tool to determine the turnover of these compounds. Methods to determine the δ¹³C of amino sugars using gas chromatography/combustion/isotope ratio mass spectrometry (GC/C/IRMS) have been proposed in literature. However, due to derivatization, the uncertainty on the obtained δ¹³C is too high to be used for natural abundance studies. Therefore, a new high‐performance liquid chromatography/isotope ratio mass spectrometry (HPLC/IRMS) methodology, with increased accuracy and precision, has been developed. The repeatability on the obtained δ¹³C values when pure amino sugars were analyzed were not significantly concentration‐dependent as long as the injected amount was higher than 1.5 nmol. The δ¹³C value of the same amino sugar spiked to a soil deviated by only 0.3‰ from the theoretical value. Copyright © 2009 John Wiley & Sons, Ltd.     

Effects of operating parameters on countercurrent extraction of hemicellulosic sugars from pretreated softwood

In a previous study using a continuous countercurrent screw extractor for two-stage dilute-acid hydrolysis, which was focused on the effects of liquid-to-insoluble solids (L/IS) ratio, we demonstrated that by using low volumes of wash water soluble sugars can be recovered from first-stage pretreated softwood at high yields and also at high sugar concentrations. In this study, we investigated the effects of important operating parameters other than the L/IS ratio, such as the feed rates of water and pretreated biomass and the extractor inclined angle, on the performance of the extractor using first-stage pretreated softwood. As biomass and water feed rates increased at the same L/IS ratio, the recovery yield of soluble sugars decreased, probably owing to a reduced solids residence time in the extractor, which is related to the solid/liquid contact time. The sugar recovery yield was higher at a higher extractor inclined angle. This may be attributed to the effects of increased back mixing and a longer residence time for solids at a higher extractor angle. Countercurrent extraction was also carried out with other pretreated biomass having smaller particle sizes and poor drainage rates. The countercurrent screw extractor was found to be unsuitable for these fine materials due to the slow liquid drainage rate and filter-clogging problems. In a test for stability of soluble sugars in first-stage softwood hydrolysate, irrespective of the storage temperature and storage form, the sugar concentration slowly decreased with storage time. However, storage in slurry form showed higher sugar stability compared with that in liquor form at the same conditions.

     

Interference of Transformer oil Matrices to the Internal Standards on PCB Quantification

Abstract

Polychlorinated biphenyls (PCBs) are toxic, perssstent, global environmental contaminants which were formulated as complex mixtures of congeners. Many methods have been developed in the past to analyze PCB in transformer oil samples for regulatory purposes. The most important consideration in the cleanup procedure is the ability to remove the oil from the sample matrix, since trace amount of oil will interfere with the subsequent GC-MS analysis. Electron capture detection (ECD) has been the most common method for gas chromatographic analysis of PCBs because of its high sensitivity toward halogenated compounds. ECD can also respond to some non-PCB compound resulting in biased concentrations of PCB. In this work, a two-stage cleanup method, using DMSO liquid/liquid extraction and HPLC column chromatography. has been applied to two types of transformer oil. Five internal standards have been selected to show their performance in the presence of different oil matrices. The comparison of the PCB quantification at different conditions for GC-MS and GC-ECD will be demonstrated.     

Feasibility of enhancing high-performance liquid chromatography using microwave radiation

High-performance liquid chromatography (HPLC) is the most versatile of the chromatographic techniques because it is applicable to a wide variety of analytes. Unfortunately, liquid mobile phases have relatively low diffusivities. A novel approach is presented for increasing the diffusivity of a liquid mobile phase. The method advocated in this study is the first process that has been described by which it is possible to increase the diffusivity of a liquid while having essentially no effect on other physical properties of the liquid, such as the temperature or solvating power. It is demonstrated that it is possible to sharpen peaks, in an HPLC separation, by the application of microwave radiation.