Glycoconjugated polymer: Synthesis and characterization of poly(vinyl saccharide)‐block‐polystyrene‐block‐poly(vinyl saccharide) as an amphiphilic ABA triblock copolymer

Styrene (St) was polymerized with α,α′‐bis(2′,2′,6′,6′‐tetramethyl‐1′‐piperidinyloxy)‐1,4‐diethylbenzene ( 1 ) as an initiator (bulk, [St]/] 1 ] = 570) at 120 °C for 5.0 h to obtain polystyrene having 2,2,6,6‐tetramethylpiperidiloxy moieties on both sides of the chain ends ( 2 ) with a number‐average molecular weight (M_n) of 14,300 and a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.14. 4‐Vinylbenzyl glucoside peracetate ( 3a ) was polymerized with 2 as a macromolecular initiator and dicumyl peroxide (DCP) as an accelerator in chlorobenzene at 120 °C. The polymerization with the [ 3a ]/[ 2 ]/[DCP] ratio of 30/1/1.2 for 5 h afforded a product in a yield of 73%; it was followed by purification with preparative size exclusion chromatography to provide the ABA triblock copolymer containing the pendant acetyl glucose on both sides of the chain ends ( 4a ; M_n = 21,000, M_w/M_n = 1.16). Similarly, the polymerization of 4‐vinylbenzyl maltohexaoside peracetate produced the ABA triblock copolymer containing the pendant acetyl maltohexaose on both side of the chain end ( 4b ; M_n = 31,800, M_w/M_n = 1.11). Polymers 4a and 4b were modified by deacetylation into amphiphilic ABA triblock copolymers containing the pendant glucose and maltohexaose as hydrophilic segment, 5a and 5b , respectively. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 3978–3985, 2006     

Crystallisation behaviour of high density polyethylene blends with bimodal molar mass distribution 1. Basic characteristics and isothermal crystallisation

Isothermal crystallisation of high density polyethylene (HDPE) blends and their parent polymers was investigated. The blends having broad bimodal molar mass distributions and various compositions were prepared by blending a high molar mass (M_w=330 kg/mol, M_w/M_n=4.8) and a low molar mass HDPE (M_w=34 kg/mol, M_w/M_n=10) in different ratios in xylene solution. The blends and their parent components were characterised by size-exclusion chromatography, dynamic rheological and density measurements. Crystallisation kinetics were studied using a polarised light microscope equipped with an in-house built hot stage and by differential scanning calorimetry. The Avrami theory was applied for crystallisation kinetics analysis. Such crystallisation kinetics parameters as nucleation rate, nucleation density, the Avrami index and cystallisation rate contant were determined for the blends and their parent polymers.According to the results obtained an increasing polydispersity of the sample had a slight increasing effect on the Avrami index, indicating gain in prevalence of the thermal nucleation over the athermal one. In all samples nucleation density increased continuously during crystallisation verifying that the presence of a certain thermal nucleation was typical for all the materials studied. Both the crystallisation rate constant and the nucleation rate decreased with increasing molar mass of the sample. The nucleation density increased proportionally to the increase in average molar mass and the values were larger at lower crystallisation temperatures.The formed supermolecular structure was found to be sensitive to the blend composition and crystallisation temperature. Irregular banded or non-banded spherulites were observed in the materials. Banding of spherulites was typical for the samples having higher average molar mass. The superstructures observed in this work were smaller and vaguer than the superstructures reported in the earlier studies of polyethylene materials having similar average molar mass but narrow molar mass distribution.     

Development of a new series of polyamine-type polymeric surfactants used for emulsion liquid membranes

By summarizing studies of surfactants used for emulsion liquid membrane, a new polyamine-type surfactant called LMA has been developed. This type of surfactant is composed of copolymer of isobutene and isoprene in hydrophobic site and polyethylene polyamine [NH₂(CH₂CH₂NH)_nCH₂CH₂NH₂, n≥1] in hydrophilic site. Experimental results show that the characteristics of this surfactant mainly depends on its mean molecular weight and its distribution of molecular weight, and the suitable surfactants are those with number-average molecular weight (M_n) of 5000–9000 and proper molecular weight distribution (usually M_w/M_n=3.0–6.0).     

Measurements and modeling of cloud point behavior for polypropylene/n-pentane and polypropylene/n-pentane/carbon dioxide mixtures at high pressure

The phase behavior of polypropylene (PP) in n-pentane and n-pentane/carbon dioxide solvent mixtures has been studied using a high-pressure variable volume view cell. Cloud point pressures for polypropylene (M_w=50,400) in near-critical n-pentane were studied at temperatures ranging from 432 to 470 K for polymer concentrations of 1 to 15 mass%. Furthermore, cloud point pressures for polypropylene (M_w=95,400) in near-critical n-pentane were studied at temperatures ranging from 450 to 465 K for polymer concentrations of 1 to 8 mass%. Cloud point pressures were also measured for PP (M_w=200,000, 3 mass%) in n-pentane at temperatures ranging from 450 K to 465 K. The cloud point pressures for PP (M_w=50,400) in n-pentane/CO₂ mixtures were determined for PP concentrations of 3.0 mass% and 9.7 mass% with CO₂ solvent concentrations ranging from 12.6 mass% to 42.0 mass% at temperatures ranging from 405 K to 450 K. All of the experimental cloud point isopleths were relatively linear with approximately the same positive slope indicating LCST behavior. The experimental cloud point pressures were relatively insensitive to the concentration and molecular weight of polypropylene. At a given temperature, the cloud point pressure of the PP/n-pentane/carbon dioxide system increased almost linearly with increasing carbon dioxide solvent concentration (for carbon dioxide concentrations less than 30 mass%). The Sanchez–Lacombe (SL) equation of state was used to model the experimental data.     

Living ring‐opening polymerization based on neighboring group participation

Cationic ring‐opening polymerization of a five‐membered cyclic dithiocarbonate having benzoxymethyl group; 5‐benzoxymethyl‐1,3‐oxathiolane‐2‐thione, was carried out with TfOH or TfOMe as an initiator in PhCl at rt – 60 °C. The molecular weight distribution (M_w/M_n) of the polymer obtained with TfOMe was very narrow even at 60 °C (M_w/M_n 1.14), and the Mn value of the polymers estimated by GPC was in good agreement with the molecular weight determined from ¹H‐NMR. The living nature of the polymerization was confirmed by the conversion dependence of the Mn (M_w/M_n) and the correlation of the experimental and theoretical M_n (M_w/M_n) values.     

Manipulation of chain transfer agent and cross-linker concentration to modify latex micro-structure for pressure-sensitive adhesives

N-Dodecyl mercaptan (NDM) chain transfer agent and allyl methacrylate (AMA) cross-linker were used to manipulate latex properties in a starved seeded semi-batch emulsion polymerization of butyl acrylate (BA) and methyl methacrylate (MMA) or with a third monomer, acrylic acid (AA). Latexes with higher gel content and lower sol polymer molecular weight (M_w) were produced by adding only AMA. On the other hand, latexes with lower gel content and M_w were produced by adding only NDM. In addition, at a constant AMA concentration (0.2 phm), the addition of NDM (0.2 phm) decreased gel content, increased molecular weight between cross-linking points (M_c), and decreased M_w. Adding more NDM (to a total of 0.4 phm) further decreased the gel content, while decreasing the tested M_c and increasing M_w. It was also found that using higher concentrations of both AMA and NDM could produce latex with similar gel content, but smaller M_c and M_w, compared to the latex produced at lower concentrations of both NDM and AMA. Regarding the influence of AA, gel content was increased and M_w was significantly decreased with an increase in AA concentration and a decrease in MMA concentration. The performance of the latexes was evaluated for application as a pressure-sensitive adhesive (PSA).     

Reaction parameters in the RAFT mediated dispersion polymerization of styrene

Monodisperse polystyrene (PS) particles were prepared by a living radical dispersion polymerization with a reversible addition‐fragmentation chain transfer (RAFT) agent in an ethanol medium. In the presence of RAFT agent, the effects of various reaction parameters on the characteristics of PS particles were systematically investigated. When no RAFT agent was involved, the number‐average molecular weight (M_n) of the PS particles increased from 17,800 to 30,000 g/mol, but the weight‐average diameter (D_w) decreased from 2.54 to 2.06 μm with the increase of poly(N‐vinylpyrrolidone) content from 4.0 to 16.0 wt %. No correlation between the M_n and the coefficient of variation (CV) was observed. However, when the RAFT concentration varied from 0 to 2.0 wt %, all of the conversion, M_n, D_w, CV, and polydispersity index (M_w/M_n) decreased. This indicates that the RAFT agent alters the inverse behavior between the molecular weight (MW) and particle size shown in the conventional dispersion polymerization. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 872–885, 2008     

Essential work of fracture: An approach to study the fracture behavior of acrylic bone cements modified with comonomers containing amine groups

The fracture behavior of acrylic bone cements modified with comonomers containing amine groups was studied using the essential work of fracture approach. The cements were prepared with either 2-(diethylamino)ethyl-acrylate (DEAEA), 2-(dimethylamino)ethyl-methacrylate (DMAEM) or 2-(diethylamino)ethyl-methacrylate (DEAEM) as comonomer in the liquid phase. Double-Edge-Notched Tensión (DENT) specimens were tested in a universal testing machine at 5 mm/min. The results showed that the essential work (w_e) and nonspecific value of fracture (βw_p) of bone cements modified with all percentages of comonomer were notably increased compared with unmodified bone cement. From Scanning Electron Microscopy (SEM) micrographs, ductile behavior was observed for modified bone cements, i.e. the crack propagation is stable, whereas the unmodified cement exhibited brittle behavior indicating unstable crack propagation. The use of the essential work of fracture approach is suggested to determine the fracture behavior of cements that do not exhibit a linear stress-strain relationship.     

Effect of polycondensation methods on molecular weight distribution of nylon 610

Polycondensation methods greatly influence the molecular weight distribution of poly(hexamethylene sebacamide) (nylon 610) as determined by gel permeation chromatography (GPC). The ratio of weight average molecular weight to number average molecular weight (M_w/M_n) was used as a measure for estimating the molecular weight distribution. The M_w/M_n ratios of nylon 610 obtained from melt, solid phase, and high temperature polycondensation methods were 2 to 3.5, which were expected values for the most probable distribution. However, those for polymers obtained from the direct polycondensation in the presence of triphenylphosphine, interfacial polycondensation and low temperature polycondensation using an acid chloride varied over a wide range from 3.5 to 8.5. The effect of the kind of organic solvents in the interfacial method on the M_w/M_n ratios was especially large, and the molecular weight distribution could be controlled to some extent by selecting an appropriate solvent.     

Effects of radiation and chain ends on fatigue behaviour of polystyrene

Fatigue lifetimes, under a given alternating stress amplitude, have been determined for a series of linear and branched polystyrenes. The branched polymers were obtained by a crosslinking reaction using γ-irradiation from a Co⁶⁰ source. By control of irradiation time, a series of branched samples of progressively increasing weight average molecular weight ($\text{M}$_w), with little change in number average molecular weight ($\text{M}$_n, were obtained. From comparison of fatigue data for these irradiated and branched samples with fatigue data obtained on a series of linear polystyrenes of increasing molecular weight, it may by concluded that appreciable increases in fatigue endurance can be achieved by increase in $\text{M}$_n and reduction in chain end density. For the irradiated samples, whether irradiated in air or in vacuum, fatigue lifetimes were comparable to or less than lifetimes to fracture for the unirradiated polymer, even though significant increases in $\text{M}$_w had occurred. It is suggested that the improved fatigue performance with increase of $\text{M}$_n is a consequence of increased craze stability resulting from the greater degree of chain entanglement and the smaller proportion of chain end defects.     

Polymer degradation during radiation-induced emulsion polymerization of styrene

Styrene was polymerized in emulsion with initiation by γ-rays at a dose rate of 0.6 Mrad/hr. Polymerization rates were as expected from previous reports by others. No branching or crosslinking was detectable, and the M _w/M _n ratio of the polystyrene did not change significantly during the course of the polymerization reaction. The molecular weight of the product polymer decreased with increasing conversion, in contrast to the behavior of chemically initiated emulsion polymerizations. Monomer-free polystyrene does not degrade under the same radiation conditions, and the progressive decrease of polymer molecular weight with conversion is shown to result from the presence of monomer.     

Synthesis of well-defined, polymer-grafted silica nanoparticles via reverse ATRP

The surface grafting onto ultrafine silica via reverse ATRP of methyl methacrylate initiated by peroxide groups introduced onto the surface and conventional ATRP of Styrene initiated by the hybrid nanoparticles were investigated. The introduction of peroxide groups onto the silica surface was achieved by the reaction of hydrogen peroxide with chlorosilyl groups, which were introduced by the treatment of silica with thionyl chloride. Well-defined polymer chains were grown from the nanoparticle surfaces to yield individual particles composed of a silica core and a well-defined, densely grafted outer polymer layer. The polymerization was closely controlled in solution at quite low temperature such as 70 °C. In both cases, linear kinetic plots, linear plots of molecular weight (M_n) versus conversion, in hydrodynamic diameter with increasing conversion, and narrow molecular weight distributions (M_w/M_n) for the grafted polymer samples were observed. Hydrolysis of silica cores by hydrofluoric acid treatment enabled characterization of cleaved polymer using GPC. Ultrathin films of hybrid nanoparticles were examined using TEM and AFM.     

Enhanced mechanics in injection molded isotactic polypropylene/polypropylene random copolymer blends via introducing network-like crystal structure

The crystallization behavior, rheological behavior, mechanical properties and microstructures of injection molded isotactic polypropylene(i PP), polypropylene random copolymer(co-PP) and i PP/co-PP blends were investigated. Differential scanning calorimetry(DSC) and dynamic rheological analysis illustrated that i PP and co-PP were compatible in the blends and co-PP uniformly dispersed in the i PP phase. Polarizing optical microscope(POM) was adopted to observe the crystal size and morphology evolution. The results of mechanical properties and scanning electron microscopy(SEM) indicated that the crystal size of i PP in i PP/co-PP blends(10 wt% co-PP + 90 wt% i PP and 30 wt% co-PP + 70 wt% i PP) radically decreased after the incorporation of co-PP. During crystallization, the molecular chain segments of co-PP could penetrate i PP spherulites and form a network-like crystalline structure. The network-like crystal structure could effectively transmit stress and consume more energy to overcome intermolecular forces to resist stretching. In this way, the strength would improve to a certain degree. The impact fracture mechanism of i PP/co-PP blends is quasi ductile fracture by multiple crazes. Our work discovered that the blends containing 10 wt% and 30 wt% of co-PP exhibited prominent toughness and reinforcement.     

Synthesis of poly(p‐phenylene) macromonomers and multiblock copolymers

Rigid‐rod poly(4′‐methyl‐2,5‐benzophenone) macromonomers were synthesized by Ni(0) catalytic coupling of 2,5‐dichloro‐4′‐methylbenzophenone and end‐capping agent 4‐chloro‐4′‐fluorobenzophenone. The macromonomers produced were labile to nucleophilic aromatic substitution. The molecular weight of poly(4′‐methyl‐2,5‐benzophenone) was controlled by varying the amount of the end‐capping agent in the reaction mixture. Glass‐transition temperatures of the macromonomers increased with increasing molecular weight and ranged from 117 to 213 °C. Substitution of the macromonomer end groups was determined to be nearly quantitative by ¹H NMR and gel permeation chromatography. The polymerization of a poly(4′‐methyl‐2,5‐benzophenone) macromonomer [number‐average molecular weight (M_n) = 1.90 × 10³ g/mol; polydispersity (M_w)/M_n = 2.04] with hydroxy end‐capped bisphenol A polyaryletherketone (M_n = 4.50 × 10³ g/mol; M_w/M_n = 1.92) afforded an alternating multiblock copolymer (M_n = 1.95 × 10⁴ g/mol; M_w/M_n = 6.02) that formed flexible, transparent films that could be creased without cracking. © 2001 John Wiley & Sons, Inc. J Polym Sci Part A: Polym Chem 39: 3505–3512, 2001     

Cationic polymerization of isobutylene with H2O/TiCl4 initiating system in the presence of electron pair donors

Cationic polymerization of isobutylene (IB) in a mixture of methylene dichloride (CH₂Cl₂) and n-hexane (n-Hex) was conducted by using H₂O as initiator, TiCl₄ as co-initiator in the presence of strong external electron pair donor (ED), such as pyridine (Py), dimethylacetamide (DMA) or triethylamine (TEA). The effects of ED concentration, TiCl₄ concentration, solvent polarity, polymerization temperature (T) and time on IB polymerization, molecular weight (MW) and molecular weight distribution (MWD, M_w/M_n) of polyisobutylene (PIB) products were investigated. The relative amount of polymer formed via uncontrolled initiation by conventional active species (I) decreased with increasing the solvent polarity, TiCl₄ concentration and ED concentration in the polymerization. The desirable polymerization of IB with apparent absence of chain transfer reactions could be obtained by H₂O/TiCl₄ initiating system in the presence of ED under the appropriate reaction conditions. The external electron pair donors and TiCl₄ did specially play important and effective roles on polymerization.     

Aqueous RAFT polymerization of acrylamide: A convenient method for polyacrylamide with narrow molecular weight distribution

Controlled and homogeneous free-radical polymerization of acrylamide(AM) in aqueous phase was realized by using S,S'-bis(α,α'-dimethyl-α'-acetic acid)-trithiocarbonate as a reversible addition-fragmentation transfer(RAFT) agent. Linear increases in molecular weight with conversion and narrow molecular weight distribution were observed for polyacrylamide(PAM) throughout the polymerization. By this method, PAMs with controlled molecular weight(up to 1.0 × 10~6) and narrow molecular weight distribution(M_w/M_n 1.2) were prepared. This study provides an effective method for synthesis of PAMs with narrow molecular weight distribution under environmentally friendly conditions.     

Atom transfer radical polymerization of n-octyl acrylate under microwave irradiation

The atom transfer radical polymerization (ATRP) of n-octyl acrylate (OA) was successfully carried out using ethyl-2-bromobutyrate as an initiator, and CuBr/2,2^′-bipyridine (bpy) as a catalyst under microwave irradiation (MI) at 76.8 °C. The polymerization of n-octyl acrylate under MI showed linear first-order rate plots, a linear increase of the number-average molecular weight M_n with conversion, and low polydispersities, 1.1<M_w/M_n<1.4, where M_w is weight-average molecular weight. The ATRP of n-octyl acrylate is well controlled. Under the same experimental conditions, the apparent rate constant, k_p^app, under MI is larger apparently than that under conventional heating. In addition, the effects of concentration of catalyst and other factors on polymerization are reported.     

Control of molecular weight distribution in polycondensation polymers 2. Poly(ether ketone) synthesis

Synthesis of aromatic poly(ether ketone) (3) with a narrow molecular weight distribution (M_w/M_n) was investigated via polycondensation. M_ns of 3 could be controlled varying the feed ratio of monomer (1) and initiator (2) maintaining relatively narrow M_w/M_ns (<1.3). The kinetics of polycondensation obeyed a first-order relationship between polycondensation time and -(1/[2]₀) ln([1]/[1]₀), and the rate of polycondensation was estimated as 2.57 mol⁻¹ L h⁻¹. MALDI-TOF mass analysis of 3 indicated that polycondensation should proceed via chain growth manner to give 3 having an initiator unit in each chain end.     

Microwave‐improved polymerization of ϵ‐caprolactone initiated by carboxylic acids

The ring‐opening polymerization of ε‐caprolactone (ε‐CL), initiated by carboxylic acids such as benzoic acid and chlorinated acetic acids under microwave irradiation, was investigated; with this method, no metal catalyst was necessary. The product was characterized as poly(ε‐caprolactone) (PCL) by ¹H NMR spectroscopy, Fourier transform infrared spectroscopy, ultraviolet spectroscopy, and gel permeation chromatography. The polymerization was significantly improved under microwave irradiation. The weight‐average molecular weight (M_w) of PCL reached 44,800 g/mol, with a polydispersity index [weight‐average molecular weight/number‐average molecular weight (M_w/M_n)] of 1.6, when a mixture of ε‐CL and benzoic acid (25/1 molar ratio) was irradiated at 680 W for 240 min, whereas PCL with M_w = 12,100 and M_w/M_n = 4.2 was obtained from the same mixture by a conventional heating method at 210 °C for 240 min. A degradation of the resultant PCL was observed during microwave polymerization with chlorinated acetic acids as initiators, and this induced a decrease in M_w of PCL. However, the degradation was hindered by benzoic acid at low concentrations. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 13–21, 2003     

Photodegradation of biodegradable polyesters: A comprehensive study on poly(l-lactide) and poly(?-caprolactone)

The photodegradation of melt-crystallized and amorphous-made poly(l-lactide) (PLLA-C and PLLA-A, respectively) and cast-crystallized poly(?-caprolactone) (PCL) was investigated comprehensively for the periods up to 200 h using gel permeation chromatography, differential scanning calorimetry, tensile testing, and polarization optical microscopy. The photodegradation of PLLA and PCL films proceeds via a bulk erosion mechanism, indicating that UV penetrates the specimens with no significant reduction in its intensity, irrespective of the chemical structure and the crystallinity of biodegradable polyesters. The photodegradability of PCL chains was higher than that of PLLA chains. This strongly suggests that the chemical structure of the two sequential groups adjacent to the ester oxygen rather than the density of ester group is crucial to determine the photodegradability of biodegradable polyesters. Although PLLA chains are photodegradable even in the crystalline regions, their photodegradability is lower than that in the amorphous regions. The significant increase in weight-average molecular weight (M_w)/number-average molecular weight (M_n) was observed for PLLA-A and PCL films, even when the decrease in M_n by UV irradiation was small. Most of the tensile properties of PLLA and PCL films remained unchanged during UV irradiation, while solely the elongation at break of PCL film significantly decreased. This result reflects that among the tensile properties the elongation at break was most sensitive to the change in molecular characteristics of biodegradable polyesters by UV irradiation. The contrast between bright and dark parts of Maltese crosses remained unchanged for the spherulites in PLLA-C and PCL films even after UV irradiation for 200 h. This result exhibits that the cleaved fraction of the tie chains was too low to cause the traceable disorientation of lamellae.