Ag/TiO2的制备及光催化性能研究

以钛酸丁酯为钛源,采用溶胶-凝胶法制备了Ag掺杂纳米TiO2,结合XRD、TEM、Uv-vis等测试手段,对样品的结构和性能进行了表征.以甲基橙溶液为目标降解物,探讨了Ag掺杂纳米TiO2的光催化活性,分析了Ag掺杂纳米TiO2提高光催化性能的机理.结果表明,Ag掺杂使TiO2晶粒减小,拓展了TiO2的光谱响应范围,降低了光生电子和空穴的复合几率;Ag掺杂后,TiO2光催化剂的吸收光谱向可见光区发生红移.Ag掺杂量为n(Ag)∶n(TiO2)=0.08;,紫外光下240 min,Ag掺杂纳米TiO2前后材料对甲基橙溶液去除率由60.3;提高到83.1;.     

爆轰法合成超小TiO2的光催化性能分析

颗粒尺寸是影响TiO2光催化活性的重要因素,颗粒越小其光催化效率越高.在密闭的反应釜内引爆用含钛前驱体、硝酸铵、黑索金与一定量的聚苯乙烯小球制备的浆状混合炸药制备了超小的TiO2纳米颗粒.研究了炸药配比对TiO2的形貌、分散性、颗粒尺寸的影响,并通过降解甲基橙溶液表征超小TiO2的光催化性能.结果发现:制备的TiO2由金红石相与锐钛矿相组成,大部分颗粒呈球形或不规则四边形,尺寸在10nm左右,少量颗粒尺寸大于20nm,结晶度较好.炸药配比对TiO2的结晶度、颗粒大小、分散性等有较大影响.TiO2的禁带宽度在2.8eV左右,低于锐钛矿相与金红石相的禁带宽度,能够提高太阳光的利用率.爆轰制备的超小TiO2催化降解甲基橙溶液50min时,甲基橙的降解率为30;,明显高于爆轰法制备的颗粒较大的TiO2与铜粒子掺杂的纳米TiO2的光催化速率,光催化性能得到明显提高.     

炭黑吸附水热法制备纳米TiO2粉体及其光催化降解甲基橙

利用炭黑吸附钛酸异丙酯水热法制得锐钛矿型TiO2纳米粉体.采用热重/差热分析(TG-DTA)、X-射线衍射(XRD)、扫描电镜(SEM)、比表面积吸附(BET)和紫外-可见光谱(Uv-vIS)等分析方法对不同煅烧机制下所得粉体的物相、颗粒度、分散性和光吸收性能进行表征.同时利用纳米TiO2粉体对甲基橙进行了光催化降解,研究了其光催化性能.结果表明,炭黑的吸附阻止了纳米TiO2超细颗粒的团聚和烧结,制得的颗粒分散均匀、具有单一锐钛矿晶型结构的TiO2纳米粉体.经500℃煅烧获得的TiO2粉体粒径约为15 nm,比表面积为76.31 g/m2.在紫外灯照射下,由于炭黑的吸附和纳米TiO2的光催化形成协同效应,甲基橙的光催化降解率在6min达到99;.     

可见光响应氮掺杂TiO2制备与性能表征

采用水热法制备了可见光响应的氮掺杂TiO2光催化剂,利用XRD、SEM、XPS、UV-vis对样品结构、形貌和光谱等性质进行表征.研究结果表明:氮掺杂抑制晶粒长大,促进晶格畸变;氮进入TiO2晶格中,引起TiO2光催化剂的激发,吸收光谱向低能方向移动.以降解甲基橙为模型反应,研究样品的光催化性能;以对苯二甲酸作为·OH自由基捕获剂,利用化学荧光技术研究光催化反应体系中·OH自由基生成量.结果表明:与纯TiO2相比,氮掺杂样品具有较高的光催化活性.这与下列因素有关:氮掺杂样品具有较小的晶粒尺寸,有利于促进光生电荷的分离与相界面上电荷转移效率,降低TiO2能隙并使吸收光谱红移.在实验条件下,光催化性能随n(N/Ti)比值的增大而增强;羟基自由基的生成速率与光催化活性规律一致,即·OH的生成速率越大,光催化活性越高.     

Ce掺杂TiO2纳米复合薄膜的制备及光催化活性

采用溶胶-凝胶技术,以CTAB作为模板剂,提拉法镀膜制备了Ce掺杂TiO2纳米复合薄膜,利用XRD、N2吸附-脱附、UV-Vis、SEM及XPS对样品进行了表征.结果表明,铈离子以Ce4+和Ce3+两种形式存在于体系中,而CTAB有效抑制了TiO2晶粒的长大和二氧化钛晶相的转变,加入CTAB的Ce掺杂TiO2纳米复合薄膜的吸收带边较纯的TiO2发生了红移.光催化活性表明,这种处理方式明显提高了TiO2光催化活性.在紫外光照120 min下,CRAB(1.0;)/Ce(1.0;)-TiO2纳米复合薄膜的光催化活性最佳,对甲基橙降解率达到95.3;.     

TiO2/P3HT纳米复合材料光催化降解甲基橙的动力学研究

用化学氧化聚合法制备了导电聚合物聚3-己基噻吩(P3HT).用聚3-己基噻吩改性纳米二氧化钛,合成TiO2/P3HT纳米复合微粒.对其光催化降解甲基橙的反应动力学进行了分析,测定了反应的表观活化能.结果表明,纯纳米TiO2和TiO2/P3HT纳米复合微粒光催化降解甲基橙的反应均为一级反应;纳米TiO2经聚3-己基噻吩(P3HT)修饰后在可见光下的光催化活性得到提高,且提高降解温度有利于提高甲基橙的降解率,纳米TiO2经P3HT修饰后降解甲基橙的表观活化能由23.44 KJ/mol下降到19.36 kJ/mol.     

乙酰丙酮对PMMA负载锐钛矿型TiO2薄膜及其光催化性能影响

以钛酸丁酯作为钛源,水为溶剂,乙酰丙酮(AcAcH)为表面修饰剂,采用微波水热辅助溶胶-凝胶法制备了纳米晶二氧化钛水溶液,利用提拉镀膜法在聚合物聚甲基丙烯酸甲酯(PMMA)基板上沉积得到了透明TiO2纳米晶薄膜.通过X射线衍射(XRD)、红外光谱(FTIR)、透射电子显微镜(TEM)、原子力显微镜(AFM)和紫外-可见光吸收光谱(UV-Vis)等对TiO2纳米颗粒和薄膜的晶相组成、表面形貌及光学性能进行表征.同时通过紫外光光催化降解罗丹明B研究了TiO2薄膜的光催化性能.结果表明:通过引入乙酰丙酮,可以得到高度分散、晶相为锐钛矿型的TiO2水溶胶,在PMMA基板上沉积得到的薄膜表面平整、致密,具有良好的透光率,经过180 min紫外光照射,对罗丹明B的降解率达到90;以上.     

镧掺杂混晶结构TiO2纳米粉体的制备及其光催化性能

以钛酸四丁酯为Ti源,采用溶胶-凝胶自蔓燃法制备了镧掺杂的La-TiO2(简写为LT)纳米粉体.利用X射线粉末衍射(XRD)、红外光谱(FIIR)、透射电子显微镜(TEM)等对掺杂型TiO2粉体的晶型结构与颗粒尺寸等进行表征.利用紫外-可见光吸收光谱(UV-vis)研究了H2O2改性、镧掺杂量以及混晶结构对TiO2纳米粉体降解甲基橙的影响.结果表明:镧掺杂混晶TiO2粉体的光催化活性明显优于未掺杂的锐钛矿TiO2粉体.当La3+掺杂量为0.5;,合成温度为475℃(金红石相含量为26.0;)时,得到的TiO2粉体光催化活性最好.H2O2的加入有助于TiO2光催化剂表面的电子-空穴对生成,提高光催化剂对甲基橙的降解率,当H2O2浓度为6;时,光照3h后,降解率达到了91.97;.     

静电自组装制备镧掺杂高岭石基纳米TiO2光催化材料研究

采用静电自组装方法制备了镧掺杂高岭石基纳米TiO2光催化材料.采用巯丙基三甲氧基硅烷偶联剂对高岭石进行干法改性,采用30; H2O2/HOAc将偶联剂巯基基团氧化为磺酸基基团.在静电引力的作用下,带负电荷的高岭石与带正电荷的钛聚合阳离子和La3+自发地组装在一起,经一定温度热处理得到镧掺杂高岭石基纳米TiO2光催化材料.采用XRF、XRD、FT-IR、SEM和PL等对材料进行分析,采用甲基橙染料评价材料的光催化性能.研究表明:采用静电自组装方法可有效提高高岭石与纳米TiO2的复合效率;镧掺杂导致TiO2与高岭石之间的结合力增强;适量的镧掺杂导致锐钛矿晶体发生畸变,能带结构改变,电子-空穴对复合几率降低,进而导致其光催化性能增强;镧掺量5 mol;的复合材料对甲基橙溶液表现出更高的光催化脱色效果.     

胶原纤维为模板制备Gd掺杂纤维状二氧化钛及光催化性能研究

以胶原为模板剂、硫酸钛为钛源、硝酸钆为掺杂源制备了钆掺杂纤维结构TiO2(Gd-TiO2).通过扫描电镜(SEM)、X射线衍射仪(XRD)、紫外可见漫反射光谱(UV-Vis-DRS)、X射线光电子能谱(XPS)对样品的表面形貌、晶相组成、紫外吸收带、元素组成及化合价态进行了分析.以甲基橙为目标降解物,研究了样品的光催化性能并确定钆的最佳掺杂量.结果表明:600℃煅烧温度下2;Gd-TiO2纤维结构完好、光催化效果最好,光反应30 min后其降解率达到91.89;,比起未掺杂试样大大提高.钆掺杂会改变TiO2的晶粒尺寸并能够抑制TiO2从锐钛矿相向金红石相转变,掺杂后紫外吸收带发生蓝移.     

CsI-LiCl共晶材料的坩埚下降法生长与闪烁性能研究

本文采用坩埚下降法,在真空密封的石英坩埚中成功生长出CsI-LiCl与CsI-LiCl:Na共晶闪烁体。通过扫描电子显微镜(SEM)观察晶体微结构表明该共晶中LiCl相与CsI相存在周期性的层状排列,CsI相的厚度在5 μm左右。共晶样品的X射线激发发射谱显示在CsI-LiCl和CsI-LiCl:Na共晶样品存在缺陷发光,在CsI-LiCl样品中还观察到了纯CsI的自陷激子(STE)发光。CsI-LiCl样品在α粒子激发下的多道能谱中观察到明显的全能峰,这一结果证明CsI-LiCl共晶可用于热中子探测的潜力。     

静电纺丝法制备CeO2微纳米纤维及其除氟性能

以聚丙烯腈(PAN)为载体,六水合硝酸铈[Ce(NO₃)₃·6H₂O]为原料,采用静电纺丝法制备了Ce(NO₃)₃/PAN纤维,在空气中热处理得到CeO₂微纳米纤维,通过XRD、BET和SEM对CeO₂微纳米纤维进行表征。采用静态吸附实验探讨了CeO₂微纳米纤维去除水溶液中氟离子的性能,考察了溶液pH值、初始氟离子浓度及共存阴离子等对吸附性能的影响。结果表明,pH=3时,CeO₂微纳米纤维对F^-的吸附性能最佳,CeO₂吸附量随着F^-浓度的增大呈上升趋势。CeO₂微纳米纤维对F^-的吸附等温线遵循Langmuir模型,二级动力学模型能很好地描述CeO₂微纳米纤维对F^-的吸附过程。CeO₂微纳米纤维的除氟性能优良,可为其实际应用提供理论参考。     

Triethyl ammonium salt of O,O′-bis(p-tolyl)dithiophosphate, [Et3NH]+[(4-MeC6H4O)2PS2]−

Triethyl ammonium Salt of O,O′-bis(p-tolyl)dithiophosphate and O,O′-bis(m-tolyl)dithiophosphate have been obtained by reaction of p- and m-cresol, respectively with P₂S₅ in toluene and have been characterized by elemental analysis, IR, ¹H and ³¹P NMR spectroscopy. The molecular structure of O,O′-bis(p-tolyl)dithiophosphate has been determined. Crystal data: [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻: Monoclinic, P2₁/c, a=15.2441(9) ?, b=10.415(2) ?, c=3.9726(9) ?, β=91.709(7)°, V=2217.5(1) ?⁻³, Z=4.Supplementary materials Additional material available from the Cambridge Crystallographic Data Centre (CCDC no. 600927 for [Et₃NH]⁺[(4-MeC₆H₄O)₂PS₂]⁻ comprises the final atomic coordinates for all atoms, thermal parameters, and a complete listing of bond distances and angles. Copies of this information may be obtained free of charge on application to The Director, 12 Union Road, Cambridge CB2 2EZ, UK (fax: +44-1223-336033; email: deposit@ccdc.cam.ac.uk or www:http://www.ccdc.cam.ac.uk).     

Crystal structure of Zn4Na(OH)6SO4Cl·6H2O

The structure of Zn₄Na(OH)₆SO₄Cl·6H₂O, a secondary mineral from Hettstedt, Germany, was determined by single-crystal X-ray diffraction. The crystals are hexagonal,a=8.413(8),c=13.095(24) Å, space group $P\bar 3$ , Z=2. The structure was refined to R=0.0554 and R_w=0.0903 for 970 reflections with I≥3σ(I). The structure can be described as zinc hydroxide layers perpendicular toc, from which sulfates and chlorides extend. The layers are held together by a system of hydrogen bonds involving hexaaquo Na⁺ ions which occupy the interlayer space.     

X-ray analysis of sideroxol from <Emphasis Type="Italic">Sideritis leptoclada</Emphasis>

Sideroxol (1), a kaurane diterpene which has the ent-7α,18-dihydroxy-15β,16β-epoxykaurane structure (MW = 320.47, C₂₀H₃₂O₃) was obtained from the acetone extract of Sideritis leptoclada plant as well as from some other Sideritis species. It crystallizes in the orthorhombic space group P2₁, 2₁, 2₁ with a = 10.967(3), b = 24.555(5), c = 6.372(4) Å, Dc = 1.240 g cm⁻³, Z = 4, and refines to R = 0.065 for 721 independent reflections. The skeleton consists of three fused six-membered rings and a five-membered ring with fused epoxide. The six membered rings exhibited slightly distorted chair conformation. In addition to sideroxol, two kaurane and five kaurene diterpenes were isolated from the hexane and acetone extracts of the studied plant.     

Photoluminescence characteristics of Mg- and Si-doped GaN thin films grown by MOCVD technique

We have studied the optical, structural and surface morphology of doped and undoped GaN thin films. The p- and n-type thin films have been successfully prepared by low-pressure MOCVD technique by doping with Mg and Si, respectively. The different carrier concentrations were obtained in the GaN thin films by varying dopant concentrations. Photoluminescence (PL) studies were carried to find the defect levels in the doped and undoped GaN thin films at low temperature. In the undoped GaN thin films, a low intensity and broad yellow band peak was observed. The donor–acceptor pair (DAP) emission and its phonon replicas were observed in both the Si or Mg lightly doped GaN thin films. The dominance of the blue and the yellow emissions increased in the PL spectra, as the carrier concentration was increased. The XRD and SEM analyses were employed to study the structural and surface morphology of the films, respectively. Both the doped and the undoped films exhibited hexagonal structure and polycrystalline nature. Mg-doped GaN thin films showed columnar structure whereas Si-doped films exhibited spherical shape grains.     

New zeotype borophosphates with chiral tetrahedral topology: (H)0.5M1.25(H2O)1.5[BP2O8]·H2O (M = Co(II) and Mn(II))

Two new isostructural open‐framework zeotype transition metal borophosphate compounds, (H)_0.5M_1.25(H₂O)_1.5[BP₂O₈]·H₂O (M = Co(II) and Mn(II)) were synthesized by mild hydrothermal method. The structure of compounds were characterized by single‐crystal X‐ray diffraction which have ordered, alternating, vertex‐sharing BO₄, PO₄, and (MO₄)OM(H₂O)₂ groups with hexagonal, P 6₁ 2 2 (No 178) space group and unit cell parameters for Co a = 9.4960(6) Å, c = 15.6230(13) Å, for Mn a = 9.6547(12) Å, c = 15.791(3) Å, Z = 1 for both of them. TGA/DTA analysis, IR spectroscopy were used for characterization. Magnetic susceptibility measurements for both of the compound indicate strong antiferromagnetic interaction between metal centers. (© 2005 WILEY‐VCH Verlag GmbH & Co. KGaA, Weinheim)     

Synthesis and Crystal Structure of 5-[2-(6-bromonaphthalenyloxymethyl)]-3-(4-morpholinomethyl)-1,3,4-oxadiazole-2(3<Emphasis Type="Italic">H</Emphasis>)-thione

Abstract  The title compound, C₁₈H₁₈BrN₃O₃S, a derivative of 1,3,4-oxadiazole, crystallizes in the triclinic space group P-1 with unit cell parameters a = 6.8731(3), b = 8.9994(4), c = 15.7099(6) ?, α = 92.779(3)°, β = 130.575(3)°, γ = 107.868(4)°, Z = 2. The dihedral angle between the mean planes of the planar naphthyl and morpholine (chair) rings with the planar oxadiazol ring is 50.1(8) and 76.8(6)°, respectively. The planar naphthyl ring is twisted 52.2(5)° with the mean plane of the morpholine ring. A group of four intermolecular close contacts are observed between a bromine atom and hydrogen atoms from the closely packed naphthyl, morpholine and oxy–methyl groups in the unit cell. These molecular interactions in concert with an additional series of π–π stacking interactions that occur between the center of gravity of the two 6-membered rings of the naphthalene group influence the twist angles of each of these three groups. A MOPAC AM1 calculation of the conformation energy of the crystal structure [226.0128(9) kcal] compared to that of the minimum energy structure after geometry optimization [29.9744(1) kcal] reveals a significantly reduced value. The twist angles of the three groups above also change after the AM1 calculation giving support to the influence of both intermolecular C–H···Br short-range interactions and Cg π–π stacking interactions on these angles which therefore play a role in stabilizing crystal packing. Graphical Abstract  Crystal structure of 5-{[(6-bromonaphthalen-2-yl)oxy]methyl}-3-(morpholin-4-ylmethyl)-1,3,4-oxadiazole-2(3H)-thione, C₁₈H₁₈BrN₃O₃S, is reported and its geometric and packing parameters described and compared to a MOPAC computational calculation. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Solubility of Ag2O into the Na2O–B2O3–Al2O3 system

The solubility of Ag₂O was measured for the Na₂O–B₂O₃ and Na₂O–B₂O₃–Al₂O₃ system with the rotating crucible method and static method, respectively, under air atmosphere at temperatures ranging from 1273 to 1423 K. The contamination of melts from crucibles could be avoided by the rotating crucible method, with which it became possible to measure the solubility of Ag₂O for the Na₂O–B₂O₃ system above the melting point of Ag for the first time. It was found that the addition of Na₂O decreases the solubility of Ag₂O while the addition of Al₂O₃ had little effect on the solubility. The effect of Na₂O and Al₂O₃ on the solubility of Ag₂O is expressed by interaction coefficients and is analyzed in terms of the basicity of melts. The solubility of Ag₂O in Na₂O–B₂O₃–Al₂O₃ melts increased with increased temperature. This phenomena was explained by a small enthalpy change in oxidation of silver.     

Crystal structure of irisolidone from the flowers of Pueraia lobata

Irisolidone (5,7-dihydroxy-6,4′-dimethoxyisoflavone) was isolated from the flowers of Pueraia lobata and its crystal structure was examined by X-ray single crystal diffraction. The crystal structure of irisolidone is monoclinic, space group P2₁/c with a = 15.491(9) ?, b = 7.895(4) ?, c = 13.321(7) ?, β = 110.546(9)° and Z = 4. Hydrogen bonding and aromatic π–π stacking assemble the title compound into a three-dimensional networking structure.