Growth of epitaxial TmFeCuO4 thin films by pulsed laser deposition

Epitaxial thin films of TmFeCuO₄ with a two-dimensional triangular lattice structure were successfully grown on yttria-stabilized-zirconia substrates by pulsed laser deposition and ex situ annealing in air. The films as-deposited below 500 °C showed no TmFeCuO₄ phase and the subsequent annealing resulted in the decomposition of film components. On the other hand, as-grown films deposited at 800 °C showed an amorphous nature. Thermal annealing converted the amorphous films into highly (0 0 1)-oriented epitaxial films. The results of scanning electron microscopic analysis suggest that the crystal growth process during thermal annealing is dominated by the regrowth of non-uniformly shaped islands to the distinct uniform islands of hexagonal base.     

Zr(IV) and Hf(IV) β-diketonate complexes as precursors for the photochemical deposition of ZrO2 and HfO2 thin films

In this paper amorphous ZrO₂ and HfO₂ thin films were obtained by direct UV irradiation of Zr(IV) and Hf(IV) β-diketonate precursor complexes on Si(1 0 0) and fused silica substrates. The precursors, Zr(CH₃COCHCOCH₃)₄ and Hf(C₆H₅COCHCOCH₃)₄ were deposited as amorphous thin films by spin coating. The photochemistry of these films was monitored by FT-IR spectroscopy. The photolysis with 254 nm light led to the loss of the ligands from the coordination complexes, and the production of metallic oxides. The thin films products were characterized by X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM). These analyses revealed that as-deposited films are amorphous and that the presence of carbon is thought to arise from the ligands. However, post-annealing of the photodeposited films favors the stoichiometric and optical properties of ZrO₂ and HfO₂ thin films.     

Preparation and characterization of ZnO-TiO2 films obtained by sol-gel method

The sol-gel route has been applied to obtain ZnO-TiO₂ thin films. For comparison, pure TiO₂ and ZnO films are also prepared from the corresponding solutions. The films are deposited by a spin-coated method on silicon and glass substrates. Their structural and vibrational properties have been studied as a function of the annealing temperatures (400-750 °C). Pure ZnO films crystallize in a wurtzite modification at a relatively low temperature of 400 °C, whereas the mixed oxide films show predominantly amorphous structure at this temperature. XRD analysis shows that by increasing the annealing temperatures, the sol-gel Zn/Ti oxide films reveal a certain degree of crystallization and their structures are found to be mixtures of wurtzite ZnO, Zn₂TiO₄, anatase TiO₂ and amorphous fraction. The XRD analysis presumes that Zn₂TiO₄ becomes a favored phase at the highest annealing temperature of 750 °C. The obtained thin films are uniform with no visual defects. The optical properties of ZnO-TiO₂ films have been compared with those of single component films (ZnO and TiO₂). The mixed oxide films present a high transparency with a slight decrease by increasing the annealing temperature.     

The effect of thermal annealing on the structural and mechanical properties of a-C:H thin films prepared by the CFUBM magnetron sputtering method

a-C:H films were prepared by closed-field unbalanced magnetron (CFUBM) sputtering on silicon substrates using argon (Ar) and acetylene (C₂H₂) gases, and the effects of post-annealing temperature on structural and mechanical properties were investigated. Films were annealed at temperatures ranging from 300 °C to 700 °C in increments of 200 °C using rapid thermal annealing equipment in vacuum ambient. Variations in microstructure were examined using Raman spectroscopy and X-ray photoelectron spectroscopy (XPS). Surface and mechanical properties were investigated by atomic force microscopy (AFM), nano-indentation, residual stress tester, and nano-scratch tester. We found that the mechanical properties of a-C:H films deteriorated with increased annealing temperature.     

Influence of annealing on the physical properties of filtered vacuum arc deposited tin oxide thin films

Tin oxide (SnO₂) thin films were deposited on UV fused silica (UVFS) substrates using filtered vacuum arc deposition (FVAD). During deposition, the substrates were at room temperature (RT). As-deposited films were annealed at 400 and 600 °C in Ar for 30 min. The film structure, composition, and surface morphology were determined as function of the annealing temperature using X-ray diffraction (XRD), atomic force microscopy (AFM), and X-ray photoelectron spectroscopy (XPS). The XRD patterns of the SnO₂ thin films deposited on substrates at RT indicated that the films were amorphous, however, after the annealing the film structure became polycrystalline. The grain size of the annealed films, obtained from the XRD analysis, increased with the annealing temperature, and it was in the range 8-34 nm. The AFM analysis of the surface revealed an increase in the film surface average grain size from 15 nm to 46 nm, and the surface roughness from 0.2 to 1.8 nm, as function of the annealing temperature. The average optical transmission of the films in the visible spectrum was >80%, and increased by the annealing ∼10%. The films’ optical constants in the 250-989 nm wavelength range were determined by variable angle spectroscopic ellipsometry (VASE). The refractive indexes of as-deposited and annealed films were in the range 1.83-2.23 and 1.85-2.3, respectively. The extinction coefficients, k(λ), of as-deposited and annealed films were in the range same range ∼0-0.5. The optical energy band gap (E_g), as determined by the dependence of the absorption coefficient on the photon energy at short wavelengths, increased with the annealing temperature from 3.90 to 4.35 eV. The lowest electrical resistivity of the as-deposited tin oxide films was 7.8 × 10⁻³ Ω cm, however, film annealing resulted in highly resistive films.     

Influence of hydrogen on structural and optical properties of low temperature polycrystalline Ge films deposited by RF magnetron sputtering

To improve the properties of polycrystalline Ge thin films, which are a candidate material for the bottom cells of low cost monolithic tandem solar cells, ∼300 nm in situ hydrogenated Ge (Ge:H) thin films were deposited on silicon nitride coated glass by radio-frequency magnetron sputtering. The films were sputtered in a mixture of 15 sccm argon and 10 sccm hydrogen at a variety of low substrate temperatures (T_s)≤450 °C. Structural and optical properties of the Ge:H thin films were measured and compared to those of non-hydrogenated Ge thin films deduced in our previous work. Raman and X-ray diffraction spectra revealed a structural evolution from amorphous to crystalline phase with increase in T_s. It is found that the introduction of hydrogen gas benefits the structural properties of the polycrystalline Ge film, sputtered at 450 °C, although the onset crystallization temperature is ∼90 °C higher than in those sputtered without hydrogen. Compared with non-hydrogenated Ge thin films, hydrogen incorporated in the films leads to broadened band gaps of the films sputtered at different T_s.     

Effects of post-annealing temperature on structural,optical, and electrical properties of MgxZn1−xO films by RF magnetron sputtering

Mg_xZn_1?xO thin films were deposited on quartz substrates by RF magnetron sputtering. The effect of post-annealing temperature on structural, optical, and electrical properties was investigated with the annealing temperatures increasing from 450 to 750 °C. The crystallinity of Mg_xZn_1?xO film annealed at 650 °C was significantly improved while the film annealed at 750 °C showed little improvement. The electrical properties degraded with the increase of annealing temperature. The annealing temperature seemed to impact the E_g value of Mg_xZn_1?xO thin films because of the variation of carrier concentration.     

Isothermal crystallization kinetic of ZnO thin films

Zinc oxide (ZnO) thin films deposited by DC magnetron sputtering were annealed in nitrogen atmosphere at different temperatures ranging from 100 to 500 °C with a step of 100 °C; the annealing time was 6 h. In order to study the film’s crystallization kinetic, their structures were monitored by means of X-ray diffraction (XRD) analysis each hour. Variation in grain size, calculated from the XRD patterns, with annealing time and temperature, obeys the classical parabolic law of grain growth. Exponent n was found to be dependent on the annealing temperature; it ranged from 5.13 to 3.8 with increase in annealing temperature. From the obtained exponent n values we inferred that the grain growth mechanism is mainly governed by the atom jumping across the grain boundary. We have found that the grain growth is characterized by a low activation energy ranging from 22 to 24 kJ/mol.     

Spectroscopic ellipsometry studies of reactively sputtered nitrogen-rich GaAsN films

Nitrogen-rich GaAsN thin films have been deposited at 500 °C by reactive rf sputtering of GaAs target in argon-nitrogen atmosphere. The arsenic content of the films was varied by changing the nitrogen percentage in the sputtering atmosphere and the As/Ga ratio in the films was estimated by X-ray fluorescence measurements. Spectroscopic ellipsometry measurements have been carried out on these films and the measured ellispometric spectra were fitted with theoretical spectra generated by using suitable model sample structures. From the best fit parameters of the dispersion model, band-gap values and variation of refractive index and extinction coefficient as a function of wavelength have been obtained for films deposited with different percentages of nitrogen in the sputtering atmosphere. The films deposited with 12% to 100% nitrogen in the sputtering atmosphere, which are of hexagonal GaN, exhibit GaN-like optical properties, though effects due to excess arsenic in amorphous phase are seen in the films deposited with less than 40% nitrogen. The films deposited with 5% to 12% nitrogen in sputtering atmosphere are dominantly polycrystalline GaAs_xN_1−x (x ≈ 0.01 to 0.08) and exhibit variations in optical parameters, which are consistent with their structure and composition. The films deposited with less than 5% nitrogen in sputtering atmosphere are arsenic-rich and amorphous.     

Dependence of chemical composition and bonding of amorphous SiC on deposition temperature and the choice of substrate

Amorphous SiC has superior mechanical, chemical, electrical, and optical properties which are process dependent. In this study, the impact of deposition temperature and substrate choice on the chemical composition and bonding of deposited amorphous SiC is investigated, both 6 in. single-crystalline Si and oxide covered Si wafers were used as substrates. The deposition was performed in a standard low-pressure chemical vapour deposition reactor, methylsilane was used as the single precursor, and deposition temperature was set at 600 and 650 °C. XPS analyses were employed to investigate the chemical composition, Si/C ratio, and chemical bonding of deposited amorphous SiC. The results demonstrate that these properties varied with deposition temperature, and the impact of substrate on them became minor when deposition temperature was raised up from 600 °C to 650 °C. Nearly stoichiometric amorphous SiC with higher impurity concentration was deposited on crystalline Si substrate at 600 °C. Slightly carbon rich amorphous SiC films with much lower impurity concentration were prepared at 650 °C on both kinds of substrates. Tetrahedral Si-C bonds were found to be the dominant bonds in all deposited amorphous SiC. No contribution from Si-H/Si-Si but from sp² and sp³ C-C/C-H bonds was identified.     

Investigation of optical parameters of Ag-In-Se thin films deposited by e-beam technique

The optical properties of the Ag-In-Se (AIS) thin films deposited by e-beam technique were investigated by means of the optical transmittance measurements. The optical absorption coefficients of the films were found to vary from 10³ to 10⁵ cm⁻¹ over the wavelength range of 300-1100 nm. The real and imaginary parts of the refractive index and dielectric constant for the as-grown and annealed films in between 100 and 400 °C were evaluated by means of both envelope method (EM) and continuous wavelet transform (CWT) method and the results were in quite good agreement with each other. The refractive index, n, dispersion over the measured wavelength range was explained by applying single-oscillator model (SOM) and the related parameters were calculated. The optical absorption process for the AIS thin films was characterized by three direct transitions from three closely spaced valence bands to a single conduction band due to the splitting of the valence band under the influence of the tetragonal crystalline field and spin-orbit interaction. The direct optical band gap energy decreases as the annealing temperature increases because of the increase in the width of band tail states near valence-band edge caused by the Se segregation. The two distinct parameters of the quasicubic model; crystal-field splitting, Δ_CF, and spin-orbit splitting, Δ_SO, were calculated for as-grown and annealed AIS thin films.     

Structural and optical properties of 6CaO·6SrO·7Al2O3 thin films derived by sol-gel dip coating process

The nanostructured 6CaO·6SrO·7Al₂O₃ (C6S6A7) thin films with cubic structure using calcium, strontium metals, aluminium isopropoxide and ethylene glycol monomethyl ether as stating materials has been fabricated via sol-gel route. Based on hydrolysis of Ca²⁺, Sr²⁺ and Al³⁺ in the sol-gel processing using ethylene glycol monomethyl ether as solvent have been employed as the precursor material. The films were coated on soda lime float glass by the dip coating technique and annealed at 450 °C in air atmosphere. The structure, morphology and composition of the films were investigated by Fourier transformed infrared spectroscopy, X-ray powder diffraction, scanning electron microscopy, atomic force microscopy and X-ray photoelectron spectroscopy indicating that the films were composed of C6S6A7 nanoparticles with cubic structure. The spectral transmittance of the films was measured in the wavelength range of 200-1100 nm using an UV-visible spectrometer. It has been found that the optical properties of the films significantly affected by precursor chemistry and annealing temperature due to the improvement of the crystallinity of the films with increasing annealing temperature and became stable when the annealing temperature is higher than 450 °C. The C6S6A7 films annealed at 450 °C had high transparency about 80% in wide visible range.     

Fluorinated nanoporous SiO2 films with ultra-low dielectric constant

Fluorinated nanoporous silica (denoted as SiO₂:F) thin films with low dielectric constant were prepared by a sol-gel method and spin coating technique. The leakage current densities of the SiO₂:F thin films were 10⁻⁸ and 3 × 10⁻⁶ A/cm² respectively for the as-deposited films and for those subjected to annealing at a temperature of 450 °C. These currents are more than one order of magnitude lower than those of the common SiO₂ films. Photoluminescent results showed strong blue-light emission and a small blue shift in the SiO₂:F films that were related to the increment of the porosity. The dielectric properties were also characterized and the k value of the annealed SiO₂:F film was found to be about 1.67. The hole size in the films is small and the size distribution is uniform for the annealed SiO₂:F samples due to the effects of fluorination. The underlying mechanism for fluorination is discussed in this paper.     

Morphology and crystal phase evolution of doctor-blade coated CuInSe2 thin films

CuInSe₂ (CIS) chalcopyrite thin films were prepared using a low-cost, non-vacuum doctor-blade coating and the thermal annealing method. An acetone-based precursor solution containing copper chloride, indium chloride, selenium chloride, and an organic binder was deposited onto a Mo-sputtered soda lime glass substrate using a doctor-blade coating method. After coating, the precursor films were annealed in a quartz tube furnace under low vacuum without the use of a Se atmosphere or reduction conditions. Evolution of the morphology, crystal structure, and thermal decomposition behavior of the films was analyzed by X-ray diffraction, scanning electron microscopy, and thermogravimetric analysis, and the film formation mechanism was suggested. The as-deposited precursor film gradually decomposed with increase in temperature and formed Cu_2−xSe and In₂Se₃ nuclei on the surface of the film. Incorporation of Cu_2−xSe with In₂Se₃ yielded a chalcopyrite CIS phase, which crystallized on annealing above 400 °C. The obtained CIS film showed low-resistive ohmic behavior with a Mo electrode and a high absorption efficiency for visible–infrared (IR) light, making it suitable for use in photovoltaic applications.     

Electrical characterisation of SrTiO3/Si interfaces

Deposition of SrTiO₃ (STO) thin films by ultra-high vacuum rf magnetron sputtering was performed in order to produce high-quality STO/p-Si (1 0 0) interfaces and STO insulator layers with high dielectric constants. The deposition temperatures were in the range from room temperature to 550 °C. Capacitance-voltage (C-V) and conductance-frequency measurements showed that the dielectric constant of the films ranges from 55 to 120. C-V measurements on Al/STO/p-Si structures clearly revealed the creation of metal-insulator-semiconductor diodes. The interface state densities (D_it) at the STO/p-Si interfaces were obtained from admittance spectroscopy measurements. The samples deposited at lower temperatures revealed values of D_it between 2×10¹¹ and 3.5×10¹² eV⁻¹ cm⁻² while the higher temperature deposited samples had a higher D_it ranging between 1×10¹¹ and 1×10¹³ eV⁻¹ cm⁻². The above results were also well correlated to X-ray diffraction measurements, Rutherford backscattering spectroscopy, and spectroscopic ellipsometry.     

The effects of annealing temperature on photoluminescence of silicon nanoparticles embedded in SiNx matrix

The effects of the annealing temperature on photoluminescence (PL) of non-stoichiometric silicon nitride (SiN_x) thin films deposited by plasma enhanced chemical vapor deposition (PECVD) using ammonia and silane mixtures at 200 °C were investigated. The optical property and the chemical composition of the films annealed at different temperatures were investigated by PL spectroscopy and Fourier transform infrared absorption spectroscopy (FTIR), respectively. Based on the PL results and the analyses of the bonding configurations of the films, the light emission is attributed to the quantum confinement effect of the carriers inside silicon nanoparticles and radiative defect-related states. These results provide a better understanding of optical properties of silicon nanoparticles embedded in silicon nitride films and are useful for the application of nanosize silicon semiconductor material.     

Structural,electrical and optical properties of SnO2 films deposited on Y-stabilized ZrO2 (1 0 0) substrates by MOCVD

SnO₂ films have been deposited on Y-stabilized ZrO₂ (YSZ) (1 0 0) substrates at different substrate temperatures (500–800 °C) by metalorganic chemical vapor deposition (MOCVD). Structural, electrical and optical properties of the films have been investigated. The films deposited at 500 and 600 °C are epitaxial SnO₂ films with orthorhombic columbite structure, and the HRTEM analysis shows a clear epitaxial relationship of columbite SnO₂(1 0 0)||YSZ(1 0 0). The films deposited at 700 and 800 °C have mixed-phase structures of rutile and columbite SnO₂. The carrier concentration of the films is in the range from 1.15×10¹⁹ to 2.68×10¹⁹ cm⁻³, and the resistivity is from 2.48×10⁻² to 1.16×10⁻² Ω cm. The absolute average transmittance of the films in the visible range exceeds 90%. The band gap of the obtained SnO₂ films is about 3.75–3.87 eV.     

Synthesis and characterization of hafnium oxide and hafnium aluminate ultra-thin films by a sol–gel spin coating process for microelectronic applications

Currently there are intense industry-wide efforts in searching for new high dielectric constant (high-k) materials for use in future generations of ultra-large scale integrated circuits (ULSI). There are number of requirements for the new high-k materials, such as high dielectric constant, thermal stability (400 °C or higher), high mechanical strength, and good adhesion to neighboring layers. Oxide spinels comprise a very large group of structurally related compounds many of which are of considerable technological significance. Spinels exhibit a wide range of electronic and magnetic properties in particular nickel, hafnium, cobalt, containing spinels. In the present investigation, crack free, dense polycrystalline monoclinic structure of pure HfO₂, and Al₂HfO₅ ultra-thin films have been prepared by a simple and cost effective sol–gel spin coating method. The formation of the monoclinic HfO₂ phase at 600 °C and complete formation of the single phase Al₂HfO₅ at 800 °C has been reported. The composition of the annealed films has been measured and found to be 70 at.% of O, 30 at.% of Hf for HfO₂ and 22 at.% of Al, 12 at.% of Hf and 66 at.% of O for Al₂HfO₅ films, which are close to the stoichiometry of the HfO₂ and Al₂HfO₅ thin films.     

Influence of metal organic and inorganic precursors on spray pyrolyzed ceramic MgO (2 0 0) thin films for epitaxial over layers

The MgO (2 0 0) surface is widely used as a substrate for epitaxial growth of superconducting and ferro-electric films. Highly oriented, single crystalline, extremely flat and transparent MgO films have been successfully deposited on quartz substrates by the chemical spray pyrolysis technique using economically viable metal organic and inorganic precursors under optimized conditions at the substrate temperature of 600 °C. Thermal analysis (TGA/DTA) in the temperature range 30-600 °C with the heating rate of 10 °C/min revealed the decomposition behavior of the precursors and confirmed the suitable substrate temperature range for film processing. The heat of reaction, ΔH due to decomposition of metal organic precursor contributed additional heat energy to the substrate for better crystallization. The intensity of the (2 0 0) peak in X-ray diffraction (XRD) measurements and the smooth surface profiles revealed the dependency of precursor on film formation. The compositional purity and the metal-oxide bond formation were tested for all the films. UV-Vis-NIR optical absorption in the 200-1500 nm range revealed an optical transmittance above 80% and the absorption edge at about 238 nm corresponding to an optical band gap E_g = 5.25 eV. Scanning electron microscopy (SEM) and atomic force microscopy (AFM) micrographs of MgO films confirmed better crystallinity with larger grain size (0.85 μm) and reduced surface roughness (26 nm), respectively.