低温化学浴制备PbS薄膜和表征及其在太阳能电池中的应用（英文）

为得到高质量的PbS薄膜,使用化学浴沉积法在40℃、50℃和60℃的低温下在包覆有TiO 2层的FTO衬底上成功制备了PbS薄膜。所制备的PbS薄膜外观光滑、致密,使用X射线衍射、场发射扫描电镜、紫外可见近红外和紫外光电子能谱分析了该薄膜。根据分析结果,运用谢乐公式计算得到以上温度下制备的PbS薄膜的粒径分别为30nm、36 nm和39 nm,且相应禁带宽度分别估算为1.58 eV、1.38 eV和1.20 eV。通过紫外光电子能谱结果计算出相应功函数分别为-4.90 eV、-4.60 eV和-4.50 eV,结合PbS薄膜的禁带宽度和功函数计算了其导带边和价带边的大小。此外,以spiro-OMeT AD作为空穴传输层,制备了PbS/TiO 2太阳能电池,并获得了0.24%的光电转换效率。     

沉积温度对电沉积PbS薄膜结构和性能的影响

采用电沉积法在ITO导电玻璃表面沉积了PbS薄膜,并用X射线衍射仪(XRD)、原子力显微镜(AFM)以及傅立叶变换红外光谱仪(FT-IR)对薄膜的结构和光学性能进行了表征,研究了沉积温度对薄膜的相组成、显微形貌以及光学性质的影响.结果表明:在U=3 V,pH=2.5,T=60 ℃,沉积时间为20 min,加入EDTA作络合剂的情况下,可制备出沿(111)和(200)晶面取向生长的立方相PbS薄膜.薄膜显微结构均匀而致密,随着反应温度从20 ℃增加到60 ℃,薄膜内的压应力逐渐减小,禁带宽度也随着变小.所制备的微晶PbS薄膜的禁带宽度约为0.39 eV.     

镓掺杂对二氧化钛薄膜光吸收性能的影响

通过向TiO2粉体中加入质量分数为1;～15;的Ga2O3粉末,制备了Ga掺杂的TiO2陶瓷靶,并采用脉冲激光沉积法(PLD)用陶瓷靶制备出TiO2薄膜,将薄膜于800～1000℃下退火.对薄膜结构和光学性质的研究表明1000℃退火条件下浓度为1; Ga2O3掺杂能有效将金红石相TiO2的禁带宽度减小至2.62 eV,使其吸收边红移动至470 nm.     

磁控溅射PbSe薄膜厚度对其结构及光学特性的影响

本文利用射频磁控溅射法在200℃的玻璃衬底上沉积了纳米晶PbSe薄膜,薄膜厚度分别为200 nm、250 nm、500 nm及600 nm.利用X射线衍射仪(XRD)、原子力显微镜(AFM)及紫外-可见分光光度计,分别研究了不同厚度PbSe薄膜的晶体结构、表面形貌和光学特性.结果表明:随膜厚增大,PbSe (200)晶面的择优取向显著增强,薄膜的结晶质量逐渐提高.此外,随薄膜厚度增加吸收边发生红移.膜厚为200nm、250 nm时,薄膜的禁带宽度为1.89 eV和1.60 eV;膜厚较大(500 nm及600 nm)时,带隙宽度减小至1.41 eV和1.34 eV,与太阳的光谱辐射更加匹配.因此,我们认为厚度较大的PbSe薄膜更适于用做太阳能电池的吸收层.     

pH值对电沉积PbS薄膜结构和性能的影响

采用阴极恒电压法在ITO导电玻璃表面沉积了PbS薄膜,并用X射线衍射仪(XRD)、原子力显微镜(AFM)以及傅立叶变换红外光谱仪(FT-IR)对薄膜的结构和光学性能进行了表征,研究了沉积液pH值对薄膜的相组成、显微形貌以及光学性质的影响.结果表明:在U=3 V,pH=2.4,沉积时间为20 min,加入EDTA作络合剂的情况下,可制备出沿(111)和(200)晶面取向生长的立方相PbS薄膜.薄膜均匀而致密,随pH值增加,薄膜的压应力及禁带宽度呈现先减小后增大的变化趋势.所制备的微晶PbS薄膜的禁带宽度约为0.38～0.39 eV.     

化学浴法制备CdS薄膜及其光电性能研究

本文用氯化镉、氯化铵、硫脲和氨水的溶液体系采用化学浴沉积法合成CdS薄膜,制备出均匀、致密的CdS薄膜,通过XRD、SEM、EDS、紫外可见吸收光谱等表征手段研究了CdS薄膜的晶体结构,表面形貌,元素比例和光电性能.发现在不同水浴温度下都成功制备了CdS薄膜,其中75℃制备的CdS薄膜最为均匀致密且其XRD衍射峰强度最强,光吸收边在500 nm附近,禁带宽度大约为2.52 eV.这些CdS薄膜的光电响应大,暗态及光照下的电导率分别为1×10-4S·cm-1和1.04×10-2 S · cm-1.用它们制备的CdS/CZTS异质结太阳电池具有明显的光伏效应.     

衬底温度对磁控溅射法制备掺Ta氧化锌薄膜性能的影响

采用射频磁控溅射法,在不同的衬底温度下制备了钽(Ta)掺杂的氧化锌(ZnO)薄膜,采用X射线能谱(EDS)、X射线衍射(XRD)、扫描电镜(SEM)、紫外-可见分光光度计和光致发光(PL)光谱研究了衬底温度对制备的Ta掺杂ZnO薄膜的组分、微观结构、形貌和光学特性的影响.EDS的检测结果表明,Ta元素成功掺入到了ZnO薄膜;XRD图谱表明,掺入的Ta杂质是替代式杂质,没有破坏ZnO的六方晶格结构,随着衬底温度的升高,(002)衍射峰的强度先增大后降低,在400℃时达到最大;SEM测试表明当衬底温度较高时(400℃和500℃),Ta掺杂ZnO薄膜的晶粒明显变大;紫外-可见透过光谱显示,在可见光范围,Ta掺杂ZnO薄膜的平均透光率均高于80;,衬底不加热时制备的Ta掺杂ZnO的透光率最高;制备的Ta掺杂ZnO薄膜的禁带宽度范围为3.34~3.37eV,衬底温度为500℃时制备的Ta掺杂ZnO薄膜的禁带宽度最小,为3.34eV.PL光谱表明衬底温度为500℃时制备的Ta掺杂ZnO薄膜中缺陷较多,这也是造成薄膜禁带宽度变小的原因.     

原子层沉积与磁控溅射法制备TiO2薄膜性能对比研究

分别采用原子层沉积(ALD)和磁控溅射法(MS)在Si和石英衬底上制备TiO2薄膜,并进行退火处理.利用X射线衍射仪(XRD)、扫描电子显微镜(SEM)、原子力显微镜(AFM)和紫外分光光度计对这两种方法制备薄膜的晶型结构、表面形貌和光学特性进行分析对比.结果显示,对于沉积态TiO2薄膜,ALD-TiO2和MS-TiO2未能检测到TiO2衍射峰.ALD-TiO2为颗粒膜,其表面粗糙,颗粒尺寸大;MS-TiO2薄膜表面平整.经退火后,两种方法制备的TiO2薄膜能检测到锐钛矿A(101)衍射峰,但结晶质量不高.受薄膜表面形貌和晶型结构等因素影响,退火前后ALD-TiO2透过率与MS-TiO2透过率变化不一致.对于沉积态和退火态薄膜的禁带宽度,ALD-TiO2分别为3.8eV和3.7 eV,吸收边带发生红移,MS-TiO2分别为3.74 eV和3.84 eV,吸收边带发生蓝移.     

Ag,N共掺锐钛矿TiO2电子结构和光学性质的第一性原理研究

基于密度泛函理论(DFT)的第一性原理研究了未掺杂,Ag、N单掺杂及Ag-N共掺杂锐钛矿TiO2的晶体结构,电子结构及光学特性.研究结果表明,掺杂后锐钛矿TiO2晶胞膨胀,晶格发生明显畸变;Ag-N共掺杂TiO2禁带中引入新的杂质能级,导带下移,禁带宽度减小到1.34 eV,TiO2的光吸收带边发生明显红移,在紫外区和可见光区的吸收系数增大,提高了TiO2的光催化效率.     

生物质改性纳米TiO2的制备及其结构表征

采用溶胶-凝胶法制备了系列生物质改性复合纳米TiO2.以亚甲基蓝溶液为模拟污染物,考察了其可见光催化活性,并确定了最佳制备工艺.通过X射线光电子能谱(XPS)、X射线衍射(XRD)、场发射扫描电镜(FESEM)、紫外-可见漫反射光谱(UV-Vis-DRS)、荧光光谱(PL)等手段对催化剂样品进行了表征.实验结果表明,催化剂对亚甲基蓝的光催化降解适应一级反应动力学,复合TiO2和纯TiO2的反应速率常数分别为0.4990 h-1和0.0305 h-1,且复合催化剂实现了C、N、S、P、K等多元素的共掺杂.相比纯TiO2,复合TiO2的比表面积增大,结晶度升高,光生载流子复合率降低,吸收边带红移,禁带宽度窄化了0.09 eV.     

Syntheses and structures of N-phenylmaleimidetriazoles and by-products

The syntheses, properties, and structures of N-phenylmaleimidetriazole derivatives are described. Intermediates and by-products are also discussed. 1b. a = 43.997(7) Å, 5.7610(9) Å, 8.245(1) Å, = 99.339(4), C₂/c; 2a. a = 13.646(4) Å, b = 7.744(2) Å, c = 10.612(3) Å, = 91.979(6), P2₁/c. 3a. a = 22.245(1) Å, b = 22.245(1) Å, 10.010(1) Å, P42/n. 3a. a = 11.727(2) Å, b = 14.075(3) Å, c = 16.080(3) Å, = 105.859(3), = 105.331(3), = 98.187(3), P-1. 3b. a = 8.561(3) Å, b = 14.755(5) Å, c = 22.771(7) Å, = 97.006(5), P2₁/c. 3c. a = 10.500(2) Å, b = 12.189(2) Å, c = 13.040(2) Å, = 109.091(3), = 106.089(3), = 101.022(3), P-1. 8a. a = 16.389(8) Å, b = 5.749(3) Å, c = 19.316(3) Å, = 97.467(9), P2₁/n. 8b. a = 5.822(2) Å, b = 10.114(3) Å, c = 16.705(4) Å, = 84.681(5), = 82.840(5), = 75.769(4), P-1. 9b. a = 11.251(1) Å, 13.335(3) Å, 13.376(3) Å, = 102.456(4), P2₁/n. 9c. a = 15.836(3) Å, b = 8.236(2) Å, c = 5.447(3) Å, = 92.551(3), P2₁/c. 10a. a = 13.177(2) Å, b = 14.597(2) Å, c = 5.5505(8) Å, = 110.979(2), Cc. 11a. a = 14.720(2) Å, b = 13.995(2) Å, c = 38.245(6) Å, = 94.430(3), P2₁/n. 12b. a = 15.067(5) Å, b = 20.378(6) Å, c = 8.669(5) Å, = 99.16(4), = 99.32(3), = 105.23(3), P-1. 13b. a = 8.2824(6) Å, b = 10.5245(7) Å, c = 15.518(1) Å, = 92.305(1), = 100.473(1), = 100.124(1), P-1. 15a. a = 15.357(3) Å, b = 7.778(2) Å, c = 22.957(2) Å, Pbca. 16b. a = 18.0384(4) Å, b = 12.474(3) Å, c = 20.078(5) Å, Pbca.     

Sol-gel synthesis and characterization of adsorbent and photoluminescent nanocomposites of starch and silica

Using sol-gel method, mesoporous and photoluminescent silica nanocomposites of soluble starch have been synthesized and characterized. Different ratios of H₂O, TEOS and EtOH were used at fixed template (soluble starch) and catalyst (NH₄OH) concentrations to obtain materials of different performances in terms of heavy metal binding from a solution which has been monitored using Cd(II) as representative divalent heavy metal ion. Optimum material was obtained when H₂O, TEOS and EtOH were used in 14:1:2 ratio. This sample was not only an efficient metal ion adsorbent but also had an intense luminescence in ultra-violet region and potentially may be used in silicon-based UV-emitting devices. Metal binding by the material was further enhanced after calcination (at 800 °C in air) while its luminescence had a multipeak profile in UV-visible region. In a batch adsorption study, calcined hybrid composite (0.25 g/L) could remove 98.5% Cd(II) from 100 mg/L Cd(II) solution in 2 h. The chemical, structural and textural characteristics of the synthesized materials have been investigated using Fourier Transform Infrared Spectroscopy (FTIR), X-rays Diffraction (XRD), Thermal Analysis (TGA/DTA), Photoluminescence (PL), Brunauer-Emmett-Teller Analysis (BET) and Scanning Electron Microscopy (SEM).     

Chemistry and Electrocrystallization of Organic Metals and Superconductors

Abstract

Considerable variation in the conditions of electrochemical crystal growth of TMTSF₂X (i.e., constant current versus constant potential, ambient versus inert atmosphere, etc.) and in the purity of the constituents (donor, electrolyte, solvent) does not significantly affect the unusual low-temperature properties of this class of materials. Our results suggest that the electrocrystallization procedure may be self-purifying by selecting for conducting crystal phases with constituents having specific oxidation potentials and solubility properties. However, doping solutions with structurally and chemically similar constituents (i.e., TMTTF, and IO^? ₄ in CIO^? ₄) leads to their incorporation in the crystal structure where they have a profound effect. Several mole percent of these dopants suppress superconductivity in the PF^? ₆ and CIO^? ₄ salts, and increase and broaden the metal-insulator phase transition.     

晶体中负离子配位多面体结晶方位、形变与晶体压电、铁电性

本文研究了压电、铁电晶体中负离子配位多面体的结晶方位与形变,提出了压电晶体中同一种负离子配位多面体的结晶方位是一致的.在铁电晶体中,负离子配位多面体发生形变,伴随着晶体发生顺电-铁电相变,并从这一基本过程出发,对铁电体相变的形成机理进行了讨论.     

Biocrystallization in Bacterial and Fungal Cells and Spores

A series of X-ray diffraction experiments were performed for the first time to study stress-induced biocrystallization (structural response to stress) in the bacteria E. coli, the spore-forming bacteria Bacillus cereus, and in cells and spores of the mycelial fungus Umbelopsis ramanniana. High-intensity areas with spacings of 90 and 44 Å are indicative of a periodically ordered arrangement (most likely nanocrystalline) of the bacterial nucleoid. For the starved bacteria Bacillus cereus, a peak at a spacing of 45 Å is also assigned to nanocrystalline complexes of DNA with the Dps protein. The spores of the fungus Umbelopsis ramanniana VKM F-582, as well as the spores of Bacillus cereus, form ordered arrays of DNA molecules with DNA-condensing acid-soluble proteins SASPs. Starved dehydrated mycelial cells of the fungus Umbelopsis ramanniana form ordered structures with spacings from 27 to 55 Å. A series of peaks reflect the formation of a number of ordered protein arrays, apparently with DNA, with continuously varying characteristic interplanar spacings.     

Preparation and characterization of PbSe nanopowder and quasi-ceramics

By means of the reduction of Pb(II) and Se(IV) with hydrazine, oval monodispersed PbSe nanoparticles characterized by sizes ～100 nm and the cubic symmetry were obtained. Their compaction and sintering into quasi-ceramic state were performed. The samples were investigated by means of scanning electron microscopy, X-ray diffraction and FTIR spectroscopy. The results obtained are discussed.     

Crystal and molecular structures of benz-p-nitroanilide and benz-p-methoxyanilide

The crystal structures of the two carboxylic amides C₁₃H₁₀N₂O₃ (I) and C₁₄H₁₃NO₂ (II) have been determined by direct methods and refined by full-matrix least squares. The predominant structural feature is the hydrogen bonding (N-H?O=C) which influences the conformations of both structures.     

Melting and short-range order in liquids and glasses

A theory is proposed to explain two-dimensional melting based on the gauge-invariant Lagrangian with spontaneous breaking (Higgs mechanism) or the SU(2) gauge field to U(1) symmetry. The first-order phase transition in two-dimensional melting may be strongly related to the asymptotic freedom-like interaction of the SU(2) gauge field in the case when the distance between each excited disk is shorter than a critical length, 2/ boxv;mboxv, near the melting temperature.     

Structural and spectral studies of N-trans-cinnamylidene-m-toluidine and N-trans-cinnamylidene-m-chloroaniline

N-trans-cinnamylidene-m-toluidine (1) C₁₆H₁₅N, and N-trans-cinnamylidene-m-chloroaniline (2) C₁₅H₁₂NCl form isomorphous crystals which are monoclinic, space group P2_l/c, with unit cell dimensionsa=5.967(2),b=13.793(3),c=15.048(5) Å, =91.97(3)° anda=5.868(2),b=13.788(4),c=15.191(4) Å, =91.87(3)°, respectively. The single-crystal X-ray structure determinations of the title compounds revealtrans structures. Ring (A) C_10–15 and ring (B) C_1–6, are practically planar in both structures with dihedral angels of 61.3(3) and 63.6(2)°, respectively.¹H nmr, u.v. and i.r. spectra are also reported.     

Broken Symmetries and Hydrodynamics of Hexatic B and Snectic F and I Liquid Crystal Phases

The nature of the spontaneously broken symmetries in hexatic B and smectic F and I phases is investigated and the hydrodynamics of the associated degrees of freedom is discussed.