Electrical and dielectric properties of MnF2–ZnF2–NaPO3 glasses

Direct electrical conductivity and dependencies of complex electrical modulus vs. temperature and frequency have been measured on glasses from the MnF₂–ZnF₂–NaPO₃ system. These glasses are sensitive to atmospheric humidity and as a consequence, the electrical conductivity increases up to temperature of 50 °C. A hydrated layer is created by the effect of water and leads to the significant increase of the electrical conductivity in the case of 0MnF₂–20ZnF₂–80NaPO₃ glass. This behavior is governed by Arrhenius relation where the values of activation energy are increasing and values of the electrical conductivity are decreasing with the amount of MnF₂. Dielectric measurements show that a heterogeneous phase is formed in the bulk of glasses. This may be seen when plotting complex electrical modulus in the complex plane. The records made by the light microscope confirmed the occurrence of the other phase in the bulk of glasses.     

Thermal and optical properties of TeO2–ZnO–BaO glasses

We report the results of a systematic study of the thermal and optical properties of a new family of tellurite glasses, TeO₂–ZnO–BaO (TZBa), as a function of the barium oxide mole fraction and compare them with those of TeO₂–ZnO–Na₂O (TZN). The characteristic temperatures of this new glass family (glass transition, T_g, crystallization, T_x, and melting, T_m) increase significantly with BaO content and the glasses are more thermally stable (greater ΔT = T_x ? T_g) than TZN glasses. Relative to these, Raman gain coefficient of the TZBa glasses also increases by approximately 40% as well as the Raman shift from ~ 680 cm^? 1 to ~ 770 cm^? 1. The latter shift is due to the modification of the glass with the creation of non-bridging oxygen ions in the glass network. Raman spectroscopy allows us to monitor the changes in the glass network resulting from the introduction of BaO.     

Piezoelectric and elastic properties of ZnF2–PbO–TeO2: TiO2 glass ceramics

Piezoelectric coefficients d₃₃ as well as ultrasonic velocities and elastic coefficients of ZnF₂–PbO–TeO₂ glasses crystallized with different concentrations of TiO₂ (0.5 to 2.0 wt.%) were measured. The contribution to the piezoelectric coefficients is attributed to presence of Pb₅Ti₃F₁₉, PbTiO₃ and PbTeO₃ ferroelectric crystal phases. The piezoelectric coefficients show substantial sensitivity to presence of TiO₂. The ultrasonic velocities and the related elastic coefficients in these glass ceramics as a functions of concentration of nucleating agent TiO₂ exhibited minimal effect at 1.0 wt.%. This is ascribed to the larger presence of titanium ions in Ti³⁺ states which act as modifiers and finally de-polymerize glass ceramic network. The results have been further discussed quantitatively within a framework of different oxidation states of titanium ions and the nature of the crystal phases ingrained in the glass ceramic.     

Raman and NMR study of bioactive Na2O–MgO–CaO–P2O5–SiO2 glasses

The results of a structural study combining NMR and Raman spectroscopy of several melt-derived glasses in the system Na₂O–MgO–CaO–P₂O₅–SiO₂ are presented. The Raman spectra show clear changes in the Si–O–Si vibrational modes (related to the bridging oxygen atoms, BO) and also verify the presence of non-bridging oxygen atoms (NBO), also named terminal oxygens. The intensity of the Si–O–NBO stretching mode depends on the cation concentration. It can be concluded from the NMR studies that the MgO-containing samples have orthophosphate units charge-compensated by Ca²⁺ and Mg²⁺. The silicate matrix also contains both types of two-valent cations and consists of Q² and Q¹ units. Similarly, the Na₂O-containing samples contain isolated orthophosphate units in a silicate matrix (Q² and Q³ units), both charge-compensated by mixed cations Ca²⁺ and Na⁺. These experimental data were compared with theoretical parameters given by the Stevels model, which is a suitable tool for understanding bioactive behavior of these glasses. Furthermore, results of the in vitro tests carried out in simulated body fluids are presented and compared with both Raman and NMR structural data.     

The effect of TiO2 on phase separation and crystallization of glass-ceramics in CaO–MgO–Al2O3–SiO2–Na2O system

The experiments were carried out on studying the effect of phase separation on nucleation and crystallization in the glass based on the system of CaO–MgO–Al₂O₃–SiO₂–Na₂O. In the experiments, TiO₂ was chosen as nucleating agent. Three batches of 5, 8 and 10 wt% TiO₂ substitution were investigated by the techniques of DSC, XRD, FTIR and FESEM equipped with EDS. XRD and FTIR analysis indicated that the super cooled glasses were all amorphous, the heat treatment leading to nucleation would cause a disruption of silica network which followed phase separation. The phase separation followed the generation of crystal seeds Mg(Ti, Al)₂O₆. FESEM observation and EDS analysis revealed that the more TiO₂ content of glass, the more droplet separated phase and crystal seeds after nucleation heat treatment. The main crystal phase is clinopyroxene, Ca(Ti, Mg, Al)(Al, Si)O₆, of crystallized glass.     

Influence of thermal and thermoelectric treatments on structure and electric properties of B2O3–Li2O–Nb2O5 glasses

A transparent glass with the composition 60B₂O₃–30Li₂O–10Nb₂O₅ (mol%) was prepared by the melt quenching technique. The glass was heat-treated with and without the application of an external electric field. The as-prepared sample was heat-treated (HT) at 450, 500 and 550 °C and thermoelectric treated (TET) at 500 °C. The following electric fields were used: 50 kV/m and 100 kV/m. Differential thermal analysis (DTA), X-ray diffraction (XRD), scanning electron microscopy (SEM), Raman, dc and ac conductivity, as a function of temperature, were used to investigate the glass and glass-ceramics properties. LiNbO₃ crystals were detected, by XRD, in the 500 °C HT, 550 °C HT and 500 °C TET samples. The presence of an external electric field, during the heat-treatment process, improves the formation of LiNbO₃ nanocrystals at lower temperatures. However, in the 550 °C HT and in the TET samples, Li₂B₄O₇ was also detected. The value of the σ_dc decreases with the rise of the applied field, during the heat-treatment. This behavior can indicate an increase in the fraction of the LiNbO₃ crystallites present in these glass samples. The dc and ac conduction processes show dependence on the number of the ions inserted in the glass as network modifiers.The Raman analysis suggests that the niobium ions are, probably, inserted in the glass matrix as network formers.These results reflect the decisive effect of temperature and electric field applied during the thermoelectric treatment in the structure and electric properties of glass-ceramics.     

Influence of valence and coordination of manganese ions on spectral and dielectric features of Na2SO4–B2O3–P2O5 glasses

Sodiumsulpho borophosphate glasses with composition (40 ? x)Na₂SO₄–30B₂O₃–30P₂O₅: xMnO with x ranging from 0 to 5.0 mol% were manufactures. Dielectric spectra have been studied over a wide frequency range of 10²–10⁵ Hz and in the temperature range within 30–250 °C. The valance states of manganese ions and their ligand coordination in the glass network have been investigated using optical absorption, luminescence and ESR spectroscopy. The analysis of the these results has indicated that the manganese ions exist both in Mn²⁺ as well as in Mn³⁺ states and occupy prevailingly octahedral positions and serve as modifiers similarly to Na⁺ ions The values of dielectric parameters (dielectric constant, ε′(ω), loss tan δ and ac conductivity, σ_ac) were found to increase with increasing MnO content. They play a role of modifiers similarly to Na⁺ ions, create bonding defects and free ions viz., [SO₄]^2?, [POO_1/2O₂]^2?, [POO_0/2O₃]^3–, Na⁺ and (NaSO₄)^?. The migration of these charge carriers would build up space charge polarization and may be responsible for the enhanced dielectric parameters. The ac conductivity also is enhanced with increasing MnO content. The mechanism responsible for such increase is well explained based on the modifying action of Mn²⁺ ions.     

Structure and properties of NaPO3–ZnO–Nb2O5–Al2O3 glasses

In an effort to design low-melting, durable, transparent glasses, two series of glasses have been prepared in the NaPO₃–ZnO–Nb₂O₅–Al₂O₃ system with ZnO/Nb₂O₅ ratio of 2 and 1. The addition of ZnO and Nb₂O₅ to the sodium aluminophosphate matrix yields a linear increase of properties such as glass transition temperature, density, refractive index and elastic moduli. The chemical durability is also significantly, but nonlinearly, improved. The glass with the highest niobium concentration, 55NaPO₃–20ZnO–20Nb₂O₅–5Al₂O₃ was found to have a dissolution rate of 4.5 × 10^? 8 g cm^? 2 min^? 1, comparable to window glass. Structural models of the glasses were developed using Raman spectroscopy and nuclear magnetic resonance spectroscopy, and the models were correlated with the compositional dependence of the properties.     

Characteristics and biocompatibility of Na2O–K2O–CaO–MgO–SrO–B2O3–P2O5 borophosphate glass fibers

A novel Na₂O–K₂O–CaO–MgO–SrO–B₂O₃–P₂O₅ borophosphate glass fiber is prepared. The thermal properties including differential thermal analysis (DTA) and viscosity measurement of the glass were presented. The tensile strength of the glass fiber is measured. The reaction of the glass fibers in the SBF solution is characterized by XRD, FTIR and SEM. XRD and FTIR indicate that the carbonate hydroxyapatite has formed rapidly on the glass. Cell attachment, spreading and proliferation on the glass are determined by MTT [3-(4,5-Dimethylthiazol-2-yl)-2,5-Diphenyltetrazolium Bromide] assay method using Human osteosarcoma MG-63 cells. The bioactivity and biocompatibility of the glass fiber make it a good potential prospect in the field of tissue engineering.     

The role of coordination and valance states of tungsten ions on some physical properties of Li2O–Al2O3–ZrO2–SiO2 glass system

A series of Li₂O–Al₂O₃–ZrO₂–SiO₂ glasses doped with different concentrations of WO₃ (0 to 5.0 mol.%) have been synthesized. Differential thermal analysis of the samples indicated increasing glass forming ability with the increasing concentration of WO₃ in the glass matrix. A variety of spectroscopic (optical absorption, IR, Raman and ESR) and dielectric properties (over a range of frequency and temperature) of these glasses have been investigated. The optical absorption and ESR spectral studies have pointed out that a part of tungsten ions do exist in W⁵⁺ state in addition to W⁶⁺ state especially in the samples containing low concentration of WO₃. The IR and Raman spectral studies have suggested that there is a decreasing degree of disorder in the glass network with increase in the concentration of WO₃. The values of dielectric parameters viz., dielectric constant, loss and ac conductivity at any frequency and temperature are observed to decrease as the concentration of WO₃ is increased. Such changes have been attributed to decrease of redox ratio or decreasing proportions of W⁵⁺ ions that act as modifiers in the glass network. The quantitative analysis of the results of ac conductivity and dielectric properties have indicated an increase in the insulating character of the glasses with the concentration of WO₃; this is attributed to the presence of tungsten ions largely in W⁶⁺ ions that participate in the glass network forming with WO₄ structural units.     

Microstructure and thermal properties of the GeS2–In2S3–CsI glassy system

A new series of chalcohalide glasses in the GeS₂–In₂S₃–CsI pseudo-ternary system were prepared by conventional melt-quenching method. The glass-forming region was determined and it is mainly situated in the GeS₂-rich domain. The glasses have relatively high glass transition temperatures (T_g ranges from 335 to 405 °C) and good thermal stabilities. Based on the Raman spectra, it can be speculated that the glassy net is mainly constituted by [GeS₄] and [InS_4?xI_x] tetrahedra, which are interconnected by the bridging sulfur atoms. And the ethane-liked structural units [S₃Ge–GeS₃] can be formed because of the lacking of sulfur. Cs⁺ ion, which was added from CsI, exists as the nearest neighbor of I^? ion.     

Second-order optical non-linearity initiated in Li2O–Nb2O5–SiO2 and Li2O–ZnO–Nb2O5–SiO2 glasses by formation of polar and centrosymmetric nanostructures

Amorphous nanoheterogeneities of the size less than 100 Å have been formed in glasses of the Li₂O–Nb₂O₅–SiO₂ (LNS) and Li₂O–ZnO–Nb₂O₅–SiO₂ (LZNS) systems at the initial stage of phase separation and examined by transmission electron microscopy, small-angle X-ray and neutron scattering. Both LNS and LZNS nanoheterogeneous glasses exhibit second harmonic generation (SHG) even when they are characterized by fully amorphous X-ray diffraction (XRD) patterns. Chemical differentiation and ordering of glass structure during heat treatments at appropriate temperatures higher T_g lead to drastic increase of SHG efficiency of LNS glasses contrary to LZNS ones in the frame of amorphous state of samples. Following heat treatments of nanostructured glasses result in crystallization of ferroelectric LiNbO₃ and non-polar LiZnNbO₄ in the LNS and LZNS glasses, respectively. Taking into account similar polarizability of atoms in LNS and LZNS glasses, the origin of the principal difference in the second-order optical non-linearity of amorphous LNS and LZNS samples is proposed to connect predominantly with the internal structure of formed nanoheterogeneities and with their polarity. Most probably, amorphous nanoheterogeneities in glasses may be characterized with crystal-like structure of polar (LiNbO₃) phase initiating remarkable SHG efficiency or non-polar (LiZnNbO₄) phase, which do not initiate SHG activity. It gives an opportunity to vary SHG efficiency of glasses in a wide rage without remarkable change of their transparency by chemical differentiation process at the initial stage of phase separation when growth of nanoheterogeneities is ‘frozen’. At higher temperatures, LiNbO₃ crystals identified by XRD precipitate in LNS glasses initiating even more increase of SHG efficiency but visually observable transparency is impaired.     

Synthesis and characterization of CoFe2O4–PVP nanocomposites

Cobalt ferrite–poly(N-vinyl-2-pyrrolidone) nanocomposites were prepared by drying a dispersion of cobalt ferrite (CoFe₂O₄) nanoparticles and poly(N-vinyl-2-pyrrolidone). Magnetic measurements indicate a superparamagnetic behavior. Zero-field-cooling magnetization experiments at 100 Oe show different trends depending on the CoFe₂O₄ nanoparticles size. For the smaller ones (3.9 nm), the blocking temperatures shift to lower temperatures with increasing concentration; however, this shift is not observed for the larger ones (6.6 nm). These differences can be related to the anisotropy constant of the CoFe₂O₄ nanoparticles and the interparticle dipolar interactions.     

Effect of alumina on the structure and properties of Li2O–B2O3–P2O5 glasses

The structure of glasses within the system Li₂O–Al₂O₃–B₂O₃–P₂O₅ has been studied through ³¹P, ¹¹B and ²⁷Al Nuclear Magnetic Resonance, and the effect of Al₂O₃ substitution by B₂O₃ and P₂O₅ network formers on the structure and properties investigated for a constant Li₂O content. Multinuclear NMR results reveal that substitution of Al₂O₃ for B₂O₃ and P₂O₅ network formers in a glass with composition 50Li₂O·15B₂O₃·35P₂O₅ produces a change in boron environment from four-fold to three-fold coordination. Meanwhile aluminum can be present in four-, five- and six-fold coordinations a higher amount of Al(IV) groups is found for increasing alumina contents. The behavior of the glass transition temperature and electrical conductivity of the glasses has been interpreted as a function of the structural changes induced in the glass network when alumina is substituted for B₂O₃, P₂O₅ or both. Small additions of alumina produce a drastic increase in glass transition temperature, while it does not change for [Al₂O₃] greater than 3 mol.%. However, the electrical conductivity shows very different behavior depending on the type of substitution; it can remain constant when B₂O₃ content decreases or sharply decrease when P₂O₅ is substituted by Al₂O₃, which is attributed to a higher amount of BO₃ and phase separation.     

Structural role and coordination environment of Fe in Fe2O3–PbO–SiO2–Na2O composite glasses

The structural role, coordination geometry and valence of Fe in a series of Fe₂O₃–PbO–SiO₂–Na₂O glasses are studied by means of Fe-K-NEXAFS and EXAFS spectroscopies. Parameters for the study are the concentration of the Fe and Pb-oxides, the SiO₂/Na₂O ratio and the cast temperature. The EXAFS and NEXAFS results reveal that the role of Fe³⁺ depends on the concentration of Fe₂O₃. More specifically, in most of the studied quaternary systems, the Fe³⁺ ion is a glass former, i.e. the Fe atoms belong to FeO₄ tetrahedra that participate in the formation of the glassy network. The role of Fe as an intermediate oxide is identified only in one sample with 20 wt% Fe₂O₃, where ～80 at.% of the Fe atoms are tetrahedrally coordinated with O atoms, while the remaining ～20 at.% of the Fe atoms occupy octahedral sites. It is also revealed that the tetrahedral coordination of Fe in the vitreous matrix is destroyed when a number of parameters is altered, such as the T_cast, the (Fe + Si)/O and the SiO₂/Na₂O ratio.     

Synthesis and photoluminescence of Eu3+-doped ZnO–Ga2O3–SiO2 nano-glass-ceramics

Transparent rare-earth Eu³⁺-doped ZnO–Ga₂O₃–SiO₂ nano-glass-ceramics were obtained by a sol–gel method. X-ray diffraction and transmission electron microscopy were used to characterize the as-synthesized materials. Results showed that ZnGa₂O₄ nanocrystals with the size of 5 nm were precipitated from ZnO–Ga₂O₃–SiO₂ system and dispersed in the SiO₂-based glass when the heat-treatment temperature was up to 800 °C. Photoluminescence characterization of Eu³⁺-doped ZnO–Ga₂O₃–SiO₂ nano-glass-ceramics was carried out and the results show that the as-synthesized material display intense emission at 615 nm belonging to ⁵D₀ → ⁷F₂ transition.     

Synthesis and bioactive properties of macroporous nanoscale SiO2–CaO–P2O5 bioactive glass

A macroporous nanoscale bulk bioactive glass (SiO₂–CaO–P₂O₅ system) was prepared by sol–gel co-template method. Porosimeter analysis showed that the as-synthesized bioactive glasses (BGs) had a porosity of 85% and exhibited a multimodal pore size distribution, nanopores (10–40 nm) and macropores (100 nm–10 μm). Morphological and structural characterizations showed the pores were interconnected with pore walls of about 250 nm in width and 1 μm in length. In vitro bioactivity test indicated that the as-synthesized bulk BGs exhibited faster apatite layer formation capability than the conventional sol–gel BGs. Additionally, the deposited layer was identified as hydroxycarbonate apatite, which is similar to the inorganic part of human bone.     

Preparation and properties of chalcogenide glasses in the GeS2–Sb2S3–CdS system

In searching for new kind of photoelectric material, chalcogenide glasses in the GeS₂–Sb₂S₃–CdS system have been studied and their glass-forming region was determined. The system has a relatively large glass-forming region that is mainly situated along the GeS₂–Sb₂S₃ binary side. Thermal, optical and mechanical properties of the glasses were reported and the effects of compositional change on their properties are discussed. These novel chalcogenide glasses have relatively high glass transition temperatures (T_g ranges from 566 to 583 K), good thermal stabilities (the maximum of deference between the onset crystallization temperature, T_c, and T_g is 105 K), broad transmission region (0.57–12 μm) and large densities (d ranges from 2.99 to 3.34 g cm^?3). These glasses would be expected to be used in the field of rare earth doped fiber amplifiers and nonlinear optical devices.     

Formation and structure of crystalline inclusions in As2S3–SbSI and As2Se3–SbSI systems glass matrices

The main aim of the study presented in this paper is the investigation of the structure of (As₂S₃)_100?x(SbSI)_x and (As₂Se₃)_100?x(SbSI)_x (0 ≤ × ≤ 40) glasses by Raman spectroscopy and X-ray methods, also the nature of the crystalline inclusions which arise up in their matrix at heat treatment. We have found that in conditions of continuous heating in the interval “glassforming temperature–crystallization temperature” a crystallization with predominant mechanism of stable phase SbSI separation is taking place. The formation mechanism of crystalline inclusions of antimony sulphoiodide in glass matrix is discussed in the light of our results. It was established that all investigated glasses have a nano-heterogeneous structure.     

Structural investigations of nitrided Nb2O5 and Nb2O5–SiO2 sol–gel derived films

Sol–gel derived xNb₂O₅–(100 ? x)SiO₂ films (where x = 100, 80, 60, 50, 40, 20, 0 mol%) were nitrided at various temperatures (800 °C, 900 °C, 1000 °C, 1100 °C and 1200 °C). The structural transformations occurring in the films as a result of ammonolysis were studied using X-ray diffraction (XRD), atomic force microscopy (AFM) and X-ray photoelectron spectroscopy (XPS). The XRD results have shown that the temperatures below 1100 °C were too low to obtain a pure NbN phase in the samples. The AFM observations indicate that the formation of the NbN phase and the size of NbN grains are related to the silica content in the layer. NbN grains become more regular and larger as the niobium content increases. The maximum grain size of about 100 nm was observed for x = 100. Preparation of the Nb₂O₅–SiO₂ sol–gel derived layers and the subsequent nitridation is a promising method of inducing crystalline NbN in amorphous matrices. It follows from the XPS results that a small amount of Nb₂O₅ remains in the films after nitridation at 1200 °C and that nitrogen reacted not only with Nb₂O₅ but also with SiO₂.