含裂纹梁非线性静动力特性及简化动力学建模

主要研究裂纹对梁结构动力特性的影响规律,进而为含裂纹梁结构状态监测提供理论依据。首先,对裂纹影响区域进行分析,建立含裂纹梁二维接触非线性有限元模型,阐明含裂纹梁具有拉压不同刚度的静力特性;其次,通过对机理模型的分析,指出拉压不同刚度会引起轴向与弯曲的耦合振动;然后,通过非线性动力学分析方法研究其动力特性,观察到含裂纹梁在冲击荷载下会产生轴向与弯曲的耦合振动现象,并指出这种轴向与弯曲耦合振动的一个重要特征是轴向振动频谱图中含有弯曲振动基频的两倍频成分;最后,通过引入非线性弹簧建立一种新颖的含裂纹梁简化动力学模型,通过与精细有限元分析对比,验证了模型的合理性。该简化动力学模型将接触非线性问题转换为材料非线性问题,避免了费时的接触非线性动力学求解过程。     

两种典型螺栓连接结构的刚度特性比较研究

针对法兰对接和径向套接两种典型舱段螺栓连接形式,基于有限元静刚度计算、动力学简化建模、冲击响应特性分析及结构冲击试验,系统研究了两种连接形式的轴向刚度特性及其对动力学冲击响应的影响.有限元静刚度分析揭示了法兰对接与径向套接的轴向拉压刚度分别是非对称的和对称的,而法兰对接的平均刚度更大.之后,为两种连接形式建立了统一的动力学模型,证明非对称的轴向拉压刚度导致结构在受到横向载荷作用时会产生附加的耦合轴向振动,并且利用高精度幂函数拟合刚度跳变,得到耦合轴向振动频率是弯曲振动频率的二倍的结论.最后,通过冲击动力学试验证明了法兰对接存在二倍频的耦合轴向振动,而径向套接则不存在该耦合振动.径向套接虽然一阶频率较低,但阻尼效果更好.     

基于旋转软化的柔性梁动力学研究

建立了旋转柔性梁的非线性动力学模型,利用能量法及哈密顿原理导出了耦合的动力学方程,分析了转动惯性、Coriolis力、应力刚化、旋转软化、加速度、横向位移、弯曲刚度等作用效应;通过设置应力刚化及旋转软化等刚度矩阵和编制有限元程序,建立了梁单元有限元模型,对柔性梁在旋转软化状态下的振动模态进行了数值模拟与分析。计算表明:梁的旋转软化导致其沿旋转平面的弯振模态(摆振)频率随转速增大而相对下降,且对第一阶摆振频率的影响最显著,呈现非线性;梁的旋转软化对垂直于旋转平面的弯振频率几乎没有影响,此结果表明了旋转柔性梁动态特性的复杂性,因此在计算旋转柔性梁的振动特性时,必须同时设置平动、转动惯性质量矩阵,才能获得准确结果。此外,梁单元模型与实体单元模型计算结果误差小于等于5%,验证了本文梁单元模型求解方法的准确性。     

含轴向运动效应的裂纹梁横向振动频率研究

针对含轴向运动效应开口裂纹梁,借助裂纹梁连续等效刚度模型,将裂纹效应引入轴向运动梁的横向振动方程.应用传递矩阵法推导了求解其振动频率的特征方程,计算得到裂纹和运动参数连续变化情况下梁的一阶和二阶固有频率数值解.对裂纹和轴向运动参数对梁的振动频率的联合影响机理进行了分析,研究表明,对于梁的一阶和二阶固有频率,轴向运动速度和裂纹深度具有耦合作用效应.裂纹加深使得由轴向速度带来的频率衰减加速;同时,速度提升导致由裂纹引起的频率衰减变得更加剧烈.相较于二阶频率,耦合作用效应对于一阶频率表现得更加显著.     

旋转悬臂梁的刚柔耦合动力学建模与频率分析

对固结于转动刚体上外接柔性梁的刚柔耦合动力学建模和频率特性进行了研究,在精确描述柔性梁非线性变形的基础上,利用Hamilton变分原理和假设模态法,在计入柔性梁由于横向变形而引起的轴向变形二阶耦合量的条件下,推导出考虑"动力刚化"项的一次近似耦合模型。首先忽略柔性梁纵向变形的影响,给出一次近似简化模型,引入无量纲变量,对简化模型做无量纲化处理,分析梁固有频率对模态截断数的依赖性;其次研究在一次近似简化模型和零次近似简化模型下,调谐角速度与共振现象的关系;最后分析一次近似耦合模型的动力特性。研究发现,为保证计算的精度,模态截断数应随无量纲角速度的增大而增加,合理的模态截断数具有收敛值;一次近似简化模型下悬臂梁横向弯曲振动不存在共振调谐角速度,一次耦合模型下柔性梁并没有出现屈曲失稳现象。现有典型文献的相关结论是值得商榷的。     

考虑非线性变形的航天器柔性附件建模方法

针对航天器的柔性附件,将其简化为常见的大范围运动空间柔性梁结构。根据柔性体的非线性变形原理,考虑了弯曲和扭转的非线性因素的影响,在柔性梁的三个变形方向上均考虑了变形的二次耦合项。利用有限元方法进行离散并用Lagrange方程建立了非线性变形模式下的动力学方程,包含了较为完全的刚度矩阵和各种耦合项。对一大范围运动的空间梁进行了仿真计算,表明在运动速度较大并且基座具有大范围运动时,一次耦合模型与本文模型有一定差异,且初始变形对两种模型也会产生影响。     

含旋转运动效应裂纹梁横向振动特性的研究

针对开口裂纹作用下旋转运动欧拉-伯努力梁的振动特性进行了研究。文中使用裂纹梁连续等效刚度模型模拟裂纹效应,将含裂纹旋转运动梁视为弯曲刚度沿梁长度方向连续变化的梁,并应用传递矩阵法推导了求解其振动特性的特征方程。考虑不同裂纹深度和位置、不同旋转速度,分析了梁的一阶和二阶固有频率的变化情况。研究结果表明:旋转运动效应和裂纹效应并非独立影响梁的固有频率,两者间具有耦合作用效应;转速提升使由裂纹导致的频率衰减幅度变小,同时裂纹加深使得由速度升高带来的阶频提升更加显著;相比于二阶频率,耦合作用效应对于一阶频率更加显著。     

核主泵叶轮间隙的轴向振动特性研究

具有径向流的间隙结构广泛存在于轴承结构与旋转机械中，间隙中的流固耦合作用可能影响整体结构的运动稳定性。基于理论间隙模型和核主泵的实际结构，本文对径向间隙流引起的轴向振动进行了多方面的研究。当间隙的一个壁面产生轴向振动并处于旋转状态时，壁面受到由径向流引起的时变轴向力，因此间隙为叶轮提供附加的轴向刚度和阻尼。通过研究以水为介质的理论间隙模型，发现径向间隙流会引起负的等效轴向动力系数（刚度和阻尼），并且流道形状是影响间隙轴向动力特性的重要因素。扩张流道和平行流道会产生负的轴向动力系数，特别是负阻尼会引起结构振动发散；而收缩流道间隙具有稳定的轴向动力特性。最后，对AP1000核主泵原型叶轮间隙模型进行分析，结果表明，间隙会引起轴向负刚度，并且在一定工况下出现负阻尼，此时系统轴向稳定性及结构安全运行将受到严重的不良影响。     

旋转运动柔性梁的假设模态方法研究

采用假设模态法对旋转运动柔性梁的动力特性进行研究，给出简化的控制模型. 首先采用Hamilton原理和假设模态离散化方法，在计入柔性梁由于横向变形而引起的轴向变形的二阶耦合量的条件下，推导出基于柔性梁变形位移场一阶完备的一次近似耦合模型，然后对该模型进行简化，忽略柔性梁纵向变形的影响，给出一次近似简化模型，最后将采用假设模态离散化方法的结果与采用有限元离散化方法的结果进行了对比研究. 研究中考虑了两种情况：非惯性系下的动力特性研究和系统大范围运动为未知的动力特性研究. 研究结果显示，当系统大范围运动为高速时，在假设模态离散化方法中应增加模态数目，较少的模态数目将导致较大误差. 一次近似简化模型能够较好地反映出系统的动力学行为，可用于主动控制设计的研究.     

超低频振动能量收集器中夹片弹簧结构的建模与验证

针对一类基于夹片弹簧的压电振动能量收集器，利用材料力学莫尔积分理论建立了振荡俘能结构中夹片弹簧的等效刚度模型，通过万能拉伸试验机验证了模型精度。在此基础上，讨论了夹片弹簧刚度线性简化的两种途径：拉伸曲线线性拟合和固有频率修正。研究结果表明，从夹片弹簧拉伸曲线上看，将其等效成线性弹簧具有一定的合理性；而在实际振动能量收集器结构中，若振动加速度相对较小，通过固有频率修正法对夹片弹簧刚度进行线性简化，其幅频响应特性与非线性模型的特性相近。该研究成果为压电振动能量收集器的动力学和机电耦合模型简化提供了理论支撑。     

Investigation on dynamic characteristics of a rod fastening rotor-bearing coupling system with fixed-point rubbing

The aim of this paper is to gain insight into the nonlinear vibration feature of a dynamic model of a gas turbine. First, a rod fastening rotor-bearing coupling model with fixed-point rubbing is proposed, where the fractal theory and the finite element method are utilized. For contact analysis, a novel contact force model is introduced in this paper. Meanwhile, the Coulomb model is adopted to expound the friction characteristics. Second, the governing equations of motion of the rotor system are numerically solved, and the nonlinear dynamic characteristics are analyzed in terms of the bifurcation diagram, Poincaré map, and time history. Third, the potential effects provided by contact degree of joint interface, distribution position, and amount of contact layer are discussed in detail. Finally, the contrast analysis between the integral rotor and the rod fastening rotor is conducted under the condition of fixed-point rubbing.

     

Nonlinear dynamic force transmissibility of a flywheel rotor supported by angular contact ball bearings

The dynamic force transmissibility (DFT) of aerospace flywheel rotor system (FRS) supported by angular contact ball bearings (ACBBs) is examined in this paper. The influence of combined loads and contact angle variation is considered in the Sjovall formula to accurately solve the load distribution and nonlinear stiffness of ACBB. Subsequently, the lateral vibration model of FRS is established by considering the nonlinear stiffness characteristics of ACBB. The DFT of the system is solved via harmonic balance method and arc length continuation, and the stability of the results is determined. Numerical integration and dynamic tests are utilized to verify the accuracy of harmonic balance results. Based on the proposed model, the effects of rotor unbalance excitation, axial preload, and rotor damping on the DFT of the system are discussed. The soft-stiff transition phenomenon is observed in terms of the varying supporting stiffness of ACBB wherein deformation is measured under axial preload. The value of rotor unbalanced mass determines the nonlinear characteristics of FRS. The results provide an important reference for dynamic performance evaluation and vibration isolation device design of aerospace FRS.

     

Influences of wear on dynamic characteristics of angular contact ball bearings

Wear between balls and races has significant effects on the dynamic characteristics of bearing, which is the main reason to cause bearing failure. Some existing contact stiffness models were established to study the dynamic characteristics of bearing. However, the wear of bearing has been rarely investigated due to the complexities of contact load and wear mechanism. This paper presents a new dynamic wear simulation model of angular contact ball bearings mounted in pairs to solve this problem. A final contact stiffness model is established based on the wear model. The effects of running distance, horizontal load, preload, initial contact angle, number and diameter of balls on wear performances are analyzed. A generalized time-varying and piecewise-nonlinear dynamic model of angular contact ball bearings is established to perform an accurate investigation on its dynamic characteristics, especially considering the coupling effects of wear and rolling contact. The effects of wear on the contact stiffness and nonlinear dynamic characteristics are analyzed according to the dynamic model. Additionally, the variations of the contact stiffnesses and frequency responses with different preloads are discussed and the results indicate that parameter selection has significant effects on the wear and nonlinear response.

     

The dynamic stiffness matrix of the finite annular plate element

The dynamic deformation of harmonic vibration is used as the shape functions of the finite annular plate element, and sonic integration difficulties related to the Bessel’s functions are solved in this paper. Then the dynamic stiffness matrix of the finite annular plate element is established in closed form and checked by the direct stiffness method. The paper has given wide convcrage for decomposing the dynamic matrix into the power series of frequency square. By utilizing the axial symmetry of annular elements, the modes with different numbers of nodal diameters at s separately treated. Thus some terse and complete results are obtained as the foundation of structural characteristic analysis and dynamic response compulation.     

预应力混凝土平面杆系结构的有限元方法

建立了基于有限元方法的考虑材料和几何非线性的任意截面预应力混凝土平面杆系结构的数值分析模型，可用于模拟预应力混凝土大跨度梁、单向偏压细长柱等的非线性全过程结构响应。引入修正的Rodriguez截面模型确定截面切线刚度，其中混凝土的贡献通过截面边界顶点定义的梯形单元来实现；在此基础上利用传统的平面非线性杆单元导出了标准有限元公式。通过两个算例验证了该模型的可靠性和适用性。     

非线性压电效应下压电弯曲执行器的动力分析

研究压电弯曲执行器在强电场作用下的非线性动力行为．考虑电致伸缩和电致弹性的非线性压电效应，导出了压电悬臂执行器变刚度的弯曲振动控制方程．利用非定常振动的渐近理论，讨论了弯曲压电执行器的动力特征．根据目前的非线性模型可以计算压电悬臂执行器的固有共振频率与电场的变化关系．结果表明压电执行器端头挠度谐振幅度随作用电场振幅的增大而增大，以及力学品质因数随电场振幅的增大而减少，并且与实验结果非常吻合．通过数值比较得到在电场频率随时间变化非常缓慢的情况下非定常振动问题可以近似地用定常振动来处理．     

Nonlinear dynamic behavior analysis of an elastically restrained double-beam connected through a mass-spring system that is nonlinear

Some complex engineering structures can be modeled as multiple beams connected through coupling elements. When the coupling element is elastic, it can be simplified as a mass-spring system. The existing studies mainly concentrated on the double-beam coupled through elastic connectors, where the connector is simplified as the equivalent linear stiffness element or linear mass-spring system. Furthermore, many researches ignore rotational boundary restraints in analyzing dynamic behavior of the double-beam connected through elastic connectors, limiting their engineering generality. Considering the above limitations, this study attempts to employ the cubic nonlinear stiffness in the coupling mass-spring system and study the potential application of the mass-spring system that is nonlinear on the vibration control of the double-beam system. Using the variational method and the generalized Hamiltonian method build the corresponding system’s governing functions. Applying the Galerkin truncation method (GTM) obtains the dynamic behavior of the double-beam connected through a mass-spring system that is nonlinear. According to this study, the change of the mass-spring system that is nonlinear significantly influences the dynamic behavior of the double-beam system, where the complex dynamic behavior occurs under certain parameters of the mass-spring system that is nonlinear. Suitable parameters of the mass-spring system that is nonlinear are good at the vibration suppression at the boundary of the vibration system. Furthermore, the mass-spring system that is nonlinear can change the characteristics of the double-beam system’s kinetic energy transfer. For the vibration model established in this work, a quasi-periodic vibration state can be regarded as a sign of the occurrence of the targeted energy transfer of the double-beam connected through a mass-spring system that is nonlinear.

     

ANCF索梁单元应变耦合问题与模型解耦

索粱结构在土木工程、航空航天等领域有着广泛的应用.在各类索梁动力学建模方法中,由于绝对节点坐标方法(absolute nodal coordinate formulation,ANCF)能够描述柔性体的大变形和大转动问题,因此非常适合大变形索梁结构的动力学建模.对绝对节点坐标索梁单元的应变进行分析可知,弯曲变形会引起单元内部轴向应变的不均匀分布,即单元轴向应变与弯曲应变相互耦合.这种应变耦合效应使单元产生伪应变能,导致单元刚度增大,造成单元失真.分析不同弯曲角下的单元应变及应变能可知,弯曲变形越大,单元失真越严重.通过构造等效一维杆单元重新描述轴向应变,实现了轴向应变与弯曲应变解耦.在此基础上推导广义弹性力,得到了绝对节点坐标索梁单元的应变解耦模型.对解耦前后的两种梁模型进行静力学和动力学仿真,结果表明;解耦模型消除了单元伪应变,相比原模型表现出更好的收敛性和曲率连续性,在相同单元数目下具有更高的精度.同时由于解耦模型降低了单元刚度,因此相比原模型,速度曲线中不再有高频振动.     

任意高差的多档输电线动刚度理论建模

针对目前多档输电线动力特性研究中存在的不足,将任意一档导线视为子结构并基于现有的索振动理论获得了其动张力;利用相邻两档导线的动张力建立了悬垂绝缘子串绕其悬挂点摆动的动力学方程;综合每一档导线的振动方程以及悬垂绝缘子串的摆动方程建立了两档及三档输电线的动力学方程,求解得到由端部位移激励产生的动刚度;通过对动刚度进行分析得到了多档输电线的固有频率以及模态的理论表达形式;建立了小高差的两档及三档导线的有限元模型,理论分析结果与有限元结果一致,验证了理论公式的正确性。本文提出的动刚度理论对于研究多档输电线的动态响应具有重要的应用价值。