Experimental investigation on the distribution uniformity and pressure drop of perforated plate distributors for the innovative spray-type packed bed thermal storage

As an innovative thermal energy technology,the spray-type packed bed has advantages of high efficiency and low cost.A liquid distributor is the key component fo...     

INVESTIGATION INTO MALDISTRIBUTION IN A CIRCULATING FLUIDIZED BED

1. Introduction The design of gas distributor has a major influence on gas flow patterns, dumping and dead zones. It has been demonstrated that maldistribution will occur if the distribu-tor has a low pressure drop, that is, some parts of the bed will receive much less gas than others, and may be tem-porarily or permanently defluidized, while the gas forms semi-permanent spouts or channels in other parts. There-fore, maldistribution is undesirable in industry. For example, the temperature in a…     

Extrudate Trilobe Catalysts and Loading Effects on Pressure Drop and Dynamic Liquid Holdup in Porous Media of Trickle Bed Reactors

The hydrodynamics of concurrent gas-liquid downflow through a porous media of fixed bed reactor has been studied experimentally in a range of trickling flow rates. A pilot bed is packed with industrial spherical and extrudate trilobe catalysts. The industrial trilobe catalysts are packed in a bed using two different methods: random close or dense packing and random sock packing. The experiments are performed for single phase in the cases of wet and dry packed beds and for two-phase flow conditions. The comparisons of pressure drops as well as liquid holdup are carried out for the above three different porous media, random close, dense packing and random sock packing. It is shown that the pressure drop of the dense loaded bed is higher than that of spherical particles which have approximately the same porosity. The results also revealed that the bed porosity, shape and contact points of the loaded catalyst have significant effects on the dynamic liquid holdup of the TBRs. Finally, a new correlation was developed for dynamic liquid holdup and pressure drop calculation for trilobe dense and sock catalyst beds and beds which are loaded with spherical particles.     

Two-phase flow distributors for fuel cell flow channels

All existing proton exchange membrane （PEM） fuel cell gas flow fields have been designed on the basis of single-phase gas flow distribution. The presence of liquid water in the flow causes non-uniform gas distribution, leading to poor cell performance. This paper demonstrates that a gas flow restrictor/distributor, as is commonly used in two-phase flow to stabilize multiphase transport lines and multiphase reactors, can improve the gas flow distribution by significantly reducing gas real-distribution caused by either non-uniform water formation in parallel flow channels or flow instability associated with negative-slope pressure drop characteristic of two-phase horizontal flow systems.     

Hydrodynamics of a bubble-induced inverse fluidized bed reactor with a nanobubble tray

This paper reports on the hydrodynamics of a bubble-induced inverse fluidized bed reactor, using a nanobubble tray gas distributor, where solid particles are fluidized only by an upward gas flow. Increasing the gas velocity, the fixed layer of particles initially packed at the top of the liquid starts to move downwards, due to the rise of bubbles in this system, and then gradually expands downwards until fully suspended. The axial local pressure drops and standard deviation were examined to delineate the flow regime comprehensively under different superficial gas velocities. Four flow regimes (fixed bed regime, initial fluidization regime, expanded regime, and post-homogeneous regime) were observed and three transitional gas velocities (the initial fluidization velocity, minimum fluidization velocity, and homogeneous fluidization velocity) were identified to demarcate the flow regime. Three correlations were developed for the three transitional velocities. As the fine bubbles generated from the nanobubble tray gas distributor are well distributed in the entire column, the bed expansion process of the particles is relatively steady.     

Flow of Newtonian and Non-Newtonian Fluids Through Packed Beds: An Experimental Study

The phenomena of flow reduction and flow enhancement was observed in case of viscoelastic and viscoinelastic fluids flowing through packed beds, respectively. In this study, the pressure drop-flow rate behaviors for the flow of Newtonian (water), non-Newtonian viscoinelastic (Carboxy methyl cellulose solution in water, CMC) and viscoelastic (Polyacrylamide solution in water, PAA) fluids have been experimentally studied and pressure drop behavior compared with existing models for viscoinelastic and viscoelastic fluids. Based on the observed data, an appropriate empirical correlation for pressure drop prediction in case of non-Newtonian fluid flowing through packed bed has been proposed. The correlation predicts the data well to within a reasonable accuracy.     

An experimental study of electrorheological fluid flow through a packed bed of glass beads

This paper shows that pressure drop-flow rate performance of an electrorheological (ER) fluid flowing through a packed bed of glass beads is consistent with a modified Ergun equation for yield stress flow through a packed bed. ER fluids are of scientific and engineering interest due to the sensitivity of their rheological properties on the applied electric field. As far as we know ER fluids have not been studied for flows through porous media. In this work a silica particle–silicone oil suspension is pumped through a rectangular packed bed of glass beads with applied electric fields. The silica particles are observed to form fibrous structures parallel to the electric field that stretch between the beads and extend between the electrodes. The pressure drop-flow rate performance agrees well with the expected performance calculated from a modified Ergun equation for a yield stress fluid flow through the packed bed with the viscosity and yield stress as functions of the applied electric field.     

Modelling the flow of power law fluids in a packed bed using a volume-averaged equation of motion

The development of a theoretical model for the prediction of velocity and pressure drop for the flow of a viscous power law fluid through a bed packed with uniform spherical particles is presented. The model is developed by volume averaging the equation of motion. A porous microstructure model based on a cell model is used. Numerical solution of the resulting equation is effected using a penalty Galerkin finite element method. Experimental pressure drop values for dilute solutions of carboxymethylcellulose flowing in narrow tubes packed with uniformly sized spherical particles are compared to theoretical predictions over a range of operating conditions. Overall agreement between experimental and theoretical values is within 15%. The extra pressure drop due to the presence of the wall is incorporated directly into the model through the application of the no-slip boundary condition at the container wall. The extra pressure drop reaches a maximum of about 10% of the bed pressure drop without wall effect. The wall effect increases as the ratio of tube diameter to particle diameter decreases, as the Reynolds number decreases and as the power law index increases.     

Flow Maldistribution in Dense- and Sock-Loaded Trilobe Catalyst Trickle-Bed Reactors: Experimental Data and Modeling Using Neural Network

In order to experimentally study the catalyst loading method (dense and sock) influence on liquid distribution, a trickle-bed reactor (TBR) packed with extrudate trilobe catalysts was used. Furthermore, an artificial neural network (ANN) algorithm has been applied; the results show acceptable agreement between the ANN model prediction and experimental data. Due to the isotropic distribution of porosity in sock-loaded bed with trilobe catalysts, the results illustrate that with the same operating conditions the sock-packed beds spread liquid better than dense ones. The effects of bed height and variations of gas/liquid flow rate on liquid distribution in sock- and dense-loaded TBRs have been investigated.     

Flow regime transitions due to cavitation in the flow through an orifice

This paper presents both experimental and theoretical aspects of the flow regime transitions caused by cavitation when water is passing through an orifice. Cavitation inception marks the transition from single-phase to two-phase bubbly flow; choked cavitation marks the transition from two-phase bubbly flow to two-phase annular jet flow.

It has been found that the inception of cavitation does not necessarily require that the minimum static pressure at the vena contracta downstream of the orifice, be equal to the vapour pressure liquid. In fact, it is well above the vapour pressure at the point of inception. The cavitation number [σ = (P₃ − P_v)/(0.5 pV²); here P₃ is the downstream pressure, P_v is the vapour pressure of the liquid, ρ is the density of the liquid and V is the average liquid velocity at the orifice] at inception is independent of the liquid velocity but strongly dependent on the size of the geometry. Choked cavitation occurs when this minimum pressure approaches the vapour pressure. The cavitation number at the choked condition is a function of the ratio of the orifice diameter (d) to the pipe diameter (D) only. When super cavitation occurs, the dimensionless jet length [L/(D - d); where L is the dimensional length of the jet] can be correlated by using the cavitation number. The vaporization rate of the surface of the liquid jet in super cavitation has been evaluated based on the experiments.

Experiments have also been conducted in which air was deliberately introduced at the vena contracta to simulate the flow regime transition at choked cavitation. Correlations have been obtained to calculate the critical air flow rate required to cause the flow regime transition. By drawing an analogy with choked cavitation, where the air flow rate required to cause the transition is zero, the vapour and released gas flow rate can be predicted.     

Modeling fluid and heat transport in the reactive, porous bed of downdraft (biomass) gasifier

A fluid flow and heat transfer model has been developed for the reactive, porous bed of the biomass gasifier to simulate pressure drop, temperature profile in the bed and flow rates. The conservation equations, momentum equation and energy equation are used to describe fluid and heat transport in porous gasifier bed. The model accounted for drag at wall, and the effect of radial as well as axial variation in bed porosity to predict pressure drop in bed. Heat transfer has been modeled using effective thermal conductivity approach. Model predictions are validated against the experiments, while effective thermal conductivity values are tested qualitatively using models available in literature. Parametric analysis has been carried out to investigate the effect of various parameters on bed temperature profile and pressure drop through the gasifier. The temperature profile is found to be very sensitive to gas flow rate, and heat generation in oxidation zone, while high bed temperature, gas flow rate and the reduction in feedstock particle size are found to cause a marked increase in pressure drop through the gasifier. The temperatures of the down stream zones are more sensitive to any change in heat generation in the bed as compared to upstream zone. Author recommends that the size of preheating zone may be extended up to pyrolysis zone in order to enhance preheating of input air, while thermal insulation should not be less than 15 cm.     

Mixed convective heat transfer characteristics and mechanisms in structured packed beds

The structured packed bed is considered a promising reactor owing to its low pressure drop and good heat transfer performance. In the heat transfer process of thermal storage in packed beds, natural convection plays an important role. To obtain the mixed convective heat transfer characteristics and mechanisms in packed beds, numerical simulations and coupling analyses were carried out in this study on the unsteady process of fluid flow and heat transfer. A three-dimensional model of the flow channel in the packed bed was established, and the Navier–Stokes equations and Laminar model were adopted for the computations. The effects of the driving force on fluid flow around a particle were studied in detail. The differences in velocity and density distributions under different flow directions due to effect of the aiding flow or opposing flow were intuitively demonstrated and quantitatively analyzed. It was found that the driving force strengthens the fluid flow near the particle surface when aiding flow occurs and inhibits the fluid flow when opposing flow occurs. The boundary layer structure was changed by the natural convection, which in turn influences the field synergy angle. For the aiding flow, the coordination between the velocity and density fields is higher than that for the opposing flow. By analysis the effects of physical parameters on mixed convective heat transfer, it is indicated that with an increase in the fluid-solid temperature difference or the particle diameter, or a decrease in the fluid temperature, the strengthening or inhibiting effect of natural convection on the heat transfer became more significant.     

Ethanol–CO2 two-phase flow in diverging and converging microchannels

The present study investigates experimentally two-phase flow patterns and pressure drop of ethanol and CO₂ in a converging or diverging rectangular microchannel. The two-phase flow pattern visualization is made possible using a high speed video camera. The increased superficial gas velocity due to the acceleration effect and the large pressure drop in a converging channel may result in the elongation of bubbles in slug flow, while the decreased superficial velocity owing to the deceleration effect and the possible pressure rise in the diverging channel may cause shortening of bubbles in slug flow significantly. For both types of channel, the collision and merger of two consecutive bubbles may take place and result in necking of bubbles. Two-phase flow pressure drop in the converging microchannel increases approximately linearly with the increasing liquid or gas flow rate with the frictional pressure drop being the major contributor to the channel pressure drop. In the diverging microchannel, the deceleration effect results in the pressure rise and counteracts the frictional pressure drop. Consequently, for low liquid flow rates the channel pressure drop increases only slightly with the gas flow rate while it is low and a reversed trend appears while it is high. For high liquid flow rates the effect of increasing gas flow rate on channel pressure drop is much more significant; a more significant reverse trend of the effect of gas flow rate is present in the region of high gas flow rates. The two-phase frictional multiplier in the converging or diverging microchannel is quite insensitive to the liquid flow rate and can be fitted very well within ±15% based on the Lockhart–Martinelli equation with a modified Chisholm parameter for the diverging microchannel and together with a modified coefficient for the X⁻² term for the converging microchannel.     

Equal quality distribution of gas–liquid two-phase flow by partial separation method

This paper proposes a new method for equal quality distribution of gas–liquid two-phase flow by partial separate-phase distribution with a dual-header distributor. The upper and liquid (lower) headers are interconnected with five vertical downward arms. A gas–liquid two-phase mixture enters the distributor from the upper header where most of the liquid of the mixture is removed through the downward arms into the liquid header. Hence, firstly, the remaining gas-rich fluid can be uniformly distributed into the outlet branches, and then secondly, the liquid collected in the liquid header can be uniformly re-distributed into the individual outlet branches. Because both distribution processes are conducted in the condition of single or near single-phase flow, mal-distribution of the two-phase flow is essentially eliminated, and a satisfactory equal quality distribution of gas–liquid two-phase flow is reached. Experiments were conducted in an air–water two-phase flow test loop. The inner diameter of the inlet pipe was 60 mm, the superficial velocity ranges of gas and liquid were 3–32 m/s and 0.02–0.17 m/s respectively, and the quality ranged from 0.02 to 0.44. The flow pattern in the inlet pipe included stratified flow, wavy stratified, slug flow, and annular flow. The experimental results showed that this new method could significantly improve the distribution performance of the two-phase flow. The maximum quality deviation between each outlet branch and the inlet pipe is less than ±1% under the conditions of stratified, wavy stratified and slug flows in the upper header, and less than ±5% in annular flow.     

The hydrodynamics of liquid–liquid upflow through a venturimeter

The present work reports the influence of a venturimeter on liquid–liquid phase distribution during upflow through a vertical pipe. The optical probe technique has been adopted for the characterization of flow. The probability density function and the wavelet multi-resolution analysis of the random probe signals have provided an insight into the details of the flow patterns and the intrinsic differences at the upstream, throat and the downstream sections. The experiments have indicated the flow pattern transitions to occur at lower velocities at the downstream region of the venturi. The pressure drop readings across the venturi have been used to estimate the mass flow rate of the mixture by using suitable models for the different patterns.     

Effect of drag-reducing polymers on pseudo-slugs––interfacial drag and transition to slug flow

Drag-reducing polymers were added to air and water flowing in a stratified configuration in a horizontal 2.54 cm pipe. The interface was covered with large amplitude roll waves, that have been called pseudo-slugs, over a range of flow conditions. The damping of small wavelength waves causes a large decrease in the interfacial stress and, therefore, an increase in the liquid holdup. At superficial gas velocities greater than 4 m/s the transition to slug flow is delayed in that it occurs at larger liquid holdups. This observation is interpreted by assuming that turbulence in slugs is damped. This increases the shedding rate of a slug and, therefore, its stability. The pressure drop can increase or decrease when polymers are added. The increase in holdup is accompanied by an increase in gas velocity, which causes an increase in the pressure drop. The decrease in the interfacial stress has the opposite effect.     

Liquid flow patterns about barbotage bubbles

This paper summarizes the results of a flow visualization study on the liquid motion around barbotage bubbles during growth and departure. Flow patterns, as well as for the first time, instantaneous velocities, are reported as a function of time and location about the bubbles. The experiments, employing the hydrogen-bubble technique and high-speed cine photography, were with: water as the liquid, air as the bubbled gas, orifice diameters of 0.116 and 0.252 cm, and different air flow rates; the two limiting cases of constant supply pressure and constant volumetric flow rate were covered. It was found that the liquid around a barbotage bubble assumes two velocity maxima, the first an outward maximum during bubble growth and the second in the opposite direction approximately at the time of bubble departure; further, liquid velocities were found to be higher close to the bubbling site. Certain differences in liquid velocities between the constant pressure and constant flow cases are explained in terms of available theoretical solutions to the bubble growth rate. Qualitative comparisons of the barbotage liquid flow patterns and those recently reported for boiling flow patterns are also presented.     

Heat Transfer and Pressure loss of a very shallow fluidized-bed heat exchanger Part 1. Experiment with a single row of tubes

A novel gas fluidized-bed heat exchanger with a very small static bed height has been developed for a heat-exchanging system using a low-pressure fan. This fluidized bed is composed of a multislit distributor, a single row of 8 mm diameter tubes, and glass beads 48–195 μm in diameter. The measured performance of heat transfer is excellent and that of fluidization is satisfactory, in spite of the static bed height being as small as 13 mm. In the best case, the test fluidized bed exhibited a heat transfer performance comparable to that of a conventional fluidized bed with a perforated plate distributor and a static bed height of 150 mm, and showed one-fourteenth the pressure loss.     

Surface wettability effect on flow pattern and pressure drop in adiabatic two-phase flows in rectangular microchannels with T-junction mixer

Wettability is an important parameter in micro-scale flow patterns. Previous research has usually been conducted in conventional microtubes due to limitations of visualizing flow patterns and fabricating microchannels. However, most microchannels in practical applications have rectangular shape. Furthermore, pressure drop is closely related with flow pattern. Hence, we studied water liquid and nitrogen gas flows in rectangular microchannels with different wettabilities. The rectangular glass microchannels were fabricated from photosensitive glass, whose surface is hydrophilic. The surface of one was silanized using octadecyl-trichloro-silane (OTS) to prepare a hydrophobic microchannel. The two-phase flow pattern was visualized with a high-speed camera and a long distance microscope. The frictional pressure drop in the microchannel was measured directly with embedded pressure ports. The flow pattern and pressure drop in the hydrophobic microchannel were totally different from those in the hydrophilic microchannel. Finally, the two-phase frictional pressure drop was analyzed based on the flow patterns of different wettabilities.     

The rivulet flow pattern during oil–water horizontal flow through a 12 mm pipe

The present study reports the hydrodynamics of the rivulet pattern during oil–water flow through a 12 mm horizontal acrylic pipe. The interfacial distribution has been observed visually and characterized from signals obtained from an optical probe as well as by isokinetic sampling. The probability density function (PDF) and fast Fourier transform (FFT) of the signals have provided an understanding of the flow configuration. The experiments have revealed that although rivulet flow is a typical separated flow pattern, it has different characteristics as compared to the stratified and annular flow patterns. The holdup and pressure drop under such conditions have been compared with the drift flux model for horizontal flow as well as the two-fluid model as proposed by Brauner and Maron [9] for liquid–liquid flows.