Vortex shedding induced by a solitary wave propagating over a submerged vertical plate

Experimental study was conducted on the vortex shedding process induced by the interaction between a solitary wave and a submerged vertical plate. Particle image velocimetry (PIV) was used for quantitative velocity measurement while a particle tracing technique was used for qualitative flow visualization. Vortices are generated at the tip of each side of the plate. The largest vortices at each side of the plate eventually grow to the size of the water depth. Although the fluid motion under the solitary wave is only translatory, vortices are shed in both the upstream and downstream directions due to the interaction of the generated vortices as well as the vortices with the plate and the bottom. The process can be divided into four phases: the formation of a separated shear layer, the generation and shedding of vortices, the formation of a vertical jet, and the impingement of the jet onto the free surface. Similarity velocity profiles were found both in the separated shear layer and in the vertical jet.     

基于涡量矩理论的绕振荡水翼涡动力学分析

文章采用标准k-ω SST湍流模型和动网格技术, 实现了绕俯仰振荡NACA66水翼非定常流动结构与水动力特性的数值模拟, 并基于有限域涡量矩理论定量表征了局部旋涡结构对水翼动力特性的影响. 研究结果表明: 在水翼升程阶段, 当攻角较小时, 层流向湍流的转捩点由水翼尾缘向前缘移动; 在较大攻角时, 顺时针尾缘涡?TEV在水翼吸力面上生成并向前缘发展, 同时与吸力面上的顺时针前缘涡?LEV融合发展为附着在整个吸力面上的新前缘涡?LEV, 新的?LEV与逆时针尾缘涡+TEV相互作用直至完全脱落, 直接导致了水翼的动力失速, 在回程阶段, 绕振荡水翼的流场结构逐渐由湍流转变为层流. 基于有限域涡量矩理论的定量分析发现, 有限域内附着的?LEV和?TEV提供正升力, 当?LEV发展覆盖整个吸力面时对升力的贡献最大, 占总升力近50%, 而+TEV提供负升力. 同时发现, 有限域内各旋涡内部的不同区域提供的升力有正有负; 而逸出有限域的旋涡内部不同区域提供的升力方向均保持一致, 其中顺时针涡提供正升力, 而逆时针涡提供负升力. 在失速阶段, 域外旋涡整体对升力贡献较小且存在小幅波动, 体现了流动的非定常性.      

激波在平板上诱导的旋涡强度的测量

运动激波通过两个等攻角平板后诱导出两个同向旋转的旋涡，这两个旋涡在随当地气流向下游运动的同时，绕涡核连线中心旋转。本文通过测量涡对的转动角度速度，获得了每个旋涡的强度。实验结果表明，由此测得的旋涡强度不同用于小攻角平板起动涡公式计算了起动涡强度。     

Application of a vortex lattice numerical model in the calculation of inviscid incompressible flow around delta wings

The flow over a flat plate delta wing at incidence and in sideslip is studied using vortex lattice models based on streamwise penelling. For the attached flow problem the effect of sideslip is simulated by modifying the standard vortex lattice model for zero sideslip by aligning the trailing vortices aft of the wing along the resultant flow direction. For the separated flow problem a non-linear vortex lattice model is developed for both zero and non-zero sideslip angles in which the shape and position of the leading edge separation vortices are calculated by an iterative procedure starting from an assumed initial shape. The theoretical values are compared with available theoretical and experimental results.     

Free surface waves in equilibrium with a vortex

Finite amplitude solitary waves of uniform depth which interact with a stationary point vortex are considered. Waves both with and without a submerged obstacle are computed. The method of solution is collocation of Bernoulli's equation at a finite number of points on the free surface coupled with equations for equilibrium of a point vortex. The stream function and vortex location are found by computing a conformal map of the flow domain to an infinite strip. For a given obstacle the solutions are parametrized with respect to Froude number and vortex circulation. When no obstacle is present there are two families of solutions, in one of which the amplitude of the wave increases by increasing the circulation, while in the other amplitude increases by decreasing the circulation. Beyond a certain critical Froude number the maximum amplitude wave has a sharp crest with an angle of 120 degrees. Similar behavior is observed for the flow past a submerged obstacle except that there is a critical Froude number below which there is no solution at all.     

Asymmetric vortex shedding flow past an inclined flat plate at high incidence

This paper reports an experimental investigation of the vortex shedding wake behind a long flat plate inclined at a small angle of attack to a main flow stream. Detailed velocity fields are obtained with particle-image velocimetry (PIV) at successive phases in a vortex shedding cycle at three angles of attack, α=20°, 25° and 30°, at a Reynolds number Re≈5,300. Coherent patterns and dynamics of the vortices in the wake are revealed by the phase-averaged PIV vectors and derived turbulent properties. A vortex street pattern comprising a train of leading edge vortices alternating with a train of trailing edge vortices is found in the wake. The trailing edge vortex is shed directly from the sharp trailing edge while there are evidences that the formation and shedding of the leading edge vortex involve a more complicated mechanism. The leading edge vortex seems to be shed into the wake from an axial location near the trailing edge. After shedding, the vortices are convected downstream in the wake with a convection speed roughly equal to 0.8 the free-stream velocity. On reaching the same axial location, the trailing edge vortex, as compared to the leading edge vortex, is found to possess a higher peak vorticity level at its centre and induce more intense fluid circulation and Reynolds stresses production around it. It is found that the results at the three angles of attack can be collapsed into similar trends by using the projected plate width as the characteristic length of the flow.     

Flows around rotating disks with and without rim-shroud gap

Experimental and numerical approaches have been used to study the effect of the radial rim-shroud gap on the flow structures found around a rotating disk in a finite cylindrical casing. When the radius of the disk and the inner radius of the casing are comparable and there is no radial gap, instabilities bring spiral rolls with a positive front angle in the Bödewadt layer on the end wall of the stationary casing. When the disk radius is smaller than the inner radius of the casing, vortex flows appear within the radial gap between the disk rim and the side wall of the casing. If the disk is thin, but not too thin, disturbances generated by these vortex flows proceed inward and the spiral rolls with a negative front angle appear in the Bödewadt layer. In the case of a thick disk, wavy Taylor vortex-like flow appears in the radial gap. The disturbances formed by the vortex flow do not well propagate into the inner region, and a flow pattern of bead-like vortices or a chain of vortices consisting of a series of small vortices are found around the disk in the visualized figure parallel to the disk.     

On swirl development in a square cross-sectioned, S-shaped duct

The flow in a uniform square cross-sectioned, S-shaped duct was investigated experimentally, at Reynolds number (Re) = 4.73 × 10⁴ and 1.47 × 10⁵, using three S-ducts of different curvature and turning angle. The hydraulic diameter (D) for each S-duct is 150 mm. Besides studying the square cross-sectioned S-duct flow at moderately higher Re than current literature, the S-ducts’ geometry used in this study also have larger curvatures and higher turning angles than those reported in the literature. With surface pressure measurement and smoke wire flow visualization, flow separation at the inside wall of the first bend was detected. Using surface oil flow visualization on the bottom wall of the S-duct and cross-wires measurement at the duct exit, it is shown here that the swirl developed in the first bend was partly attenuated in the second bend due to the formation of swirl of opposite direction. The swirl of an opposite sign results in the formation of a clear dividing or separation line on the bottom wall (and top wall) of the duct. Additional flow features include the formation of streamwise vortices on the outer-wall of the second bend. These streamwise vortices can either be a pair of counter-rotating vortices or a single vortex. The formation mechanism of these streamwise vortices is explained using the Squire and Winter [J Aeronaut Sci 18(4):271–277, 1951] formula and it is shown that the said mechanism is applicable to both Re in the present study.     

Effect of magnetic field on thermal instability in mixed convection flow over a rotating boundary layer

Effect of magnetic field on the formation of longitudinal vortices in mixed convection flow over a rotating heated flat plate is presented. The onset position is characterized by the Grashof number, the rotational number, the Prandtl number, the Eckert number, the magnetic field parameter, and the wave number. Negative rotation (clockwise) and external magnetic field stabilize the boundary layer flow. On the contrary, positive rotation (anti-clockwise), the Eckert number, and the Prandtl number destabilize the flow. The numerical data show agreement with the experimental data with the case of zero Hartmann number in the literature.     

非对称槽道中涡旋波的特性研究

利用PIV流场显示技术，对振荡流体在非对称槽道中涡旋波的产生、发展和消失的规律进 行了实验研究和分析，测得了涡旋波流场的速度矢量图，阐明了涡旋波流场周期性变化的特 点. 结合涡动力学方程，深入分析并揭示了做周期性运动的流体能在槽道中产生波的特性这 一规律，从中发现：流体周期变化的非定常性和不对称的槽道结构是形成涡旋波流动的主要 因素. 本文对涡旋波流场中各个旋涡的速度分布和涡量进行了测量和计算，分析了涡旋波 强化传质的机理，并研究了Re数对涡旋波流动的影响     

On the flow behaviour of confined finite-length wavy cylinders

Confined aspect-ratio of 6 wavy cylinders with a mean blockage-ratio of 0.5 were studied using time-resolved particle-image velocimetry at a sub-critical Reynolds number of 2700. Wavelengths and wave amplitudes of 2–4 and 0.1–0.3 mean diameters respectively were investigated. Results show that vortices are generally shed from the wavy cylinder and channel walls regularly, reminiscent of the unsteady symmetric flow configuration in confined non-wavy cylinders. Furthermore, vortex formation lengths for confined wavy cylinders are generally shorter than their unconfined counterparts, though their variations with respect to geometrical changes remain consistent with unconfined flow conditions. Gross cross-stream flow behaviour does not differ significantly between confined and unconfined wavy cylinders, indicating that finite-length effects are independent of the present confinement. Confined wavy cylinder wake regions are more sensitive towards geometrical changes and a combination of small wavelength and large wave amplitude leads to significant suppression of coherent cylinder and wall vortex-shedding. This is supported by phase-averaged flow reconstructions derived from Proper Orthogonal Decomposition analysis. Lastly, larger wave amplitudes lead to redistributions of dominant flow energy further downstream and to higher mode numbers, which suggests a causal link to the formation of stronger and more coherent streamwise vortices.     

Vortex shedding around a near-wall circular cylinder induced by a solitary wave

This study developed a two-dimensional generalized vortex method to analyze the shedding of vortices and the hydrodynamic forces resulting from a solitary wave passing over a submerged circular cylinder placed near a flat seabed. Numerical results for validation are compared with other numerical and experimental results, and satisfactory agreement is found. A series of simulations were performed to study the effects of gap-to-diameter ratio and incident wave height on vorticity pattern as well as the forces exerted on the cylinder. The range of the heights of incident waves is from 0.3h to 0.7h, where h is the still water depth. The range of the gap-to-diameter ratios is from 0.1 to 0.8. The results indicate that the flow pattern and the pressure distribution change significantly because of the close proximity of the seabed where the vorticity flux on the seabed-side surface of the cylinder is suppressed. Placing the cylinder nearer the seabed increases the drag and the positive lift on the cylinder. When the gap-to-diameter ratio increases, the pattern of vortices changes because of the interaction between the main recirculation zone and the shear layers separated from the gap. The maxima of drag, lift and total force increase linearly with the height of the incident wave.     

Vortex control by the spanwise suction flow on the upper surface of delta wing

The numerical investigation has been performed to explore the feasibility of vortex control by leading edge sucking excitation on a delta wing. The results reveal that the flow on the upper surface of the delta wing changes significantly in a wide range of the angle of attack. For the vortical flow at moderate angle of attack, the secondary and tertiary vortices are weakened or suppressed, and the total lift is almost unchanged. For the stalled flow at high angle of attack, the leading edge concentrated vortex is recovered, and the lift is enhanced with increasing suction rate. For the bluff-body flow at even high angles of attack, the lift can still be improved. The concentrated vortex disappears on the upper surface, and the load increment is nearly unchanged along the chordwise direction. The project supported by the National Natural Science Foundation of China (19802018).     

Study of the flow around surface-mounted pyramids

The turbulent flow around square-based wall-mounted pyramids in thin and thick boundary layers was experimentally investigated as a function of the pyramid apex angle, ‘, and angle of attack, f, based on mean flow surface patterns, pressure and velocity measurements. For thin boundary layers, wake periodicity is observed. For slender pyramids (15°<‘<75°), the periodic formation and shedding of vortices is observed. The shedding frequency scales with the length scale L=w'(w'/h)^-1/4, where h is the pyramid height and w' is the frontal (projected) base width. For broad pyramids, wake periodicity exists but cannot be related to vortex shedding. Vortex shedding appears related to the existence of a double vortex structure along the side faces of the slender pyramids. The location of the separation point upstream and the attachment point downstream of the obstacle also scales with L. For thick boundary layers, no wake periodicity is observed and the mean flow structure in the wake differs from that seen for thin boundary layers. The location of the separation and attachment points scales only approximately with L.     

Strong vortex/boundary layer interactions

This is the second of two papers on the interaction between a longitudinal vortex pair, produced by a delta-wing at angle of attack, and a turbulent boundary layer developing on a flat plate. In the first paper only the outer parts of the vortices entered the boundary layer whereas in this paper the vortices merge with it. In the resultant interaction, the boundary layer between the vortices is kept thin by lateral divergence and a three-dimensional separation line is formed outboard of each vortex. Turbulent, momentum-deficient fluid containing longitudinal vorticity is entrained from the boundary layer along these lines and wrapped around the vortices. As a consequence, the turbulent region of the vortices increases in size and the circulation slowly decreases. It is shown that the flow near the separation line and in the vortices is complicated, and this interaction is expected to be more difficult to calculate than the first. Detailed mean flow and turbulence measurements are reported.     

On the vortex dynamics in the wake of a finite surface-mounted square cylinder

The shedding process in the near wake of a surface-mounted, square cross-section cylinder of height-to-width aspect ratio 4 at a Reynolds number of 12,000 based on free-stream velocity and the obstacle width was investigated. The boundary layer thickness was 0.18 obstacle heights based on 99% free-stream velocity. The study is performed using planar high frame-rate particle image velocimetry synchronized with pressure measurements and hot-wire anemometry. Spatial cross-correlation, instantaneous phase relationships, and phase-averaged velocity data are reported. Two dominant vortex-shedding regimes are observed. During intervals of high-amplitude pressure fluctuations on the obstacle side faces, alternate formation and shedding of vortices is observed (regime A) similar to the von Kármán process. Regime B is characterized by two co-existing vortices in the obstacle lee throughout the shedding cycle and is observed within low-amplitude pressure fluctuation intervals. Despite the coexisting vortices in the base region, opposite sign vorticity is still shed out-of-phase downstream of this vortex pair giving rise to a staggered arrangement of counter-rotating vortices downstream. While the probability of occurrence of Regime B increases toward the free end, the amplitude modulation remains coherent along the obstacle height. Conditionally phase-averaged reconstructions of the flow field are consistent with the spatial distribution of the phase relationships and their probability density function. Earlier observations are reconciled showing that the symmetric shedding of vortices is a rare occurrence.     

Flow of a vortical stream in the neighborhood of the critical point

A study was made of the axisymmetric flow of a viscous incompressible fluid in the neighborhood of the critical point of an obstacle when steady-state vortices oriented in the direction of the angular coordinate are introduced into the oncoming flow. A solution is presented of the equation for the transfer of a vortex in the case of an external flow containing a single largesize vortex in the low-frequency part of the spectrum. Using a finite integral Hankel transform, the problem is reduced to the solution of a system of ordinary differential equations. It is shown that a sufficiently large-size vortex can have a considerable effect on the structure of viscous flow near an obstacle.Translated from Izvestiya Akademii Nauk SSSR, Mekhanika Zhidkosti i Gaza, No. 6, pp. 85–89, November–December, 1970.     

Effect of rotation on the formation of longitudinal vortices in mixed convection flow over a flat plate

This paper presents a numerical study of the effect of rotation on the formation of longitudinal vortices in mixed convection flow over a flat plate. The criterion on the position of marking the onset of longitudinal vortices is defined in this paper. The onset position characterized by the Goertler number G _δ depends on the Grashof number, the rotation number Ro, the Prandtl number Pr and the wave number. The results show that negative rotation stabilizes the boundary layer flow on the surface. On the contrary, positive rotation destabilizes the flow. The numerical data are compared with the experimental results.     

Population,characteristics and kinematics of vortices in a confined rectangular jet with a co-flow

Vortex behavior and characteristics in a confined rectangular jet with a co-flow were examined using vortex swirling strength as a defining characteristic. On the left side of the jet, the positively (counterclockwise) rotating vortices are dominant, while negatively rotating vortices are dominant on the right side of the jet. The characteristics of vortices, such as population density, average size and strength, and deviation velocity, were calculated and analyzed in both the cross-stream direction and the streamwise direction. In the near-field of the jet, the population density, average size and strength of the dominant direction vortices show high values on both sides of the center stream with a small number of counter-rotating vortices produced in the small wake regions close to jet outlet. As the flow develops, the wake regions disappear, these count-rotating vortices also disappear, and the population of the dominant direction vortices increase and spread in the jet. The mean size and strength of the vortices decrease monotonically with streamwise coordinate. The signs of vortex deviation velocity indicate the vortices transfer low momentum to high-velocity region and high momentum to the low velocity region. The developing trends of these characteristics were also identified by tracing vortices using time-resolved particle image velocimetry data. Both the mean tracked vortex strength and size decrease with increasing downstream distance overall. At the locations of the left peak of turbulent kinetic energy, the two-point spatial cross-correlation of swirling strength with velocity fluctuation and concentration fluctuation were calculated. All the correlation fields contain one positively correlated region and one negatively correlated region although the orientations of the correlation fields varied, due to the flow transitioning from wake, to jet, to channel flow. Finally, linear stochastic estimation was used to calculate conditional structures. The large-scale structures in the velocity field revealed by linear stochastic estimation are spindle-shaped with a titling stream-wise major axis.