气相爆轰波绕射流场显示研究

采用基于红宝石激光器（波长694.3 nm）的纹影系统,对气相爆轰波绕射进行了初步的流场显示研究。采用单色激光和合适半带宽（15 nm）的滤光片,有效地消除了爆轰波自发光对流场显示的影响。合理设置激光器同步控制系统的触发延时,得到了序列的爆轰波阵面纹影照片。结果表明:图像清晰地显示了爆轰波阵面的诱导激波、横波及化学反应区。当爆轰波在左尖点处绕射,受稀疏波作用,诱导激波与化学反应区明显分离,导致爆轰波衰减为爆燃。分离的诱导激波和折皱的化学反应区在纹影图上清晰可见。诱导激波在垂直支管右壁面反射,诱导二次起爆。畸变爆轰波在水平和垂直支管中均发生马赫反射。提高初压,爆轰波受分叉口几何属性的影响减小,畸变爆轰波在水平和垂直支管下游较易恢复为自持爆轰波。     

气相爆轰波在半圆形弯管中传播现象的实验研究

对气相(2H2/O2/Ar系统)爆轰波在半圆形弯管中的传播现象进行实验研究。用烟迹膜记录了弯管中爆轰波的胞格结构,采用压电传感器测量了沿弯管内外母线指定点的压力时间曲线,得到了爆轰波沿弯管内、外母线的平均速度和胞格尺寸的变化。结果表明:当平面爆轰波进入弯管后,受壁面的几何形状作用,诱导激波阵面发生弯曲。沿诱导激波阵面,自内母线到外母线方向,激波强度逐渐增大。同时,爆轰波后的化学反应区也受到影响,胞格尺寸发生较明显的变化。在本文条件下,当初压p08.00kPa,受扰动的爆轰波在弯管出口下游仍恢复为强度不变的稳定爆轰。胞格记录的三波点迹线表明:受扰动的爆轰波在出口段发生了马赫反射。实验结果还表明:当p0降至5.33kPa,平面稳定爆轰波经过半圆形弯管后,其强度发生衰减并直至出现熄灭。     

不同角度分叉管道内氢气-空气爆轰传播特性

在3种角度分叉管道内开展化学计量比氢气-空气爆轰实验,采用自制的火焰传感器和烟迹法分别获得了爆轰波传播速度和胞格结构,探究了不同角度管道分叉对爆轰传播的影响。结果表明:氢气-空气爆轰在经过分叉三通时受分叉口稀疏波影响导致爆轰波衰减解耦,但随着入射激波与下游管道壁面碰撞,逐渐由规则反射向马赫反射转变,最终完成重起爆过程。其中,直通支管内爆轰衰减主要受支管入口面积的影响,随着分叉角度增大,入口面积减小,爆轰衰减程度和重起爆距离也随之减小;而分叉支管内,爆轰衰减受支管入口面积与入口渐扩程度共同影响,但随着分叉角度的增大,入口面积变为主要影响因素。不同角度分叉管内的实验结果均表明,初始压力升高能显著提高爆轰稳定性,从而削弱分叉几何结构的影响。     

气相爆轰波反应区结构的平面激光诱导荧光测量

基于平面激光诱导荧光(PLIF)技术对2H2 O2 10Ar的预混气体爆轰波反应区结构进行实验研究.采用高浓度的氩稀释有利于减小爆轰化学反应自发辐射光对OH荧光的影响.合理设置PLIF系统、爆轰波和ICCD之间的同步控制触发延时,得到爆轰波阵面附近的OH荧光分布图像.结果表明:诱导激波后反应阵面不是平面且不稳定.荧光图像上能清晰地看到类似拱顶石的结构,它位于两马赫杆之间,以入射激波、剪切层和反应阵面为边界.无论是在马赫杆后还是在入射激波后,OH浓度分布在诱导区末端急剧增加至最大值.随着离开反应阵面的距离增加,OH浓度快速减小.由于爆轰模式和激光片光方向的影响,从PLIF图像上测得的横波间距值较离散,均小于胞格宽度.     

5.12汶川大地震诱发大型崩滑灾害动力特征初探

对乙炔氧气混合气体中爆轰波与激波的正面对撞现象的实验研究是以高速摄影获 取两波对撞的x-t纹影图,以烟迹板记录对撞中的爆轰胞格图案,并基于激波 理论和经典CJ爆轰理论求解了两波对撞的稳态解并探寻其规律. 研究发现透射波系包括一道激波和爆轰波, 以及紧随爆轰波后的稀疏波区,这一结果对应于一维理论分析中的CJ解. 透射波系基本不受 初始压强影响;初始温度也只成比例地改变流场整体速度,温度越高,速度越快;对波系起 实质影响作用的是入射激波强度,激波越强,则整个透射流场呈现偏向激波的趋势;理论分 析还指出,稀疏波区的出现不可避免,当激波强度趋于声波稀疏波区趋于消失,激波越强则 疏波区趋于扩大. 两波对撞存在一个有限的转变阶段,透射爆轰首先减缓,接着迅速迸发为 过驱爆轰,然后再逐渐平衡为CJ爆轰. 对于强不稳定的燃气,对撞后爆轰波在空间上的发展 极不均衡,一些区域发生火焰面与诱导激波的严重脱离,随后的火焰面失稳发展为诱导激波 区内的爆轰波,实验观察到了这种爆轰在烟迹板上留下的极为精细的迹线.     

爆轰波与激波对撞的实验研究

对乙炔氧气混合气体中爆轰波与激波的正面对撞现象的实验研究是以高速摄影获取两波对撞的x-t纹影图,以烟迹板记录对撞中的爆轰胞格图案,并基于激波理论和经典CJ爆轰理论求解了两波对撞的稳态解并探寻其规律. 研究发现透射波系包括一道激波和爆轰波,以及紧随爆轰波后的稀疏波区,这一结果对应于一维理论分析中的CJ解. 透射波系基本不受初始压强影响;初始温度也只成比例地改变流场整体速度,温度越高,速度越快;对波系起实质影响作用的是入射激波强度,激波越强,则整个透射流场呈现偏向激波的趋势;理论分析还指出,稀疏波区的出现不可避免,当激波强度趋于声波稀疏波区趋于消失,激波越强则疏波区趋于扩大. 两波对撞存在一个有限的转变阶段,透射爆轰首先减缓,接着迅速迸发为过驱爆轰,然后再逐渐平衡为CJ爆轰. 对于强不稳定的燃气,对撞后爆轰波在空间上的发展极不均衡,一些区域发生火焰面与诱导激波的严重脱离,随后的火焰面失稳发展为诱导激波区内的爆轰波,实验观察到了这种爆轰在烟迹板上留下的极为精细的迹线.      

扩张管内爆轰波临界传播特性的研究

假设重点火位置沿扩张管内扰动区的最后一道特征线，结合描述爆轰波绕射后重点火产生的特征量Ｍ／ｙｓ与沿胞格长度方向诱导激波与化学反应区分离时爆轰波阵面衰减的速度梯度△ＭＣＪ／Ｌｃ，本文得到了临界条件下扩张管内爆轰波维持传播而不熄灭的重点火准则。利用Ｗｈｉｔｈａｍ的激波线射理论，由重点火准则导出了任意扩张管角度下爆轰波胞格尺寸的计算公式。计算结果与实验结果相比，二者不仅趋势一致，而且量值也很接近。     

环形方管道中爆轰胞格的三维研究

通过实验和三维数值模拟研究了爆轰波在环形管道内的传播。实验采用烟迹板记录了爆轰波的胞格结构。数值模拟基于带化学反应的三维Euler方程,采用五阶精度的WENO格式捕捉激波,采用具有TVD性质的三阶Runge-Kutta法处理时间项,并结合并行技术,对爆轰波的传播进行了数值研究。结果表明,环形管道外壁为收敛壁面,由于其对流场的压缩效应,外壁面及附近的胞格较小,且较均匀。而内壁为发散壁面,其对流场起稀疏效应,内壁面及附近的胞格较大,且呈周期性变化。同时, 不同壁面的胞格结构均出现了拍波(slapping wave),其形状呈弯曲的折线。     

可燃气体中激波聚焦的点火特性

数值模拟了二维平面激波从抛物面上反射在可燃气体中聚焦的过程，研究了形 成爆轰波的点火特性. 对理想化学当量比氢气/空气混合气体，在初始压强20kPa的条件下， 马赫数2.6-2.8的激波聚焦能产生两个点火区：第1个点火区是反射激波会聚引起的，第 2个点火区是由入射激波在抛物面上发生马赫反射引起的. 这种条件下流场中会出现爆燃转 爆轰，起爆点分别分布在管道壁面、抛物反射面和第2点火区附近. 起爆机理分别为激波管 道壁面反射、点火诱导激波的抛物面反射和点火诱导的激波与第2点火区产生的爆燃波的相 互作用. 不同的点火和起爆过程导致了不同的流场波系结构，同时影响了爆轰波传播的波动 力学过程.     

气相爆轰波传播过程中的自点火效应

基于基元反应模型和单步反应模型,对直管道中H₂-air混合气体中爆轰波的传播过程进行了数值模拟,揭示了气相爆轰波传播过程中的自点火效应。利用数值模拟方法计算了不同爆轰模型的点火延迟时间,并得到了爆轰波三波点的传播过程以及所形成胞格结构的尺寸。结果表明,胞格宽度与点火延迟时间成正比;爆轰波诱导区内气体的点火延迟时间与三波点的运动周期基本一致。进一步对结果分析可知,爆轰波的自维持传播取决于点火延迟时间(表征化学反应的特征时间)和三波点的运动周期(表征流动的特征时间)的匹配;当二者相匹配时,经过前导激波压缩后形成的高温高压爆轰气体,在短时间内实现了自点火,同时释放出大量的能量推动了爆轰波的前进,即爆轰波的稳定自维持传播依靠其自点火机制。     

Diffraction and re-initiation of detonations behind a backward-facing step

Diffraction phenomena of gaseous detonation waves behind a backward-facing step in a tube are observed by using high-speed schlieren photography and soot-track records as well as by pressure measurements on the sidewall. Mixtures are stoichiometric oxyhydrogen and those diluted by argon at sub-atmospheric pressures. Three types of phenomena are observed, that is, continuous propagation of detonation, re-initiation after a temporal extinction of detonation and complete extinction of detonation. The continuous propagation means that the diffracted wave does not affect the main propagation although reflected shock waves from the bottom surface of the tube may affect it. The re-initiation occurs at a wall surface of the tube behind a reflected shock wave after the main detonation wave has been extinguished. Positions and conditions of the re-initiation are discussed. The complete extinction is defined as disappearance of detonation cells behind the step within a certain length of the tube. Cases exist where an ignition occurs after several reflections off the bottom and top surface of the tube.     

Behavior of detonation waves at low pressures

With respect to stability of gaseous detonations, unsteady behavior of galloping detonations and re-initiation process of hydrogen-oxygen mixtures are studied using a detonation tube of 14 m in length and 45 mm i.d. The arrival of the shock wave and the reaction front is detected individually by a double probe combining of a pressure and an ion probe. The experimental results show that there are two different types of the re-initiation mechanism. One is essentially the same as that of deflagration to detonation transition in the sense that a shock wave generated by flame acceleration causes a local explosion. From calculated values of ignition delay behind the shock wave decoupled from the reaction front, the other is found to be closely related with spontaneous ignition. In this case, the fundamental propagation mode shows a spinning detonation. Received 10 March 1997 / Accepted 8 June 1997     

Detonation diffraction in combustible high-speed flows

Detonation propagating in a T-shaped tube with quiescent and moving hydrogen/oxygen/argon mixtures is numerically examined based on the Euler equations with detailed finite-rate chemistry using the fifth-order weighted essentially non-oscillatory scheme. When diffracted in a quiescent combustible mixture, the detonation wave propagating from the bottom of the T-shaped tube is influenced by the corner rarefaction waves and decays into a non-reacting shock. Subsequently, the decoupled shock reflects irregularly from the top wall. Through several reflections back and forth between the top and bottom walls, a planar detonation is finally re-established. When the combustible mixture in the horizontal part flows from the left to the right, the detonation products ejected from the vertical tube will retard the flow, generating a compression flow upstream and a rarefaction flow downstream. The disturbed detonation on the left side is stronger than that on the right side. The final planar detonation in the upstream direction propagates faster than the Chapman–Jouguet (CJ) detonation with compressed, fine cellular structures, whereas the detonation in the downstream direction propagates more slowly than the CJ detonation with elongated, coarse cellular structures. The details of the transient behavior of diffracting detonation in high-speed flows are discussed.     

Experimental investigation into the detonation characteristics of hybrid RDX–ethylene–air mixtures

An experimental study is conducted to determine the detonation characteristics of 1,3,5-trinitroperhydro-1,3,5-triazine (RDX) particles dispersed in a gaseous fuel air mixture in a vertical detonation tube with an inner diameter of 200 mm and a height of 5400 mm. Experiments are performed in both ethylene–air mixtures and RDX–ethylene–air hybrid mixtures. The detonation front pressure and velocity are measured with six pressure transducers along the detonation tube. The results show that the addition of RDX assists 4.0 vol.% ethylene–air mixtures in achieving detonation. The detonation front pressure increases noticeably with dust concentration up to \(474\hbox { g/m}^{3}\) in the RDX–ethylene–air hybrid mixtures, but the velocity only increases slightly. The cellular structures of RDX–ethylene–air hybrid mixtures and ethylene–air mixtures were obtained with the use of smoked foils and exhibit irregular structures. It is found that the measured cell size has a U-shaped curve with respect to RDX concentration.     

Re-initiation phenomenon of gaseous detonation induced by shock reflection

The two-dimensional, time-dependent, reactive Navier–Stokes equations including the effects of viscosity, thermal conduction and molecular diffusion were solved to reveal the wave evolution and chemical dynamics involved in the re-initiation process. The computation was performed for hydrogen–oxygen–argon mixtures at the low initial pressure (8.00 kPa), using detailed chemical reaction model. The results show that, the decoupled leading shock reflects on the right wall of the vertical branch. High temperature and pressure behind the reflected shock induce the generation of hot spots and local explosion. Therefore, the re-initiation of gaseous detonation occurs. In the re-initiation area, there exist very high OH concentration and no H ₂ concentration. However, in front of reflected shock, there exist relatively high H ₂ concentration and no OH radicals. Additionally, the shock–flame interaction induces RM instability. This results in the fast mixing between hot reacted gas mixture and the relatively cold unreacted gas mixture and accelerates the chemical reactions. However, the shock–flame interaction contributes much less to the re-initiation, in contrast with shock reflection. The transition of leading shock from regular reflection to Mach reflection happens during the re-initiation. The computed evolution of wave structures involved in the re-initiation is qualitatively agreeable with that from the experimental schlieren images.      

超音速来流中爆轰波衍射和二次起爆过程研究

预爆管技术被广泛地应用在爆轰波发动机的起爆过程中，但是在超音速来流中基于预爆管技术起始爆轰波的研究并未被广泛地开展。基于此，本文中数值研究了横向超音速来流对半自由空间内爆轰波的衍射和自发二次起爆、及管道内的衍射和壁面反射二次起爆两种现象的影响。数值模拟的控制方程为二维欧拉方程，空间上使用五阶WENO格式进行数值离散，采用带有诱导步的两步链分支化学反应模型。所模拟的爆轰波具有规则的胞格结构，对应于用惰性气体高度稀释过的可爆混合物中形成的爆轰波。结果表明:在半自由空间内，在本文所模拟的几何尺寸下，爆轰波并未成功发生二次起爆现象，但是爆轰波的自持传播距离随着横向超音速来流强度的增强而增加。在核心的三角形流动区域外，波面诱导产生了更多的横波结构；在管道内，横向的超音速来流在逆流侧对出口气流产生了压缩作用，能有效提高波面压力，因此反射后的激波压力也比较高。在同样的几何尺寸下，爆轰波在静止和超音速(Ma=2.0)气流中分别出现了二次起爆失败和成功两种现象，这是由于在超音速来流中化学反应面的褶皱诱导产生了横波结构，横波与管壁以及其他横波之间的碰撞提高了前导激波的强度，并最终促进了爆轰波在超声速流主管道内的成功起始。     

气相爆轰波在障碍物上Mach反射的实验验证

本文公布了气相爆轰波沿收缩管道传播时发生Mach反射的实验证据。在爆轰波通过的管道中安装不同楔角的楔块,形成管道的收缩。爆轰波在通过楔块时会发生Mach反射。利用烟熏玻璃片记录到了爆轰波Mach反射时形成的三波点迹线及其两侧胞格尺寸和密度的变化。据我们掌握的资料,这是首次用胞格结构变化的记录证实,气相爆轰波与无化学反应的空气中的冲击波一样,在一定的入射条件下会发生Mach反射。这一实验结果可使我们更深入了解爆轰波的本质,也为数值模拟气相爆轰波在障碍物上Mach反射现象提供了可对比的依据。     

Detonation driver for enhancing shock tube performance

The development of a shock-induced detonation driver for enhancing the performance of a shock tube is described. The detonation wave is induced by the expansion of helium or air. Various gaseous fuel-oxidizer combinations are examined. This method produces a detonation wave which propagates downstream that transitions into a shock wave in the driven section. High-enthalpy flows with a maximum total temperature of 4200 K and a maximum total pressure of 34 atm in the driven tube are achieved. The problems of achieving the so-called perfectly-driven mode as well as those of inadequate fuel-oxidizer mixing are discussed.Received: 26 April 2002, Accepted: 23 December 2002, Published online: 28 April 2003     

爆轰驱动高焓激波膨胀管性能研究

介绍了中国科学院高温气体动力学实验室JF-16爆轰驱动高焓激波膨胀管的研制进展及其性能测试结果. 性能研究主要测量了入射激波速度和压力曲线. 根据入射激波速度,应用Mirels的黏性激波管理论计算了超高速试验气流的运动速度,然后应用Gaseq软件计算了试验气流的热力学参数. 研究结果表明:在16.35\,m长的JF-16激波膨胀管中获得了流速7\,000\,m/s以上的稳定试验气流,试验时间为50$\sim$100$\mu$s, 试验气流总焓30\,MJ/kg左右.