动态扩展裂纹的若干反平面问题的研究

采用复变函数论，对反平面条件下的动态裂纹扩展问题进行研究。通过自相似函数的方法可以获得解析解的一般表达式。应用该法可以很容易地将所讨论的问题转化为Riemann—Hilbert问题，并可以相当简单地得到问题的闭合解。文中分别对裂纹面受均布载荷、坐标原点受集中增加载荷、坐标原点受瞬时冲击载荷以及裂纹面受运动集中载荷Px／t作用下的动态裂纹扩展问题进行求解，得到了裂纹扩展位移、裂纹尖端的应力和动态应力强度因子的解析解。应用该解并通过叠加原理，就可以求得任意复杂问题的解。     

冲击载荷下扩展裂纹尖端动态能量释放率分布的焦散线分析

借助高速摄影捕捉裂纹瞬态扩展过程，利用动态焦散线研究了含有裂纹的三点弯曲梁在冲击载荷作用下扩展裂纹尖端的动态能量释放率分布规律；综合分析了裂纹扩展时间、长度、速度，以及扩展裂纹尖端动态应力强度因子与它的变化关系，表明了动态能量释放率在裂纹扩展过程中的驱动作用。     

动载荷作用下微裂纹的增韧分析

在实验研究的基础上，将细观统计力学应用于材料的动态增韧分析中，探索性的研究了在动态载荷作用下微裂纹的增韧机理，并进行了相应的有限元分析计算，得出在动载荷作用下，微裂纹增韧主要表现在微裂纹的快速成核。如果要提高材料在动态情况下的增韧幅值，必须提高增韧颗粒的特征尺寸。     

双轴压缩载荷下裂纹动态传播的实验研究

本文研究了双轴压缩载荷下裂纹的起裂和非共面传播问题，用动态光弹性方法成功地记录下裂纹的动态扩展过程。获得了双轴压缩载荷下扩展裂纹的传播速度，临界开裂载荷以及开裂角第一系重要断裂参数。研究表明，在双轴压缩载荷下不闭合裂纹前缘应力场是一个混合型的奇异场，裂纹的扩展过程为稳态过程并且表现出显著的阶段性特点。     

爆炸载荷下板条边界斜裂纹的动态扩展行为

为了研究爆炸应力波作用下板条边界斜裂纹的动态扩展行为,首先分析了爆炸应力波在含边界斜裂纹板条中的传播,其次采用动态焦散线实验方法,进行了爆炸载荷下板条边界斜裂纹扩展规律的实验研究.研究结果表明,爆炸应力波作用下,板条试件边界斜裂纹的扩展过程中,裂纹扩展速度、扩展加速度和裂尖动态应力强度因子随时间波动变化,扩展速度最大值...     

塑性动态断裂实验研究

本文利用自制的实验装置,对韧性材料在爆炸冲击载荷作用下的塑性动态断裂特性,进行了实验研究,其中包括高塑性应变速率下,塑性区裂纹扩展过程和扩展速度的测试;塑性动态断裂韧性CTOD,及其在不同裂纹扩展速度下变化规律的测试。同时,对不同裂纹扩展速度的试件断口进行微观分析。     

界面超高速自相似动态分层分析：反平面情况

对材料界面超高速自相似动态分层的反平面问题进行了解析分析。分层模拟为界面裂纹由零长度自相似扩展，扩展速度为蹭音速或超音速。首先考虑运动集中载荷作用下界面动态分层的情况，利用界面裂纹自相似扩展的运动位错模型将问题归结为奇异积分方程，并求得解析解，分析了裂纹尖端的应力奇性，获得了动应力强度因子。最后，利用叠加原理给出了ｘ＾ｎ型载荷作用下界面动态分层的解。     

致密砂岩巷道模型试件动态起裂及止裂全过程分析

为了开展在不同冲击载荷作用下巷道围岩内裂纹的起裂、扩展及止裂等问题，以可调速冲击试验机进行动态加载试验，采用致密青砂岩制作裂纹巷道模型试件，并利用裂纹扩展计分别记录了动态起裂、扩展、止裂等时刻，对裂纹扩展速度的变化规律进行分析；随后采用AUTODYN有限差分法软件进行相应的数值模拟，数值模拟得到的裂纹扩展路径与试验结果基本一致。经过两者对比分析可知:随着冲击载荷作用的增加，裂纹平均扩展速度逐渐增大，随后趋于稳定值；预制裂纹的起裂时间随着冲击速度载荷的增加而逐渐降低，并在稳定值上下波动；随着冲击速度载荷的增加，裂纹扩展路径过程中的止裂时段逐渐变短。     

爆炸载荷下裂纹扩展方向预测的研究

借助动态焦散线方法测试结果,对裂纹尖端初始曲线范围内的第二应力张量不变量分布进行了分析,并通过Det.(iσj)准则对爆炸载荷下裂纹扩展的方向及临界条件进行预测。结果表明,爆炸应力波作用下,裂纹尖端初始曲线范围内第二应力张量不变量最大值与裂纹尖端动态应力强度因子有相同的变化规律,完全可以反映裂纹尖端的动态行为。Det.(iσj)准则用于分析爆炸应力波作用下缺陷介质裂纹扩展行为是十分有效的,特别是对于裂纹起始扩展方向及扩展临界条件有准确的描述。     

岩石巴西圆盘动态劈裂的流形元法模拟

利用二阶流形元法,通过引入裂纹产生与扩展判据,对冲击载荷作用下岩石平台巴西圆盘的动态拉伸劈裂过程进行了数值模拟,再现拉伸波作用下圆盘被劈裂的过程。模拟现象与实验结果相符,动态平衡时的应力分布与有限元结果基本一致。从而验证了流形元在模拟冲击载荷作用下材料动态破坏过程的有效性和可行性。     

Transient response of a cracked piezoelectric strip under arbitrary electro-mechanical impact

By using the well-developed integral transform methodology, the dynamic response of stress and electric displacement around a finite crack in an infinite piezoelectric strip are investigated under arbitrary dynamic anti-plane loads. The dynamic stress intensity factors and electric displacement are obtained analytically. It is shown that the dynamic crack-tip stress and electric field still have a square-root singularity. Numerical computations for the dynamic stress intensity factor show that the electric load has a significant influence on the dynamic response of stress field. The higher the ratio of the crack length to the width of the strip, the higher the peak value of the dynamic stress intensity factor is. On the other hand, the dynamic response of the electric field is determined solely by the applied electric load. The electric field will promote or retard the propagation of the crack depending on the time elapse since the application of the external electro-mechanical loads. The project supported by the National Natural Science Foundation of China and the Post-Doctor Science Foundation of China     

Oblique edge crack in an anisotropic material under antiplane shear

An oblique edge crack in an anisotropic material under antiplane shear loadings is investigated. The antiplane problems are formulated based on a linear transformation method. An anisotropic solid containing an edge crack subjected to concentrated forces is first considered. The stress intensity factor for the edge crack with concentrated forces is obtained from the solution of the transformed edge crack in an isotropic material which is solved by using conformal mapping technique and complex function theory. The solution of the edge crack under concentrated loads is used to construct the stress intensity factor for the oblique edge crack in the anisotropic material subjected to antiplane distributed loads. Some numerical computations are carried out to calculate the stress intensity factors for the edge crack in inclined orthotropic materials subjected to point forces as well as distributed tractions.     

Stress intensity factors of an oblique edge crack subjected to normal and shear tractions

Stress intensity factors (SIFs) were obtained for an oblique crack under normal and shear traction and remote extension loads. The oblique crack was modeled as the pseudodislocation. The stress field due to tractions was solved by the Flamant solution. The SIR of Mode I and Mode II (K_Iand K_II) were then obtained. Finite element analysis was performed with ABAQUS and compared with the analytical solutions. The analytical solutions were in good agreement with the results of FEM. From investigating SIFs and their ranges, the following results were obtained. The growth rate of an oblique edge crack decreased due to the reduction in the SIF ranges. The crack driving force depended on the obliquity, the normal traction and the ratio of crack to traction length. The peak value of shear traction was found as a key parameter to accelerate the crack growth.     

Dynamic response of a cracked piezoelectric ceramic under arbitrary electro-mechanical impact

The dynamic response of a cracked piezoelectric ceramic under in-plane electric and anti-plane mechanical impact is investigated by the integral transform method. The electric and mechanical loads are assumed to be arbitrary functions of time. It is shown that the dynamic crack-tip stress and electric displacement fields still have a square-root singularity. Numerical computations for the dynamic stress intensity factor show that the electric load has a significant influence on the dynamic response of stress field. On the other hand, the dynamic response of the electric field is determined solely by the applied electric field. The electric field will promote or retard the propagation of the crack depending on the time elapsed since the application of the external electro-mechanical loads.     

界面裂纹尖端的动态奇异特性

本文研究了界面裂纹尖端的动态应力场的奇异特性.引入尖端无摩擦接触的界面裂纹模型并采用具有运动边界的控制积分方程.证明了在动态界面裂纹尖端仅存在平方根奇异的应力场.数值结果表明接触区中的正应力确保持为压应力.为表现界面裂纹的动态特性,给出了应力强度因子和裂纹面接触区尺寸的数值结果.     

压应力场中爆生裂纹分布与扩展特征实验分析

采用动静组合加载实验装置和数字激光焦散线实验系统,进行了0、3、6、9 MPa等4种压应力场中PMMA试件的爆破致裂实验,分析了沿静态主应力方向扩展的裂纹运动学和力学行为。实验结果表明:首先,静态竖向载荷在预制炮孔周围产生应力集中,在炮孔壁上下端部处出现最大拉应力;随后,在动态爆炸载荷的叠加作用下,裂纹优先在炮孔壁上最大拉应力位置处起裂,并沿最大主应力方向扩展;裂纹扩展过程中,静态竖向载荷越大,裂纹扩展速度越大,且裂纹尖端应力强度因子值越大。     

I-II复合型裂缝断裂角的分层剪滞模型与分析

采用修正的剪滞理论建立了岩石、混凝土等准脆性材料的I-II复合型裂缝在单向拉伸荷载作用下的计算模型,得到了与实验相吻合且优于传统S判据的断裂角。通过对远场应力、斜裂缝区应力以及子层位移的合理简化,得到了求解剪滞分析模型的边界条件,进而得到了含斜裂缝的各子层位移分布函数。引入最大应力集中因子,对I-II复合型裂缝前缘应力场进行简化;基于斜裂缝沿最大应力集中因子方向扩展,得到裂缝的断裂角。根据斜裂缝的应力分布,设置不同的子层分区,得到了更为细化的位移分布模式。通过对计算数据的分析,针对单向拉伸荷载作用下的I-II复合型裂缝,建立了按应力场分区设置子层的分层剪滞模型,得到更为精确的斜裂缝断裂角。     

冲击载荷作用下圆孔缺陷对裂纹动态扩展行为的影响规律

空腔和裂纹缺陷通常共存于深部地下岩体中,它们共同影响着岩体的结构安全性与稳定性。为了探究动力扰动载荷下圆形空腔对裂隙岩体内裂纹扩展行为的影响规律,提出了不同圆孔倾角的直裂纹空腔圆弧开口试件（circular opening specimen with straight crack cavity, COSSCC）,利用自制大型落锤冲击实验装置进行动态加载实验,同时采用裂纹扩展计系统测试了裂纹的动态起裂时刻与裂纹扩展速度等各种断裂力学参数,随后采用有限差分软件Autodyn进行裂纹扩展路径与圆孔周围应力场的数值分析,并采用有限元软件Abaqus计算裂纹的动态起裂韧度与裂纹扩展过程中的动态扩展韧度。结果表明:（1）当圆孔倾角θ小于10°时,裂纹扩展路径会偏折并穿过圆孔表面;当圆孔倾角θ为20°与30°时,裂纹扩展路径向圆孔方向发生偏折但不会穿过圆孔,圆孔具有明显的裂纹扩展引导作用; 当圆孔倾角θ为40°与50°时,裂纹扩展路径不会发生偏折,圆孔引导作用明显减弱。（2）当裂纹扩展路径达到圆孔空腔附近时,裂纹尖端的拉伸应力区与圆孔边缘的拉伸应力区发生重合,此时裂纹扩展速度显著增大,裂纹动态断裂韧度显著减小。（3）裂纹的偏折方向与裂纹尖端最大周向应力的方向基本一致。（4）裂纹动态断裂韧度始终小于裂纹起裂韧度,且裂纹动态断裂韧度与裂纹动态扩展速度呈负相关关系。裂纹动态扩展速度越大,裂纹动态断裂韧度越小。     

Transient response of a piezoelectric ceramic with two coplanar cracks under electromechanical impact

The transient response of two coplanar cracks in a piezoelectric ceramic under antiplane mechanical and inplane electric impacting loads is investigated in the present paper. Laplace and Fourier transforms are used to reduce the mixed boundary value problems to Cauchy-type singular integral equations in Laplace transform domain, which are solved numerically. The dynamic stress and electric displacement factors are obtained as the functions of time and geometry parameters. The present study shows that the presence of the dynamic electric field will impede or enhance the propagation of the crack in piezoelectric ceramics at different stages of the dynamic electromechanical load. Moreover, the electromechanical response is greatly affected by the ratio of the space of the cracks and the crack length.