土体动力"广义阻尼比退化系数"本构模型

针对土动力试验中土体反向卸载(或加载)曲线形状有时表现为先变化平缓后变化剧烈这一特征,基于原来的"阻尼比退化系数"本构模型和土体实验结果G/Gmax-γ和λ-γ曲线,给出了不规则荷载作用下曲线形状可调的"广义阻尼比退化系数"本构模型,并阐述了第二种"阻尼比退化系数"模型、"广义阻尼比退化系数"模型的函数表达武及实现过程.通过对试验阻尼比的模拟表明,所建立的加卸载准则尤其能准确拟合试验阻尼值,是对广义Masing准则的一种简化及实用化.由于调制因子Ad的可变性,它较原模型有更强地模拟试验本构曲线形状的能力.针对台湾LotungDHB钻井台阵试验场地,"阻尼比退化系数"模型和"广义阻尼比退化系数"模型分别进行了非线性地震反应分析,并将结果与强震观测记录进行比较,结果表明:"广义阻尼比退化系数"模型计算的复合加速度地震动的蜂值大小、波形大小相对关系及后续波形,与实际地震记录较相一致,说明了模型的合理性以及实际工程应用的可行性.     

非连续变形计算力学模型的粘弹性分析方法Ⅰ:基本理论

基于粘弹性广义有限单元和接触力元，发展了适用于多体相互作用系统非连续变形分析的粘弹性数值分析方法，通过虚功原理，给出了其分区参变量最小势能原理，从而阐明了其理论基础。粘弹性广义有限单元的本构关系可由粘弹性退化为弹性或刚性，因此本文所提出的方法可对由刚体、弹性体和粘弹性体所构成的复杂多体系统在外荷载作用下的力学行为进行数值模拟，同时能够比本文精确地直接得到多体之间的接触应力。     

土体的本构模型和超重力物理模拟

数值模拟和物理模拟是分析土体沉降和稳定性的主要手段. 本构模型作为描述土体应力应变关系的数学表达式, 是数值模拟的基础. 土体具有碎散性, 这一基本物理特性导致了其具有压硬性、摩擦性和剪胀性, 这是土的力学特性区别于金属的主要特征, 在土体的本构模型中必须反映这3个基本特性. 传统土力学将土体的变形和强度分离考虑, 分别采用弹性理论和基于刚塑性模型的极限平衡理论分析, 虽然应用广泛, 但由于不能全面地反映土的基本力学特性, 计算结果的精度常常难以满足定量分析的需要. 剑桥模型作为第一个全面反映压硬性、摩擦性和剪胀性的弹塑性本构模型, 实现了变形和强度的统一, 能较好地描述饱和正常固结黏土的应力应变关系, 被视为是现代土力学的开端; 统一硬化模型通过引入一个独特的硬化参数进一步发展了剑桥模型, 将适用范围扩大到超固结黏土. 作者认为, 未来岩土体本构模型研究的挑战是: 如何考虑岩土体在受力过程中土骨架相变与多场耦合, 以解决目前本构模型尚无法定量分析的能源、交通、环境和水利相关的重大岩土工程问题. 超重力物理模拟具有缩尺效应和缩时效应, 克服了常重力物理模拟中模型的应力水平低于原型的缺点, 特别适用于大尺度、长历时问题的模拟. 相较数值模拟, 超重力物理模拟的优势在于能够检验本构模型的合理性, 揭示本构模型无法描述的未知特性. 最后, 介绍了采用数值模拟和物理模拟联合分析大直径钢管桩水平受荷特性的工程案例.      

CONSTITUTIVE MODELS AND HYPERGRAVITY PHYSICAL SIMULATION OF SOILS$^{\bf 1)}$

数值模拟和物理模拟是分析土体沉降和稳定性的主要手段. 本构模型作为描述土体应力应变关系的数学表达式, 是数值模拟的基础. 土体具有碎散性, 这一基本物理特性导致了其具有压硬性、摩擦性和剪胀性, 这是土的力学特性区别于金属的主要特征, 在土体的本构模型中必须反映这3个基本特性. 传统土力学将土体的变形和强度分离考虑, 分别采用弹性理论和基于刚塑性模型的极限平衡理论分析, 虽然应用广泛, 但由于不能全面地反映土的基本力学特性, 计算结果的精度常常难以满足定量分析的需要. 剑桥模型作为第一个全面反映压硬性、摩擦性和剪胀性的弹塑性本构模型, 实现了变形和强度的统一, 能较好地描述饱和正常固结黏土的应力应变关系, 被视为是现代土力学的开端; 统一硬化模型通过引入一个独特的硬化参数进一步发展了剑桥模型, 将适用范围扩大到超固结黏土. 作者认为, 未来岩土体本构模型研究的挑战是: 如何考虑岩土体在受力过程中土骨架相变与多场耦合, 以解决目前本构模型尚无法定量分析的能源、交通、环境和水利相关的重大岩土工程问题. 超重力物理模拟具有缩尺效应和缩时效应, 克服了常重力物理模拟中模型的应力水平低于原型的缺点, 特别适用于大尺度、长历时问题的模拟. 相较数值模拟, 超重力物理模拟的优势在于能够检验本构模型的合理性, 揭示本构模型无法描述的未知特性. 最后, 介绍了采用数值模拟和物理模拟联合分析大直径钢管桩水平受荷特性的工程案例.     

超固结饱和黏性土的弹塑性本构模型及三轴试验模拟

针对饱和超固结黏性土现有的下加载面修正剑桥模型破坏应力比为定值,不能反映土体在不同应力状态下强度特性存在差异这一问题,为了更好地反映应力状态变化对破坏应力比的影响,基于三剪统一强度准则确定超固结土的破坏应力比。在此基础上得到了超固结土的弹塑性本构模型,该模型的特点是能够描述土体受力时的中间主应力效应、应力区间效应、拉压差影响。基于该本构模型作了常规三轴压缩条件下超固结饱和黏性土的模拟结果与试验结果对比,结果表明:该模型能够反映不同超固结比下土的变形、剪胀、孔隙水压力变化特性和规律。利用该本构模型模拟了排水和不排水条件下的真三轴压缩试验,得到了相应的应力-应变特性曲线。     

土与结构界面接触问题研究进展评述

针对土与结构相互作用研究中的土-结构界面接触问题, 本文从界面接触力学特性及界面接触模拟两个方面的研究展开评述. 分析了接触面(带)的力学特性和变形分布规律方面的试验方法和取得的成果, 讨论了现有试验方法的不足;随后, 对土-结构界面接触行为的两类模拟方法--接触面单元方法和接触力学方法进行了讨论;最后提出了今后工作的重点.     

线弹性广义界面层模型的研究

为了用界面层方法分析一般结构中的裂纹扩展问题,提出了广义界面层的概念.基于能量释放率G相等的原则,对界面层的本构关系进行了线弹性等效.在此基础上,重点推导了含Ⅰ型裂纹双悬梁(DCB)的载荷-位移函数,并借助Abaqus软件对双悬梁的分层问题进行数值模拟.理论推导和数值模拟的结果证明了广义界面层的线弹性等效是可行的.     

结构与土接触面的弹黏塑性本构模型

基于Goodman接触面单元,在Clough--Duncan双曲线关系式的基础上改进了三元件宾厄姆体,建立了结构与土接触面的弹黏塑本构模型,使用ABAQUS的FRIC子程序对该模型进行了二次开发.通过改装的应力控制式结构-土接触面剪切试验仪进行了接触面长期剪切试验,验证了该接触面本构模型.研究结果表明:结构与土接触面的弹黏塑本构模型能较好地模拟接触面的力学特性和时间效应;正应力对结构与土接触面的力学行为影响较大,正应力越大,接触面的时间效应越显著.     

土结构性本构模型研究现状综述

土本构模型的建立是一个重要而又复杂的问题,到目前为止,国内外学者们已提出数以百计的土本构模型,诸多文献也对这些模型进行了评述和归纳。然而这些土本构模型多是在扰动土或砂土的基础上发展和建立起来的,它们难以描述由于土结构性引起的各种非线性行为,其计算结果与实际情况相差甚远。天然土体一般都具有一定的结构性,所以有必要建立考虑土结构性影响的土本构模型。针对这个现实,目前有些学者已基于各种理论和方法,提出了一些可以考虑土结构性影响的土本构模型,并得了较好的应用。但在目前的文献中还很少有对土的结构性本构模型研究进行归纳,基于此,本文简要介绍了一下目前土的结构性本构模型研究现状,并提出了这些本构模型在应用中所存在的问题。     

跨断层埋地管线-土接触非连续变形分析

跨断层埋地管线系统主要由管线及其周围土体两种不同介质组成,具有分析介质不连续性特性.为实现对管-土接触介质的不连续性分析,采用非连续变形分析与有限元分析相结合的方法,将跨逆断层埋地管线系统从实际工作状态中取出一部分作为分析对象.利用有限元分析方法对管线及其周围土体进行网格划分;而管-土之间的相互作用,利用非连续变形分析中的不连续介质接触处理方法实现模拟.通过模型的数值分析,研究了逆断层作用下管-土之间的非连续变形相互作用状态,验证了利用非连续变形分析与有限元方法相结合解决埋地管线-土接触的可行性和有效性,为管-土相互作用分析提供了新的研究思路和研究方法.     

Constitutive modeling of soil-structure interface through the concept of critical state soil mechanics

The behavior of soil-structure interface can be crucial to the overall response of a soil-structure system. The numerical simulation of soil-structure interaction problem requires proper modeling of the interface. The similarity between the behavior of soil and interface is first analyzed in the present paper. With this similarity, the concept of critical state soil mechanics (CSSM), which has been successfully used in the modeling of soil behavior, is used to develop a constitutive model for soil-structure interface in the framework of generalized plasticity. The model is capable of modeling strain hardening, softening, normal dilatancy and stress-path dependency of interface between sandy soil and structures during shearing. The effects of normal pressure as well as density of sand are captured in the model. The performance of the model is verified with various experimental results. The unified modeling of the behavior of interfaces with different roughness, different density of soil and different normal pressures using the concept of CSSM is also successfully attempted.     

DYNAMIC RESPONSE OF UNDERGROUND STRUCTURES BY TIME DOMAIN SBEM AND SFEM

The dynamic interaction problems of three-dimensional linear elastic structures witharbitrary shaped section embedded in a homogeneous,isotropic and linear elastic half spaceunder dynamic disturbances are numerically solved.The numerical method employed is acombination of the time domain semi-analytical boundary element method(SBEM)usedfor the semi-infinite soil medium and the semi-analytical finite element method(SFEM)used for the three-dimensional structure.The two methods are combined throughequilibrium and compatibility conditions at the soil-structure interface.Displacements,velocities,accelerations and interaction forces at the interface between undergroundstructure and soil medium produced by the diffraction of wave by an underground structurefor every time step are obtained.In dynamic soil-structure interaction problems,it isadvantageous to combine the SBEM and the SFEM in an effort to produce an optimumnumerical hybrid scheme which is characterized by the main advantages of the two methods.The     

准静态离散元方法和线性粘弹性问题的模拟

离散元方法是近年发展起来的一种新数值方法,但原则上只能用于动态问题。从静力平衡条件出发建立了离散元系统的准静态演化方程并证明了系数矩阵具有对称正定、稀疏、带状分布等特点,适用于“有效列”方法求解,该解法比高斯消去法节省更多的内存和机时。通过引入广义Maxwell体的元间作用模型建立起线性粘弹性材料准静态响应的离散元模拟方法。该方法独立于传统动态离散元方法,是传统动态离散元方法的拓展,可望在更多领域获得应用。     

土—结构相互作用对高柔结构风振响应TMD控制的影响

文中研究了土－结构相互作用对高层,高耸结构风振响应TMD控制的影响,讨论了结构不同基础类型和不同地在土介质对TMD风振控制效率的影响,数值结构表明,土－结构相互作用对风振响应TMD控制的影响不同于对地震响应TMD控制的影响。     

无单元法（EFGM）——在岩土工程上有限元法的有力补充

作为一种新的岩土工程数值计算方法，无网格伽辽金法具有局部化技术的无单元特性。该法与传统FEM相比，在精度和后处理等方面有着明显的计算优势。本文全面介绍了EFGM，并结合岩土工程领域中的土体固结变形问题，推导了EFGM的一维、二维固结问题的离散方程；同时对算例进行计算，将其结果与精确解和传统FEM解进行比较后，得出结论：精度是较高的，处理边界是准确的。尤其当与FEM联合使用时，既能发挥FEM的经验优质，又能体现EFGM的无网格特点，计算效果十分显著，因此，EFGM是FEM的有力补充。     

移动接触下求解二维闭合裂纹的双重迭代边界元法

使用子域边界元法对受移动接触弹性体作用下的二维闭合裂纹问题进行了数值计算。由于两弹性体的接触界面和裂纹表面的接触范围的大小和接触状态事先是未知的 ,对此 ,在两个接触表面同时采用迭代的方法进行了求解。在裂纹的每个裂尖上都采用了四分之一的奇异单元以保证裂尖位移场和应力场奇异性的满足。用我们编制的二维裂纹问题程序对一些中心裂纹问题进行了计算 ,计算结果与经典断裂力学的理论值比较吻合。在无摩擦的条件下 ,对一些具有不同角度且受移动接触弹性体作用下的闭合裂纹问题进行了数值计算 ,得到了一些耦合作用下的应力强度因子的计算结果     

Modeling interface shear behavior of granular materials using micro-polar continuum approach

Recently, the authors have focused on the shear behavior of interface between granular soil body and very rough surface of moving bounding structure. For this purpose, they have used finite element method and a micro-polar elasto-plastic continuum model. They have shown that the boundary conditions assumed along the interface have strong influences on the soil behavior. While in the previous studies, only very rough bounding interfaces have been taken into account, the present investigation focuses on the rough, medium rough and relatively smooth interfaces. In this regard, plane monotonic shearing of an infinite extended narrow granular soil layer is simulated under constant vertical pressure and free dilatancy. The soil layer is located between two parallel rigid boundaries of different surface roughness values. Particular attention is paid to the effect of surface roughness of top and bottom boundaries on the shear behavior of granular soil layer. It is shown that the interaction between roughness of bounding structure surface and the rotation resistance of bounding grains can be modeled in a reasonable manner through considered Cosserat boundary conditions. The influence of surface roughness is investigated on the soil shear strength mobilized along the interface as well as on the location and evolution of shear localization formed within the layer. The obtained numerical results have been qualitatively compared with experimental observations as well as DEM simulations, and acceptable agreement is shown.     

A multi-fiber approach for modeling corroded reinforced concrete structures

Taking into account the specific behavior of the steel/concrete interface is of primary importance to predict properly the structural response of RC structures. Several constitutive models have been proposed in the literature within the framework of nonlinear finite element method (2D and 3D). Such approaches usually lead to high computational costs due to the large number of degrees of freedom. In the present paper, a multifiber-based model including the steel/concrete interface behavior is proposed. Despite the fact that the kinematics of the multi-fiber approach is based on the theory of beams, this simplified strategy accounts for local phenomena such as the relative sliding between concrete and steel. Furthermore, this steel/concrete interface constitutive model can be extended to model the loss of bond properties due to corrosion. The numerical implementation aspects are described and local responses at the Gauss point level are exposed in the cases of monotonic loadings with and without corrosion. The efficiency and the reliability of the proposed approach are tested on structural case studies which highlight a good agreement between numerical and experimental results. This multifiber-based model provides a pertinent tool for the engineers concerns with the structural assessment of degraded reinforced concrete structures.     

Critical state shear behavior of the soil-structure interface determined by discrete element modeling

The interface between soil and structure can be referred to as a soil-structure system, and its behavior plays an important role in many geotechnical engineering practices. In this study, results are presented from a series of monotonic direct shear tests performed on a sand-structure interface under constant normal stiffness using the discrete element method (DEM). Strain localization and dilatancy behavior of the interface is carefully examined at both macroscopic and microscopic scales. The effects of soil initial relative density and normal stress on the interface shear behavior are also investigated. The results show that a shear band progressively develops along the structural surface as shear displacement increases. At large shear displacement a unique relationship between stress ratio and void ratio is reached in the shear band for a certain normal stress, indicating that a critical state exists in the shear band. It is also found that the thickness and void ratio of the shear band at the critical state decreases with increasing normal stress. Comparison of the DEM simulation results with experimental results provides insight into the shear behavior of a sand-structure interface and offers a means for quantitative modeling of such interfaces based on the critical state soil mechanics.     

桩-土接触效应及对桥梁结构地震反应的影响

目前有关涉及桥梁桩基础地震反应的研究大多是基于桩与桩侧土体之间无相对滑动、位移保持协调的假定。本文针对地震作用下桥梁桩基础的接触面效应及其对结构地震反应的影响问题，以某桥梁工程为背景，通过在桩-土交界面处设置接触单元来模拟桩-土间的接触非线性，建立了土-桩-桥梁结构相互作用体系的三维分析模型。利用这一模型，分析了地震作用下桩-土交界面处的动力反应形态，探讨了桩-土间的接触非线性及其对桥梁结构地震反应的影响。初步分析结果表明：在强震作用下，桩-土间会产生较强的接触非线性，在本文模型中，这种非线性主要表现为桩-土交界面处的滑移；考虑桩-土间的接触面效应将使结构的位移反应结果较基于桩-土间位移协调的情形有所增大。