脊状表面减阻特性的风洞试验研究

利用热线风速仪，对光滑表面和多个脊状表面在低速风洞中进行了表面流场测试。基于测得的边界层速度分布数据，利用对数律区速度分布公式，编程分别计算出光滑表面和脊状表面的壁面摩擦速度和虚拟原点。研究发现，脊状表面最大减阻量达13．5％；有减阻效果的脊状表面使边界层速度曲线上移、湍流强度下降；与光滑表面相比，脊状表面的位移厚度和动量损失厚度明显减小，也表明脊状表面具有减阻效果；位移厚度和动量损失厚度减少量随槽间距s^＋的增加呈现先变大后变小的趋势，在S^＋=12时达到最大。     

脊状表面减阻机理研究

针对脊状表面流场的特点,通过实验测量和数值模拟的方法对脊状表面微观流场进行了深入研究,获得了脊状表面湍流边界层的时均速度分布曲线、湍流度分布曲线和微观流场结构.为了得到脊状结构对壁面物性的影响,对脊状表面进行了疏水性测试,获得了液滴在脊状表面上的表观接触角,并通过水洞试验验证了脊状表面的减阻效果.研究表明,与光滑表面相比,脊状表面微观流场结构中存在"二次涡",近壁区的黏性底层厚度比平板的要厚得多,湍流度显著降低,且脊状表面表现出明显的疏水性.由此提出了基于壁面隔离效应、增大湍流阻尼效应和改变壁面物性效应的减阻机理.     

柔性壁面湍流减阻机理与多尺度相干结构控制的实验研究

用热膜测速仪以高于对应最小湍流时间尺度的分辨率,精细测量了水槽中刚性壁面和柔性壁面平板湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体粘性系数、壁面摩擦切应力等内尺度物理量的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,通过非线性迭代求解壁面摩擦速度以及湍流边界层壁面摩擦切应力.结果表明柔性壁的湍流边界层速度分布在对数律层有所上移,缓冲层增厚,说明柔性壁面具有一定的减阻作用. 利用湍流多尺度局部平均结构函数的概念和多尺度局部平均结构函数的瞬时强度因子、平坦因子检测多尺度相干结构及其间歇性的方法,提取了湍流边界层多尺度相干结构的条件相位平均波形.对比研究了刚性壁面和柔性壁面平板湍流边界层近壁区域多尺度相干结构的条件相位平均波形及其间歇性的统计特征,分析了柔性壁面具有减阻作用的物理机理.     

用平均速度剖面法测量壁湍流摩擦阻力

用IFA300恒温热线风速仪精细测量风洞中不同雷诺数流动条件下的平板湍流边界层近壁区域对数律平均速度剖面．利用平板湍流边界层近壁区域的对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系，在准确测量平板湍流边界层近壁区域对数律平均速度剖面的基础上，测量平板湍流边界层的壁面摩擦阻力．实现了平板湍流边界层壁面摩擦阻力的无干扰或微小干扰测量．该种方法操作简便，不需要在流场中安装测力天平、传感器等复杂的测量装置，不需要对湍流边界层的壁面进行破坏，不会影响湍流边界层壁面附近区域原有的流场条件，是一种切实可行的测量平板湍流边界层壁面摩擦阻力的简便方法．     

曲率和旋转对离心叶轮叶片上湍流边界层的影响

本文将曲率和旋转项引入二维湍流边界层动量方程中,导出动量损失厚度的积分关系式。分析了曲率和旋转对湍流结构的直接影响,并提出壁面速度分布律的修正表达式。     

输气管道壁面涂料减阻机理的实验研究

用IFA-300热线风速仪以高于对应最小湍流时间尺度的分辨率精细测量了风洞中不同壁面涂料的管道湍流边界层不同法向位置流向速度分量的时间序列信号,利用湍流边界层近壁区域对数律平均速度剖面与壁面摩擦速度、流体黏性系数等内尺度物理量的关系和壁面摩擦速度与壁面摩擦切应力的关系,在准确测量湍流边界层近壁区域对数律平均速度剖面的基础上,间接测量湍流边界层的壁面摩擦阻力．对不同壁面涂料的壁湍流脉动速度信号用子波分析进行多尺度分解,用子波系数的瞬时强度因子和平坦因子检测管道湍流边界层中的多尺度相干结构,提取不同尺度相干结构的条件相位平均波形,对比研究输气管道壁面涂料的减阻机理．     

TRPIV MEASUREMENT OF DRAG-REDUCTION IN THE TURBULENT BOUNDARY LAYER OVER RIBLETS PLATE

采用高时间分辨率粒子图像测速技术对沟槽壁面平板湍流边界层速度矢量场的时间序列及其统计量进行了实验测量,讨论了在同一来流速度下沟槽壁面对平均速度剖面﹑雷诺切应力及湍流强度的影响. 用流向速度分量的多尺度空间局部平均结构函数辨识壁湍流多尺度相干结构,用条件采样和相位平均技术提取壁湍流多尺度相干结构喷射和扫掠事件的脉动速度、展向涡量的二维空间拓扑形态. 结果表明,与同材料光滑壁面对比,沟槽壁面实现了10.73%的摩阻减小量;沟槽壁面湍流边界层湍流强度及雷诺切应力皆比光滑平板湍流边界层对应统计量小,说明沟槽壁面有效降低了湍流边界层内流体的脉动. 通过比较壁湍流相干结构猝发事件各脉动速度分量与展向涡量的空间分布特征,肯定了沟槽壁面的减阻效果,发现沟槽壁面通过抑制相干结构猝发事件实现减阻.     

倾斜吹吸控制下湍流边界层减阻的直接数值模拟

雷诺切应力是壁湍流高摩擦阻力的重要来源, 有理论认为可以通过壁面生成负雷诺应力(数值上为正)的方式来削弱湍流流场中雷诺应力的分布, 以此获得流动减阻. 而通过对雷诺平均运动方程的法向二次积分, 可以发现壁面生成正雷诺应力(数值上为负)对壁面摩擦阻力系数才有负贡献. 文中在湍流边界层流动的控制区域下边界设置一系列倾斜狭缝, 利用该装置通过周期性吹吸的方法产生壁面生成正(负)雷诺应力, 并采用直接数值模拟方法考察和验证上文提到的减阻理论. 文中采用的湍流边界层流动模型, 其流动雷诺数(基于外流速度及动量损失厚度)从300 发展到860. 文中通过多组数值模拟算例, 考察了射流强度和频率对壁面摩擦阻力系数的影响, 并对比了壁面生成正或负雷诺应力对流动的影响. 研究表明, 壁面生成正雷诺应力控制的减阻率能达到3.26, 而壁面生成负雷诺应力控制的减阻效果较壁面生成正雷诺应力控制的要差; 壁面生成的正雷诺应力对壁面摩擦阻力有负贡献, 而壁面生成的负雷诺应力对壁面摩擦阻力有正贡献; 通过考察控制的收支比, 发现控制方案不能获得能量净收益.      

用平均速度剖面法测量湍流边界层壁面摩擦速度的对比研究

基于不同雷诺数平板湍流边界层平均速度剖面,分别采用黏性底层拟合、对数律区拟合以及Spalding公式拟合算法计算了壁面摩擦速度,并对平均速度剖面进行无量纲化。通过比较无量纲化的平均速度剖面与理论规律曲线,验证了三种拟合计算方法的有效性。通过比较三种拟合算法所得的壁面摩擦速度与油膜干涉法直接测得的壁面摩擦速度之间的误差,并分析不同拟合算法误差形成的内在机制,验证了三种拟合算法计算结果的准确性与可靠性。结果表明Spalding拟合算法计算结果的准确性和可靠性都要优于其他两种拟合算法。     

脊状表面航行器模型减阻特性的风洞实验研究

针对航行器提高航程和航速的需要,开展脊状表面湍流边界层减阻的实验和数值仿真研究。在航行器模型的外表面加工具有特定形状、尺寸的脊状结构,导致湍流边界层的流动稳定性增强,壁面摩擦阻力降低。在风洞中对具有光滑表面和脊状表面的航行器模型在不同风速和攻角下进行阻力测试,得到其减阻特性曲线。实验结果表明,具有横向脊状表面的航行器模型在一定来流速度范围内具有很好的减阻效果,实验获得的最大减阻量为23.5%。数值仿真结果则发现,在脊状结构内形成了稳定的"二次涡",边界层内湍动能和湍流猝发强度降低,很好地揭示了减阻机理。     

Flow field analysis of a turbulent boundary layer over a riblet surface

The near-wall flow structures of a turbulent boundary layer over a riblet surface with semi-circular grooves were investigated experimentally for the cases of drag decreasing (s ⁺=25.2) and drag increasing (s ⁺=40.6). One thousand instantaneous velocity fields over riblets were measured using the velocity field measurement technique and compared with those above a smooth flat plate. The field of view was 6.75 × 6.75 mm² in physical dimension, containing two grooves. Those instantaneous velocity fields were ensemble averaged to get turbulent statistics including turbulent intensities and turbulent kinetic energy. To see the global flow structure qualitatively, flow visualization was also carried out using the synchronized smoke-wire technique under the same experimental conditions. For the case of drag decreasing (s ⁺=25.2), most of the streamwise vortices stay above the riblets, interacting with the riblet tips frequently. The riblet tips impede the spanwise movement of the streamwise vortices and induce secondary vortices. The normalized rms velocity fluctuations and turbulent kinetic energy are small near the riblet surface, compared with those over a smooth flat plate. Inside the riblet valleys, these are sufficiently small that the increased wetted surface area of the riblets can be compensated. In addition, in the outer region (y ⁺ > 30), these values are almost equal to or slightly smaller than those for the smooth plate. For the case of drag increasing (s ⁺=40.6), however, most of the streamwise vortices stay inside the riblet valleys and contact directly with the riblet surface. The high-speed down-wash flow penetrating into the riblet valley interacts actively with the wetted riblet surface and increases the skin friction. The rms velocity fluctuations and turbulent kinetic energy have larger values compared with those over a smooth flat plate. Received: 24 March 1999/Accepted: 10 March 2000     

Riblet modelling using a second-moment closure

A low Reynolds number second-moment closure has been used to calculate a turbulent boundary layer which develops over a riblet surface with zero pressure gradient. The calculated mean velocity distributions compare favourably with measurements. Calculated Reynolds stresses away from the riblet surface region are also in agreement with measurements. In the vicinity of the riblets, the model reflects the increased anisotropy of the Reynolds stress tensor inadequately. Possible reasons for this shortcoming are discussed and suggestions for improving the model are made.     

Large-scale spanwise periodicity in a turbulent boundary layer induced by highly ordered and directional surface roughness

The effect of converging–diverging riblet-type surface roughness (riblets arranged in a ‘herringbone’ pattern) are investigated experimentally in a zero pressure gradient turbulent boundary layer. For this initial parametric investigation three different parameters of the surface roughness are analysed in detail; the converging–diverging riblet yaw angle α, the streamwise fetch or development length over the rough surface F_x and the viscous-scaled riblet height h⁺. It is observed that this highly directional surface roughness pattern induces a large-scale spanwise periodicity onto the boundary layer, resulting in a pronounced spanwise modification of the boundary layer thickness. Hot-wire measurements reveal that above the diverging region, the local mean velocity increases while the turbulent intensity decreases, resulting in a thinner overall boundary layer thickness in these locations. The opposite situation occurs over the converging region, where the local mean velocity is decreased and the turbulent intensity increases, producing a locally thicker boundary layer. Increasing the converging–diverging angle or the viscous-scaled riblet height results in stronger spanwise perturbations. For the strongest convergent–divergent angle, the spanwise variation of the boundary layer thickness between the diverging and converging region is almost a factor of two. Such a large variation is remarkable considering that the riblet height is only 1% of the unperturbed boundary layer thickness. Increasing the fetch seems to cause the perturbations to grow further from the surface, while the overall strength of the induced high and low speed regions remain relatively unaltered. Further analysis of the pre-multiplied energy spectra suggests that the surface roughness has modified or redistributed the largest scale energetic structures.     

固体颗粒对沟槽湍流边界层影响的实验研究

本文采用粒子图像测速技术(particles image velocimetry, PIV)研究固体颗粒对放置在平板湍流边界层中的平壁和沟槽壁面减阻效果的影响. 实验对清水和加入粒径为155 μm聚苯乙烯颗粒的流法向二维速度场信息进行采集, 对不同工况下的平均速度剖面、雷诺应力和湍流度等统计量进行对比, 分析流体在边界层中的行为. 运用空间局部平均结构函数提取了不同工况湍流边界层喷射?扫掠行为的空间拓扑结构并进行比较. 结果发现, 在不同的壁面条件下, 粒子加入后的对数律区中无量纲速度均略大于清水组, 雷诺切应力有所降低, 湍流度有所减弱. 对于不同流场速度下的沟槽而言, 颗粒的加入均降低了壁面附近的阻力, 而颗粒单独作用于光滑壁面的减阻效果并不明显. 加入粒子后的相干结构数目有所增加, 法向脉动速度下降. 沟槽壁面附近的相干结构数目有所增加, 法向脉动速度在自由来流速度较大时有所上升, 在速度较小时有所下降. 这表明不同减阻状况下的沟槽均能将大涡破碎成更多的涡, 并且粒子的加入强化了这种破碎作用.      

Riblet flow calculation with a low Reynolds number κ - ε model

A low Reynolds number κ - ε model has been used to calculate the turbulent boundary layer over riblets. Calculated mean velocity, Reynolds shear stress and kinetic energy distributions are generally in good agreement with available experimental data. The comparison between these distributions and those in a corner flow points to a significant difference between the two flows and the unlikelihood of counter-rotating vortices within the riblet grooves. One shortcoming of the present κ - ε model is the relatively slow return to a two-dimensional turbulence state as the distance from the riblet surface increases.     

Numerical and experimental investigation of the laminar boundary layer over riblets

One of the main aims of this work is to show to what extent drag reduction in a turbulent boundary layer can be ascribed to a purely viscous effect. A numerical and experimental study is performed in a laminar boundary layer over triangular riblets. The 2-D parabolic equations of motion are integrated using an x marching method and the discretised system is solved with the MSI algorithm. The influence of the riblet geometrical parameters and of the number of grid points is studied. Measurements are carried out in a water tunnel with forward scatter and backscatter laser-Doppler velocimetry extending within the riblets. The longitudinal velocity component measurements and computations are practically identical. Numerical results presented herein show that a slight drag reduction is obtained for s/h=1.2. It appears that, as far as friction is concerned, the wetted area is not the surface to be considered. Thus, the boundary layer over riblets would behave like a boundary layer on an equivalent smooth plate located beneath the crest plane. The numerical study in terms of the riblet height h shows best results are for h tending to zero, with the ratio s/h being equal to 1.2.     

Riblet drag reduction in mild adverse pressure gradients: A numerical investigation

Riblet films are a passive method of turbulent boundary layer control that can reduce viscous drag. They have been studied with great detail for over 30 years. Although common riblet applications include flows with Adverse Pressure Gradients (APG), nearly all research thus far has been performed in channel flows. Recent research has provided motivation to study riblets in more complicated turbulent flows with claims that riblet drag reduction can double in mild APG common to airfoils at moderate angles of attack. Therefore, in this study, we compare drag reduction by scalloped riblet films between riblets in a zero pressure gradient and those in a mild APG using high-resolution large eddy simulations. In order to gain a fundamental understanding of the relationship between drag reduction and pressure gradient, we simulated several different riblet sizes that encompassed a broad range of s⁺ (riblet width in wall units), similarly to many previously published experimental studies. We found that there was only a slight improvement in drag reduction for riblets in the mild APG. We also observed that peak values of streamwise turbulence intensity, turbulent kinetic energy, and streamwise vorticity scale with riblet width. Primary Reynolds shear stresses and turbulence kinetic energy production however scale with the ability of the riblet to reduce skin-friction.