Buckling investigations on a nuclear reactor inner vessel model

This paper presents the results of an experimental study on the buckling of scaled-down models of the inner vessel used in nuclear reactor structures. The inner vessel, a shell of composite geometry, consists of two cylindrical shells connected by conical and torus shells. There are six stand-pipes on the conical portion of the vessel carrying heat exchangers and pumps. Scaled-down models of the inner vessel are made by the conventional fabrication methods (rolling, welding) and are tested in the present study. The test setup consists of a loading system for applying concentrated load on the stand-pipes, an air compressor for applying internal pressure and the related instrumentation. Imperfection scans are carried out in a specially fabricated experimental setup using linear variable differential transformers (LVDTs) before and during loading. Using the scanned raw data, the initial geometric imperfections and eccentricity between the LVDTs and the specimen axes at different axial locations are calculated. The results show that the maximum initial imperfections are on the order of 1.75 times the wall thickness; generally, the growth of deformation patterns with loading resembles the shapes of initial imperfections, and the growth is predominant on lower cylinder and torus regions. The general purpose, finite element-based software, ABAQUS, is used to obtain the analytical values. The initial imperfections measured on the experimental models are incorporated into the finite element models. The agreement between experimental and analytical buckling loads is within about 30 percent error.     

Buckling analysis of functionally graded material (FGM) sandwich truncated conical shells reinforced by FGM stiffeners filled inside by elastic foundations

An analytical solution for buckling of an eccentrically stiffened sandwich truncated conical shell is investigated. The shell consists of two functionally graded material (FGM) coating layers and a core layer which are metal or ceramic subjected to an axial compressive load and an external uniform pressure. Shells are reinforced by stringers and rings, in which the material properties of shells and stiffeners are graded in the thickness direction following a general sigmoid law distribution. Two models of coated shell-stiffener arrangements are investigated. The change of the spacing between stringers in the meridional direction is taken into account. A couple set of three-variable-coefficient partial differential equations in terms of displacement components are solved by the Galerkin method. A closed-form expression for determining the buckling load is obtained. The numerical examples are presented and compared with previous works.     

Free vibrations of rotating composite conical shells with stringer and ring stiffeners

In this paper, an analytical solution for the free vibration of rotating composite conical shells with axial stiffeners (stringers) and circumferential stiffener (rings), is presented using an energy-based approach. Ritz method is applied while stiffeners are treated as discrete elements. The conical shells are stiffened with uniform interval and it is assumed that the stiffeners have the same material and geometric properties. The study includes the effects of the coriolis and centrifugal accelerations, and the initial hoop tension. The results obtained include the relationship between frequency parameter and circumferential wave number as well as rotating speed at various angles. Influences of geometric properties on the frequency parameter are also discussed. In order to validate the present analysis, it is compared with other published works for a non-stiffened conical shell; other comparison is made in the special case where the angle of the stiffened conical shell goes to zero, i.e., stiffened cylindrical shell. Good agreement is observed and a new range of results is presented for rotating stiffened conical shells which can be used as a benchmark to approximate solutions.     

圆柱壳稳定性问题的研究进展

圆柱壳是工程实际中广泛应用的结构,其主要破坏形式是屈曲失稳．作为力学领域的经典问题,圆柱壳稳定性问题的研究非常之多．其中,受均匀轴向压力的圆柱壳由于临界屈曲载荷的理论预测值与早期试验结果之间的巨大差异,更是推动了壳体稳定性理论的不断发展．本文简要回顾了壳体稳定性理论的发展和分类,并对轴压圆柱壳体试验结果分散且远低于理论预测值的原因及含缺陷圆柱壳体的稳定性研究方法进行了总结,然后综述了地下空间顶管、储油罐、加筋圆柱壳及脱层圆柱壳等实际工程中广泛应用的圆柱壳结构稳定性研究的现状和趋势,最后展望了将来对工程应用中圆柱壳结构的稳定性研究的难点和方向．     

Postbuckling of imperfect stiffened cylindrical shells under combined external pressure and heating

1.IntroductionStiffenedcylindricalshellsarewidelyusedinmanytypesofstructures.Inpracticetheyoftensubjecttovarioustypesofcombinedthermalandmechanicalloadingandmayhavesignificantandunavoidableinitialgeometricalimperfections.Therefore,thepostbucklingbehaviorofimperfectstiITenedcylindricalshellsundercombinedexternalpress.ureandthermalloadingmustbewellunderstood.Manypostbucklingstudieshavebeenmadetbrstiffenedcylindricalshellsunderpureaxialcompression,uniformexternalpressureortheircombinations,where…     

Torsional postbuckling characteristics of functionally graded graphene enhanced laminated truncated conical shell with temperature dependent material properties

Buckling and postbuckling characteristics of laminated graphene-enhanced composite (GEC) truncated conical shells exposed to torsion under temperature conditions using finite element method (FEM) simulation are presented in this study. In the thickness direction, the GEC layers of the conical shell are ordered in a piece-wise arrangement of functionally graded (FG) distribution, with each layer containing a variable volume fraction for graphene reinforcement. To calculate the properties of temperature-dependent material of GEC layers, the extended Halpin-Tsai micromechanical framework is used. The FEM model is verified via comparing the current results obtained with the theoretical estimates for homogeneous, laminated cylindrical, and conical shells, the FEM model is validated. The computational results show that a piece-wise FG graphene volume fraction distribution can improve the torque of critical buckling and torsional postbuckling strength. Also, the geometric parameters have a critical impact on the stability of the conical shell. However, a temperature rise can reduce the crucial torsional buckling torque as well as the GEC laminated truncated conical shell's postbuckling strength.     

轴向应力波作用下圆柱壳塑性轴对称动力屈曲

运用有限元特征值分析方法对应力波作用下圆柱壳塑性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的特征方程,在分析中同时考虑了应力波效应及横向惯性效应,把圆柱壳塑性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳塑性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

基于混合变量条形传递函数方法的圆柱壳屈曲分析

提出了一种分析交各向异性圆柱壳和阶梯圆柱壳稳定性问题的混合变量条形传递函数方法。首先基于Fluegge薄壳理论，通过定义广义位移变量和对应的广义力变量，建立了圆柱壳混合变量能量泛函；然后通过引入条形单元，定义混合状态变量和采用传递函数方法对超级壳单元求解，得到具有多种边界条件圆柱壳屈曲问题的半解析解；最后通过位移连续和力平衡条件，可以得到阶梯圆柱壳屈曲问题的解。理论解推导过程表明此方法在引入边界条件和进行阶梯圆柱壳求解时非常方便。算例分析的结果验证了本方法的正确性。     

Vibrations and buckling of eccentrically loaded stiffened cylindrical shells

The influence of eccentricity of loading on the vibrations and buckling of stringer-stiffened shells is studied. An established nonlinear theory, which takes into account nonlinear prebuckling, is applied and the predictions are compared with experimental results. Two families of shells, one ‘heavily’ stiffened and the other ‘moderately’ stiffened, were tested but detailed results are presented only for the ‘heavily’ stiffened shells. In each family there are three identical shells, each with different eccentricity of loading. In all cases, different in-plane-boundary conditions are considered and correlated with experimental results.     

轴向应力波作用下圆柱壳弹性轴对称动力失稳有限元特征值分析

本文运用有限元特征值分析方法对应力波作用下圆柱壳弹性轴对称动力失稳问题进行了研究。基于应力波理论和相邻平衡准则导出了圆柱壳轴对称动力失稳时的有限元特征方程,在此方程中考虑了应力波效应及横向惯性效应,把圆柱壳弹性动力失稳问题归结为特征值问题。通过引入圆柱壳动力失稳时的波前约束条件实现了此类问题的有限元特征值解法。计算结果揭示了圆柱壳弹性轴对称动力屈曲变形发展的机理,以及轴向应力波和屈曲变形的相互作用规律。     

在均布外压作用下复合材料三角形网格加筋圆锥壳体总体稳定性分析

本文在文献[1]的基础上加以推广,分析了在均布外压作用下复合材料三角形网格加筋圆锥壳体总体稳定性,考虑了蒙皮的正交拉弯耦合效应和加筋筋条的偏心效应.基于外压实验观察结果,通过选择恰当的位移分量表达式,本文利用Galerkin法获得了临界外压的近似表达式,并对某一C/E复合材料三角形内网格加筋圆锥壳体的临界外压值进行了理论计算,所得结果与实验值相当吻合.文中所得结果可供工程应用参考.     

Repeated buckling and its influence on the geometrical imperfections of stiffened cylindrical shells under combined loading

The present experimental study aims at providing better inputs for improvement of the buckling load predictions of stiffened cylindrical shells subjected to combined loading. The work focuses on two main factors which considerably affect the combined buckling load of stiffened shells, namely geometric imperfections and boundary conditions. Six shells with nominal simple supports were tested under various combinations of axial compression and external pressure. The vibration correlation technique is employed to define the real boundary conditions. The geometric imperfections of the integrally stiffened shells are measured in the present experiments in situ and are used as inputs to a multimode analysis which yields the corresponding “knockdown” factor for various combinations of loading. Thus, when employing the repeated buckling procedure for obtaining interaction curves, each point on the curve is adjusted (using the multimode analysis) for the measured “new” surface of the shell and this results in more realistic interaction curves. The geometrical imperfections of the preloaded shells can also serve as an input to the International Imperfection Data Bank for future studies on the correlation between the manufacturing method of the shell and their geometric imperfections.     

Buckling and postbuckling of stiffened cylindrical shells under axial compression

Buckling and postbuckling behaviors of perfect and imperfect,stringer andorthotropically stiffened cylindrical shells have been studied under axial compression.Based on the boundary layer theory for the buckling of thin elastic shells suggested in ref.[1],a theoretical analysis is presented.The effects of material properties of stiffeners andskin,which are made of different materials,on the buckling load and postbuckling behaviorof stiffened cylindrical shells have also been discussed.     

Comparisons of test and theory for nonsymmetric elastic-plastic buckling of shells of revolution

Experimental and analytical buckling pressures are presented for very carefully fabricated thin cylindrical shells with 45, 60 and 75° conical heads and for cylindrical shells with torispherical heads pierced by axisymmetric cylindrical nozzles of various thicknesses and diameters. Nonsymmetric buckling occurs at pressures for which some of the material is loading plastically in the neighborhoods of stress concentrations caused by meridional slope discontinuities. The buckling pressures for the cone-cylinder vessels are predicted within 2.6 per cent and for the pierced torispherical vessels within 4.4 per cent with use of BOSOR5, a computer program based on the finite difference energy method in which axisymmetric large deflections, nonlinear material properties and nonsymmetric bifurcation buckling are accounted for. The predicted buckling pressures of the pierced torispherical specimens are rather sensitive to details of the analytical model in the neighborhood of the juncture between the nozzle and the head. The buckling pressures of the cone-cylinder vessels can be accurately predicted by treatment of the wall material as elastic, enforcement of the full compatibility conditions at the juncture in the prebuckling analysis, and release of the rotation compatibility condition in the bifurcation (eigenvalue) analysis.     

F E M analysis of delamination buckling in composite plates and shells

ＩｎｔｒｏｄｕｃｔｉｏｎＴｈｅｐｒｏｂｌｅｍｏｆｄｅｌａｍｉｎａｔｉｏｎｂｕｃｋｌｉｎｇｏｆｃｏｍｐｏｓｉｔｅｌａｍｉｎａｔｅｓｈａｓｇｅｎｅｒａｔｅｄｓｉｇｎｉｆｉｃａｎｔｒｅｓｅａｒｃｈｉｎｔｅｒｅｓｔｓａｎｄｈａｓｂｅｅｎｔｈｅｓｕｂｊｅｃｔｏｆｍａｎｙｔｈｅｏｒｅｔｉｃａｌｉｎｖｅｓｔｉｇａｔｉｏｎｓｉｎｔｈｉｓｄｅｃａｄｅ.Ａｆｉｎｉｔｅｅｌｅｍｅｎｔｍｏｄｅｌ[1]ｗａｓｐｒｅｓｅｎｔｅｄｔｏｓｏｌｖｅｔｈｅｐｏｓｔ＿ｂｕｃｋｌｉｎｇｐｒｏｂｌｅｍｏｆｃｏｍｐｏｓｉｔｅｐｌａｔｅｓｗｉｔ…     

Thermal buckling and free vibration of FG truncated conical shells with stringer and ring stiffeners using differential quadrature method

In this paper, thermal buckling and free vibration of orthogonally stiffened functionally graded truncated conical shells in thermal environment is investigated. Conical shell has been stiffened by rings and stringers, and the influences of the stiffeners are evaluated by the aid of smearing method. The material properties of the structure are assumed to be changed continuously in the thickness direction. First, the initial thermal stresses are obtained accurately by solving the thermoelastic equilibrium equations. Then, by taking into account the initial thermal stresses, equations of motion as well as boundary conditions are obtained, applying the Hamilton’s principle and the first-order shear deformation theory. The natural frequencies of the system have been achieved, solving these governing equations with considering Differential Quadrature Method (DQM). In addition to Eigen frequency analysis, the critical buckling-temperature of the conical shell has been computed. Moreover, the effects of geometrical parameters, number of stiffeners, thermal environment and various boundary conditions on natural frequency of the system have been investigated. Finally, in order to validate the present work, the results are compared with those of other researches available in literature.     

Stability and limit states of elastoplastic spherical shells under static and dynamic loading

The problem of elastoplastic deformation, buckling, and postcritical behavior of spherical shells is solved using a finite element method and a cross-type explicit scheme of time integration. Stability problems for hemispherical shells under external pressure and compression between rigid plates are considered. The influence of holes and boundary conditions on shell deformation is investigated. It is shown that the calculation results are in good agreement with experimental data.     

Mechanical and thermal postbuckling of FGM thick circular cylindrical shells reinforced by FGM stiffener system using higher-order shear deformation theory

The postbuckling of the eccentrically stiffened circular cylindrical shells made of functionally graded materials(FGMs),subjected to the axial compressive load and external uniform pressure and filled inside by the elastic foundations in the thermal environments,is investigated with an analytical method.The shells are reinforced by FGM stringers and rings.The thermal elements of the shells and stiffeners in the fundamental equations are considered.The equilibrium and nonlinear stability equations in terms of the displacement components for the stiffened shells are derived with the third-order shear deformation theory and Leckhniskii smeared stiffener technique.The closed-form expressions for determining the buckling load and postbuckling load-deflection curves are obtained with the Galerkin method.The effects of the stiffeners,the foundations,the material and dimensional parameters,and the pre-existent axial compressive and thermal load are considered.     

安全壳中钢衬壳热屈曲问题理论与实验研究（Ⅱ）—实验部分

钢衬壳热屈曲问题是核工程安全壳设计中的主要问题,但实验研究方面的文章发表得不多。文中以２００兆瓦核电站安全壳中钢宙为研究对象,采用局部１：１模型,测得了钢衬壳热屈曲温度和应变载荷,给出了钢衬壳屈曲和初始后屈曲过程中挠度和温度关系。     

U型波纹管及相关结构环向屈曲的有限元分析(Ⅰ)--基本方程及环板的屈曲

U型波纹管是现代管道系统中最常见的一种位移补偿器 ,它由环板和具有正、负Gauss曲率的半圆环壳组成 ,在管道所传输的介质的压力作用下会发生屈曲。其中环向屈曲最为复杂 ,精确的理论分析非常困难 ,有限元分析也不多见。作者在分析前人工作的基础上 ,以圆环壳段为单元 (特定的旋转壳段单元 ,能自动退化成环板单元 ) ,限于弹性范围和线性化特征值问题 ,对介质压力作用下U型波纹管及其相关结构 (圆环板、圆环壳、半圆环壳 )的环向屈曲问题进行了分析。考虑了结构屈曲前的弯曲 ,计及压力的二次势能 ,导出的应力刚度矩阵和载荷刚度矩阵是非对称的。全部工作分为三部分 :(Ⅰ )基本方程 ,环板的屈曲 ;(Ⅱ )圆环壳、半圆环壳的屈曲 ;(Ⅲ )波纹管平面失稳的机理。本文为第一部分 ,除推导公式外 ,对不同边界和不同内外径之比的环板在径向均匀压力作用下的环向屈曲进行了计算 (轴对称的径向屈曲作为特例得到 ) ,给出了前屈曲应力分布、临界载荷及相应的屈曲模态 ,并将临界压力的值与前人基于vonK偄ｒｍ偄ｎ大挠度板的精确解进行了比较 ,吻合良好。