圆柱尾迹涡的三维演化及结构特征

应用无粘涡丝运动学理论和局部诱导近似(LIA)方法,以Lagrange观点跟踪涡丝在背景流场中运动,用数值方法研究了中等Re数(≈10~3)下圆柱分离尾迹中Kármán涡和涡辫区涡丝的三维演化的机制和动力学过程,及其结构特征。背景流场考虑为尾迹时间平均速度流场和Kármán涡街流场。初始展向小扰动为指数形式和谐波形式。结果指出:Kármán涡和涡辫区中的涡丝具有展向不稳定性,形成流向涡量。在尾迹的初期输运过程中,表现出有序的大、小尺度涡结构。并进一步分析了其产生的机理。     

逆向涡对超疏水壁面减阻影响的TRPIV实验研究

超疏水壁面由于具有减阻和自清洁功能而成为国内外减阻和海洋防污等研究领域的热点之一,而20世纪湍流中相干结构的发现为湍流的控制指出新的方向,尤其近壁区涡结构对摩擦阻力贡献很大.利用高时间分辨率粒子图像测速技术,研究了超疏水壁面(SH)以及亲水壁面(PH)湍流边界层中正负展向涡的空间分布特征,研究逆向涡对超疏水壁面近壁区流动结构的影响和超疏水壁面的减阻机理.首先利用空间多尺度局部平均涡量的概念提取壁湍流发卡涡展向涡头(顺向涡)和逆向涡,实现了准确识别涡心并排除小尺度涡的干扰;然后根据检测到的顺向涡和逆向涡流线分布图,发现逆向涡始终处于正向涡的上游和下方,并且对正向涡的进一步发展起抑制作用;最后对两种壁面边界层中逆向涡数量以及出现概率进行对比,发现具有减阻效果的超疏水壁面边界层中出现更多逆向涡.说明逆向涡可抑制上方顺向涡与壁面的强烈剪切,并使靠近壁面的流体加速,从而产生减阻效果;超疏水壁面中涡结构具有更大的β角,使其更好地阻碍了发卡涡头附近强烈的喷射和扫略;超疏水壁面逆向涡出现概率明显大于亲水壁面.这些结果表明:超疏水壁面表现出的减阻特性(Reδ≈13 500,减阻5.8%)与两板产生逆向涡的差异有关.     

可压缩自由剪切流混合转捩大涡模拟

针对湍流气动光学效应与冲压发动机气体混合机理问题,开展了可压缩混合层流动空间模式大涡模拟和时间模式直接数值模拟研究.通过对流场(包含亚/亚混合、超/亚混合两种情况)失稳、转捩直至完全湍流的空间发展过程的研究表明,对流Mach数0.4状态下流场失稳以二维最不稳定扰动为主;非线性发展中,基频涡对并及展向涡撕裂主控流动转捩,流场发生混合转捩;转捩后脉动流场基本达到局部各向同性,此时,湍流Mach数低于0.3,流动压缩性可近似忽略.     

横向紊动射流的数值与实验研究进展

横向紊动射流作为流体运动的一种重要类型,广泛存在于如: 燃气轮机气膜冷却、锅炉燃烧室等的燃烧控制, V/STOL(垂直或短距离起落)飞机、废气排放的控制等工程实际应用中.由于射流的存在,增加了流场的复杂性,流场中同时存在射流剪切层涡、马蹄形涡系、反向旋涡对和尾迹涡等4种涡系结构,这对流体力学理论研究具有重要意义.长期以来,研究人员从理论分析、实验测量和数值模拟方面对横向紊动射流进行了大量的研究工作,目前已经认识了流场中的许多流动特性和流动机理.从数值模拟和实验研究两个方面,比较并分析了国内外横向紊动射流研究的现状和研究结果,评述了不同湍流模型以及不同的实验测量方法对横向紊动射流的预测能力,讨论了存在的问题并对该领域的研究方向进行了展望.      

水下发射航行体尾涡不稳定性分析

在水下连续发射过程中前一发航行体尾流会对后一发航行体运动姿态稳定性产生流动干扰现象. 因此, 研究尾流中涡旋结构演变机理对解决多弹体水下连续发射流动干扰难题具有重要的意义. 本文采用改进型分离涡模型与能量方程, VOF多相流模型与重叠网格技术相结合方法, 对航行体水下发射尾流演变过程开展精细化模拟研究, 其中模拟结果和实验吻合度较好, 验证了本文数值方法的有效性. 以航行体尾流区域为重点研究对象, 分析了尾流区瞬态流场分布, 讨论了横流强度和雷诺数对尾涡结构演变以及脉动压力分布特性的影响. 结果表明: 由于尾流区高速流体核心区与低速自由流相互作用导致Kelvin-Helmholtz不稳定现象出现, 可以清晰地发现涡旋结构在剪切力的作用下发生脱落. 在横流条件下, 航行体尾端脱落的涡环与涡腿形成发卡涡, 而多个发卡涡沿轴向间隔排列组成发卡涡包存在于尾流中. 随着横流强度增大, 形成多级发卡涡包结构, 而导致脉动压力二次峰值均出现的主要原因是尾流涡旋流场演变引起的. 随着雷诺数的增大, 尾流中由圆柱形涡和U型涡组成的二次涡结构逐渐明显, 不稳定性加强.      

可压缩燃烧反应转捩混合层直接数值模拟

针对三维时间发展可压缩氢/氧非预混燃烧反应平面自由剪切混合层,采用5阶迎风/6阶对称紧致混合差分格式以及3阶显式Runge-Kutta时间推进方法,直接数值模拟了伴随燃烧产物生成和反应能量释放, 流动受扰动激发失稳并转捩的演化过程. 在转捩初期, 获得了${\it\Lambda}$涡、马蹄涡等典型的大尺度拟序结构,观察到了流动失稳后发生双马蹄涡三维对并的现象, 大尺度结构呈较好的对称性.在流动演化后期, 大尺度结构逐次破碎形成小尺度结构, 混合层进入转捩末期,呈明显的不对称性.      

气泡夹带对壁面油膜流动特性的影响

油-气润滑系统工作过程中,润滑油膜受微油滴冲击和压缩空气扰动影响易形成气泡夹带现象,气泡夹带行为将对壁面润滑油膜层的形成及流动过程产生重要影响。基于VOF数值模拟方法,对含气泡油膜沿倾斜壁面的流动行为进行研究,考察了气泡的存在对油膜形态和流动速度的影响规律,以及气泡破裂阶段空腔邻域内流体压力变化特性。研究表明,油膜夹带气泡的形变和迁移诱发气泡周围微流场的速度扰动现象,导致气液界面处产生非均匀速度梯度分布,进而引发油膜表面的形态波动。气泡发生破裂时,油膜空穴部位发生明显的正负压力波动现象,气泡附近壁面将承受一定的交变载荷作用。     

颗粒物在人体上呼吸道模型中沉降规律的数值研究

本文采用RNG k-ε湍流模型对简化的上呼吸道内的流场进行数值仿真,并结合随机涡相互作用模型对上呼吸道内颗粒的局部运动沉积特性进行了数值模拟研究.结果表明,惯性冲击是微米级颗粒物主要的沉降机理,惯性参量能很好地衡量颗粒的沉降规律.口腔中流动较平稳,颗粒受扰动较小.颗粒由于惯性冲击而运动靠近咽部后部并易于沉积在咽部后壁面...     

高超声速尾迹流场稳定性数值研究

通过数值模拟, 对高超声速尾迹流场进行了研究, 对其尾迹流动的失稳过程进行了分析.选取计算模型为圆球,Ma= 6.0, Re = 1.71\times 10^6(Re以球头半径为参考长度). 通过数值模拟,首先得到的流动是稳定解,在底部发展出一个主分离区和一个二次分离区,流动是轴对称状态. 不添加任何扰动继续进行计算,发现底部流场缓慢发展出微弱的非定常流动. 随后,该现象继续发展,出现明显的结构失稳,得到了无量纲周期为12.0的周期解. 给出了高超声速圆球绕流尾迹结构的周期性演化过程,对其涡系结构的演化及奇点特征进行了分析. 研究表明该数值模拟方法可用于底部流动稳定性问题的研究,同时证实了高超声速底部流动也存在流动不稳定性.      

应用PIV技术测试涡旋波流场

涡旋波流动作为一种特殊的流动现象,可以使流体在相对较宽的槽道中产生较强的波动和对流混合,从而在小Re数条件下起到强化传质的效果。本文利用PIV流场显示技术,对振荡流在非对称槽道中所形成的涡旋波的产生机理和发展规律进行了实验研究和定量分析,测得了涡旋波流场的速度矢量图,阐明了涡旋波流场周期性变化的特点。分析了Re数和St数对涡旋波流动的影响,并得出了旋涡涡心位置以及涡心处涡量的动态变化规律。     

Görtler vortices promoted by wall roughness

Numerical experiments are conducted to investigate spatially developing Görtler vortices and the way in which wall roughness promotes their formation and growth. Several different types of walls are examined and their relative merits as vortex promoters assessed. The only disturbances of the flow are due to the rough wall; hence, at each downstream station the local field feels (1) the upstream flow distribution (produced by the upstream wall conditions) and (2) the local forcing at the wall. Rapid vortex formation and growth, like in the case of ribleted walls, can be qualitatively explained by the positive combination of these two effects; when the two influences on the local flow field compete, e.g. for randomly distributed wall roughness, the equations with the boundary conditions filter the disturbances over some streamwise length, function of the roughness amplitude, to create coherent patches of vorticity out of the random noise. These patches can then be amplified by the instability mechanism. If a thin rough strip is aligned along the span of an otherwise smooth wall to trip the boundary layer, the filtering region is shorter and growth of the vortices starts earlier. Also for the case of an isolated three-dimensional hump a rapid disturbance amplification is produced, but in this case the vortices remain confined and a very slow spanwise spreading of the perturbation occurs. In all naturally developing cases, where no specific wavelengths are explicity favored, the average spanwise wavelengths computed are very close to those of largest growth from the linear stability theory.     

空间发展圆管转捩的直接数值模拟

利用直接数值模拟研究圆管流动中由局部壁面引入的周期性吹吸(PSB)扰动沿流向的空间发展,流动的雷诺数Re选定为3000.在临界幅值的PSB扰动下,在较短的圆管内,圆管中的扰动沿流向快速增长,在足够长的圆管内,扰动沿流向持续增长发生转捩,流动发展到湍流阶段.     

Mixing Intensification on the Edge of a Jet by Means of Longitudinal Vortices

The action of an artificially generated spanwise flow in the form of periodical longitudinal vortices on a plane turbulent mixing layer is investigated. It is shown that the disturbances result in a significant increase in the thickness of the mixing region. For two kinds of spanwise flow, namely, vortices whose centers lie in the plane separating the streams and vortices located above this plane, the dependence of the mixing layer thickness on the vortex amplitude and vertical dimension and on the longitudinal coordinate is found.     

Traveling disturbance appearing in boundary layer transition in a Yawed cylinder

Boundary layers that develop over a body in fluid flow are in most cases three-dimensional owing to the spin, yaw, or surface curvature of the body. Therefore, the study of three-dimensional (3D) boundary-layer transition is essential to work in practical aerodynamics. The present investigation is concerned with the problem of 3D boundary layers over a yawed body. A yawed cylinder model that represents the leading edge portion of a swept wing and the mechanism of crossflow instability are investigated in detail using hot-wire velocimetry and a flow visualization technique. As a result, traveling disturbances having frequencies f₁ and f₂, which differ by about one order of magnitude, are detected in the transition region. The phase velocities and directions of travel of those disturbances are measured. Results for the low-frequency disturbance f₁ show qualitative coincidence with results numerically predicted for a crossflow unsteady disturbance. Nameley, F₁ travels nearly spanwise to the yawed cylinder and very close to the cylinder wall. The results for the high-frequency disturbance f₂ good agreement with the existing experimental results. The ₂ disturbance is found to be the high-frequency inflectional secondary instability that appears in 3D boundary layer transition in general. A two-stage transition process, where stationary crossflow vortices appear as the primary instability and a traveling inflectional disturbance is generated as a secondary instability, was observed. Secondary instability seems to play a major role in turbulent transition.     

Streamwise vortices generated by impinging flows in a confined duct

Particle-tracer technique was employed for visualizing flow structures in a side-inlet square duct. The results obtained indicate that the streamwise vortices developed in the stagnation region of impinging flows are irregularly distributed. As the vortices convect downstream they are first stretched and merged, then squashed due to the non-zero pressure gradient effects caused by the flow separation regions existed along the side walls. The mechanism responsible for generating streamwise vortices in the stagnation region is suggested due to the hydrodynamic instability effect, similar to that previously found for three-dimensional disturbances growing in a two-dimensional stagnation flow.     

横流冲击射流尾迹涡结构的实验研究

本文采用LIF（激光诱导荧光）流动显示和PIV（粒子图像速度场仪）测量对横流冲击射流的尾迹涡结构进行了实验研究。水槽实验是在三种流速比和两种冲击高度实验工况下进行的。由实验结果可得到两种明显的尾迹涡结构、，即射流尾迹涡和横流尾迹涡。横流冲击射流中形成的主要尾迹涡结构主要依赖于流速比。本文还对横流冲击射流近区范围内射流尾迹涡和横流尾迹涡的形成机理和演化特征进行了分析。     

基于MEMS的流动主动控制技术及其研究进展

MEMS技术与流动控制技术的结合, 使得流动主动控制技术的实际应用逐步成为现实, 极大地推动了流动主动控制技术的发展. 简述了流动主动控制技术的基本原理、关键技术, 以及应用MEMS技术实现流动主动控制的机理和途径. 介绍了几家国外研究机构近年来在流动主动控制技术领域基于MEMS技术的微传感、微控制和微执行技术及其集成技术的研究进展, 以及在三角翼前沿涡控制、减阻研究、发动机喷流控制、细长体背风面分离流控制等方面的应用情况.      

Görtler vortices in Falkner–Skan flows with suction and blowing

In this paper, we use nonlinear calculations to study curved boundary‐layer flows with pressure gradients and self‐similar suction or blowing. For an accelerated outer flow, stabilization occurs in the linear region while the saturation amplitude of vortices is larger than for flows with a decelerating outer flow. The combined effects of boundary‐layer suction and a favourable pressure gradient can give a significant stabilization of the flow. Streamwise vortices can be amplified on both concave and convex walls for decelerated Falkner–Skan flow with an overshoot in the velocity profile. The disturbance amplitude is generally lower far downstream compared with profiles without overshoot. Copyright © 2007 John Wiley & Sons, Ltd.     

The nature of near-wall convection velocity in turbulent channel flow

A novel notion of turbulent structure the local cascade structure-is introduced to study the convection phenomenon in a turbulent channel flow. A space-time cross-correlation method is used to calculate the convection velocity. It is found that there are two characteristic convection speeds near the wall, one associated with small-scale streaks of a lower speed and another with streamwise vortices and hairpin vortices of a higher speed. The new concept of turbulent structure is powerful to illustrate the dominant role of coherent structures in the near-wall convection, and to reveal also the nature of the convection-the propagation of patterns of velocity fluctuations-which is scale-dependent.     

The loss of stability of laminar flow in open channel and the mechanism of sand ripple formation

ＩｎｔｒｏｄｕｃｔｉｏｎＤｕｒｉｎｇｔｈｅｔｉｍｅｏｆｂｅｄｓｕｒｆａｃｅｓｅｄｉｍｅｎｔｔｒａｎｓｐｏｒｔａｔｉｏｎ,ｓｅｄｉｍｅｎｔｐａｒｔｉｃｌｅｓｏｆｂｅｄｌｏａｄｍａｋｅｔｈｅｃｏｌｌｅｃｔｉｖｅｍｏｔｉｏｎｏｆｖａｒｉｏｕｓｄｉｆｆｅｒｅｎｔｆｏｒｍｓｏｎｔｈｅｒｉｖｅｒｂｅｄｓｕｒｆａｃｅ,ｔｈｕｓｔｈｅｆｏｒｍｏｆｂｅｄｓｕｒｆａｃｅｃｈａｎｇｅｓｃｏｎｓｔａｎｔｌｙ .Ｔｈｉｓｋｉｎｄｏｆｃｏｌｌｅｃｔｉｖｅｍｏｔｉｏｎｏｆｓｅｄｉｍｅｎｔｐａｒｔｉｃｌｅｓｏｎｔｈｅｂｅｄｓｕｒｆ…