Visualization and structure of confined, milliscale, unsteady impinging slot jets and associated vortices

Flow characteristics of confined, laminar milliscale slot jets are investigated from visualizations, as they impinge upon a flat target plate, with a fully developed velocity profile at the nozzle exit. The effects of Reynolds number Re and normalized nozzle-to-plate distance H/B are considered for a nozzle width B of 1.0 mm. Transition from a stable symmetric jet to an unsteady oscillating jet is observed as the Reynolds number increases (with H/B constant), where the Reynolds number associated with this transition decreases as the normalized nozzle-to-plate distance H/B increases. Instantaneous visualizations show unsteady lateral distortions of jet columns at experimental conditions corresponding to the presence of continuous sinusoidal oscillations, intermittent oscillating motion of the jet column, and jet flow fluctuation/flapping motion. Also apparent in flow visualization sequences are smoke signatures associated with instantaneous vortex structures, which form as secondary flows develop in fluid which, initially, is just adjacent to and within the jet column. Associated jet and vortex structural changes are described as different modes of unsteadiness are present, including characterization of jet column unsteadiness using jet column oscillation frequency, and lateral and streamwise extents of jet distortion.     

Experimental study of parallel and inclined turbulent wall jets

An experimental study of the flow field in a two-dimensional wall jet has been conducted. All measurements were carried out using hot-wire anemometry. The experimental facility has a rectangular slot nozzle of high aspect ratio l/b = 100 (where l and b are the length and height slot, respectively). Mean velocities and Reynolds stresses were determined with three nozzle Reynolds numbers (Re = 1 × 10⁴, 2 × 10⁴ and 3 × 10⁴) and four different inclination angles between the wall and the flow velocity at the nozzle (β = 0°, 10°, 20° and 30°). Results indicate that all wall jets are self-preserving in the developed region. Normal to the wall two regions can be identified: one similar to a plane free jet and the other similar to a boundary layer. Downstream the interaction between these two regions creates a mixed or third region. The logarithmic region increases with the distance from the nozzle and with the Reynolds number. For the inclined wall jet, the spreading rate expressed in terms of jet half-width or maximum velocity decay with respect to the streamwise distance, asymptotes to a linear law. The streamwise locations where the jet becomes self-similar are farther from the exit than in parallel wall jet. The slope of both half-width and maximum velocity decay in the developed region are affected by both wall jet inclination angle and nozzle exit Reynolds number.     

Reynolds number effects on the behavior of a non-buoyant round jet

The behavior of a non-buoyant circular water jet discharged from a contraction nozzle was experimentally investigated. In this experiment, the Reynolds number of the jet, based on the mean velocity results obtained by particle image velocimetry (PIV), ranged from 177 to 5,142. From the experimental results, we found that the cross-sectional profile of the axial velocity for a laminar flow near the nozzle did not show a top-hat distribution, whereas the profiles with Reynolds number higher than 437 were almost top-hat. The length of the zone of flow establishment (ZFE) was found to decrease with increasing Reynolds number. The measured centerline velocity decayed more rapidly and, consequently, approached the theoretical equation earlier near the nozzle as the Reynolds number increased. The decay constant for the centerline velocity of the turbulent cases was relatively lower than that discovered in theory. It is assumed that this probably resulted from the use of the contraction nozzle. Verifying the similarity of the lateral velocity profiles demonstrated that the Gaussian curve was properly approximated only for the turbulent jets and not for the laminar or transitional flows. The jet half width seldom grew for the laminar or transitional flows, whereas it grew with increasing axial distance for the turbulent flows. The spreading rates for the turbulent flows gradually decreased with increasing Reynolds number. The normalized turbulence intensity along the jet centerline increased more rapidly with the axial distance as the Reynolds number increased, and tended to the constant values proposed by previous investigators. The Reynolds shear stress levels were also found to increase as the Reynolds number increased for the turbulent jets.     

Flow structure and heat transfer of impingement jet

This paper presents the characteristics of flow behavior and thermal fields of both free and impingement jets issued from circular orifice nozzle at Re = 9,700. The flow behavior of a single round jet and impingement jet were observed by smoke flow visualization recorded by a high speed video camera with 5,000 frames per second. Heat transfer coefficient on the impingement surface was calculated varying the Reynolds number and the separation distance between nozzle exit and plate. Time-series analysis was applied to the visualization image to get the information of time variation of flow behavior. Probability distribution of vortex scale induced by the jet at discrete positions was investigated. Experimental results show that the potential core is not a continuous phenomenon with time and the frequency of vortex ring formation have similar features regardless of whether the impingement plate was set on or not, furthermore the time-series analysis with flow visualization images makes clear the detailed flow behavior.     

Velocity and Passive Scalar Characteristics in a Round Jet with Grids at the Nozzle Exit

Velocity and passive scalar (temperature) measurements have been made in the near field of a round jet with and without obstructing grids placed at the jet exit. The Reynolds number Re _D (based on the exit centreline velocity and nozzle diameter) is 4.9 × 10⁴ and the flow is incompressible, while the temperature rise does not affect the velocity behaviour. The streamwise development and radial spreading of the passive scalar are attenuated, relative to the unobstructed jet. Close to the jet outlet, the spatial similarity of the moments (up to the third-order) of velocity fluctuations is improved, when the jet is perturbed. An explanation, based on the reduced effect of the large coherent structures in the developing region, is provided.     

Numerical investigation of turbulent free jet flows issuing from rectangular nozzles: the influence of small aspect ratio

In this research, the fluid and thermal characteristics of a rectangular turbulent jet flow is studied numerically. The results of three-dimensional jet issued from a rectangular nozzle are presented. A numerical method employing control volume approach with collocated grid arrangement was employed. Velocity and pressure fields are coupled with SIMPLEC algorithm. The turbulent stresses are approximated using k–e{\varepsilon} model with two different inlet conditions. The velocity and temperature fields are presented and the rates of their decay at the jet centerline are noted. The velocity vectors of the main flow and the secondary flow are illustrated. Also, effect of aspect ratio on mixing in rectangular cross-section jets is considered. The aspect ratios that were considered for this work were 1:1 to 1:4. The results showed that the jet entrains more with smaller AR. Special attention has been drawn to the influence of the Reynolds number (based on hydraulic diameter) as well as the inflow conditions on the evolution of the rectangular jet. An influence on the jet evolution is found for smaller Re, but the jet is close to a converged state for higher Reynolds numbers. The inflow conditions have considerable influence on the jet characteristics.     

Experimental Investigation of Nozzle Exit Reflector Effect on Supersonic Jet

The present study describes an experimental work to investigate the effect of a nozzle exit reflector on a supersonic jet that is discharged from a convergent–divergent nozzle with a design Mach number of 2.0. An annular reflector is installed at the nozzle exit and its diameter is varied. A high-quality spark schlieren optical system is used to visualize detailed jet structures with and without the reflector. Impact pressure measurement using a pitot probe is also carried out to quantify the reflector’s effect on the supersonic jet which is in the range from an over-expanded to a moderately under-expanded state. The results obtained show that for over-expanded jets, the reflector substantially increases the jet spreading rate and reduces the supersonic length of the jet, compared with moderately under-expanded jets. The reflector’s effect appears more significant in imperfectly expanded jets that have strong shock cell structures, but is negligible in correctly expanded jet.     

Dynamics of heavy particles in two swirling jets

We report flow visualisations and laser Doppler anemometry (LDA) velocity measurements in the near field of two swirling jets. The Reynolds number based on jet diameter and bulk velocity at the nozzle exit is 1.4 × 10⁵. In the first jet, a small recirculation region is formed around the jet axis, while, in the second, the streamwise velocity remains positive and overshoots near the jet centre. In both cases, flow visualisations show that the vortex core of the jets is depleted of seeding particles. By using time-averaged distributions of the streamwise and tangential velocities measured at the nozzle outlet, the dynamics of the particles is simulated, by integrating their simplified equations of motion. The particles trajectory thus computed agrees well with that observed in the flow visualisations. Although the turbulence intensity is substantially different in the core of the two jets, its effect on the seeding concentration is localised near the edge of the core.     

Some observations in the vortex-turning behaviour of noncircular inclined jets

An experimental comparison was conducted for Re = 2,500, free elliptic and rectangular jets inclined at 30° and 60° along major or minor planes. Regardless of the jet base geometry, minor-plane inclined jets produced vortex roll-ups that remain inclined. In contrast, major-plane inclined jets produce significantly stronger vortex-roll-up turning behaviour. Interestingly, major-plane inclined rectangular jets exhibit strong vortex-overturning behaviour, where the vortex-roll-up inclination exceeds the 0° incline angle considerably. Vortex-turning extents and rates are compared between major-plane inclined elliptic and rectangular jets here and support present qualitative observations. Closer inspections reveal that the lack of axis-switching phenomenon in major-plane inclined rectangular jets allows vortex-overturning behaviour. In addition, jet centreline deflection is most sensitive in minor-plane inclined jets, where increasing the incline angle leads to a decrease and an increase in the elliptic and rectangular jet deflection, respectively.     

PIV Measurements in the Near and Intermediate Field Regions of Jets Issuing from Eight Different Nozzle Geometries

An experimental study was conducted to investigate the effect of nozzle geometry on the mixing characteristics and turbulent transport phenomena in turbulent jets. The nozzle geometry examined were round, square, cross, eight-corner star, six-lobe daisy, equilateral triangle as well as ellipse and rectangle each with aspect ratio of 2. The jets were produced from sharp linear contoured nozzles which may be considered intermediate to the more widely studied smooth contraction and orifice nozzles. A high resolution particle image velocimetry was used to conduct detailed velocity measurements in the near and intermediate regions. It was observed that the lengths of the potential cores and the growth rates of turbulence intensities on the jet centerline are comparable with those of the orifice jets. The results indicate that the decay and spreading rates are lower than reported for orifice jets but higher than results for smooth contoured jets. The jets issuing from the elliptic and rectangular nozzles have the best mixing performance while the least effective mixing was observed in the star jet. The distributions of the Reynolds stresses and turbulent diffusion clearly showed that turbulent transport phenomena are quite sensitive to nozzle geometry. Due to the specific shape of triangular and daisy jets, the profiles of mean velocity and turbulent quantities are close to each other in their minor and major planes while in the elliptic and rectangular jets are considerably different. They also exhibit more isotropic behavior compared to the elliptic and rectangular jets. In spite of significant effects of nozzle geometry on mean velocity and turbulent quantities, the integral length scales are independent of changes in nozzle geometry.     

Numerical simulation of two‐dimensional laminar slot‐jet impingement flows confined by a parallel wall

Two‐dimensional laminar incompressible impinging slot‐jet is simulated numerically to gain insight into flow characteristics.Computations are done for vertically downward‐directed slot‐jets impinging on a plate at the bottom and confined by a parallel surface on top. The behaviour of the jet with respect to aspect ratio (AR) and Reynolds number (Re) are described in detail. The computed flow patterns for various AR (2–5) and for a range of jet‐exit Reynolds numbers (100–500) are analysed to understand the flow characteristics. The transient development of the flow is also simulated for AR = 4 and Re = 300. It is found that the reattachment length is dependent on both AR and Reynolds number for the range considered. The correlation for reattachment length is suggested. The maximum resultant velocity V_rmax and its trajectory is reported. A detailed study of horizontal velocity profile at different downstream locations is reported. It is found that the effect of Reynolds number and AR is significant to the bottom wall vorticity in the impingement and wall jet regions. Copyright © 2007 John Wiley & Sons, Ltd.     

The near-field characteristics of circular jets at low Reynolds numbers

An experimental study has been undertaken to investigate the effect of Reynolds number on the near-field region of circular turbulent air jets. Measurements were made using a two-component Laser Doppler Anemometer, and included mean velocity, turbulence intensity, skewness factor, flatness factors and power spectrum. Measurements were taken up to 10 nozzle exit diameter in the downstream direction for different exit Reynolds numbers in the range of 1400 to 20000. The Reynolds number was found to have a strong effect on the jet flow behavior in the near-field region; the centerline velocity decays faster (decay constant = 6.11 for Re = 19400, = 1.35 for Re 1430) and the potential core gets shorter with decreasing Reynolds number. Profile measurements of the skewness and flatness factors indicate that the jet flow becomes more intermittent with decreasing Reynolds number. Power spectrum measurements of the streamwise fluctuating velocities reflects the high energy content of the high Reynolds number jet. It also reveals that there is greater energy at the higher frequencies with increasing Reynolds number.     

Particle image velocimetry investigation on mixing enhancement of non-circular sharp edge nozzles

An experimental study using Particle Image Velocimetry (PIV) on free jets issuing from different orifice plate (OP) nozzles is reported. Mean velocity, turbulence intensity and higher order profiles relevant for large and small scale mixing are considered in the near field and interaction zone (0 < X/D < 20). This is done to determine mixing enhancement due to rectangular, squared, elliptic and triangular nozzles in comparison to circular nozzle results in two orthogonal planes. The effect of Reynolds number on the differences among the nozzle shapes is also considered by performing measurements just after laminar–turbulent transition (Re = 8000) and in the fully turbulent regime (Re = 35,000). The results at low Reynolds number show two classes of jets, i.e. at one side, those closer to axial-symmetric conditions, as circular, square and triangular jets, whereas on the other side those with elongated nozzles as rectangular and elliptic. The reason for the different behavior of the latter is connected to the phenomenon of axis-switching which allows a rearrangement of turbulence over the different velocity components and directions. However, for the highest Reynolds number investigated, all nozzles show similar behavior especially in the jet far field (X/D > 10), thus suggesting a significant Reynolds number dependence of the results.     

A phase averaged PIV study of circular and non-circular synthetic turbulent jets issuing from sharp edge orifices

An extensive experimental study using Particle Image Velocimetry (PIV) on synthetic jets issuing from different orifice shapes is reported. All data are phase and time averaged to derive mean velocity, half-velocity width and rms velocity profiles in the near field of the jet (0 < X/D < 7), at a Reynolds number around 10,000. Different non-circular orifice shapes as rectangular, square, elliptic and triangular are considered and results are compared to those of the circular orifice in order to investigate the effect of asymmetry on the turbulent flow field in view of mixing enhancement. The measurements are carried out on two orthogonal planes to capture three dimensional features of non-circular jets. Results show highest velocity decay rate for elongated orifices, especially the rectangular one, in comparison to the circular one, both in phase and time-averaged plots. Time averaged results show higher velocity decay rate of synthetic jets in comparison to those of continuous ones. It is also observed that, for X/D > 5, only profiles of circular and square jets become partially self-similar. For synthetic jets, higher turbulence content is measured for all orifice shapes at the centerline and close to the orifice exit in comparison to continuous jets.     

Simultaneous velocity and passive scalar concentration measurements in low Reynolds number neutrally buoyant turbulent round jets

Velocity and scalar concentration characteristics of low Reynolds number (Re) neutrally buoyant turbulent round jets were studied using coupled particle image velocimetry and laser induced fluorescence. Experiments were conducted on a jet with a fully developed pipe exit profile at Re = 1,500 and Re = 4,000. Measurements were made in the far field (60 < x/D < 80). Results show that the centerline velocity decay constant increases with Re and the virtual origin is located far from the jet exit. The Re does not have such an influence on the scalar concentration decay constant and scalar field virtual origin. Centerline turbulent intensities show evidence of becoming self-similar past x/D ≈ 75 but the same is not observed in the scalar fluctuations. The latter are strongly influenced by the Re, increasing as entrainment of ambient flow on the jet axis increases as the flow approaches laminar conditions. Scalar fluxes showed a marked Re dependence as well. Results were used to estimate the turbulent Schmidt number which decreases as the Re decreases.     

Study on the radial jet velocity distribution of two closely spaced opposed jets

The experimental and theoretical researches on the radial jet of two opposed jets have been carried out in this paper. The radial velocities of opposed jets with various exit velocities, nozzle diameters and nozzle separations were measured experimentally by a hot-wire anemometer (HWA). The results show that, the normalized radial velocities are self-similar across various radial sections at r ? 1.5D and the radial velocity profiles can be described by a Gaussian distribution function. The half-width increases linearly with increasing radial distance at r ? 1.5D, and spreading rates of radial jet are about 0.121. The normalized radial velocity at impingement plane increases firstly, and then decreases with the increasing normalized radial distance. The normalized radial velocity is independent on nozzle diameter, nozzle separation and exit velocity. The maximum radial velocity at impingement plane is proportional to the exit velocity, and it is inversely proportional to the 0.551th power of the normalized nozzle separation. The position of the maximum radial velocity increases with the nozzle separation at L/D < 1, and keeps invariant at L/D ? 1.     

A plane turbulent wall jet on a fully rough surface

The mean velocity field and skin friction characteristics of a plane turbulent wall jet on a smooth and a fully rough surface were studied using Particle Image Velocimetry. The Reynolds number based on the slot height and the exit velocity of the jet was Re = 13,400 and the nominal size of the roughness was k = 0.44 mm. For this Reynolds number and size of roughness element, the flow was in the fully rough regime. The surface roughness results in a distinct change in the shape of the mean velocity profile when scaled in outer coordinates, i.e. using the maximum velocity and outer half-width as the relevant velocity and length scales, respectively. Using inner coordinates, the mean velocity in the lower region of the inner layer was consistent with a logarithmic profile which characterizes the overlap region of a turbulent boundary layer; for the rough wall case, the velocity profile was shifted downward due to the enhanced wall shear stress. For the fully rough flow, the decay rate of the maximum velocity of the wall jet is increased, and the skin friction coefficient is much larger than for the smooth wall case. The inner layer is also thicker for the rough wall case. The effects of surface roughness were observed to penetrate into the outer layer and slightly enhance the spread rate for the outer half-width, which was not observed in most other studies of transitionally rough wall jet flows.     

Flows of Supersonic Underexpanded Jets on the Range of Moderate Reynolds Numbers

The results of an experimental investigation of the gasdynamic structure of supersonic underexpanded air jets flowing out of a sonic nozzle into a low-pressure medium are presented. This setting of the experimentmakes it possible to achieve high values of the nozzle-to-ambient pressure ratio at moderate outflow Reynolds numbers characteristic of underexpanded jets issuing from micronozzles. The data on the supersonic core length, the laminar-turbulent transition location, and the jet flow characteristics are obtained. The results are compared with those obtained in microjets flowing out of sonic nozzles. Emphasis is placed on the earlier discovered effect of inverse transition of a turbulent jet into the laminar flow regime with increase in the Reynolds number.     

Phase-locked analysis of velocity fluctuations in a turbulent free swirling jet after vortex breakdown

Large-scale organized vortical structures were studied experimentally in a free swirling jet of air experiencing vortex precession (PVC) at ambient conditions. Detailed measurements were performed in the region near the nozzle exit using phase-locked LDV and PIV, at a Reynolds number of Re ?? 24,400 and a swirl parameter S ?? 1.0. The investigation allowed reconstruction of the time-averaged flowfield, with the associated distribution of turbulent fluctuations, the phase-locked structure of the jet and the associated precessing vortex structure. An original joint analysis of power spectra and probability density functions of velocity data led to quantification of the PVC effect on turbulent fluctuations. This analysis showed that the PVC contribution can be properly separated from the background random turbulence, reproducing the results of phase-locked measurements. It is found that the background turbulence in the near field is substantially weaker if compared to the coherent fluctuations induced by vortex precession.     

Flow and acoustic features of a supersonic tapered nozzle

The acoustic and flow characteristics of a supersonic tapered jet were measured for free and shrouded flow configurations. Measurements were performed for a full range of pressure ratios including over- and underexpanded and design conditions. The supersonic tapered jet is issued from a converging-diverging nozzle with a 31 rectangular slotted throat and a conical diverging section leading to a circular exit. The jet was compared to circular and rectangular supersonic jets operating at identical conditions. The distinct feature of the jet is the absence of screech tones in the entire range of operation. Its near-field pressure fluctuations have a wide band spectrum in the entire range of measurements, for Mach numbers of 1 to 2.5, for over- and underexpanded conditions. The free jet's spreading rate is nearly constant and similar to the rectangular jet, and in a shroud, the pressure drop it is inducing is linearly proportional to the primary jet Mach number. This behavior persisted in high adverse pressure gradients at overexpanded conditions, and with nozzle divergence angles of up to 35°, no inside flow separation was observed.