含缺口复合材料层合板的三维有限元失效分析

本文研究了复合材料层合板最终强度计算的有限元理论,讨论了修正的Newton-Raphson迭代方法在层合板失效过程中应力场计算的迭代过程.同时本文建立了带缺口的复合材料层合板三维有限元模型,充分考虑层合板的纤维断裂、基体开裂和分层三种失效模式,采用修正的三维Hashin准则作为失效判断的依据,计算了三种不同铺层的层合板最终失效载荷值,与试验值吻合得很好.鉴于层压板材料常数ν23的数值难于测定的特点,讨论其对最终失效载荷的影响.在三维有限元模型的基础上,实现了失效扩展仿真分析.     

基于累积失效法的含损伤格栅加筋板非线性屈曲状态分析

分别采用基于Mindlin一阶剪切理论八节点层合板单元和三节点层合梁单元来模拟蒙皮和肋骨,用累积失效法研究了在压缩载荷作用下蒙皮内含分层损伤复合材料正交格栅加筋板的非线性屈曲性态,分析中考虑了加载过程中蒙皮和肋骨纤维断裂、基体损伤和纤维-基体剪切失效造成的刚度退化,并采用了非线性接触单元模型处理蒙皮分层上下子板间的接触效应。通过典型算例,讨论了蒙皮铺设方式、蒙皮分层的面积和深度、肋骨与蒙皮的刚度比,累积失效行为等因素对格栅加筋板非线性屈曲性态的影响。     

复合材料铺层拼接层间断裂韧性的试验研究

针对评价复合材料层合板层间断裂韧性的测量,提出了用拉伸试验法测定Ⅱ型层间断裂韧性,设计了内含铺层拼接区的分层破坏试验层合板,制备了拉伸试件.通过拉伸试验测得了拼接区开裂和分层裂纹稳态扩展过程中的载荷与变形规律:层间破坏具有Ⅱ型断裂特征,且裂纹扩展比较稳定.利用测试数据计算出断裂功,并以临界能量释放率表示层合板的Ⅱ型层间断裂韧性,结果表明用铺层拼接件拉伸法进行层间断裂韧性试验是可行的.     

考虑面内破坏过程的含分层损伤复合材料加筋层合板的动力响应

基于复合材料层合板一阶剪切理论，推导了复合材料层合板单元的刚度阵和质量阵列式；同时采用了Adams应交能法与Rayleigh阻尼模型相结合的方法，构造了相应的阻尼阵列式；为了防止在低阶模态中分层处出现的上、下子板不合理的嵌入现象，建立了含分层损伤复合材料加筋层合板动力分析的分层分析模型和虚拟界面联接模型。在上述模型和理论基础上，采用了Tsai提出的刚度退化准则和动力响应分析的精细积分法，对含分层损伤复合材料加筋层合板结构进行了动力响应和破坏分析。通过算例，分别讨论了外载频率、分层位置，以及破坏过程的刚度退化对含损伤复合材料加筋层合板动力响应特征的影响，得到了一些具有理论和工程价值的结论。     

具有分层损伤的不同加筋形式复合材料层合板的后屈曲性态研究

基于板的一阶剪切理论和V on-K arm an大挠度理论,分别推导了复合材料层合板和层合梁的几何非线性有限元列式,提出了含嵌入分层的复合材料加筋层合板在受压缩载荷作用下的后屈曲有限元分析方法,对在板厚方向具有不同分层位置的加筋板结构进行了有限元数值分析,研究了不同的加筋方式及筋的分布对具有分层损伤的复合材料加筋层合板的后屈曲性态的影响,所得结果对确定在压缩载荷作用下含损伤复合材料加筋层合板的剩余承载能力具有参考价值。     

复合材料层合板分层裂纹扩展的试验及数值模拟研究

由于复合材料层合板在制作加工过程中会产生初始的微裂纹,且复合材料具有各向异性的力学特征,因此在承载条件下,这些微裂纹可能在黏结面上及在层与层之间发生、扩展、发展成宏观层间裂纹,最终导致结构的破坏.本文对复合材料层合板试验件进行了拉伸试验,提出了一种复合材料层合板分层建模方法,利用这种方法对一组试验件进行了单向拉伸荷载作用下极限承载力的研究,得出其分层扩展的位置及层间应力分布规律,将试验结果与数值模拟结果进行了对比,论证了分层建模方法对分析复合材料层合板分层裂纹扩展问题的可行性与适用性.     

含有分层损伤的复合材料加筋层合板的屈曲性态研究

基于Ｍｉｎｄｉｎ假定推导了考虑剪切的复合材料加筋层板的有限元列式,并在此基础上计算出筋间基板含嵌入分层以及筋与基板连接处含穿透分层的加筋层合板在受压缩载荷情况下的屈曲模式和临界力。本文所给出的有限元方法及结论对从事复合材料结构设计的工程人员具有参考价值。     

含分层损伤复合材料层合板分层扩展研究

采用基于Ｍｉｎｄｌｉｎ－阶剪切理论的四节点板单元,分析了含椭圆分层合板分层扩展行为。利用虚裂纹闭合技术计算分层前缘处的总能量释放率,并采用总能量释放率准则作为扩展准则,结合自适应网格移动技术,并考虑了分层前缘闭合接角效应,对 合材料层合板的分层扩展行为进行了模拟分析。结果表明,初始分层形状对其扩展有方式有限大影响。     

含分层损伤的变角度纤维层合板后屈曲力学行为研究

变角度（Variable angle tow,简称VAT）纤维复合材料层合板的纤维方向能够连续变化．相较于传统的直线纤维层合板,此类层合板通过刚度变化,整体的屈曲性能可以得到很大的提升．本文利用ABAQUS 自带的粘结单元(Cohesive Element)对预制圆形分层的变角度纤维复合材料层合板进行了后屈曲力学行为研究,得出载荷位移曲线,以及分层裂纹萌生和扩展的情况．然后本文分析了预制分层尺寸对板的刚度、前后屈曲阶段和裂纹萌生及扩展的影响．最后通过变角度纤维层合板和直线纤维层合板的后屈曲力学行为进行对比,深入探索了变角度复合材料层合板在抵抗分层裂纹萌生和扩展方面的优势．     

复合材料层合板低速冲击损伤分析的连续介质损伤力学模型

针对复合材料层合板低速冲击损伤问题,提出了一种各向异性材料连续介质损伤力学模型,模型涵盖损伤表征、损伤起始判定和损伤演化法则3 个方面. 通过材料断裂面坐标下的损伤状态变量矩阵完成损伤表征,并考虑断裂面角度的影响,建立了主轴坐标系下的材料损伤本构关系. 损伤起始由卜克(Puck) 失效准则预测,损伤演化由断裂面上的等效应变控制,服从基于材料应变能释放的线性软化行为. 模型区分了纤维损伤和基体损伤,并根据冲击载荷下层内产生多条基体裂纹继而扩展至界面形成层间裂纹(分层) 的试验观察,引入基体裂纹饱和密度参数表征层间分层. 以[0₃/45/-45]_S 和[45/0/-45/90]_4S 两种铺层的复合材料层合板为例,预测了不同冲击能量下复合材料层合板的低速冲击损伤响应参数,试验结果证明了连续介质损伤力学模型的有效性.模型在不同网格密度下的计算结果表明单元特征长度的引入可以在一定程度上降低损伤演化阶段对网格密度的依赖性.      

Determination of mode II fracture toughness for U-shaped notches using Brazilian disc specimen

A brittle fracture criterion is proposed for predicting fracture toughness of U-shaped notches under pure mode II loading. The criterion, called UMTS, is developed based on the maximum tangential stress (MTS) criterion. The UMTS criterion can be generally used for determining the mode II fracture toughness of U-notched components as well as the fracture initiation angle in U-shaped notches under pure mode II loading. To verify the validity of the proposed criterion, a set of experiments were carried out on the U-notched Brazilian disc (UNBD) specimens made of PMMA and also soda-lime glass. It is shown that there is a good agreement between the results of the UMTS criterion and the experimental results both for fracture toughness and for the fracture initiation angle under pure mode II conditions.     

Experimental and Theoretical Assessment of Brittle Fracture in Engineering Components Containing a Sharp V-Notch

A criterion was proposed to predict brittle fracture in engineering components containing sharp V-shaped notches and subjected to mixed mode I/II loading. The criterion, called SV-MTS, was developed based on the maximum tangential stress (MTS) criterion proposed originally for analyzing crack problems. The curves which are obtained from the SV-MTS criterion could be used conveniently to predict the fracture resistance and also the notch bifurcation angle in sharp V-notched components under pure mode II and also mixed mode loading. To evaluate the validity of the proposed criterion, a set of fracture tests were conducted on a new test specimen, called sharp V-notched Brazilian disc (SV-BD), under mixed mode loading conditions. It is shown that the experimental results obtained from PMMA specimens are in very good agreement with the curves of SV-MTS criterion.     

A MIXED MODE FRACTURE CRITERION BASED ON THE MAXIMUM TANGENTIAL STRESS IN BRITTLE INCLUSION

A closed-form solution for predicting the tangential stress of an inclusion located in mixed mode Ⅰ and Ⅱ crack tip field was developed based on the Eshelby equivalent inclusion theory. Then a mixed mode fracture criterion, including the fracture direction and the critical load, was established based on the maximum tangential stress in the inclusion for brittle inclusioninduced fracture materials. The proposed fracture criterion is a function of the inclusion fracture stress, its size and volume fraction, as well as the elastic constants of the inclusion and the matrix material. The present criterion will reduce to the conventional one as the inclusion having the same elastic behavior as the matrix material. The proposed solutions are in good agreement with detailed finite element analysis and measurement.     

广义平均形状改变能密度断裂准则及应用

基于形状改变能为材料起裂扩展控制参量的物理事实及裂纹尖端断裂控制区能量平均概念,提出了计及裂纹尖端应力场特征级数展开奇异项和常数项的广义平均形状改变能密度(GADSED)准则,建立了I-II-III 混合型裂纹断裂判据计算式,为工程结构疲劳断裂评估提供了新选择．基于提出的GADSED 准则,系统分析了T应力对裂纹断裂判据的影响,结果表明：当参数|Ba|数值相同时：负值T应力的I-II 混合型裂纹更易起裂扩展,正值T应力的KΙf值高于负值T应力的KΙf值,正负T应力的KIIf值相同;T应力在区间0 < Bα < 0.45 时增大了KΙf值（3 %以内）,T应力降低了KIIf值．根据GADSED 准则完成了双轴疲劳载荷平板表面I 型裂纹扩展寿命预报,结果表明：基于GADSED 准则的裂纹扩展寿命预报值约为传统方法预报值的40.7 %,可为工程实际评估提供借鉴．     

Free Surface Fracture in Three Upsetting Tests

The results of three different upsetting tests on steel C1530 are presented. The die design is shown to have a marked effect on free surface fracture. A popular empirical ductile fracture criterion (Oyane's criterion) is assessed by means of the experimental data obtained and by a theoretical approach for determining the workability diagram from free surface fracture data. It is shown that the criterion is not appropriate for the material investigated. The range of free surface conditions where experimental fracture data are required for formulating an accurate fracture criterion is specified and a number of tests to create such conditions is proposed.     

基于分子动力学的结合材料界面破坏准则

结合材料的破坏通常都是从界面或其附近发生的,但界面破坏的机理及其评价准则尚未十分清楚.采用分子动力学模拟方法,可以对结合材料的界面破坏过程进行模拟,从而获得结合材料的界面应力和界面破坏之间的关系.界面破坏可以分为奇异应力场作用下的破坏,和界面应力集中引起的破坏两种.虽然在分子动力学模拟中采用了高度简化的界面模型,但对界面破坏过程的模拟,仍可以帮助人们获得结合材料界面破坏过程的规律性认识.分别模拟远场作用下界面上存在初始裂纹和界面附近存在初始裂纹两种情况下的界面破坏,根据分子动力学模拟结果,提出了一个结合材料界面破坏的准则.     

Prefracture zone for longitudinal shear cracks in structured materials

We obtain simple relations for the following critical fracture parameters of elastoplastic materials: the shear stresses, the prefracture zone length, and the stress intensity factor for mode III of fracture. There is a passage to the limit from a sufficient fracture criterion to a necessary fracture criterion as the prefracture zone length tends to zero. The critical stresses obtained from the necessary and sufficient criteria are substantially different. In the framework of the proposed model, the critical stress intensity factor obtained from the sufficient criterion depends on the grain diameter and the parameters of the τ-γ diagram of the material.     

On the temperature dependence of fracture toughness in the brittle-to-ductile transition region

A method for calculation of fracture toughness in the brittle-to-ductile transition region is proposed for a known fracture toughness at a given temperature and a known temperature dependence of the yield point. A two-parameter quasi-brittle fracture criterion proposed earlier is employed. This criterion contains in explicit form a plastic constraint factor that is sensitive to temperature variation under plane strain conditions. The obtained calculation dependence is compared with experimental data for four structural steels. S. P. Timoshenko Institute of Mechanics, National Academy of Sciences of Ukraine, Kiev, Ukraine. Translated from Prikladnaya Mekhanika, Vol. 35, No. 4, pp. 80–86, April, 1999.     

EVALUATION OF DUCTILE FRACTURE CRITERIA IN A GENERAL THREE-DIMENSIONAL STRESS STATE CONSIDERING THE STRESS TRIAXIALITY AND THE LODE PARAMETER

This paper is concerned with evaluation of various ductile fracture criteria in a general three-dimensional stress state of stress triaxiality, the Lode parameter and the equiva- lent plastic strain to fracture. Evaluation is carried out by comparing fracture loci constructed by fracture criteria to experimental results of A12024-T351. Comparison demonstrates that the Modified Mohr-Coulomb criterion and a newly proposed criterion provide sufficient predictabil- ity of fracture strain. Moreover, evaluation is emphasized on the predicted cut-off value for stress triaxiality. The evaluation demonstrates that the Cockcroft-Latham, Brozzo, Oh, Ko-Huh and the new criteria coupled a reasonable cut-off value for ductile materials.     

On constructing the theory of ductile fracture near friction surfaces

A criterion of ductile fracture is proposed, which takes into account the singular character of theoretical solutions near the maximum friction surfaces and the emergence of a thin layer with intense plastic strains near surfaces with high friction stresses in real processes of metal forming. The equation for the thickness of the layer with intense plastic strains and the fracture criterion include the strain rate intensity factor, apparently, characterizing the intensity of physical processes that occur in a thin material layer near the friction surfaces. Some experimental data are used to determine the thickness of this layer. The ductile fracture criterion is analyzed by solving the problem of strip extrusion under conditions of plane strain deformation.